- Copy stable/10@296371 to releng/10.3 in preparation for 10.3-RC1
builds.
- Update newvers.sh to reflect RC1.
- Update __FreeBSD_version to reflect 10.3.
- Update default pkg(8) configuration to use the quarterly branch.

Approved by: re (implicit)

MFC r291149, r291367:

Update the imx5/imx6 cpu_reset() implementation based on a new understanding
of the SRS (software reset) bit in the watchdog control register. Despite
what the manual seems to imply, this bit DOES trigger an immediate reset, as
opposed to simply flagging the type of reset as software-triggered.

Rename sysctl node hw.imx6 to hw.imx. Move its definition to imx_machdep.c
so that code shared between imx5 and imx6 can work with OIDs under that node.

Add last_reset_status (integer) and last_reset_reason (string) OIDs that
provide info about the last chip reset (power-on, software reset, watchdog
timeout).

MFC 264977:

Stop calling imx51_ccm_foo() clock functions from imx6 code. Instead
define a few imx_ccm_foo() functions that are implemented by the imx51
or imx6 ccm code.

MFC r261803, r261808, r261814, r261815, r261816, r261817, r261818, r261826,
r261848, r261855

On armv6 and later, use the WriteNotRead bit of the fault status register
to decide what protections are required by the faulting access.

Use the right symbols for determining arm architecture. Include the
necessary header file which has the new FAULT_WNR symbol defined in it.

Allow the kernel to be loaded at any 1MiB address. This requirement is
because we use the 1MiB section maps as they only need a single pagetable.

Add function for configuring Vybrid PLL4 (Audio) clock frequency output.

imx6 changes ...

- Fix the definition of the SDHCI_STATE_DAT and SDHCI_STATE_CMD fields,
and add SDHCI_RETUNE_REQUEST. None of these are actually used in the
code yet.

- Write translation code for the SDHCI_PRESENT_STATE register.
Freescale moved some bits around in their version of the register,
adjust things so that the sdhci code sees the standard layout.

- Add standard non-removable and cd-gpios properties to the usdhc
devices. That generates references to gpio devices, so uncomment them
even though there isn't a gpio driver to do anything with them yet.

- Add handling of standard "non-removable" property, and also some
workaround code so that if card detect is wired to a gpio pin, for now
we just treat it the same as non-removable (because there isn't a gpio
driver yet).

- Enable both sdcard slots, but not the sdio-based wifi that we don't
yet have a driver for.

- Remove a couple obsolete function declarations.

MFC r257476, r257478:

Revamp the SoC identity numbering scheme to be more in line with the way
Freescale numbers the chips in the ID registers.

Add definitions for the register and data that describes the SoC type.

MFC r257383, r257384:

Add some bare-bones support for enabling usb and usbphy clocks.

Add a "no-op" USB PHY driver for imx-family SoCs.

MFC r257197:

Maximize available kva space by doing static device mapping from the top
of the address space downwards, and then returning the lowest mapped
device address from initarm_lastaddr(). Premap most of the device's
on-chip peripherals.

Maximize available kva space by doing static device mapping from the top
of the address space downwards, and then returning the lowest mapped
device address from initarm_lastaddr(). This adds over 500MB of kva
space compared to the old way of hardcoding the end address as 0xE0000000.

Also, pre-map most of the SoC's common memory-mapped devices using 1MB
section mappings so that all device access uses just a few TLB entries.
Graphics devices aren't mapped this way yet, but probably should be.

To provide this new functionality without pasting identical code into
multiple imxNN_machdep.c files, rework the imx machdep code so that
things common to the whole family of SoCs are in a new imx_machdep.c file.
The rewritten imxNN_machdep.c files contain just things specific to an
individual SoC.