- Copy stable/10@285827 to releng/10.2 in preparation for 10.2-RC1
builds.
- Update newvers.sh to reflect RC1.
- Update __FreeBSD_version to reflect 10.2.
- Update default pkg(8) configuration to use the quarterly branch.[1]

Discussed with: re, portmgr [1]
Approved by: re (implicit)
Sponsored by: The FreeBSD Foundation

Copy head (r256279) to stable/10 as part of the 10.0-RELEASE cycle.

Approved by: re (implicit)
Sponsored by: The FreeBSD Foundation

- Merge the *_SET macros from fire(4) which generally print out the
register changes when compiled with SCHIZO_DEBUG and take advantage
of them.
- Add support for the XMITS Fireplane/Safari to PCI-X bridges. I tought
I'd need this for a Sun Fire 3800, which then turned out to not being
equipped with such a bridge though. The support for these should be
complete but given that it hasn't actually been tested probing is
disabled for now.
This required a way to alter the XMITS configuration in case a PCI-X
device is found further down the device tree so the sparc64 specific
ofw_pci kobj was revived with a ofw_pci_setup_device method, which is
called by the ofw_pcibus code for every device added.
- A closer inspection of the OpenSolaris code indicates that consistent
DMA flushing/syncing as well as the block store workaround should be
applied with every BUS_DMASYNC_POSTREAD instead of in a wrapper around
interrupt handlers for devices behind PCI-PCI bridges only as suggested
by the documentation (code for the latter actually exists in OpenSolaris
but is disabled by default), which also makes more sense.
- Add a workaround for Casinni/Skyhawk combinations. Chances are that
this solves the crashes seen when using the the on-board Casinni NICs
of Sun Fire V480 equipped with centerplanes other than 501-6780 or
501-6790. This also takes advantage of the ofw_pci_setup_device method.
- Mark some unused parameters as such.

- Enable DMA write parity error interrupts on Schizo with a working
implementation.
- Revert the Sun Fire V890 WAR of r205254. Instead let schizo_pci_bus()
only panic in case of fatal errors as the interrupt triggered by the
error the firmware of these and also Sun Fire 280R with version 7
Schizo caused may happen as late as using the HBA and not only prior
to touching the PCI bus (in the former case the actual error still is
fatal but we clear it before touching the PCI bus).
While at it count and export non-fatal error interrupts via sysctl(9).
- Remove unnecessary locking from schizo_ue().

- According to OpenSolaris, CDMA flushing/syncing for Tomatillos
and XMITS has to be basically done in the same manner as for
the Sabres, i.e. only for devices behind PCI-PCI-bridges and
after a PIO read on the far side of the farest PCI-PCI-bridge.
Given that the Tomatillo documentation mentions no difference
to the Schizo bridges in this regard and this is also still
part of the procedure described Schizo documentation this
seems about right so adjust accordingly (the unconditional
CDMA flushing/syncing previously done was based on how Linux
behaves).
- Implement CDMA flushing/syncing for Schizo version >= 5,
which requires the workaround described in Schizo Errata I-23.
According to Schizo Errata I-13 it's just unusable with
version < 5 though. [1]
- Don't register the Schizo streaming buffer for now until it's
usage is sorted out according to the erratas.
- Register our interrupt filters with the revived INTR_FAST so
they these interrupts can even interrupt filters of device
drivers as necessary.
- Remove the comment regarding lack of newbus'ified bus_dma(9)
as being able to associate a DMA tag with a device would
allow to implement CDMA flushing/syncing in bus_dmamap_sync(9)
but that would totally kill performance. Given that for devices
not behind a PCI-PCI bridge the host-to-PCI bridges also only
do CDMA flushing/syncing based on interrupts there's no
additional disadvantage for polling(4) callbacks in the case
schizo(4) has to do the CDMA flushing/syncing but rather a
general problem.

Reported by: Michael Moll [1]

Add a driver for `Schizo' Fireplane/Safari to PCI 2.1 and `Tomatillo'
JBus to PCI 2.2 bridges. In theory, this driver should also handle
`XMITS' Fireplane/Safari to PCI-X bridges but due to lack of access
to such hardware, support for these hasn't be fleshed out, yet.