- Copy stable/10@285827 to releng/10.2 in preparation for 10.2-RC1
builds.
- Update newvers.sh to reflect RC1.
- Update __FreeBSD_version to reflect 10.2.
- Update default pkg(8) configuration to use the quarterly branch.[1]

Discussed with: re, portmgr [1]
Approved by: re (implicit)
Sponsored by: The FreeBSD Foundation

Copy head (r256279) to stable/10 as part of the 10.0-RELEASE cycle.

Approved by: re (implicit)
Sponsored by: The FreeBSD Foundation

-----------
MISC CHANGES

Add a new async event- ISP_TARGET_NOTIFY_ACK, that will guarantee
eventual delivery of a NOTIFY ACK. This is tons better than just
ignoring the return from isp_notify_ack and hoping for the best.

Clean up the lower level lun enable code to be a bit more sensible.

Fix a botch in isp_endcmd which was messing up the sense data.

Fix notify ack for SRR to use a sensible error code in the case
of a reject.

Clean up and make clear what kind of firmware we've loaded and
what capabilities it has.
-----------
FULL (252 byte) SENSE DATA

In CTIOs for the ISP, there's only a limimted amount of space
to load SENSE DATA for associated CHECK CONDITIONS (24 or 26
bytes). This makes it difficult to send full SENSE DATA that can
be up to 252 bytes.

Implement MODE 2 responses which have us build the FCP Response
in system memory which the ISP will put onto the wire directly.

On the initiator side, the same problem occurs in that a command
status response only has a limited amount of space for SENSE DATA.
This data is supplemented by status continuation responses that
the ISP pushes onto the response queue after the status response.
We now pull them all together so that full sense data can be
returned to the periph driver.

This is supported on 23XX, 24XX and 25XX cards.

This is also preparation for doing >16 byte CDBs.

-----------
FC TAPE

Implement full FC-TAPE on both initiator and target mode side. This
capability is driven by firmware loaded, board type, board NVRAM
settings, or hint configuration options to enable or disable. This
is supported for 23XX, 24XX and 25XX cards.

On the initiator side, we pretty much just have to generate a command
reference number for each command we send out. This is FCP-4 compliant
in that we do this per ITL nexus to generate the allowed 1 thru 255
CRN.

In order to support the target side of FC-TAPE, we now pay attention
to more of the PRLI word 3 parameters which will tell us whether
an initiator wants confirmed responses. While we're at it, we'll
pay attention to the initiator view too and report it.

On sending back CTIOs, we will notice whether the initiator wants
confirmed responses and we'll set up flags to do so.

If a response or data frame is lost the initiator sends us an SRR
(Sequence Retransmit Request) ELS which shows up as an SRR notify
and all outstanding CTIOs are nuked with SRR Received status. The
SRR notify contains the offset that the initiator wants us to restart
the data transfer from or to retransmit the response frame.

If the ISP driver still has the CCB around for which the data segment
or response applies, it will retransmit.

However, we typically don't know about a lost data frame until we
send the FCP Response and the initiator totes up counters for data
moved and notices missing segments. In this case we've already
completed the data CCBs already and sent themn back up to the periph
driver. Because there's no really clean mechanism yet in CAM to
handle this, a hack has been put into place to complete the CTIO
CCB with the CAM_MESSAGE_RECV status which will have a MODIFY DATA
POINTER extended message in it. The internal ISP target groks this
and ctl(8) will be modified to deal with this as well.

At any rate, the data is retransmitted and an an FCP response is
sent. The whole point here is to successfully complete a command
so that you don't have to depend on ULP (SCSI) to have to recover,
which in the case of tape is not really possible (hence the name
FC-TAPE).

Sponsored by: Spectralogic
MFC after: 1 month

Revamp the pieces of some of the stuff I forgot to do when shifting to
32 bit handles. The RIO (reduced interrupt operation) and fast posting
for the parallel SCSI cards were all 16 bit handles. Furthermore,
target mode parallel SCSI only can have 16 bit handles.

Use part of a supplied patch to switch over to using 32 bit handles.
Be a bit more conservative here and only do this for parallel SCSI
for the 12160 (Ultra3) cards. There were a lot of marginal Ultra2
cards, and, frankly, few are findable now for testing.

Fix the target handle routine to only do 16 bit handles for parallel
SCSI cards. This is okay because the upper sixteen bits of the new
32 bit handles is a sequence number to help protect against duplicate
completions. This would be very unlikely to happen with parallel
SCSI target mode, and wasn't present before, so we're no worse off
than we used to be.

While we're at it, finally split the async mailbox completion handlers
into FC and parallel SCSI functions. This makes it much cleaner and
easier to figure out what is or isn't a legal async mailbox completion
code for different card classes.

PR: kern/144250
Submitted partially by: Charles D
MFC after: 1 week

Redo how commands handles are created and managed and implement sequence
numbers and handle types in rational way. This will better protect from
(unwittingly) dealing with stale handles/commands.

Fix the watchdog timeout code to better protect itself from mistakes.

If we run an abort on a putatively timed out command, the command
may in fact get completed, so check to make sure the command we're
timing it out is still around. If the abort succeeds, btw, the command
should get returned via a different path.

Add 8Gb support (isp_2500). Fix a fair number of configuration and
firmware loading bugs.

Target mode support has received some serious attention to make it
more usable and stable.

Some backward compatible additions to CAM have been made that make
target mode async events easier to deal with have also been put
into place.

Further refinement and better support for NP-IV (N-port Virtualization)
is now in place.

Code for release prior to RELENG_7 has been stripped away for code clarity.

Sponsored by: Copan Systems

Reviewed by: scottl, ken, jung-uk kim
Approved by: re

Temporarily desupport simultaneous target and initiator mode.

When the linux port changes were imported which split the
target command list to be separate from the initiator command
list and the handle format changed to encode a type in the handle
the implications to the function isp_handle_index (which only
the NetBSD/OpenBSD/FreeBSD ports use) were overlooked.

The fault is twofold: first, the index into the DMA maps
in isp_pci is wrong because a target command handle with
the type bit left in place caused a bad index (and panic)
into dma map. Secondly, the assumption of the array
of DMA maps in either PCS or SBUS attachment structures is
that there is a linear mapping between handle index and
DMA map index. This can no longer be true if there are
overlapping index spaces for initiator mode and target
mode commands.

These changes bandaid around the problem by forcing us
to not have simultaneous dual roles and doing the appropriate
masking to make sure things are indexed correctly. A longer
term fix is being devloped.

MFP4: a) Some constification from NetBSD (gcc 4.1.2)
b) Split default param fetching/setting into scsi and fibre functions
and retry the fibre fetch more than once.

MFC after: 1 week

Fix some stupid copyright mistakes that have been there for quite some time.

Make the SAN login/logout stuff more common between different chipsets
and provied an isp_control entry point so that the outer layers can
do PLOGI/LOGO explicitly. Add MS IOCB support. This completes the cycle
for base support for SMI-S.

Push things closer to path failover by implementing loop down and
gone device timers and zombie state entries. There are tunables
that can be used to select a number of parameters.

loop_down_limit - how long to wait for loop to come back up before
declaring
all devices dead (default 300 seconds)

gone_device_time- how long to wait for a device that has appeared
to leave the loop or fabric to reappear (default 30 seconds)

Internal tunables include (which should be externalized):

quick_boot_time- how long to wait when booting for loop to come up

change_is_bad- whether or not to accept devices with the same
WWNN/WWPN that reappear at a different PortID as being the 'same'
device.

Keen students of some of the subtle issues here will ask how
one can keep devices from being re-accepted at all (the answer
is to set a gone_device_time to zero- that effectively would
be the same thing).

Add 4Gb (24XX) support and lay the foundation for a lot of new stuff.

a) clean up some declaration stuff (i.e., make more modern with respect
to getting rid u_int for uint and so on).

b) Turn back on 64 bit DAC support. Cheeze it a bit in that we have two
DMA callback functions- one when we have bus_addr_t > 4 bits in width and
the other which should be normal. Even Cheezier in that we turn off setting
up DMA maps to be BUS_SPACE_MAXADDR if we're in ISP_TARGET_MODE. More work
on this in a week or so.

c) Tested under amd64 and 1MB DFLTPHYS, sparc64, i386 (PAE, but insufficient
memory to really test > 4GB). LINT check under amd64.

MFC after: 1 month

Remove use of inlines and use the functions as a library.

Larger code space, possibly performance hit, but more portable.
Certainly less questionable use of inlining.

Suggested by: des