Copy stable/10@r272459 to releng/10.1 as part of
the 10.1-RELEASE process.

Approved by: re (implicit)
Sponsored by: The FreeBSD Foundation

MFC r267921, r267934, r267949, r267959, r267966, r268202, r268276,
r268427, r268428, r268521, r268638, r268639, r268701, r268777,
r268889, r268922, r269008, r269042, r269043, r269080, r269094,
r269108, r269109, r269281, r269317, r269700, r269896, r269962,
r269989.

Catch bhyve up to CURRENT.

Lightly tested with FreeBSD i386/amd64, Linux i386/amd64, and
OpenBSD/amd64. Still resolving an issue with OpenBSD/i386.

Many thanks to jhb@ for all the hard work on the prior MFCs !

r267921 - support the "mov r/m8, imm8" instruction
r267934 - document options
r267949 - set DMI vers/date to fixed values
r267959 - doc: sort cmd flags
r267966 - EPT misconf post-mortem info
r268202 - use correct flag for event index
r268276 - 64-bit virtio capability api
r268427 - invalidate guest TLB when cr3 is updated, needed for TSS
r268428 - identify vcpu's operating mode
r268521 - use correct offset in guest logical-to-linear translation
r268638 - chs value
r268639 - chs fake values
r268701 - instr emul operand/address size override prefix support
r268777 - emulation for legacy x86 task switching
r268889 - nested exception support
r268922 - fix INVARIANTS build
r269008 - emulate instructions found in the OpenBSD/i386 5.5 kernel
r269042 - fix fault injection
r269043 - Reduce VMEXIT_RESTARTs in task_switch.c
r269080 - fix issues in PUSH emulation
r269094 - simplify return values from the inout handlers
r269108 - don't return -1 from the push emulation handler
r269109 - avoid permanent sleep in vm_handle_hlt()
r269281 - list VT-x features in base kernel dmesg
r269317 - Mark AHCI fatal errors as not completed
r269700 - Support PCI extended config space in bhyve
r269896 - Minor cleanup
r269962 - use max guest memory when creating IOMMU domain
r269989 - fix interrupt mode names

MFC 266125:
Implement a PCI interrupt router to route PCI legacy INTx interrupts to
the legacy 8259A PICs.

MFC 259942,262274,263035,263054,263211,263744,264179,264324,264468,264631,
264648,264650,264651,266572,267558:
Flesh out the AT PIC and 8254 PIT emulations and move them into the kernel.

MFC 260206:
Rework the DSDT generation code a bit to generate more accurate info about
LPC devices. Among other things, the LPC serial ports now appear as
ACPI devices.

MFC 259826,259997,259998:
Support soft power-off via the ACPI S5 state for bhyve guests and wire
up a virtual power button to SIGTERM:
- Implement the PM1_EVT and PM1_CTL registers required by ACPI.
- Emulate the Reset Control register at I/O port 0xcf9.
- Advertise an _S5 package.
- Implement an SMI_CMD register with commands to enable and disable ACPI.
Currently the only change when ACPI is enabled is to enable the virtual
power button via SIGTERM.
- Implement a fixed-feature power button when ACPI is enabled by asserting
PWRBTN_STS in PM1_EVT when SIGTERM is received.
- Add support for EVFILT_SIGNAL events to mevent.
- Implement support for the ACPI system command interrupt (SCI) and assert
it when needed based on the values in PM1_EVT. Mark the SCI as active-low
and level triggered in the MADT and MP Table.

Support soft power-off via the ACPI S5 state for bhyve guests.
- Implement the PM1_EVT and PM1_CTL registers required by ACPI.
The PM1_EVT register is mostly a dummy as bhyve doesn't support any
of the hardware-initiated events. The only bit of PM1_CNT that is
implemented are the sleep request bits (SPL_EN and SLP_TYP) which
request a graceful power off for S5. In particular, for S5, bhyve
exits with a non-zero value which terminates the loop in vmrun.sh.
- Emulate the Reset Control register at I/O port 0xcf9 and advertise
it as the reset register via ACPI.
- Advertise an _S5 package.
- Extend the in/out interface to allow an in/out handler to request
that the hypervisor trigger a reset or power-off.
- While here, note that all vCPUs in a guest support C1 ("hlt").

Reviewed by: neel (earlier version)