Copy stable/10@r272459 to releng/10.1 as part of
the 10.1-RELEASE process.

Approved by: re (implicit)
Sponsored by: The FreeBSD Foundation

Copy head (r256279) to stable/10 as part of the 10.0-RELEASE cycle.

Approved by: re (implicit)
Sponsored by: The FreeBSD Foundation

Add a GPIO driver for the Gateworks Cambria platform.

The external gpio pins are connected to a PLD on the i2c bus, unfortunatley
this device does not conform by failing to send an ack after each byte written.
The iicbb driver will abort the transfer when the address is not ack'd and it
would introduce a lot of churn to be able to pass a flag down to
iicbb_start/iicbb_write. Instead we do bad things by grabbing the iicbus but
then doing our own bit banging.

Remove line for the uncommitted Cambria gpio drive that snuck in with r214946.

Hook up the five gpio pins on the Avila board to the gpio framework. There are
actually 16 I/O lines but the other ones are used for system devices and
interrupts.

The IXP4XX platform can set interrupts on these pins for
high/low/rising/falling/transitional but this is not implemented yet.

The Cambria has the same interface but as all the pins are assigned to system
functions the gpio header is toggled via a PLD on the i2c bus and is not
supported by this commit.

o add a bus space tag that forces a 2usec delay between r/w ops; this is
used for the optional GPS+RS485 uarts on the Gateworks Cambria boards
which otherwise are unreliable
o setup the hack bus space tag for the GPS+RS485 uarts
o program the gpio interrupts for the uarts to be edge-rising
o force timing on the expansion bus for the uarts to be "slow"

Thanks to Chris Lang of Gateworks for these tips.

Merge support for Gateworks Cambria boards:
o add support for IXP435 cpu's (e.g. 64 irq's)
o add support for Cambria-specific devices: npe, led's (front panel and
octal latch), ehci, mcu, ide cf
o redo memory mapping for xscale/ixp4xx boards: previously memory
was assumed aliased to 0x10000000 but this appears to be true only
for ixp425 systems and breaks operation on others; rework so memory
is assumed to start at 0
o rework NPE configuration support to use NPE id's instead of port #'s;
these changes also rename the associated MAC's to follow the NPE's
they are attached to
o update npe firmware to latest rev (same license) and update default fw
imageid's to match; in particular this adds NPE-A and crypto support
o re-style NPE fw handling code and add a console msg identifying the
attributes of the loaded fw
o fix numerous problems with handling failures during npe setup
o fix npe rx q setup; need to spin waiting for mailbox responses during
early boot stages as qmgr interrupts are not delivered; this fixes
the problem where all 8 traffic classifications were not tied to the
rx q (and eliminates the console msg "remember to fix rx q setup")
o add DELAY to npe MII wait logic for IXP435
o strip down builtin phys->virt address translation table in resource
handling to just those resources that require it and add a console msg
to alert people when this (kludge) table needs to be extended
o purge a bunch of dead netbsd-ism's
o cleanup avila led driver
o add Cambria support to boot2 and rework code for better multi-board support

Notes:
1. NPE-A doesn't work and causes NPE-C to stop working; it is disabled
in the hints
2. USB isn't working yet; controller communicates ok but device
discovery fails
3. Cambria support must be configured separately from IXP425 boards;
multi-board support is TBD

Sponsored by: Hobnob, Gateworks (board donation)
Reviewed by: imp

Remove bus_space_generic.c from the per-plarform files. Having it in the
per-cpu files should be enough.

Refactor certain ARM bus space methods: instead of having multiple copies of
the same code introduce sys/arm/arm/bus_space_generic.c for a shared set of
routines.

Reviewed by: sam
Approved by: cognet (mentor)

Bring in status led support for /dev/led/gpioled on Avila.

Approved by: cognet

Gateworks Avila board support:
o ixp425 support
o NPE network driver (requires Intel microcode)
o h/w qmgr support
o True IDE compact flash over expansion bus
o pci (ath and hifn795x parts tested)
o xscale watchdog timer
o ds1672 RTC on i2c bus
o ad7418 voltage + temp monitoring on i2c bus
o uart

Work done together with cognet, kevlo, and jmg. Parts of
the ixp425 support obtaine/derived from netbsd.

Reviewed by: cognet, imp
MFC after: 1 month