Copy stable/10@r272459 to releng/10.1 as part of
the 10.1-RELEASE process.

Approved by: re (implicit)
Sponsored by: The FreeBSD Foundation

MFC 263301

In kernel config files, it is supposed to be 'options<space><tab>' not
'options<tab><tab>', per long standing (but recently not so strictly
enforced) convention.

MFC 263245: Make all the comments '# ' and align to same column.

MFC 257774, 256760, 262916, 262905, 262918, 262919, 262920, 262921, 262924,
262925, 262929, 262932, 262935, 262940, 262941, 262942, 262948, 262949,
262950

Strip arm/conf/DEFAULTS down to just items that are mandatory for running
the architecture.

Move all the files named foo/common.c to foo/foo_common.c

Initial cut for DTS on the hl201 board.

Add commented out dts for sam9260ek as well as early printf support.

Make clock optional on uart nodes, then back it out ("I don't know what I
was thinking, but it is lame.")

Set the baud rate if it isn't 0

Make at91_soc_id() public.

Properly round at91 resource on unmapping.

Move AT91 AIC related stuff to own file.

Fix another bug in multicast filtering. i.MX uses 6 bits from MSB in
LE CRC32 for the hash value, not the lowest 6 bits in BE CRC32.

Follow r262916 with one more config file that references a renamed common.c

Remove bogus AT91 define that causes compile errors. Most of the defines
for SAM9X are going away soonish anyway (once FDT works), but until
then...

Remove all dregs of a per-thread undefined-exception-mode stack.

Rework the VFP code that handles demand-based save and restore of state.

Always call vfp_discard() on thread death.

When a thread begins life it doesn't own the VFP hardware state on any cpu.

Make undefined exception entry MP-safe.

MFC r261570, r261572

Revert r260440 (add USB_HOST_ALIGN to all configs, it's only needed for
platforms with a 64-byte cacheline size).

Add option USB_HOST_ALIGN=64 for all SoCs that have 64 byte cache lines.

MFC r261252, r261279, r261304, r261305, r261322, r261336, r261337, r261338,
r261353

Fix the name of the dts file for the HL201...

When mapping an address, the bsh needs the same offset we do for other things.

Add explicit depends on bus_if.h and device_if.h to avoid a
chicken and egg problem in some compilation environments.

Switch to using PAs rather than VAs for the addresses we map for
devices. This is a nop, except for what's reported by atmelbus for the
resources.

Comment cleanups. Move things around for diff reduction against FDT work.

MFC r260695, r260696, r260884, r260885, r260886, r260887

Provide a simplified way to specify GPIO pins for the Atmel port.

Add at91 data so we can convert a PIO unit number into a base address.

Add at91 standard memory controller helper functions.

Generalize AT91 NAND support a bit.

Connect NAND for the SAM9260EK eval board, as well as the HotE HL-201.

Add nand device and NANDFS into the mix for those at91 boards that have
support for it at the moment.

MFC r260440, r260441, r260447, r260490, r260493

Add option USB_HOST_ALIGN to configs that contain 'device usb'.

Update dts files of Cubieboard1,2 to use 1GB memory.

Add a function to print the contents of the static device mapping table,

Copy head (r256279) to stable/10 as part of the 10.0-RELEASE cycle.

Approved by: re (implicit)
Sponsored by: The FreeBSD Foundation

Back out r253779 & r253786.

Decouple yarrow from random(4) device.

* Make Yarrow an optional kernel component -- enabled by "YARROW_RNG" option.
The files sha2.c, hash.c, randomdev_soft.c and yarrow.c comprise yarrow.

* random(4) device doesn't really depend on rijndael-*. Yarrow, however, does.

* Add random_adaptors.[ch] which is basically a store of random_adaptor's.
random_adaptor is basically an adapter that plugs in to random(4).
random_adaptor can only be plugged in to random(4) very early in bootup.
Unplugging random_adaptor from random(4) is not supported, and is probably a
bad idea anyway, due to potential loss of entropy pools.
We currently have 3 random_adaptors:
+ yarrow
+ rdrand (ivy.c)
+ nehemeiah

* Remove platform dependent logic from probe.c, and move it into
corresponding registration routines of each random_adaptor provider.
probe.c doesn't do anything other than picking a specific random_adaptor
from a list of registered ones.

* If the kernel doesn't have any random_adaptor adapters present then the
creation of /dev/random is postponed until next random_adaptor is kldload'ed.

* Fix randomdev_soft.c to refer to its own random_adaptor, instead of a
system wide one.

Submitted by: arthurmesh@gmail.com, obrien
Obtained from: Juniper Networks
Reviewed by: obrien

Remove ctl(4) from GENERIC. Also remove 'options CTL_DISABLE'
and kern.cam.ctl.disable tunable; those were introduced as a workaround
to make it possible to boot GENERIC on low memory machines.

With ctl(4) being built as a module and automatically loaded by ctladm(8),
this makes CTL work out of the box.

Reviewed by: ken
Sponsored by: FreeBSD Foundation

Note about where we can boot this.

Add usb_template for the gadget support. Even though this isn't a
bootable kernel, its config will likely be copied to places that are.

Submitted by: Hans Petter Selasky

Add gadget devices. Not yet added to the child lists, but here to
keep things from bit-rotting.

Neither of these systems has PCI, but they do have ohci interface, so
fix comments.

Add new at91sam9g45 support and sn9g45 board to the ATMEL kernel.
Adapt SN9G45 board support to cope with multi-board.

Add preliminary support for Atmel SAM9260-EK evaluation kit.
Initially identical to the Ethernut5, but will diverge shortly before
I refactor...

Create a generic way to support multiple boards within an
arm platform. Add all the atmel boards to the ATMEL kernel for
testing purposes. Until boot loader arg parsing of baord type
is done, this won't actually be able to do the runtime selection.

Create a pseudo-lint kernel for all at91 SoCs. This kernel will not
currently boot, but will serve as a good linting. make universe could
now be altered to skip building all the other at91 kernels...