#
259065 |
|
07-Dec-2013 |
gjb |
- Copy stable/10 (r259064) to releng/10.0 as part of the 10.0-RELEASE cycle. - Update __FreeBSD_version [1] - Set branch name to -RC1
[1] 10.0-CURRENT __FreeBSD_version value ended at '55', so start releng/10.0 at '100' so the branch is started with a value ending in zero.
Approved by: re (implicit) Sponsored by: The FreeBSD Foundation |
#
256281 |
|
10-Oct-2013 |
gjb |
Copy head (r256279) to stable/10 as part of the 10.0-RELEASE cycle.
Approved by: re (implicit) Sponsored by: The FreeBSD Foundation
|
#
236987 |
|
13-Jun-2012 |
imp |
trim trailing spaces that have accumulated over the years (these files served as the basis for too many other platforms).
|
#
215319 |
|
14-Nov-2010 |
thompsa |
Provide a mutex around the read/modify/write of the IXP425_GPIO_* registers. Giant was used in some places, but not all.
|
#
194015 |
|
11-Jun-2009 |
avg |
strict kobj signatures: number of fixes for arm architecture
no functional changes should result
Reviewed by: imp, current@ Approved by: jhb (mentor)
|
#
186352 |
|
20-Dec-2008 |
sam |
Merge support for Gateworks Cambria boards: o add support for IXP435 cpu's (e.g. 64 irq's) o add support for Cambria-specific devices: npe, led's (front panel and octal latch), ehci, mcu, ide cf o redo memory mapping for xscale/ixp4xx boards: previously memory was assumed aliased to 0x10000000 but this appears to be true only for ixp425 systems and breaks operation on others; rework so memory is assumed to start at 0 o rework NPE configuration support to use NPE id's instead of port #'s; these changes also rename the associated MAC's to follow the NPE's they are attached to o update npe firmware to latest rev (same license) and update default fw imageid's to match; in particular this adds NPE-A and crypto support o re-style NPE fw handling code and add a console msg identifying the attributes of the loaded fw o fix numerous problems with handling failures during npe setup o fix npe rx q setup; need to spin waiting for mailbox responses during early boot stages as qmgr interrupts are not delivered; this fixes the problem where all 8 traffic classifications were not tied to the rx q (and eliminates the console msg "remember to fix rx q setup") o add DELAY to npe MII wait logic for IXP435 o strip down builtin phys->virt address translation table in resource handling to just those resources that require it and add a console msg to alert people when this (kludge) table needs to be extended o purge a bunch of dead netbsd-ism's o cleanup avila led driver o add Cambria support to boot2 and rework code for better multi-board support
Notes: 1. NPE-A doesn't work and causes NPE-C to stop working; it is disabled in the hints 2. USB isn't working yet; controller communicates ok but device discovery fails 3. Cambria support must be configured separately from IXP425 boards; multi-board support is TBD
Sponsored by: Hobnob, Gateworks (board donation) Reviewed by: imp
|
#
181303 |
|
04-Aug-2008 |
jhb |
Add locking to the various iicbus(4) bridge drivers: - Just grab Giant in the ixp425_iic(4) driver since this driver uses a shared address/data register window pair to access the actual I2C registers. None of the other ixp425 drivers lock access to these shared address/data registers yet and that would need to be done before this could use any meaningful locking. - Add locking to the interrupt handler and 'iicbus_reset' methods of the at91_twi(4) driver. - Add locking to the pcf(4) driver. Other pcf(4) fixes include: - Don't needlessly zero the softc. - Use bus_foo rather than bus_space_foo and remove bus space tag and handle from softc. - The lpbb(4) driver just grabs Giant for now. This will be refined later when ppbus(4) is locked. - As was done with smbus earlier, move the DRIVER_MODULE() lines to match the bus driver (either iicbus or iicbb) to the bridge driver into the bridge drivers.
Tested by: sam (arm/ixp425)
|
#
176759 |
|
03-Mar-2008 |
kevlo |
Convert to be a 2-clause bsd-only license.
Pointed out by: rwatson
|
#
164426 |
|
19-Nov-2006 |
sam |
Gateworks Avila board support: o ixp425 support o NPE network driver (requires Intel microcode) o h/w qmgr support o True IDE compact flash over expansion bus o pci (ath and hifn795x parts tested) o xscale watchdog timer o ds1672 RTC on i2c bus o ad7418 voltage + temp monitoring on i2c bus o uart
Work done together with cognet, kevlo, and jmg. Parts of the ixp425 support obtaine/derived from netbsd.
Reviewed by: cognet, imp MFC after: 1 month
|