- Copy stable/10 (r259064) to releng/10.0 as part of the
10.0-RELEASE cycle.
- Update __FreeBSD_version [1]
- Set branch name to -RC1

[1] 10.0-CURRENT __FreeBSD_version value ended at '55', so
start releng/10.0 at '100' so the branch is started with
a value ending in zero.

Approved by: re (implicit)
Sponsored by: The FreeBSD Foundation

Copy head (r256279) to stable/10 as part of the 10.0-RELEASE cycle.

Approved by: re (implicit)
Sponsored by: The FreeBSD Foundation

Add a real dependency on the microcode.
Now when one does 'make kernel ; make kernel' the second invocation
only does: `kernel.ko' is up to date.
rather than reproduce all the binary microcode files and relink the kernel.
[continuation of r212429]

Intel XScale hwpmc(4) support.

This brings hwpmc(4) support for 2nd and 3rd generation XScale cores.
Right now it's enabled by default to make sure we test this a bit.
When the time comes it can be disabled by default.
Tested on Gateworks boards.

A man page is coming.

Obtained from: //depot/user/rpaulo/xscalepmc/...

Delete the old USB stack. The new stack has settled in and has all the
drivers/functionality and then some.

fix legacy usb configuration

Update paths for ehci_ixp4xx.c in the old and new stacks.

Add support for the StrataFlash on 2348 boards:
o add bus shim for cfi driver
o add static mapping for CS0 (we map all 16M as the cfi driver doesn't
support demand mapping)

Note this needs some tweaking to work for 2358 boards which is why the
CAMBRIA config is not touched.

move IXP4XX EHCI bus shim to the usb directory and rename

Merge support for Gateworks Cambria boards:
o add support for IXP435 cpu's (e.g. 64 irq's)
o add support for Cambria-specific devices: npe, led's (front panel and
octal latch), ehci, mcu, ide cf
o redo memory mapping for xscale/ixp4xx boards: previously memory
was assumed aliased to 0x10000000 but this appears to be true only
for ixp425 systems and breaks operation on others; rework so memory
is assumed to start at 0
o rework NPE configuration support to use NPE id's instead of port #'s;
these changes also rename the associated MAC's to follow the NPE's
they are attached to
o update npe firmware to latest rev (same license) and update default fw
imageid's to match; in particular this adds NPE-A and crypto support
o re-style NPE fw handling code and add a console msg identifying the
attributes of the loaded fw
o fix numerous problems with handling failures during npe setup
o fix npe rx q setup; need to spin waiting for mailbox responses during
early boot stages as qmgr interrupts are not delivered; this fixes
the problem where all 8 traffic classifications were not tied to the
rx q (and eliminates the console msg "remember to fix rx q setup")
o add DELAY to npe MII wait logic for IXP435
o strip down builtin phys->virt address translation table in resource
handling to just those resources that require it and add a console msg
to alert people when this (kludge) table needs to be extended
o purge a bunch of dead netbsd-ism's
o cleanup avila led driver
o add Cambria support to boot2 and rework code for better multi-board support

Notes:
1. NPE-A doesn't work and causes NPE-C to stop working; it is disabled
in the hints
2. USB isn't working yet; controller communicates ok but device
discovery fails
3. Cambria support must be configured separately from IXP425 boards;
multi-board support is TBD

Sponsored by: Hobnob, Gateworks (board donation)
Reviewed by: imp

Refactor certain ARM bus space methods: instead of having multiple copies of
the same code introduce sys/arm/arm/bus_space_generic.c for a shared set of
routines.

Reviewed by: sam
Approved by: cognet (mentor)

Ok I hope I got it right this time.
After discussion with Sam, switch back to use firmware(9) instead of
having the firmware in hex format.
Put the binary firmware uuencoded into sys/contrib/dev/npe, and slap a
LICENSE file, as found on the Intel website.

Approved by: re (blanket), mux (mentor)
MFC After: 1 week

Now that Intel changed the license for the NPE firmware, import it directly
hexed into our tree, instead of requiring the user to download it.

Approved by: re (blanket)
MFC after: 1 week

Handle a missing NPE firmware file better; if it's missing print a
(somewhat) meaningful message and terminate the build. It'd be
nice to print a proper URL from which to fetch the file but that
seems problematic. Leave a suggested starting point in this file
(TBD: add it to the man page).

Submitted by: ru

Gateworks Avila board support:
o ixp425 support
o NPE network driver (requires Intel microcode)
o h/w qmgr support
o True IDE compact flash over expansion bus
o pci (ath and hifn795x parts tested)
o xscale watchdog timer
o ds1672 RTC on i2c bus
o ad7418 voltage + temp monitoring on i2c bus
o uart

Work done together with cognet, kevlo, and jmg. Parts of
the ixp425 support obtaine/derived from netbsd.

Reviewed by: cognet, imp
MFC after: 1 month