Copy head (r256279) to stable/10 as part of the 10.0-RELEASE cycle.

Approved by: re (implicit)
Sponsored by: The FreeBSD Foundation

- Merge the *_SET macros from fire(4) which generally print out the
register changes when compiled with SCHIZO_DEBUG and take advantage
of them.
- Add support for the XMITS Fireplane/Safari to PCI-X bridges. I tought
I'd need this for a Sun Fire 3800, which then turned out to not being
equipped with such a bridge though. The support for these should be
complete but given that it hasn't actually been tested probing is
disabled for now.
This required a way to alter the XMITS configuration in case a PCI-X
device is found further down the device tree so the sparc64 specific
ofw_pci kobj was revived with a ofw_pci_setup_device method, which is
called by the ofw_pcibus code for every device added.
- A closer inspection of the OpenSolaris code indicates that consistent
DMA flushing/syncing as well as the block store workaround should be
applied with every BUS_DMASYNC_POSTREAD instead of in a wrapper around
interrupt handlers for devices behind PCI-PCI bridges only as suggested
by the documentation (code for the latter actually exists in OpenSolaris
but is disabled by default), which also makes more sense.
- Add a workaround for Casinni/Skyhawk combinations. Chances are that
this solves the crashes seen when using the the on-board Casinni NICs
of Sun Fire V480 equipped with centerplanes other than 501-6780 or
501-6790. This also takes advantage of the ofw_pci_setup_device method.
- Mark some unused parameters as such.

Resurrect ofw_pci_if.m from r178578.

On sparc64 machines with multiple host-PCI-bridges these bridges
have separate configuration spaces so by definition they implement
different PCI domains. Thus change psycho(4) to use PCI domains
instead of reenumerating all PCI busses so they have globally unique
bus numbers and drop support for reenumerating busses in the OFW PCI
code.
According to CVS history reenumeration was also required in order to
get some E450 to boot but given that no other open source kernel
changes the PCI bus numbers assigned by the firmware I believe the
real problem was that the old code used the bus number as the device
number for the PCI busses and unlike most of the other machines the
firmwares of the problematic ones don't use disjoint PCI bus numbers
across the host-PCI-bridges.

MFC after: 1 month

- Move ofw_pci_alloc_busno() to the ofw_pci KOBJ interface,
allowing the driver for the host-PCI-bridge to indicate that
reenumeration of the PCI busses isn't supported by returning
-1 instead of a valid PCI bus number. This is needed in order
support both Tomatillo, which don't support reenumeration and
thus are apparently intended to be used for independently
numbered PCI domains only, and Psycho bridges, whose busses
need to be reenumerated on at least some E450, without the
#ifndef currently used for sun4v in order to support multiple
independently PCI domains. The actual allocation/incrementation
of the PCI bus numbers is now done in psycho(4), though it
no longer establish a mapping between bus numbers and device
nodes like ofw_pci_alloc_busno() did as that functionality
wasn't used (but can easily brought back if really needed).
The now no longer used sys/sparc64/pci/ofw_pci.c is also
removed from sys/conf/files.sun4v as ofw_pci_alloc_busno()
wasn't used there in the first place.
- In ofw_pci_default_{adjust_busrange,intr_pending}() sanity
check that the device has a parent before passing it on.
- Make psycho_softcs static to sys/sparc64/pci/psycho.c as
it's not used outside of that module.
- In sys/sparc64/pci/ofw_pcib_subr.c remove the superfluous
inclusion of opt_global.h and correct the debug output for
adjusting the subordinate bus number.

Remove the compat shims for the ISA old-stlye in{b,w,l}()/out{b,w,l}()
and friends along with all hacks required to implement them. None of
the drivers currently built (as part of GENERIC, LINT or modules) on
sparc64 or sun4v and none of those we might want to use there in
future uses them, AFAICT there actually never was a driver hooked up
to the sparc64 or sun4v build that correctly used these functions
(and it looks like that due to a bug read{b,w,l}()/write{b,w,l}() and
the other functions working on a memory handle never actually worked on
sun4v). All they ever were good for on sparc64 and sun4v was erroneously
dragging in dependencies on isa(4) in drivers like f.e. dpt(4), si(4)
and syscons(4) in source files that supposedly were bus-neutral and
hiding issues with drivers like f.e. ng_bt3c(4) that used these
functions with busses other than isa(4) and therefore couldn't work on
these platforms.

/* -> /*- for license, minor formatting changes

- Introduce an ofw_bus kobj-interface for retrieving the OFW node and a
subset ("compatible", "device_type", "model" and "name") of the standard
properties in drivers for devices on Open Firmware supported busses. The
standard properties "reg", "interrupts" und "address" are not covered by
this interface because they are only of interest in the respective bridge
code. There's a remaining standard property "status" which is unclear how
to support properly but which also isn't used in FreeBSD at present.
This ofw_bus kobj-interface allows to replace the various (ebus_get_node(),
ofw_pci_get_node(), etc.) and partially inconsistent (central_get_type()
vs. sbus_get_device_type(), etc.) existing IVAR ones with a common one.
This in turn allows to simplify and remove code-duplication in drivers for
devices that can hang off of more than one OFW supported bus.
- Convert the sparc64 Central, EBus, FHC, PCI and SBus bus drivers and the
drivers for their children to use the ofw_bus kobj-interface. The IVAR-
interfaces of the Central, EBus and FHC are entirely replaced by this. The
PCI bus driver used its own kobj-interface and now also uses the ofw_bus
one. The IVARs special to the SBus, e.g. for retrieving the burst size,
remain.
Beware: this causes an ABI-breakage for modules of drivers which used the
IVAR-interfaces, i.e. esp(4), hme(4), isp(4) and uart(4), which need to be
recompiled.
The style-inconsistencies introduced in some of the bus drivers will be
fixed by tmm@ in a generic clean-up of the respective drivers later (he
requested to add the changes in the "new" style).
- Convert the powerpc MacIO bus driver and the drivers for its children to
use the ofw_bus kobj-interface. This invloves removing the IVARs related
to the "reg" property which were unused and a leftover from the NetBSD
origini of the code. There's no ABI-breakage caused by this because none
of these driver are currently built as modules.
There are other powerpc bus drivers which can be converted to the ofw_bus
kobj-interface, e.g. the PCI bus driver, which should be done together
with converting powerpc to use the OFW PCI code from sparc64.
- Make the SBus and FHC front-end of zs(4) and the sparc64 eeprom(4) take
advantage of the ofw_bus kobj-interface and simplify them a bit.

Reviewed by: grehan, tmm
Approved by: re (scottl)
Discussed with: tmm
Tested with: Sun AX1105, AXe, Ultra 2, Ultra 60; PPC cross-build on i386

- Remove the old sparc64 OFW PCI code (as opposed to the former
"options OFW_NEWPCI").
This is a bit overdue, the new sparc64 OFW PCI code which is
meant to replace the old one is in place for 10 months and
enabled by default in GENERIC for 8 months. FreeBSD 5.2 and
5.2.1 also shipped with the new code enabled by default.
- Some minor clean-up, e.g. remove functions that encapsulated
the #ifdefs for OFW_NEWPCI, remove unused resp. no longer
required includes, etc.

Approved by: tmm, no objections on freebsd-sparc64

Add the new sparc64 OFW PCI framework, conditional on options OFW_NEWPCI
for now. It introduces a OFW PCI bus driver and a generic OFW PCI-PCI
bridge driver. By utilizing these, the PCI handling is much more elegant
now.

The advantages of the new approach are:
- Device enumeration should hopefully be more like on Solaris now,
so unit numbers should match what's printed on the box more
closely.
- Real interrupt routing is implemented now, so cardbus bridges
etc. have at least a chance to work.
- The quirk tables are gone and have been replaced by (hopefully
sufficient) heuristics.
- Much cleaner code.

There was also a report that previously bogus interrupt assignments
are fixed now, which can be attributed to the new heuristics.

A pitfall, and the reason why this is not the default yet, is that
it changes device enumeration, as mentioned above, which can make
it necessary to change the system configuration if more than one
unit of a device type is present (on a system with two hme cars,
for example, it is possible that hme0 becomes hme1 and vice versa
after enabling the option). Systems with multiple disk controllers
may need to be booted into single user (and require manual specification
of the root file system on boot) to adjust the fstab.
Nevertheless, I would like to encourage users to use this option,
so that it can be made the default soon.

In detail, the changes are:
- Introduce an OFW PCI bus driver; it inherits most methods from the
generic PCI bus driver, but uses the firmware for enumeration,
performs additional initialization for devices and firmware-specific
interrupt routing. It also implements an OFW-specific method to allow
child devices to get their firmware nodes.
- Introduce an OFW PCI-PCI bridge driver; again, it inherits most
of the generic PCI-PCI bridge driver; it has it's own method for
interrupt routing, as well as some sparc64-specific methods (one to
get the node again, and one to adjust the bridge bus range, since
we need to reenumerate all PCI buses).
- Convert the apb driver to the new way of handling things.
- Provide a common framework for OFW bridge drivers, used be the two
drivers above.
- Provide a small common framework for interrupt routing (for all
bridge types).
- Convert the psycho driver to the new framework; this gets rid of a
bunch of old kludges in pci_read_config(), and the whole
preinitialization (ofw_pci_init()).
- Convert the ISA MD part and the EBus driver to the new way
interrupts and nodes are handled.
- Introduce types for firmware interrupt properties.
- Rename the old sparcbus_if to ofw_pci_if by repo copy (it is only
required for PCI), and move it to a more correct location (new
support methodsx were also added, and an old one was deprecated).
- Fix a bunch of minor bugs, perform some cleanups.

In some cases, I introduced some minor code duplication to keep the
new code clean, in hopes that the old code will be unifdef'ed soon.

Reviewed in part by: imp
Tested by: jake, Marius Strobl <marius@alchemy.franken.de>,
Sergey Mokryshev <mokr@mokr.net>,
Chris Jackman <cjackNOSPAM@klatsch.org>
Info on u30 firmware provided by: kris

Fix interrupt assignment for non-builtin PCI devices on e450s.

This machine uses a non-standard scheme to specify the interrupts to
be assigned for devices in PCI slots; instead of giving the INO
or full interrupt number (which is done for the other devices in this
box), the firmware interrupt properties contain intpin numbers, which
have to be swizzled as usual on PCI-PCI bridges; however, the PCI host
bridge nodes have no interrupt map, so we need to guess the
correct INO by slot number of the device or the closest PCI-PCI
bridge leading to it, and the intpin.

To do this, this fix makes the following changes:
- Add a newbus method for sparc64 PCI host bridges to guess
the INO, and glue code in ofw_pci_orb_callback() to invoke it based
on a new quirk entry. The guessing is only done for interrupt numbers
too low to contain any IGN found on e450s.
- Create another new quirk entry was created to prevent mapping of EBus
interrupts at PCI level; the e450 has full INOs in the interrupt
properties of EBus devices, so trying to remap them could cause
problems.
- Set both quirk entries for e450s; remove the no-swizzle entry.
- Determine the psycho half (bus A or B) a driver instance manages
in psycho_attach()
- Implement the new guessing method for psycho, using the slot number,
psycho half and property value (intpin).

Thanks go to the testers, especially Brian Denehy, who tested many kernels
for me until I had found the right workaround.

Tested by: Brian Denehy <B.Denehy@90east.com>, jake, fenner,
Marius Strobl <marius@alchemy.franken.de>,
Marian Dobre <mari@onix.ro>
Approved by: re (scottl)

Add a file forgotten in the previous commit (a kobj interface that
defines methods that need to be implemented by sparc64 host bridge drivers).