MFC r276803, r276808:

Add accessors for the ARM CP15 performance monitor registers.
Move the inclusion of cpu-v6.h inside the #ifdef _KERNEL block.

MFC r266083, r267597:

Give suitably-endowed ARMs a register similar to the x86 TSC register.

MFC r261643, r261646, r261648, r261649, r261651, r261656, r261657, r261663,
r261676, r261677, r261698, r261778

Consolidate code related to setting up physical memory configuration into
a new physmem.c file.

Replace compile-time constant KERNPHYSADDR with abp_physaddr

Calculate the kernel's load address from the PC in the elf / gzip
trampoline instead of relying on KERNPHYSADDR as a compile-time constant.

It turns out a global variable is the only straightforward way to
communicate the kernel's physical load address from where it's known in
initarm() into cpu_mp_start() which is called from non-arm code and
takes no parameters.

Remove the now unused MMU_INIT macro.

Use vm_paddr_t, not vm_offset_t, when dealing with physical addresses.

No need to set physmem in each initarm() instance anymore, it's handled
in common code now.

Pass the pagetable used from locore.S to initarm to allow it to map data
in as required.

Fix the physmem exclude-region clipping logic for the edge-trim case.

Add some extra debugging output when DEBUG is defined.

Update legacy platforms to use new arm_physmem helper routines.

MFC r261423, r261424, r261516, r261513, r261562, r261563, r261564, r261565,
r261596, r261606

Add the imx sdhci controller.

Move Open Firmware device root on PowerPC, ARM, and MIPS systems to
a sub-node of nexus (ofwbus) rather than direct attach under nexus. This
fixes FDT on x86 and will make coexistence with ACPI on ARM systems easier.
SPARC is unchanged.

Add the missing ')' at end of sentence. Reword it to use a more common idiom.

Pass the kernel physical address to initarm through the boot param struct.

Make functions only used in vfp.c static, and remove vfp_enable.

Fix __syscall on armeb EABI. As it returns a 64-bit value it needs to
place 32-bit data in r1, not r0. 64-bit data is already packed correctly.

Use abp_physaddr for the physical address over KERNPHYSADDR. This helps us
remove the need to load the kernel at a fixed address.

Remove references to PHYSADDR where it's used only in debugging output.

Dynamically generate the page table. This will allow us to detect the
physical address we are loaded at to change the mapping.

MFC r257199, r257200, r257217:

Remove all #include <machine/pmap.h> from arm code. It's already
included by vm/pmap.h, which is a prerequisite for arm/machine/pmap.h
so there's no reason to ever include it directly.

Remove #include <machine/frame.h> from all the arm code that doesn't
really need it. That would be almost everywhere it was included. Add
it in a couple files that really do need it and were previously getting
it by accident via another header.

Remove the last dregs of trapframe_t. It turns out only arm was using
this type, so remove it to make arm code more consistant with other
platforms.

MFC r276803, r276808:

Add accessors for the ARM CP15 performance monitor registers.
Move the inclusion of cpu-v6.h inside the #ifdef _KERNEL block.

MFC r266083, r267597:

Give suitably-endowed ARMs a register similar to the x86 TSC register.

MFC r261643, r261646, r261648, r261649, r261651, r261656, r261657, r261663,
r261676, r261677, r261698, r261778

Consolidate code related to setting up physical memory configuration into
a new physmem.c file.

Replace compile-time constant KERNPHYSADDR with abp_physaddr

Calculate the kernel's load address from the PC in the elf / gzip
trampoline instead of relying on KERNPHYSADDR as a compile-time constant.

It turns out a global variable is the only straightforward way to
communicate the kernel's physical load address from where it's known in
initarm() into cpu_mp_start() which is called from non-arm code and
takes no parameters.

Remove the now unused MMU_INIT macro.

Use vm_paddr_t, not vm_offset_t, when dealing with physical addresses.

No need to set physmem in each initarm() instance anymore, it's handled
in common code now.

Pass the pagetable used from locore.S to initarm to allow it to map data
in as required.

Fix the physmem exclude-region clipping logic for the edge-trim case.

Add some extra debugging output when DEBUG is defined.

Update legacy platforms to use new arm_physmem helper routines.

MFC r261423, r261424, r261516, r261513, r261562, r261563, r261564, r261565,
r261596, r261606

Add the imx sdhci controller.

Move Open Firmware device root on PowerPC, ARM, and MIPS systems to
a sub-node of nexus (ofwbus) rather than direct attach under nexus. This
fixes FDT on x86 and will make coexistence with ACPI on ARM systems easier.
SPARC is unchanged.

Add the missing ')' at end of sentence. Reword it to use a more common idiom.

Pass the kernel physical address to initarm through the boot param struct.

Make functions only used in vfp.c static, and remove vfp_enable.

Fix __syscall on armeb EABI. As it returns a 64-bit value it needs to
place 32-bit data in r1, not r0. 64-bit data is already packed correctly.

Use abp_physaddr for the physical address over KERNPHYSADDR. This helps us
remove the need to load the kernel at a fixed address.

Remove references to PHYSADDR where it's used only in debugging output.

Dynamically generate the page table. This will allow us to detect the
physical address we are loaded at to change the mapping.

MFC r257199, r257200, r257217:

Remove all #include <machine/pmap.h> from arm code. It's already
included by vm/pmap.h, which is a prerequisite for arm/machine/pmap.h
so there's no reason to ever include it directly.

Remove #include <machine/frame.h> from all the arm code that doesn't
really need it. That would be almost everywhere it was included. Add
it in a couple files that really do need it and were previously getting
it by accident via another header.

Remove the last dregs of trapframe_t. It turns out only arm was using
this type, so remove it to make arm code more consistant with other
platforms.