1// SPDX-License-Identifier: GPL-2.0+ 2/* 3 * Copyright (C) 2014 Wandboard 4 * Author: Tungyi Lin <tungyilin1127@gmail.com> 5 * Richard Hu <hakahu@gmail.com> 6 */ 7 8#include <config.h> 9#include <init.h> 10#include <asm/arch/clock.h> 11#include <asm/arch/imx-regs.h> 12#include <asm/arch/iomux.h> 13#include <asm/arch/mx6-pins.h> 14#include <linux/delay.h> 15#include <linux/errno.h> 16#include <asm/gpio.h> 17#include <asm/mach-imx/iomux-v3.h> 18#include <asm/mach-imx/video.h> 19#include <mmc.h> 20#include <fsl_esdhc_imx.h> 21#include <asm/arch/crm_regs.h> 22#include <asm/io.h> 23#include <asm/arch/sys_proto.h> 24#include <spl.h> 25 26#include <asm/arch/mx6-ddr.h> 27/* 28 * Driving strength: 29 * 0x30 == 40 Ohm 30 * 0x28 == 48 Ohm 31 */ 32 33#define IMX6DQ_DRIVE_STRENGTH 0x30 34#define IMX6SDL_DRIVE_STRENGTH 0x28 35#define IMX6QP_DRIVE_STRENGTH 0x28 36 37/* configure MX6Q/DUAL mmdc DDR io registers */ 38static struct mx6dq_iomux_ddr_regs mx6dq_ddr_ioregs = { 39 .dram_sdclk_0 = IMX6DQ_DRIVE_STRENGTH, 40 .dram_sdclk_1 = IMX6DQ_DRIVE_STRENGTH, 41 .dram_cas = IMX6DQ_DRIVE_STRENGTH, 42 .dram_ras = IMX6DQ_DRIVE_STRENGTH, 43 .dram_reset = IMX6DQ_DRIVE_STRENGTH, 44 .dram_sdcke0 = IMX6DQ_DRIVE_STRENGTH, 45 .dram_sdcke1 = IMX6DQ_DRIVE_STRENGTH, 46 .dram_sdba2 = 0x00000000, 47 .dram_sdodt0 = IMX6DQ_DRIVE_STRENGTH, 48 .dram_sdodt1 = IMX6DQ_DRIVE_STRENGTH, 49 .dram_sdqs0 = IMX6DQ_DRIVE_STRENGTH, 50 .dram_sdqs1 = IMX6DQ_DRIVE_STRENGTH, 51 .dram_sdqs2 = IMX6DQ_DRIVE_STRENGTH, 52 .dram_sdqs3 = IMX6DQ_DRIVE_STRENGTH, 53 .dram_sdqs4 = IMX6DQ_DRIVE_STRENGTH, 54 .dram_sdqs5 = IMX6DQ_DRIVE_STRENGTH, 55 .dram_sdqs6 = IMX6DQ_DRIVE_STRENGTH, 56 .dram_sdqs7 = IMX6DQ_DRIVE_STRENGTH, 57 .dram_dqm0 = IMX6DQ_DRIVE_STRENGTH, 58 .dram_dqm1 = IMX6DQ_DRIVE_STRENGTH, 59 .dram_dqm2 = IMX6DQ_DRIVE_STRENGTH, 60 .dram_dqm3 = IMX6DQ_DRIVE_STRENGTH, 61 .dram_dqm4 = IMX6DQ_DRIVE_STRENGTH, 62 .dram_dqm5 = IMX6DQ_DRIVE_STRENGTH, 63 .dram_dqm6 = IMX6DQ_DRIVE_STRENGTH, 64 .dram_dqm7 = IMX6DQ_DRIVE_STRENGTH, 65}; 66 67/* configure MX6QP mmdc DDR io registers */ 68static struct mx6dq_iomux_ddr_regs mx6qp_ddr_ioregs = { 69 .dram_sdclk_0 = IMX6QP_DRIVE_STRENGTH, 70 .dram_sdclk_1 = IMX6QP_DRIVE_STRENGTH, 71 .dram_cas = IMX6QP_DRIVE_STRENGTH, 72 .dram_ras = IMX6QP_DRIVE_STRENGTH, 73 .dram_reset = IMX6QP_DRIVE_STRENGTH, 74 .dram_sdcke0 = IMX6QP_DRIVE_STRENGTH, 75 .dram_sdcke1 = IMX6QP_DRIVE_STRENGTH, 76 .dram_sdba2 = 0x00000000, 77 .dram_sdodt0 = IMX6QP_DRIVE_STRENGTH, 78 .dram_sdodt1 = IMX6QP_DRIVE_STRENGTH, 79 .dram_sdqs0 = IMX6QP_DRIVE_STRENGTH, 80 .dram_sdqs1 = IMX6QP_DRIVE_STRENGTH, 81 .dram_sdqs2 = IMX6QP_DRIVE_STRENGTH, 82 .dram_sdqs3 = IMX6QP_DRIVE_STRENGTH, 83 .dram_sdqs4 = IMX6QP_DRIVE_STRENGTH, 84 .dram_sdqs5 = IMX6QP_DRIVE_STRENGTH, 85 .dram_sdqs6 = IMX6QP_DRIVE_STRENGTH, 86 .dram_sdqs7 = IMX6QP_DRIVE_STRENGTH, 87 .dram_dqm0 = IMX6QP_DRIVE_STRENGTH, 88 .dram_dqm1 = IMX6QP_DRIVE_STRENGTH, 89 .dram_dqm2 = IMX6QP_DRIVE_STRENGTH, 90 .dram_dqm3 = IMX6QP_DRIVE_STRENGTH, 91 .dram_dqm4 = IMX6QP_DRIVE_STRENGTH, 92 .dram_dqm5 = IMX6QP_DRIVE_STRENGTH, 93 .dram_dqm6 = IMX6QP_DRIVE_STRENGTH, 94 .dram_dqm7 = IMX6QP_DRIVE_STRENGTH, 95}; 96 97/* configure MX6Q/DUAL mmdc GRP io registers */ 98static struct mx6dq_iomux_grp_regs mx6dq_grp_ioregs = { 99 .grp_ddr_type = 0x000c0000, 100 .grp_ddrmode_ctl = 0x00020000, 101 .grp_ddrpke = 0x00000000, 102 .grp_addds = IMX6DQ_DRIVE_STRENGTH, 103 .grp_ctlds = IMX6DQ_DRIVE_STRENGTH, 104 .grp_ddrmode = 0x00020000, 105 .grp_b0ds = IMX6DQ_DRIVE_STRENGTH, 106 .grp_b1ds = IMX6DQ_DRIVE_STRENGTH, 107 .grp_b2ds = IMX6DQ_DRIVE_STRENGTH, 108 .grp_b3ds = IMX6DQ_DRIVE_STRENGTH, 109 .grp_b4ds = IMX6DQ_DRIVE_STRENGTH, 110 .grp_b5ds = IMX6DQ_DRIVE_STRENGTH, 111 .grp_b6ds = IMX6DQ_DRIVE_STRENGTH, 112 .grp_b7ds = IMX6DQ_DRIVE_STRENGTH, 113}; 114 115/* configure MX6QP mmdc GRP io registers */ 116static struct mx6dq_iomux_grp_regs mx6qp_grp_ioregs = { 117 .grp_ddr_type = 0x000c0000, 118 .grp_ddrmode_ctl = 0x00020000, 119 .grp_ddrpke = 0x00000000, 120 .grp_addds = IMX6QP_DRIVE_STRENGTH, 121 .grp_ctlds = IMX6QP_DRIVE_STRENGTH, 122 .grp_ddrmode = 0x00020000, 123 .grp_b0ds = IMX6QP_DRIVE_STRENGTH, 124 .grp_b1ds = IMX6QP_DRIVE_STRENGTH, 125 .grp_b2ds = IMX6QP_DRIVE_STRENGTH, 126 .grp_b3ds = IMX6QP_DRIVE_STRENGTH, 127 .grp_b4ds = IMX6QP_DRIVE_STRENGTH, 128 .grp_b5ds = IMX6QP_DRIVE_STRENGTH, 129 .grp_b6ds = IMX6QP_DRIVE_STRENGTH, 130 .grp_b7ds = IMX6QP_DRIVE_STRENGTH, 131}; 132 133/* configure MX6SOLO/DUALLITE mmdc DDR io registers */ 134struct mx6sdl_iomux_ddr_regs mx6sdl_ddr_ioregs = { 135 .dram_sdclk_0 = IMX6SDL_DRIVE_STRENGTH, 136 .dram_sdclk_1 = IMX6SDL_DRIVE_STRENGTH, 137 .dram_cas = IMX6SDL_DRIVE_STRENGTH, 138 .dram_ras = IMX6SDL_DRIVE_STRENGTH, 139 .dram_reset = IMX6SDL_DRIVE_STRENGTH, 140 .dram_sdcke0 = IMX6SDL_DRIVE_STRENGTH, 141 .dram_sdcke1 = IMX6SDL_DRIVE_STRENGTH, 142 .dram_sdba2 = 0x00000000, 143 .dram_sdodt0 = IMX6SDL_DRIVE_STRENGTH, 144 .dram_sdodt1 = IMX6SDL_DRIVE_STRENGTH, 145 .dram_sdqs0 = IMX6SDL_DRIVE_STRENGTH, 146 .dram_sdqs1 = IMX6SDL_DRIVE_STRENGTH, 147 .dram_sdqs2 = IMX6SDL_DRIVE_STRENGTH, 148 .dram_sdqs3 = IMX6SDL_DRIVE_STRENGTH, 149 .dram_sdqs4 = IMX6SDL_DRIVE_STRENGTH, 150 .dram_sdqs5 = IMX6SDL_DRIVE_STRENGTH, 151 .dram_sdqs6 = IMX6SDL_DRIVE_STRENGTH, 152 .dram_sdqs7 = IMX6SDL_DRIVE_STRENGTH, 153 .dram_dqm0 = IMX6SDL_DRIVE_STRENGTH, 154 .dram_dqm1 = IMX6SDL_DRIVE_STRENGTH, 155 .dram_dqm2 = IMX6SDL_DRIVE_STRENGTH, 156 .dram_dqm3 = IMX6SDL_DRIVE_STRENGTH, 157 .dram_dqm4 = IMX6SDL_DRIVE_STRENGTH, 158 .dram_dqm5 = IMX6SDL_DRIVE_STRENGTH, 159 .dram_dqm6 = IMX6SDL_DRIVE_STRENGTH, 160 .dram_dqm7 = IMX6SDL_DRIVE_STRENGTH, 161}; 162 163/* configure MX6SOLO/DUALLITE mmdc GRP io registers */ 164struct mx6sdl_iomux_grp_regs mx6sdl_grp_ioregs = { 165 .grp_ddr_type = 0x000c0000, 166 .grp_ddrmode_ctl = 0x00020000, 167 .grp_ddrpke = 0x00000000, 168 .grp_addds = IMX6SDL_DRIVE_STRENGTH, 169 .grp_ctlds = IMX6SDL_DRIVE_STRENGTH, 170 .grp_ddrmode = 0x00020000, 171 .grp_b0ds = IMX6SDL_DRIVE_STRENGTH, 172 .grp_b1ds = IMX6SDL_DRIVE_STRENGTH, 173 .grp_b2ds = IMX6SDL_DRIVE_STRENGTH, 174 .grp_b3ds = IMX6SDL_DRIVE_STRENGTH, 175 .grp_b4ds = IMX6SDL_DRIVE_STRENGTH, 176 .grp_b5ds = IMX6SDL_DRIVE_STRENGTH, 177 .grp_b6ds = IMX6SDL_DRIVE_STRENGTH, 178 .grp_b7ds = IMX6SDL_DRIVE_STRENGTH, 179}; 180 181/* H5T04G63AFR-PB */ 182static struct mx6_ddr3_cfg h5t04g63afr = { 183 .mem_speed = 1600, 184 .density = 4, 185 .width = 16, 186 .banks = 8, 187 .rowaddr = 15, 188 .coladdr = 10, 189 .pagesz = 2, 190 .trcd = 1375, 191 .trcmin = 4875, 192 .trasmin = 3500, 193}; 194 195/* H5TQ2G63DFR-H9 */ 196static struct mx6_ddr3_cfg h5tq2g63dfr = { 197 .mem_speed = 1333, 198 .density = 2, 199 .width = 16, 200 .banks = 8, 201 .rowaddr = 14, 202 .coladdr = 10, 203 .pagesz = 2, 204 .trcd = 1350, 205 .trcmin = 4950, 206 .trasmin = 3600, 207}; 208 209static struct mx6_mmdc_calibration mx6q_2g_mmdc_calib = { 210 .p0_mpwldectrl0 = 0x001f001f, 211 .p0_mpwldectrl1 = 0x001f001f, 212 .p1_mpwldectrl0 = 0x001f001f, 213 .p1_mpwldectrl1 = 0x001f001f, 214 .p0_mpdgctrl0 = 0x4301030d, 215 .p0_mpdgctrl1 = 0x03020277, 216 .p1_mpdgctrl0 = 0x4300030a, 217 .p1_mpdgctrl1 = 0x02780248, 218 .p0_mprddlctl = 0x4536393b, 219 .p1_mprddlctl = 0x36353441, 220 .p0_mpwrdlctl = 0x41414743, 221 .p1_mpwrdlctl = 0x462f453f, 222}; 223 224/* DDR 64bit 2GB */ 225static struct mx6_ddr_sysinfo mem_q = { 226 .dsize = 2, 227 .cs1_mirror = 0, 228 /* config for full 4GB range so that get_mem_size() works */ 229 .cs_density = 32, 230 .ncs = 1, 231 .bi_on = 1, 232 .rtt_nom = 1, 233 .rtt_wr = 0, 234 .ralat = 5, 235 .walat = 0, 236 .mif3_mode = 3, 237 .rst_to_cke = 0x23, 238 .sde_to_rst = 0x10, 239 .refsel = 1, /* Refresh cycles at 32KHz */ 240 .refr = 3, /* 4 refresh commands per refresh cycle */ 241}; 242 243static struct mx6_mmdc_calibration mx6dl_1g_mmdc_calib = { 244 .p0_mpwldectrl0 = 0x001f001f, 245 .p0_mpwldectrl1 = 0x001f001f, 246 .p1_mpwldectrl0 = 0x001f001f, 247 .p1_mpwldectrl1 = 0x001f001f, 248 .p0_mpdgctrl0 = 0x420e020e, 249 .p0_mpdgctrl1 = 0x02000200, 250 .p1_mpdgctrl0 = 0x42020202, 251 .p1_mpdgctrl1 = 0x01720172, 252 .p0_mprddlctl = 0x494c4f4c, 253 .p1_mprddlctl = 0x4a4c4c49, 254 .p0_mpwrdlctl = 0x3f3f3133, 255 .p1_mpwrdlctl = 0x39373f2e, 256}; 257 258static struct mx6_mmdc_calibration mx6s_512m_mmdc_calib = { 259 .p0_mpwldectrl0 = 0x0040003c, 260 .p0_mpwldectrl1 = 0x0032003e, 261 .p0_mpdgctrl0 = 0x42350231, 262 .p0_mpdgctrl1 = 0x021a0218, 263 .p0_mprddlctl = 0x4b4b4e49, 264 .p0_mpwrdlctl = 0x3f3f3035, 265}; 266 267/* DDR 64bit 1GB */ 268static struct mx6_ddr_sysinfo mem_dl = { 269 .dsize = 2, 270 .cs1_mirror = 0, 271 /* config for full 4GB range so that get_mem_size() works */ 272 .cs_density = 32, 273 .ncs = 1, 274 .bi_on = 1, 275 .rtt_nom = 1, 276 .rtt_wr = 0, 277 .ralat = 5, 278 .walat = 0, 279 .mif3_mode = 3, 280 .rst_to_cke = 0x23, 281 .sde_to_rst = 0x10, 282 .refsel = 1, /* Refresh cycles at 32KHz */ 283 .refr = 3, /* 4 refresh commands per refresh cycle */ 284}; 285 286/* DDR 32bit 512MB */ 287static struct mx6_ddr_sysinfo mem_s = { 288 .dsize = 1, 289 .cs1_mirror = 0, 290 /* config for full 4GB range so that get_mem_size() works */ 291 .cs_density = 32, 292 .ncs = 1, 293 .bi_on = 1, 294 .rtt_nom = 1, 295 .rtt_wr = 0, 296 .ralat = 5, 297 .walat = 0, 298 .mif3_mode = 3, 299 .rst_to_cke = 0x23, 300 .sde_to_rst = 0x10, 301 .refsel = 1, /* Refresh cycles at 32KHz */ 302 .refr = 3, /* 4 refresh commands per refresh cycle */ 303}; 304 305static void ccgr_init(void) 306{ 307 struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR; 308 309 writel(0x00C03F3F, &ccm->CCGR0); 310 writel(0x0030FC03, &ccm->CCGR1); 311 writel(0x0FFFC000, &ccm->CCGR2); 312 writel(0x3FF03000, &ccm->CCGR3); 313 writel(0x00FFF300, &ccm->CCGR4); 314 writel(0x0F0000C3, &ccm->CCGR5); 315 writel(0x000003FF, &ccm->CCGR6); 316} 317 318static void spl_dram_init_imx6qp_lpddr3(void) 319{ 320 /* MMDC0_MDSCR set the Configuration request bit during MMDC set up */ 321 writel(0x00008000, MMDC_P0_BASE_ADDR + 0x01c); 322 /* Calibrations - ZQ */ 323 writel(0xa1390003, MMDC_P0_BASE_ADDR + 0x800); 324 /* write leveling */ 325 writel(0x00060004, MMDC_P0_BASE_ADDR + 0x80c); 326 writel(0x000B0004, MMDC_P0_BASE_ADDR + 0x810); 327 writel(0x00000004, MMDC_P1_BASE_ADDR + 0x80c); 328 writel(0x00000000, MMDC_P1_BASE_ADDR + 0x810); 329 /* 330 * DQS gating, read delay, write delay calibration values 331 * based on calibration compare of 0x00ffff00 332 */ 333 writel(0x03040314, MMDC_P0_BASE_ADDR + 0x83c); 334 writel(0x03080300, MMDC_P0_BASE_ADDR + 0x840); 335 writel(0x03000310, MMDC_P1_BASE_ADDR + 0x83c); 336 writel(0x0268023C, MMDC_P1_BASE_ADDR + 0x840); 337 writel(0x4034363A, MMDC_P0_BASE_ADDR + 0x848); 338 writel(0x36302C3C, MMDC_P1_BASE_ADDR + 0x848); 339 writel(0x3E3E4046, MMDC_P0_BASE_ADDR + 0x850); 340 writel(0x483A4844, MMDC_P1_BASE_ADDR + 0x850); 341 writel(0x33333333, MMDC_P0_BASE_ADDR + 0x81c); 342 writel(0x33333333, MMDC_P0_BASE_ADDR + 0x820); 343 writel(0x33333333, MMDC_P0_BASE_ADDR + 0x824); 344 writel(0x33333333, MMDC_P0_BASE_ADDR + 0x828); 345 writel(0x33333333, MMDC_P1_BASE_ADDR + 0x81c); 346 writel(0x33333333, MMDC_P1_BASE_ADDR + 0x820); 347 writel(0x33333333, MMDC_P1_BASE_ADDR + 0x824); 348 writel(0x33333333, MMDC_P1_BASE_ADDR + 0x828); 349 writel(0x24912489, MMDC_P0_BASE_ADDR + 0x8c0); 350 writel(0x24914452, MMDC_P1_BASE_ADDR + 0x8c0); 351 writel(0x00000800, MMDC_P0_BASE_ADDR + 0x8b8); 352 writel(0x00000800, MMDC_P1_BASE_ADDR + 0x8b8); 353 /* MMDC init: in DDR3, 64-bit mode, only MMDC0 is initiated */ 354 writel(0x00020036, MMDC_P0_BASE_ADDR + 0x004); 355 writel(0x09444040, MMDC_P0_BASE_ADDR + 0x008); 356 writel(0x898E79A4, MMDC_P0_BASE_ADDR + 0x00c); 357 writel(0xDB538F64, MMDC_P0_BASE_ADDR + 0x010); 358 writel(0x01FF00DD, MMDC_P0_BASE_ADDR + 0x014); 359 writel(0x00011740, MMDC_P0_BASE_ADDR + 0x018); 360 writel(0x00008000, MMDC_P0_BASE_ADDR + 0x01c); 361 writel(0x000026D2, MMDC_P0_BASE_ADDR + 0x02c); 362 writel(0x008E1023, MMDC_P0_BASE_ADDR + 0x030); 363 writel(0x00000047, MMDC_P0_BASE_ADDR + 0x040); 364 writel(0x14420000, MMDC_P0_BASE_ADDR + 0x400); 365 writel(0x841A0000, MMDC_P0_BASE_ADDR + 0x000); 366 writel(0x00400c58, MMDC_P0_BASE_ADDR + 0x890); 367 /* add NOC DDR configuration */ 368 writel(0x00000000, NOC_DDR_BASE_ADDR + 0x008); 369 writel(0x2871C39B, NOC_DDR_BASE_ADDR + 0x00c); 370 writel(0x000005B4, NOC_DDR_BASE_ADDR + 0x038); 371 writel(0x00000040, NOC_DDR_BASE_ADDR + 0x014); 372 writel(0x00000020, NOC_DDR_BASE_ADDR + 0x028); 373 writel(0x00000020, NOC_DDR_BASE_ADDR + 0x02c); 374 writel(0x02088032, MMDC_P0_BASE_ADDR + 0x01c); 375 writel(0x00008033, MMDC_P0_BASE_ADDR + 0x01c); 376 writel(0x00048031, MMDC_P0_BASE_ADDR + 0x01c); 377 writel(0x19308030, MMDC_P0_BASE_ADDR + 0x01c); 378 writel(0x04008040, MMDC_P0_BASE_ADDR + 0x01c); 379 writel(0x00007800, MMDC_P0_BASE_ADDR + 0x020); 380 writel(0x00022227, MMDC_P0_BASE_ADDR + 0x818); 381 writel(0x00022227, MMDC_P1_BASE_ADDR + 0x818); 382 writel(0x00025576, MMDC_P0_BASE_ADDR + 0x004); 383 writel(0x00011006, MMDC_P0_BASE_ADDR + 0x404); 384 writel(0x00000000, MMDC_P0_BASE_ADDR + 0x01c); 385} 386 387static void spl_dram_init(void) 388{ 389 if (is_mx6dqp()) { 390 mx6dq_dram_iocfg(64, &mx6qp_ddr_ioregs, &mx6qp_grp_ioregs); 391 spl_dram_init_imx6qp_lpddr3(); 392 } else if (is_cpu_type(MXC_CPU_MX6SOLO)) { 393 mx6sdl_dram_iocfg(32, &mx6sdl_ddr_ioregs, &mx6sdl_grp_ioregs); 394 mx6_dram_cfg(&mem_s, &mx6s_512m_mmdc_calib, &h5tq2g63dfr); 395 } else if (is_cpu_type(MXC_CPU_MX6DL)) { 396 mx6sdl_dram_iocfg(64, &mx6sdl_ddr_ioregs, &mx6sdl_grp_ioregs); 397 mx6_dram_cfg(&mem_dl, &mx6dl_1g_mmdc_calib, &h5tq2g63dfr); 398 } else if (is_cpu_type(MXC_CPU_MX6Q)) { 399 mx6dq_dram_iocfg(64, &mx6dq_ddr_ioregs, &mx6dq_grp_ioregs); 400 mx6_dram_cfg(&mem_q, &mx6q_2g_mmdc_calib, &h5t04g63afr); 401 } 402 403 udelay(100); 404} 405 406void board_init_f(ulong dummy) 407{ 408 ccgr_init(); 409 410 /* setup AIPS and disable watchdog */ 411 arch_cpu_init(); 412 413 gpr_init(); 414 415 /* iomux */ 416 board_early_init_f(); 417 418 /* setup GP timer */ 419 timer_init(); 420 421 /* UART clocks enabled and gd valid - init serial console */ 422 preloader_console_init(); 423 424 /* DDR initialization */ 425 spl_dram_init(); 426} 427 428#define USDHC1_CD_GPIO IMX_GPIO_NR(1, 2) 429#define USDHC3_CD_GPIO IMX_GPIO_NR(3, 9) 430 431#define USDHC_PAD_CTRL (PAD_CTL_PUS_47K_UP | \ 432 PAD_CTL_SPEED_LOW | PAD_CTL_DSE_80ohm | \ 433 PAD_CTL_SRE_FAST | PAD_CTL_HYS) 434 435static struct fsl_esdhc_cfg usdhc_cfg[2] = { 436 {USDHC3_BASE_ADDR}, 437 {USDHC1_BASE_ADDR}, 438}; 439 440static iomux_v3_cfg_t const usdhc1_pads[] = { 441 IOMUX_PADS(PAD_SD1_CLK__SD1_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL)), 442 IOMUX_PADS(PAD_SD1_CMD__SD1_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL)), 443 IOMUX_PADS(PAD_SD1_DAT0__SD1_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL)), 444 IOMUX_PADS(PAD_SD1_DAT1__SD1_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL)), 445 IOMUX_PADS(PAD_SD1_DAT2__SD1_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL)), 446 IOMUX_PADS(PAD_SD1_DAT3__SD1_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL)), 447 /* Carrier MicroSD Card Detect */ 448 IOMUX_PADS(PAD_GPIO_2__GPIO1_IO02 | MUX_PAD_CTRL(NO_PAD_CTRL)), 449}; 450 451static iomux_v3_cfg_t const usdhc3_pads[] = { 452 IOMUX_PADS(PAD_SD3_CLK__SD3_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL)), 453 IOMUX_PADS(PAD_SD3_CMD__SD3_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL)), 454 IOMUX_PADS(PAD_SD3_DAT0__SD3_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL)), 455 IOMUX_PADS(PAD_SD3_DAT1__SD3_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL)), 456 IOMUX_PADS(PAD_SD3_DAT2__SD3_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL)), 457 IOMUX_PADS(PAD_SD3_DAT3__SD3_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL)), 458 /* SOM MicroSD Card Detect */ 459 IOMUX_PADS(PAD_EIM_DA9__GPIO3_IO09 | MUX_PAD_CTRL(NO_PAD_CTRL)), 460}; 461 462int board_mmc_getcd(struct mmc *mmc) 463{ 464 struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv; 465 int ret = 0; 466 467 switch (cfg->esdhc_base) { 468 case USDHC1_BASE_ADDR: 469 ret = !gpio_get_value(USDHC1_CD_GPIO); 470 break; 471 case USDHC3_BASE_ADDR: 472 ret = !gpio_get_value(USDHC3_CD_GPIO); 473 break; 474 } 475 476 return ret; 477} 478 479int board_mmc_init(struct bd_info *bis) 480{ 481 int ret; 482 u32 index = 0; 483 484 /* 485 * Following map is done: 486 * (U-Boot device node) (Physical Port) 487 * mmc0 SOM MicroSD 488 * mmc1 Carrier board MicroSD 489 */ 490 for (index = 0; index < CFG_SYS_FSL_USDHC_NUM; ++index) { 491 switch (index) { 492 case 0: 493 SETUP_IOMUX_PADS(usdhc3_pads); 494 usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK); 495 usdhc_cfg[0].max_bus_width = 4; 496 gpio_direction_input(USDHC3_CD_GPIO); 497 break; 498 case 1: 499 SETUP_IOMUX_PADS(usdhc1_pads); 500 usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK); 501 usdhc_cfg[1].max_bus_width = 4; 502 gpio_direction_input(USDHC1_CD_GPIO); 503 break; 504 default: 505 printf("Warning: you configured more USDHC controllers" 506 "(%d) then supported by the board (%d)\n", 507 index + 1, CFG_SYS_FSL_USDHC_NUM); 508 return -EINVAL; 509 } 510 511 ret = fsl_esdhc_initialize(bis, &usdhc_cfg[index]); 512 if (ret) 513 return ret; 514 } 515 516 return 0; 517} 518