1# SPDX-License-Identifier: GPL-2.0+
2#
3# Copyright (C) 2015, Bin Meng <bmeng.cn@gmail.com>
4
5config INTEL_QUARK
6	bool
7	select HAVE_RMU
8	select ARCH_EARLY_INIT_R
9	select ARCH_MISC_INIT
10	select DM_EVENT
11	imply ENABLE_MRC_CACHE
12	imply ETH_DESIGNWARE
13	imply ICH_SPI
14	imply INTEL_ICH6_GPIO
15	imply MMC
16	imply MMC_PCI
17	imply MMC_SDHCI
18	imply MMC_SDHCI_SDMA
19	imply SPI_FLASH
20	imply SYS_NS16550
21	imply USB
22	imply USB_EHCI_HCD
23
24if INTEL_QUARK
25
26config HAVE_RMU
27	bool "Add a Remote Management Unit (RMU) binary"
28	help
29	  Select this option to add a Remote Management Unit (RMU) binary
30	  to the resulting U-Boot image. It is a data block (up to 64K) of
31	  machine-specific code which must be put in the flash for the RMU
32	  within the Quark SoC processor to access when powered up before
33	  system BIOS is executed.
34
35config RMU_FILE
36	string "Remote Management Unit (RMU) binary filename"
37	depends on HAVE_RMU
38	default "rmu.bin"
39	help
40	  The filename of the file to use as Remote Management Unit (RMU)
41	  binary in the board directory.
42
43config RMU_ADDR
44	hex "Remote Management Unit (RMU) binary location"
45	depends on HAVE_RMU
46	default 0xfff00000
47	help
48	  The location of the RMU binary is determined by a strap. It must be
49	  put in flash at a location matching the strap-determined base address.
50
51	  The default base address of 0xfff00000 indicates that the binary must
52	  be located at offset 0 from the beginning of a 1MB flash device.
53
54config HAVE_CMC
55	bool
56	default HAVE_RMU
57
58config CMC_FILE
59	string
60	depends on HAVE_CMC
61	default RMU_FILE
62
63config CMC_ADDR
64	hex
65	depends on HAVE_CMC
66	default RMU_ADDR
67
68config ESRAM_BASE
69	hex
70	default 0x80000000
71	help
72	  Embedded SRAM (eSRAM) memory-mapped base address.
73
74config PCIE_ECAM_BASE
75	hex
76	default 0xe0000000
77
78config RCBA_BASE
79	hex
80	default 0xfed1c000
81	help
82	  Root Complex register block memory-mapped base address.
83
84config ACPI_PM1_BASE
85	hex
86	default 0x1000
87	help
88	  ACPI Power Management 1 (PM1) i/o-mapped base address.
89	  This device is defined in ACPI specification, with 16 bytes in size.
90
91config ACPI_PBLK_BASE
92	hex
93	default 0x1010
94	help
95	  ACPI Processor Block (PBLK) i/o-mapped base address.
96	  This device is defined in ACPI specification, with 16 bytes in size.
97
98config SPI_DMA_BASE
99	hex
100	default 0x1020
101	help
102	  SPI DMA i/o-mapped base address.
103
104config GPIO_BASE
105	hex
106	default 0x1080
107	help
108	  GPIO i/o-mapped base address.
109
110config ACPI_GPE0_BASE
111	hex
112	default 0x1100
113	help
114	  ACPI General Purpose Event 0 (GPE0) i/o-mapped base address.
115	  This device is defined in ACPI specification, with 64 bytes in size.
116
117config WDT_BASE
118	hex
119	default 0x1140
120	help
121	  Watchdog timer i/o-mapped base address.
122
123config SYS_CAR_ADDR
124	hex
125	default ESRAM_BASE
126
127config SYS_CAR_SIZE
128	hex
129	default 0x8000
130	help
131	  Space in bytes in eSRAM used as Cache-As-ARM (CAR).
132	  Note this size must not exceed eSRAM's total size.
133
134config X86_TSC_TIMER_FREQ
135	int
136	default 400000000
137
138endif
139