brgphyreg.h revision 1.14
1/* $OpenBSD: brgphyreg.h,v 1.14 2010/05/24 21:23:23 sthen Exp $ */ 2 3/* 4 * Copyright (c) 2000 5 * Bill Paul <wpaul@ee.columbia.edu>. All rights reserved. 6 * 7 * Redistribution and use in source and binary forms, with or without 8 * modification, are permitted provided that the following conditions 9 * are met: 10 * 1. Redistributions of source code must retain the above copyright 11 * notice, this list of conditions and the following disclaimer. 12 * 2. Redistributions in binary form must reproduce the above copyright 13 * notice, this list of conditions and the following disclaimer in the 14 * documentation and/or other materials provided with the distribution. 15 * 3. All advertising materials mentioning features or use of this software 16 * must display the following acknowledgement: 17 * This product includes software developed by Bill Paul. 18 * 4. Neither the name of the author nor the names of any co-contributors 19 * may be used to endorse or promote products derived from this software 20 * without specific prior written permission. 21 * 22 * THIS SOFTWARE IS PROVIDED BY Bill Paul AND CONTRIBUTORS ``AS IS'' AND 23 * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE 24 * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE 25 * ARE DISCLAIMED. IN NO EVENT SHALL Bill Paul OR THE VOICES IN HIS HEAD 26 * BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR 27 * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF 28 * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS 29 * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN 30 * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) 31 * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF 32 * THE POSSIBILITY OF SUCH DAMAGE. 33 * 34 * $FreeBSD: brgphyreg.h,v 1.4 2001/09/27 17:32:49 wpaul Exp $ 35 */ 36 37#ifndef _DEV_MII_BRGPHYREG_H_ 38#define _DEV_MII_BRGPHYREG_H_ 39 40/* 41 * Broadcom BCM5400 registers 42 */ 43 44#define BRGPHY_MII_BMCR 0x00 45#define BRGPHY_BMCR_RESET 0x8000 46#define BRGPHY_BMCR_LOOP 0x4000 47#define BRGPHY_BMCR_SPD0 0x2000 /* speed select, lower bit */ 48#define BRGPHY_BMCR_AUTOEN 0x1000 /* Autoneg enabled */ 49#define BRGPHY_BMCR_PDOWN 0x0800 /* Power down */ 50#define BRGPHY_BMCR_ISO 0x0400 /* Isolate */ 51#define BRGPHY_BMCR_STARTNEG 0x0200 /* Restart autoneg */ 52#define BRGPHY_BMCR_FDX 0x0100 /* Duplex mode */ 53#define BRGPHY_BMCR_CTEST 0x0080 /* Collision test enable */ 54#define BRGPHY_BMCR_SPD1 0x0040 /* Speed select, upper bit */ 55 56#define BRGPHY_S1000 BRGPHY_BMCR_SPD1 /* 1000mbps */ 57#define BRGPHY_S100 BRGPHY_BMCR_SPD0 /* 100mpbs */ 58#define BRGPHY_S10 0 /* 10mbps */ 59 60#define BRGPHY_MII_BMSR 0x01 61#define BRGPHY_BMSR_EXTSTS 0x0100 /* Extended status present */ 62#define BRGPHY_BMSR_PRESUB 0x0040 /* Preamble suppression */ 63#define BRGPHY_BMSR_ACOMP 0x0020 /* Autoneg complete */ 64#define BRGPHY_BMSR_RFAULT 0x0010 /* Remote fault condition occurred */ 65#define BRGPHY_BMSR_ANEG 0x0008 /* Autoneg capable */ 66#define BRGPHY_BMSR_LINK 0x0004 /* Link status */ 67#define BRGPHY_BMSR_JABBER 0x0002 /* Jabber detected */ 68#define BRGPHY_BMSR_EXT 0x0001 /* Extended capability */ 69 70#define BRGPHY_MII_ANAR 0x04 71#define BRGPHY_ANAR_NP 0x8000 /* Next page */ 72#define BRGPHY_ANAR_RF 0x2000 /* Remote fault */ 73#define BRGPHY_ANAR_ASP 0x0800 /* Asymmetric Pause */ 74#define BRGPHY_ANAR_PC 0x0400 /* Pause capable */ 75#define BRGPHY_ANAR_SEL 0x001F /* selector field, 00001=Ethernet */ 76 77#define BRGPHY_MII_ANLPAR 0x05 78#define BRGPHY_ANLPAR_NP 0x8000 /* Next page */ 79#define BRGPHY_ANLPAR_RF 0x2000 /* Remote fault */ 80#define BRGPHY_ANLPAR_ASP 0x0800 /* Asymmetric Pause */ 81#define BRGPHY_ANLPAR_PC 0x0400 /* Pause capable */ 82#define BRGPHY_ANLPAR_SEL 0x001F /* selector field, 00001=Ethernet */ 83 84#define BRGPHY_SEL_TYPE 0x0001 /* ethernet */ 85 86#define BRGPHY_MII_ANER 0x06 87#define BRGPHY_ANER_PDF 0x0010 /* Parallel detection fault */ 88#define BRGPHY_ANER_LPNP 0x0008 /* Link partner can next page */ 89#define BRGPHY_ANER_NP 0x0004 /* Local PHY can next page */ 90#define BRGPHY_ANER_RX 0x0002 /* Next page received */ 91#define BRGPHY_ANER_LPAN 0x0001 /* Link partner autoneg capable */ 92 93#define BRGPHY_MII_NEXTP 0x07 /* Next page */ 94 95#define BRGPHY_MII_NEXTP_LP 0x08 /* Next page of link partner */ 96 97#define BRGPHY_MII_1000CTL 0x09 /* 1000baseT control */ 98#define BRGPHY_1000CTL_TST 0xE000 /* test modes */ 99#define BRGPHY_1000CTL_MSE 0x1000 /* Master/Slave enable */ 100#define BRGPHY_1000CTL_MSC 0x0800 /* Master/Slave configuration */ 101#define BRGPHY_1000CTL_RD 0x0400 /* Repeater/DTE */ 102#define BRGPHY_1000CTL_AFD 0x0200 /* Advertise full duplex */ 103#define BRGPHY_1000CTL_AHD 0x0100 /* Advertise half duplex */ 104 105#define BRGPHY_MII_1000STS 0x0A /* 1000baseT status */ 106#define BRGPHY_1000STS_MSF 0x8000 /* Master/slave fault */ 107#define BRGPHY_1000STS_MSR 0x4000 /* Master/slave result */ 108#define BRGPHY_1000STS_LRS 0x2000 /* Local receiver status */ 109#define BRGPHY_1000STS_RRS 0x1000 /* Remote receiver status */ 110#define BRGPHY_1000STS_LPFD 0x0800 /* Link partner can FD */ 111#define BRGPHY_1000STS_LPHD 0x0400 /* Link partner can HD */ 112#define BRGPHY_1000STS_IEC 0x00FF /* Idle error count */ 113 114#define BRGPHY_MII_EXTSTS 0x0F /* Extended status */ 115#define BRGPHY_EXTSTS_X_FD_CAP 0x8000 /* 1000base-X FD capable */ 116#define BRGPHY_EXTSTS_X_HD_CAP 0x4000 /* 1000base-X HD capable */ 117#define BRGPHY_EXTSTS_T_FD_CAP 0x2000 /* 1000base-T FD capable */ 118#define BRGPHY_EXTSTS_T_HD_CAP 0x1000 /* 1000base-T HD capable */ 119 120#define BRGPHY_MII_PHY_EXTCTL 0x10 /* PHY extended control */ 121#define BRGPHY_PHY_EXTCTL_MAC_PHY 0x8000 /* 10BIT/GMI-interface */ 122#define BRGPHY_PHY_EXTCTL_DIS_CROSS 0x4000 /* Disable MDI crossover */ 123#define BRGPHY_PHY_EXTCTL_TX_DIS 0x2000 /* Tx output disable d*/ 124#define BRGPHY_PHY_EXTCTL_INT_DIS 0x1000 /* Interrupts disabled */ 125#define BRGPHY_PHY_EXTCTL_F_INT 0x0800 /* Force interrupt */ 126#define BRGPHY_PHY_EXTCTL_BY_45 0x0400 /* Bypass 4B5B-Decoder */ 127#define BRGPHY_PHY_EXTCTL_BY_SCR 0x0200 /* Bypass scrambler */ 128#define BRGPHY_PHY_EXTCTL_BY_MLT3 0x0100 /* Bypass MLT3 encoder */ 129#define BRGPHY_PHY_EXTCTL_BY_RXA 0x0080 /* Bypass RX alignment */ 130#define BRGPHY_PHY_EXTCTL_RES_SCR 0x0040 /* Reset scrambler */ 131#define BRGPHY_PHY_EXTCTL_EN_LTR 0x0020 /* Enable LED traffic mode */ 132#define BRGPHY_PHY_EXTCTL_LED_ON 0x0010 /* Force LEDs on */ 133#define BRGPHY_PHY_EXTCTL_LED_OFF 0x0008 /* Force LEDs off */ 134#define BRGPHY_PHY_EXTCTL_EX_IPG 0x0004 /* Extended TX IPG mode */ 135#define BRGPHY_PHY_EXTCTL_3_LED 0x0002 /* Three link LED mode */ 136#define BRGPHY_PHY_EXTCTL_HIGH_LA 0x0001 /* GMII Fifo Elasticy (?) */ 137 138#define BRGPHY_MII_PHY_EXTSTS 0x11 /* PHY extended status */ 139#define BRGPHY_PHY_EXTSTS_CROSS_STAT 0x2000 /* MDI crossover status */ 140#define BRGPHY_PHY_EXTSTS_INT_STAT 0x1000 /* Interrupt status */ 141#define BRGPHY_PHY_EXTSTS_RRS 0x0800 /* Remote receiver status */ 142#define BRGPHY_PHY_EXTSTS_LRS 0x0400 /* Local receiver status */ 143#define BRGPHY_PHY_EXTSTS_LOCKED 0x0200 /* Locked */ 144#define BRGPHY_PHY_EXTSTS_LS 0x0100 /* Link status */ 145#define BRGPHY_PHY_EXTSTS_RF 0x0080 /* Remove fault */ 146#define BRGPHY_PHY_EXTSTS_CE_ER 0x0040 /* Carrier ext error */ 147#define BRGPHY_PHY_EXTSTS_BAD_SSD 0x0020 /* Bad SSD */ 148#define BRGPHY_PHY_EXTSTS_BAD_ESD 0x0010 /* Bad ESS */ 149#define BRGPHY_PHY_EXTSTS_RX_ER 0x0008 /* RX error */ 150#define BRGPHY_PHY_EXTSTS_TX_ER 0x0004 /* TX error */ 151#define BRGPHY_PHY_EXTSTS_LOCK_ER 0x0002 /* Lock error */ 152#define BRGPHY_PHY_EXTSTS_MLT3_ER 0x0001 /* MLT3 code error */ 153 154#define BRGPHY_MII_RXERRCNT 0x12 /* RX error counter */ 155 156#define BRGPHY_MII_FCERRCNT 0x13 /* false carrier sense counter */ 157#define BGRPHY_FCERRCNT 0x00FF /* False carrier counter */ 158 159#define BRGPHY_MII_RXNOCNT 0x14 /* RX not OK counter */ 160#define BRGPHY_RXNOCNT_LOCAL 0xFF00 /* Local RX not OK counter */ 161#define BRGPHY_RXNOCNT_REMOTE 0x00FF /* Local RX not OK counter */ 162 163#define BRGPHY_MII_DSP_RW_PORT 0x15 /* DSP coefficient r/w port */ 164 165#define BRGPHY_MII_EPHY_PTEST 0x17 /* 5906 PHY register */ 166#define BRGPHY_MII_DSP_ADDR_REG 0x17 /* DSP coefficient addr register */ 167 168#define BRGPHY_DSP_TAP_NUMBER_MASK 0x00 169#define BRGPHY_DSP_AGC_A 0x00 170#define BRGPHY_DSP_AGC_B 0x01 171#define BRGPHY_DSP_MSE_PAIR_STATUS 0x02 172#define BRGPHY_DSP_SOFT_DECISION 0x03 173#define BRGPHY_DSP_PHASE_REG 0x04 174#define BRGPHY_DSP_SKEW 0x05 175#define BRGPHY_DSP_POWER_SAVER_UPPER_BOUND 0x06 176#define BRGPHY_DSP_POWER_SAVER_LOWER_BOUND 0x07 177#define BRGPHY_DSP_LAST_ECHO 0x08 178#define BRGPHY_DSP_FREQUENCY 0x09 179#define BRGPHY_DSP_PLL_BANDWIDTH 0x0A 180#define BRGPHY_DSP_PLL_PHASE_OFFSET 0x0B 181 182#define BRGPHYDSP_FILTER_DCOFFSET 0x0C00 183#define BRGPHY_DSP_FILTER_FEXT3 0x0B00 184#define BRGPHY_DSP_FILTER_FEXT2 0x0A00 185#define BRGPHY_DSP_FILTER_FEXT1 0x0900 186#define BRGPHY_DSP_FILTER_FEXT0 0x0800 187#define BRGPHY_DSP_FILTER_NEXT3 0x0700 188#define BRGPHY_DSP_FILTER_NEXT2 0x0600 189#define BRGPHY_DSP_FILTER_NEXT1 0x0500 190#define BRGPHY_DSP_FILTER_NEXT0 0x0400 191#define BRGPHY_DSP_FILTER_ECHO 0x0300 192#define BRGPHY_DSP_FILTER_DFE 0x0200 193#define BRGPHY_DSP_FILTER_FFE 0x0100 194 195#define BRGPHY_DSP_CONTROL_ALL_FILTERS 0x1000 196 197#define BRGPHY_DSP_SEL_CH_0 0x0000 198#define BRGPHY_DSP_SEL_CH_1 0x2000 199#define BRGPHY_DSP_SEL_CH_2 0x4000 200#define BRGPHY_DSP_SEL_CH_3 0x6000 201 202#define BRGPHY_MII_AUXCTL 0x18 /* AUX control */ 203#define BRGPHY_AUXCTL_LOW_SQ 0x8000 /* Low squelch */ 204#define BRGPHY_AUXCTL_LONG_PKT 0x4000 /* RX long packets */ 205#define BRGPHY_AUXCTL_ER_CTL 0x3000 /* Edgerate control */ 206#define BRGPHY_AUXCTL_TX_TST 0x0400 /* TX test, always 1 */ 207#define BRGPHY_AUXCTL_DIS_PRF 0x0080 /* dis part resp filter */ 208#define BRGPHY_AUXCTL_DIAG_MODE 0x0004 /* Diagnostic mode */ 209 210#define BRGPHY_MII_AUXSTS 0x19 /* AUX status */ 211#define BRGPHY_AUXSTS_ACOMP 0x8000 /* autoneg complete */ 212#define BRGPHY_AUXSTS_AN_ACK 0x4000 /* autoneg complete ack */ 213#define BRGPHY_AUXSTS_AN_ACK_D 0x2000 /* autoneg complete ack detect */ 214#define BRGPHY_AUXSTS_AN_NPW 0x1000 /* autoneg next page wait */ 215#define BRGPHY_AUXSTS_AN_RES 0x0700 /* autoneg HCD */ 216#define BRGPHY_AUXSTS_PDF 0x0080 /* Parallel detect. fault */ 217#define BRGPHY_AUXSTS_RF 0x0040 /* remote fault */ 218#define BRGPHY_AUXSTS_ANP_R 0x0020 /* AN page received */ 219#define BRGPHY_AUXSTS_LP_ANAB 0x0010 /* LP AN ability */ 220#define BRGPHY_AUXSTS_LP_NPAB 0x0008 /* LP Next page ability */ 221#define BRGPHY_AUXSTS_LINK 0x0004 /* Link status */ 222#define BRGPHY_AUXSTS_PRR 0x0002 /* Pause resolution-RX */ 223#define BRGPHY_AUXSTS_PRT 0x0001 /* Pause resolution-TX */ 224 225#define BRGPHY_RES_1000FD 0x0700 /* 1000baseT full duplex */ 226#define BRGPHY_RES_1000HD 0x0600 /* 1000baseT half duplex */ 227#define BRGPHY_RES_100FD 0x0500 /* 100baseT full duplex */ 228#define BRGPHY_RES_100T4 0x0400 /* 100baseT4 */ 229#define BRGPHY_RES_100HD 0x0300 /* 100baseT half duplex */ 230#define BRGPHY_RES_10FD 0x0200 /* 10baseT full duplex */ 231#define BRGPHY_RES_10HD 0x0100 /* 10baseT half duplex */ 232/* 5906 */ 233#define BRGPHY_RES_100 0x0008 /* 100baseT */ 234#define BRGPHY_RES_FULL 0x0001 /* full duplex */ 235 236#define BRGPHY_MII_ISR 0x1A /* interrupt status */ 237#define BRGPHY_ISR_PSERR 0x4000 /* Pair swap error */ 238#define BRGPHY_ISR_MDXI_SC 0x2000 /* MDIX Status Change */ 239#define BRGPHY_ISR_HCT 0x1000 /* counter above 32K */ 240#define BRGPHY_ISR_LCT 0x0800 /* all counter below 128 */ 241#define BRGPHY_ISR_AN_PR 0x0400 /* Autoneg page received */ 242#define BRGPHY_ISR_NO_HDCL 0x0200 /* No HCD Link */ 243#define BRGPHY_ISR_NO_HDC 0x0100 /* No HCD */ 244#define BRGPHY_ISR_USHDC 0x0080 /* Negotiated Unsupported HCD */ 245#define BRGPHY_ISR_SCR_S_ERR 0x0040 /* Scrambler sync error */ 246#define BRGPHY_ISR_RRS_CHG 0x0020 /* Remote RX status change */ 247#define BRGPHY_ISR_LRS_CHG 0x0010 /* Local RX status change */ 248#define BRGPHY_ISR_DUP_CHG 0x0008 /* Duplex mode change */ 249#define BRGPHY_ISR_LSP_CHG 0x0004 /* Link speed changed */ 250#define BRGPHY_ISR_LNK_CHG 0x0002 /* Link status change */ 251#define BRGPHY_ISR_CRCERR 0x0001 /* CEC error */ 252 253#define BRGPHY_MII_IMR 0x1B /* interrupt mask */ 254#define BRGPHY_IMR_PSERR 0x4000 /* Pair swap error */ 255#define BRGPHY_IMR_MDXI_SC 0x2000 /* MDIX Status Change */ 256#define BRGPHY_IMR_HCT 0x1000 /* counter above 32K */ 257#define BRGPHY_IMR_LCT 0x0800 /* all counter below 128 */ 258#define BRGPHY_IMR_AN_PR 0x0400 /* Autoneg page received */ 259#define BRGPHY_IMR_NO_HDCL 0x0200 /* No HCD Link */ 260#define BRGPHY_IMR_NO_HDC 0x0100 /* No HCD */ 261#define BRGPHY_IMR_USHDC 0x0080 /* Negotiated Unsupported HCD */ 262#define BRGPHY_IMR_SCR_S_ERR 0x0040 /* Scrambler sync error */ 263#define BRGPHY_IMR_RRS_CHG 0x0020 /* Remote RX status change */ 264#define BRGPHY_IMR_LRS_CHG 0x0010 /* Local RX status change */ 265#define BRGPHY_IMR_DUP_CHG 0x0008 /* Duplex mode change */ 266#define BRGPHY_IMR_LSP_CHG 0x0004 /* Link speed changed */ 267#define BRGPHY_IMR_LNK_CHG 0x0002 /* Link status change */ 268#define BRGPHY_IMR_CRCERR 0x0001 /* CEC error */ 269 270/*******************************************************/ 271/* Begin: Shared SerDes PHY register definitions */ 272/*******************************************************/ 273 274/* SerDes autoneg is different from copper */ 275#define BRGPHY_SERDES_ANAR 0x04 276#define BRGPHY_SERDES_ANAR_FDX 0x0020 277#define BRGPHY_SERDES_ANAR_HDX 0x0040 278#define BRGPHY_SERDES_ANAR_NO_PAUSE (0x0 << 7) 279#define BRGPHY_SERDES_ANAR_SYM_PAUSE (0x1 << 7) 280#define BRGPHY_SERDES_ANAR_ASYM_PAUSE (0x2 << 7) 281#define BRGPHY_SERDES_ANAR_BOTH_PAUSE (0x3 << 7) 282 283#define BRGPHY_SERDES_ANLPAR 0x05 284#define BRGPHY_SERDES_ANLPAR_FDX 0x0020 285#define BRGPHY_SERDES_ANLPAR_HDX 0x0040 286#define BRGPHY_SERDES_ANLPAR_NO_PAUSE (0x0 << 7) 287#define BRGPHY_SERDES_ANLPAR_SYM_PAUSE (0x1 << 7) 288#define BRGPHY_SERDES_ANLPAR_ASYM_PAUSE (0x2 << 7) 289#define BRGPHY_SERDES_ANLPAR_BOTH_PAUSE (0x3 << 7) 290 291/*******************************************************/ 292/* End: Shared SerDes PHY register definitions */ 293/*******************************************************/ 294 295/*******************************************************/ 296/* Begin: PHY register values for the 5706 PHY */ 297/*******************************************************/ 298 299/* 300 * Shadow register 0x1C, bit 15 is write enable, 301 * bits 14-10 select function (0x00 to 0x1F). 302 */ 303#define BRGPHY_MII_SHADOW_1C 0x1C 304#define BRGPHY_SHADOW_1C_WRITE_EN 0x8000 305#define BRGPHY_SHADOW_1C_SELECT_MASK 0x7C00 306 307/* Shadow 0x1C Mode Control Register (select value 0x1F) */ 308#define BRGPHY_SHADOW_1C_MODE_CTRL (0x1F << 10) 309/* When set, Regs 0-0x0F are 1000X, else 1000T */ 310#define BRGPHY_SHADOW_1C_ENA_1000X 0x0001 311 312#define BRGPHY_TEST1 0x1E 313#define BRGPHY_TEST1_TRIM_EN 0x0010 314#define BRGPHY_TEST1_CRC_EN 0x8000 315 316#define BRGPHY_MII_TEST2 0x1F 317 318/*******************************************************/ 319/* End: PHY register values for the 5706 PHY */ 320/*******************************************************/ 321 322/*******************************************************/ 323/* Begin: PHY register values for the 5708S SerDes PHY */ 324/*******************************************************/ 325 326#define BRGPHY_5708S_BMCR_2500 0x20 327 328/* Autoneg Next Page Transmit 1 Regiser */ 329#define BRGPHY_5708S_ANEG_NXT_PG_XMIT1 0x0B 330#define BRGPHY_5708S_ANEG_NXT_PG_XMIT1_25G 0x0001 331 332/* Use the BLOCK_ADDR register to select the page for registers 0x10 to 0x1E */ 333#define BRGPHY_5708S_BLOCK_ADDR 0x1f 334#define BRGPHY_5708S_DIG_PG0 0x0000 335#define BRGPHY_5708S_DIG3_PG2 0x0002 336#define BRGPHY_5708S_TX_MISC_PG5 0x0005 337 338/* 5708S SerDes "Digital" Registers (page 0) */ 339#define BRGPHY_5708S_PG0_1000X_CTL1 0x10 340#define BRGPHY_5708S_PG0_1000X_CTL1_FIBER_MODE 0x0001 341#define BRGPHY_5708S_PG0_1000X_CTL1_AUTODET_EN 0x0010 342 343#define BRGPHY_5708S_PG0_1000X_STAT1 0x14 344#define BRGPHY_5708S_PG0_1000X_STAT1_SGMII 0x0001 345#define BRGPHY_5708S_PG0_1000X_STAT1_LINK 0x0002 346#define BRGPHY_5708S_PG0_1000X_STAT1_FDX 0x0004 347#define BRGPHY_5708S_PG0_1000X_STAT1_SPEED_MASK 0x0018 348#define BRGPHY_5708S_PG0_1000X_STAT1_SPEED_10 (0x0 << 3) 349#define BRGPHY_5708S_PG0_1000X_STAT1_SPEED_100 (0x1 << 3) 350#define BRGPHY_5708S_PG0_1000X_STAT1_SPEED_1G (0x2 << 3) 351#define BRGPHY_5708S_PG0_1000X_STAT1_SPEED_25G (0x3 << 3) 352 353#define BRGPHY_5708S_PG0_1000X_CTL2 0x11 354#define BRGPHY_5708S_PG0_1000X_CTL2_PAR_DET_EN 0x0001 355 356/* 5708S SerDes "Digital 3" Registers (page 2) */ 357#define BRGPHY_5708S_PG2_DIGCTL_3_0 0x10 358#define BRGPHY_5708S_PG2_DIGCTL_3_0_USE_IEEE 0x0001 359 360/* 5708S SerDes "TX Misc" Registers (page 5) */ 361#define BRGPHY_5708S_PG5_2500STATUS1 0x10 362 363#define BRGPHY_5708S_PG5_TXACTL1 0x15 364#define BRGPHY_5708S_PG5_TXACTL1_VCM 0x30 365 366#define BRGPHY_5708S_PG5_TXACTL3 0x17 367 368/*******************************************************/ 369/* End: PHY register values for the 5708S SerDes PHY */ 370/*******************************************************/ 371 372/*******************************************************/ 373/* Begin: PHY register values for the 5709S SerDes PHY */ 374/*******************************************************/ 375 376/* 5709S SerDes "General Purpose Status" Registers */ 377#define BRGPHY_BLOCK_ADDR_GP_STATUS 0x8120 378#define BRGPHY_GP_STATUS_TOP_ANEG_STATUS 0x1B 379#define BRGPHY_GP_STATUS_TOP_ANEG_SPEED_MASK 0x3F00 380#define BRGPHY_GP_STATUS_TOP_ANEG_SPEED_10 0x0000 381#define BRGPHY_GP_STATUS_TOP_ANEG_SPEED_100 0x0100 382#define BRGPHY_GP_STATUS_TOP_ANEG_SPEED_1G 0x0200 383#define BRGPHY_GP_STATUS_TOP_ANEG_SPEED_25G 0x0300 384#define BRGPHY_GP_STATUS_TOP_ANEG_SPEED_1GKX 0x0D00 385#define BRGPHY_GP_STATUS_TOP_ANEG_FDX 0x0008 386#define BRGPHY_GP_STATUS_TOP_ANEG_LINK_UP 0x0004 387#define BRGPHY_GP_STATUS_TOP_ANEG_CL73_COMP 0x0001 388 389/* 5709S SerDes "SerDes Digital" Registers */ 390#define BRGPHY_BLOCK_ADDR_SERDES_DIG 0x8300 391#define BRGPHY_SERDES_DIG_1000X_CTL1 0x0010 392#define BRGPHY_SD_DIG_1000X_CTL1_AUTODET 0x0010 393#define BRGPHY_SD_DIG_1000X_CTL1_FIBER 0x0001 394 395/* 5709S SerDes "Over 1G" Registers */ 396#define BRGPHY_BLOCK_ADDR_OVER_1G 0x8320 397#define BRGPHY_OVER_1G_UNFORMAT_PG1 0x19 398 399/* 5709S SerDes "Multi-Rate Backplane Ethernet" Registers */ 400#define BRGPHY_BLOCK_ADDR_MRBE 0x8350 401#define BRGPHY_MRBE_MSG_PG5_NP 0x10 402#define BRGPHY_MRBE_MSG_PG5_NP_MBRE 0x0001 403#define BRGPHY_MRBE_MSG_PG5_NP_T2 0x0001 404 405/* 5709S SerDes "IEEE Clause 73 User B0" Registers */ 406#define BRGPHY_BLOCK_ADDR_CL73_USER_B0 0x8370 407#define BRGPHY_CL73_USER_B0_MBRE_CTL1 0x12 408#define BRGPHY_CL73_USER_B0_MBRE_CTL1_NP_AFT_BP 0x2000 409#define BRGPHY_CL73_USER_B0_MBRE_CTL1_STA_MGR 0x4000 410#define BRGPHY_CL73_USER_B0_MBRE_CTL1_ANEG 0x8000 411 412/* 5709S SerDes "IEEE Clause 73 User B0" Registers */ 413#define BRGPHY_BLOCK_ADDR_ADDR_EXT 0xFFD0 414 415/* 5709S SerDes "Combo IEEE 0" Registers */ 416#define BRGPHY_BLOCK_ADDR_COMBO_IEEE0 0xFFE0 417 418#define BRGPHY_ADDR_EXT 0x1E 419#define BRGPHY_BLOCK_ADDR 0x1F 420 421#define BRGPHY_ADDR_EXT_AN_MMD 0x3800 422 423/*******************************************************/ 424/* End: PHY register values for the 5709S SerDes PHY */ 425/*******************************************************/ 426 427#define BRGPHY_INTRS \ 428 ~(BRGPHY_IMR_LNK_CHG|BRGPHY_IMR_LSP_CHG|BRGPHY_IMR_DUP_CHG) 429 430#endif /* _DEV_BRGPHY_MIIREG_H_ */ 431