1/* 2 * Atmel AT45xxx DataFlash MTD driver for lightweight SPI framework 3 * 4 * Largely derived from at91_dataflash.c: 5 * Copyright (C) 2003-2005 SAN People (Pty) Ltd 6 * 7 * This program is free software; you can redistribute it and/or 8 * modify it under the terms of the GNU General Public License 9 * as published by the Free Software Foundation; either version 10 * 2 of the License, or (at your option) any later version. 11*/ 12#include <linux/module.h> 13#include <linux/init.h> 14#include <linux/slab.h> 15#include <linux/delay.h> 16#include <linux/device.h> 17#include <linux/spi/spi.h> 18#include <linux/spi/flash.h> 19 20#include <linux/mtd/mtd.h> 21#include <linux/mtd/partitions.h> 22 23 24/* 25 * DataFlash is a kind of SPI flash. Most AT45 chips have two buffers in 26 * each chip, which may be used for double buffered I/O; but this driver 27 * doesn't (yet) use these for any kind of i/o overlap or prefetching. 28 * 29 * Sometimes DataFlash is packaged in MMC-format cards, although the 30 * MMC stack can't use SPI (yet), or distinguish between MMC and DataFlash 31 * protocols during enumeration. 32 */ 33 34#define CONFIG_DATAFLASH_WRITE_VERIFY 35 36/* reads can bypass the buffers */ 37#define OP_READ_CONTINUOUS 0xE8 38#define OP_READ_PAGE 0xD2 39 40/* group B requests can run even while status reports "busy" */ 41#define OP_READ_STATUS 0xD7 /* group B */ 42 43/* move data between host and buffer */ 44#define OP_READ_BUFFER1 0xD4 /* group B */ 45#define OP_READ_BUFFER2 0xD6 /* group B */ 46#define OP_WRITE_BUFFER1 0x84 /* group B */ 47#define OP_WRITE_BUFFER2 0x87 /* group B */ 48 49/* erasing flash */ 50#define OP_ERASE_PAGE 0x81 51#define OP_ERASE_BLOCK 0x50 52 53/* move data between buffer and flash */ 54#define OP_TRANSFER_BUF1 0x53 55#define OP_TRANSFER_BUF2 0x55 56#define OP_MREAD_BUFFER1 0xD4 57#define OP_MREAD_BUFFER2 0xD6 58#define OP_MWERASE_BUFFER1 0x83 59#define OP_MWERASE_BUFFER2 0x86 60#define OP_MWRITE_BUFFER1 0x88 /* sector must be pre-erased */ 61#define OP_MWRITE_BUFFER2 0x89 /* sector must be pre-erased */ 62 63/* write to buffer, then write-erase to flash */ 64#define OP_PROGRAM_VIA_BUF1 0x82 65#define OP_PROGRAM_VIA_BUF2 0x85 66 67/* compare buffer to flash */ 68#define OP_COMPARE_BUF1 0x60 69#define OP_COMPARE_BUF2 0x61 70 71/* read flash to buffer, then write-erase to flash */ 72#define OP_REWRITE_VIA_BUF1 0x58 73#define OP_REWRITE_VIA_BUF2 0x59 74 75/* newer chips report JEDEC manufacturer and device IDs; chip 76 * serial number and OTP bits; and per-sector writeprotect. 77 */ 78#define OP_READ_ID 0x9F 79#define OP_READ_SECURITY 0x77 80#define OP_WRITE_SECURITY 0x9A /* OTP bits */ 81 82 83struct dataflash { 84 u8 command[4]; 85 char name[24]; 86 87 unsigned partitioned:1; 88 89 unsigned short page_offset; /* offset in flash address */ 90 unsigned int page_size; /* of bytes per page */ 91 92 struct semaphore lock; 93 struct spi_device *spi; 94 95 struct mtd_info mtd; 96}; 97 98#ifdef CONFIG_MTD_PARTITIONS 99#define mtd_has_partitions() (1) 100#else 101#define mtd_has_partitions() (0) 102#endif 103 104/* ......................................................................... */ 105 106/* 107 * Return the status of the DataFlash device. 108 */ 109static inline int dataflash_status(struct spi_device *spi) 110{ 111 /* NOTE: at45db321c over 25 MHz wants to write 112 * a dummy byte after the opcode... 113 */ 114 return spi_w8r8(spi, OP_READ_STATUS); 115} 116 117/* 118 * Poll the DataFlash device until it is READY. 119 * This usually takes 5-20 msec or so; more for sector erase. 120 */ 121static int dataflash_waitready(struct spi_device *spi) 122{ 123 int status; 124 125 for (;;) { 126 status = dataflash_status(spi); 127 if (status < 0) { 128 DEBUG(MTD_DEBUG_LEVEL1, "%s: status %d?\n", 129 spi->dev.bus_id, status); 130 status = 0; 131 } 132 133 if (status & (1 << 7)) /* RDY/nBSY */ 134 return status; 135 136 msleep(3); 137 } 138} 139 140/* ......................................................................... */ 141 142/* 143 * Erase pages of flash. 144 */ 145static int dataflash_erase(struct mtd_info *mtd, struct erase_info *instr) 146{ 147 struct dataflash *priv = (struct dataflash *)mtd->priv; 148 struct spi_device *spi = priv->spi; 149 struct spi_transfer x = { .tx_dma = 0, }; 150 struct spi_message msg; 151 unsigned blocksize = priv->page_size << 3; 152 u8 *command; 153 154 DEBUG(MTD_DEBUG_LEVEL2, "%s: erase addr=0x%x len 0x%x\n", 155 spi->dev.bus_id, 156 instr->addr, instr->len); 157 158 /* Sanity checks */ 159 if ((instr->addr + instr->len) > mtd->size 160 || (instr->len % priv->page_size) != 0 161 || (instr->addr % priv->page_size) != 0) 162 return -EINVAL; 163 164 spi_message_init(&msg); 165 166 x.tx_buf = command = priv->command; 167 x.len = 4; 168 spi_message_add_tail(&x, &msg); 169 170 down(&priv->lock); 171 while (instr->len > 0) { 172 unsigned int pageaddr; 173 int status; 174 int do_block; 175 176 /* Calculate flash page address; use block erase (for speed) if 177 * we're at a block boundary and need to erase the whole block. 178 */ 179 pageaddr = instr->addr / priv->page_size; 180 do_block = (pageaddr & 0x7) == 0 && instr->len >= blocksize; 181 pageaddr = pageaddr << priv->page_offset; 182 183 command[0] = do_block ? OP_ERASE_BLOCK : OP_ERASE_PAGE; 184 command[1] = (u8)(pageaddr >> 16); 185 command[2] = (u8)(pageaddr >> 8); 186 command[3] = 0; 187 188 DEBUG(MTD_DEBUG_LEVEL3, "ERASE %s: (%x) %x %x %x [%i]\n", 189 do_block ? "block" : "page", 190 command[0], command[1], command[2], command[3], 191 pageaddr); 192 193 status = spi_sync(spi, &msg); 194 (void) dataflash_waitready(spi); 195 196 if (status < 0) { 197 printk(KERN_ERR "%s: erase %x, err %d\n", 198 spi->dev.bus_id, pageaddr, status); 199 /* REVISIT: can retry instr->retries times; or 200 * giveup and instr->fail_addr = instr->addr; 201 */ 202 continue; 203 } 204 205 if (do_block) { 206 instr->addr += blocksize; 207 instr->len -= blocksize; 208 } else { 209 instr->addr += priv->page_size; 210 instr->len -= priv->page_size; 211 } 212 } 213 up(&priv->lock); 214 215 /* Inform MTD subsystem that erase is complete */ 216 instr->state = MTD_ERASE_DONE; 217 mtd_erase_callback(instr); 218 219 return 0; 220} 221 222/* 223 * Read from the DataFlash device. 224 * from : Start offset in flash device 225 * len : Amount to read 226 * retlen : About of data actually read 227 * buf : Buffer containing the data 228 */ 229static int dataflash_read(struct mtd_info *mtd, loff_t from, size_t len, 230 size_t *retlen, u_char *buf) 231{ 232 struct dataflash *priv = (struct dataflash *)mtd->priv; 233 struct spi_transfer x[2] = { { .tx_dma = 0, }, }; 234 struct spi_message msg; 235 unsigned int addr; 236 u8 *command; 237 int status; 238 239 DEBUG(MTD_DEBUG_LEVEL2, "%s: read 0x%x..0x%x\n", 240 priv->spi->dev.bus_id, (unsigned)from, (unsigned)(from + len)); 241 242 *retlen = 0; 243 244 /* Sanity checks */ 245 if (!len) 246 return 0; 247 if (from + len > mtd->size) 248 return -EINVAL; 249 250 /* Calculate flash page/byte address */ 251 addr = (((unsigned)from / priv->page_size) << priv->page_offset) 252 + ((unsigned)from % priv->page_size); 253 254 command = priv->command; 255 256 DEBUG(MTD_DEBUG_LEVEL3, "READ: (%x) %x %x %x\n", 257 command[0], command[1], command[2], command[3]); 258 259 spi_message_init(&msg); 260 261 x[0].tx_buf = command; 262 x[0].len = 8; 263 spi_message_add_tail(&x[0], &msg); 264 265 x[1].rx_buf = buf; 266 x[1].len = len; 267 spi_message_add_tail(&x[1], &msg); 268 269 down(&priv->lock); 270 271 /* Continuous read, max clock = f(car) which may be less than 272 * the peak rate available. Some chips support commands with 273 * fewer "don't care" bytes. Both buffers stay unchanged. 274 */ 275 command[0] = OP_READ_CONTINUOUS; 276 command[1] = (u8)(addr >> 16); 277 command[2] = (u8)(addr >> 8); 278 command[3] = (u8)(addr >> 0); 279 /* plus 4 "don't care" bytes */ 280 281 status = spi_sync(priv->spi, &msg); 282 up(&priv->lock); 283 284 if (status >= 0) { 285 *retlen = msg.actual_length - 8; 286 status = 0; 287 } else 288 DEBUG(MTD_DEBUG_LEVEL1, "%s: read %x..%x --> %d\n", 289 priv->spi->dev.bus_id, 290 (unsigned)from, (unsigned)(from + len), 291 status); 292 return status; 293} 294 295/* 296 * Write to the DataFlash device. 297 * to : Start offset in flash device 298 * len : Amount to write 299 * retlen : Amount of data actually written 300 * buf : Buffer containing the data 301 */ 302static int dataflash_write(struct mtd_info *mtd, loff_t to, size_t len, 303 size_t * retlen, const u_char * buf) 304{ 305 struct dataflash *priv = (struct dataflash *)mtd->priv; 306 struct spi_device *spi = priv->spi; 307 struct spi_transfer x[2] = { { .tx_dma = 0, }, }; 308 struct spi_message msg; 309 unsigned int pageaddr, addr, offset, writelen; 310 size_t remaining = len; 311 u_char *writebuf = (u_char *) buf; 312 int status = -EINVAL; 313 u8 *command; 314 315 DEBUG(MTD_DEBUG_LEVEL2, "%s: write 0x%x..0x%x\n", 316 spi->dev.bus_id, (unsigned)to, (unsigned)(to + len)); 317 318 *retlen = 0; 319 320 /* Sanity checks */ 321 if (!len) 322 return 0; 323 if ((to + len) > mtd->size) 324 return -EINVAL; 325 326 spi_message_init(&msg); 327 328 x[0].tx_buf = command = priv->command; 329 x[0].len = 4; 330 spi_message_add_tail(&x[0], &msg); 331 332 pageaddr = ((unsigned)to / priv->page_size); 333 offset = ((unsigned)to % priv->page_size); 334 if (offset + len > priv->page_size) 335 writelen = priv->page_size - offset; 336 else 337 writelen = len; 338 339 down(&priv->lock); 340 while (remaining > 0) { 341 DEBUG(MTD_DEBUG_LEVEL3, "write @ %i:%i len=%i\n", 342 pageaddr, offset, writelen); 343 344 /* REVISIT: 345 * (a) each page in a sector must be rewritten at least 346 * once every 10K sibling erase/program operations. 347 * (b) for pages that are already erased, we could 348 * use WRITE+MWRITE not PROGRAM for ~30% speedup. 349 * (c) WRITE to buffer could be done while waiting for 350 * a previous MWRITE/MWERASE to complete ... 351 * (d) error handling here seems to be mostly missing. 352 * 353 * Two persistent bits per page, plus a per-sector counter, 354 * could support (a) and (b) ... we might consider using 355 * the second half of sector zero, which is just one block, 356 * to track that state. (On AT91, that sector should also 357 * support boot-from-DataFlash.) 358 */ 359 360 addr = pageaddr << priv->page_offset; 361 362 /* (1) Maybe transfer partial page to Buffer1 */ 363 if (writelen != priv->page_size) { 364 command[0] = OP_TRANSFER_BUF1; 365 command[1] = (addr & 0x00FF0000) >> 16; 366 command[2] = (addr & 0x0000FF00) >> 8; 367 command[3] = 0; 368 369 DEBUG(MTD_DEBUG_LEVEL3, "TRANSFER: (%x) %x %x %x\n", 370 command[0], command[1], command[2], command[3]); 371 372 status = spi_sync(spi, &msg); 373 if (status < 0) 374 DEBUG(MTD_DEBUG_LEVEL1, "%s: xfer %u -> %d \n", 375 spi->dev.bus_id, addr, status); 376 377 (void) dataflash_waitready(priv->spi); 378 } 379 380 /* (2) Program full page via Buffer1 */ 381 addr += offset; 382 command[0] = OP_PROGRAM_VIA_BUF1; 383 command[1] = (addr & 0x00FF0000) >> 16; 384 command[2] = (addr & 0x0000FF00) >> 8; 385 command[3] = (addr & 0x000000FF); 386 387 DEBUG(MTD_DEBUG_LEVEL3, "PROGRAM: (%x) %x %x %x\n", 388 command[0], command[1], command[2], command[3]); 389 390 x[1].tx_buf = writebuf; 391 x[1].len = writelen; 392 spi_message_add_tail(x + 1, &msg); 393 status = spi_sync(spi, &msg); 394 spi_transfer_del(x + 1); 395 if (status < 0) 396 DEBUG(MTD_DEBUG_LEVEL1, "%s: pgm %u/%u -> %d \n", 397 spi->dev.bus_id, addr, writelen, status); 398 399 (void) dataflash_waitready(priv->spi); 400 401 402#ifdef CONFIG_DATAFLASH_WRITE_VERIFY 403 404 /* (3) Compare to Buffer1 */ 405 addr = pageaddr << priv->page_offset; 406 command[0] = OP_COMPARE_BUF1; 407 command[1] = (addr & 0x00FF0000) >> 16; 408 command[2] = (addr & 0x0000FF00) >> 8; 409 command[3] = 0; 410 411 DEBUG(MTD_DEBUG_LEVEL3, "COMPARE: (%x) %x %x %x\n", 412 command[0], command[1], command[2], command[3]); 413 414 status = spi_sync(spi, &msg); 415 if (status < 0) 416 DEBUG(MTD_DEBUG_LEVEL1, "%s: compare %u -> %d \n", 417 spi->dev.bus_id, addr, status); 418 419 status = dataflash_waitready(priv->spi); 420 421 /* Check result of the compare operation */ 422 if ((status & (1 << 6)) == 1) { 423 printk(KERN_ERR "%s: compare page %u, err %d\n", 424 spi->dev.bus_id, pageaddr, status); 425 remaining = 0; 426 status = -EIO; 427 break; 428 } else 429 status = 0; 430 431#endif /* CONFIG_DATAFLASH_WRITE_VERIFY */ 432 433 remaining = remaining - writelen; 434 pageaddr++; 435 offset = 0; 436 writebuf += writelen; 437 *retlen += writelen; 438 439 if (remaining > priv->page_size) 440 writelen = priv->page_size; 441 else 442 writelen = remaining; 443 } 444 up(&priv->lock); 445 446 return status; 447} 448 449/* ......................................................................... */ 450 451/* 452 * Register DataFlash device with MTD subsystem. 453 */ 454static int __devinit 455add_dataflash(struct spi_device *spi, char *name, 456 int nr_pages, int pagesize, int pageoffset) 457{ 458 struct dataflash *priv; 459 struct mtd_info *device; 460 struct flash_platform_data *pdata = spi->dev.platform_data; 461 462 priv = kzalloc(sizeof *priv, GFP_KERNEL); 463 if (!priv) 464 return -ENOMEM; 465 466 init_MUTEX(&priv->lock); 467 priv->spi = spi; 468 priv->page_size = pagesize; 469 priv->page_offset = pageoffset; 470 471 /* name must be usable with cmdlinepart */ 472 sprintf(priv->name, "spi%d.%d-%s", 473 spi->master->bus_num, spi->chip_select, 474 name); 475 476 device = &priv->mtd; 477 device->name = (pdata && pdata->name) ? pdata->name : priv->name; 478 device->size = nr_pages * pagesize; 479 device->erasesize = pagesize; 480 device->writesize = pagesize; 481 device->owner = THIS_MODULE; 482 device->type = MTD_DATAFLASH; 483 device->flags = MTD_WRITEABLE; 484 device->erase = dataflash_erase; 485 device->read = dataflash_read; 486 device->write = dataflash_write; 487 device->priv = priv; 488 489 dev_info(&spi->dev, "%s (%d KBytes)\n", name, device->size/1024); 490 dev_set_drvdata(&spi->dev, priv); 491 492 if (mtd_has_partitions()) { 493 struct mtd_partition *parts; 494 int nr_parts = 0; 495 496#ifdef CONFIG_MTD_CMDLINE_PARTS 497 static const char *part_probes[] = { "cmdlinepart", NULL, }; 498 499 nr_parts = parse_mtd_partitions(device, part_probes, &parts, 0); 500#endif 501 502 if (nr_parts <= 0 && pdata && pdata->parts) { 503 parts = pdata->parts; 504 nr_parts = pdata->nr_parts; 505 } 506 507 if (nr_parts > 0) { 508 priv->partitioned = 1; 509 return add_mtd_partitions(device, parts, nr_parts); 510 } 511 } else if (pdata && pdata->nr_parts) 512 dev_warn(&spi->dev, "ignoring %d default partitions on %s\n", 513 pdata->nr_parts, device->name); 514 515 return add_mtd_device(device) == 1 ? -ENODEV : 0; 516} 517 518/* 519 * Detect and initialize DataFlash device: 520 * 521 * Device Density ID code #Pages PageSize Offset 522 * AT45DB011B 1Mbit (128K) xx0011xx (0x0c) 512 264 9 523 * AT45DB021B 2Mbit (256K) xx0101xx (0x14) 1025 264 9 524 * AT45DB041B 4Mbit (512K) xx0111xx (0x1c) 2048 264 9 525 * AT45DB081B 8Mbit (1M) xx1001xx (0x24) 4096 264 9 526 * AT45DB0161B 16Mbit (2M) xx1011xx (0x2c) 4096 528 10 527 * AT45DB0321B 32Mbit (4M) xx1101xx (0x34) 8192 528 10 528 * AT45DB0642 64Mbit (8M) xx111xxx (0x3c) 8192 1056 11 529 * AT45DB1282 128Mbit (16M) xx0100xx (0x10) 16384 1056 11 530 */ 531static int __devinit dataflash_probe(struct spi_device *spi) 532{ 533 int status; 534 535 status = dataflash_status(spi); 536 if (status <= 0 || status == 0xff) { 537 DEBUG(MTD_DEBUG_LEVEL1, "%s: status error %d\n", 538 spi->dev.bus_id, status); 539 if (status == 0 || status == 0xff) 540 status = -ENODEV; 541 return status; 542 } 543 544 /* if there's a device there, assume it's dataflash. 545 * board setup should have set spi->max_speed_max to 546 * match f(car) for continuous reads, mode 0 or 3. 547 */ 548 switch (status & 0x3c) { 549 case 0x0c: /* 0 0 1 1 x x */ 550 status = add_dataflash(spi, "AT45DB011B", 512, 264, 9); 551 break; 552 case 0x14: /* 0 1 0 1 x x */ 553 status = add_dataflash(spi, "AT45DB021B", 1025, 264, 9); 554 break; 555 case 0x1c: /* 0 1 1 1 x x */ 556 status = add_dataflash(spi, "AT45DB041x", 2048, 264, 9); 557 break; 558 case 0x24: /* 1 0 0 1 x x */ 559 status = add_dataflash(spi, "AT45DB081B", 4096, 264, 9); 560 break; 561 case 0x2c: /* 1 0 1 1 x x */ 562 status = add_dataflash(spi, "AT45DB161x", 4096, 528, 10); 563 break; 564 case 0x34: /* 1 1 0 1 x x */ 565 status = add_dataflash(spi, "AT45DB321x", 8192, 528, 10); 566 break; 567 case 0x38: /* 1 1 1 x x x */ 568 case 0x3c: 569 status = add_dataflash(spi, "AT45DB642x", 8192, 1056, 11); 570 break; 571 /* obsolete AT45DB1282 not (yet?) supported */ 572 default: 573 DEBUG(MTD_DEBUG_LEVEL1, "%s: unsupported device (%x)\n", 574 spi->dev.bus_id, status & 0x3c); 575 status = -ENODEV; 576 } 577 578 if (status < 0) 579 DEBUG(MTD_DEBUG_LEVEL1, "%s: add_dataflash --> %d\n", 580 spi->dev.bus_id, status); 581 582 return status; 583} 584 585static int __devexit dataflash_remove(struct spi_device *spi) 586{ 587 struct dataflash *flash = dev_get_drvdata(&spi->dev); 588 int status; 589 590 DEBUG(MTD_DEBUG_LEVEL1, "%s: remove\n", spi->dev.bus_id); 591 592 if (mtd_has_partitions() && flash->partitioned) 593 status = del_mtd_partitions(&flash->mtd); 594 else 595 status = del_mtd_device(&flash->mtd); 596 if (status == 0) 597 kfree(flash); 598 return status; 599} 600 601static struct spi_driver dataflash_driver = { 602 .driver = { 603 .name = "mtd_dataflash", 604 .bus = &spi_bus_type, 605 .owner = THIS_MODULE, 606 }, 607 608 .probe = dataflash_probe, 609 .remove = __devexit_p(dataflash_remove), 610 611}; 612 613static int __init dataflash_init(void) 614{ 615 return spi_register_driver(&dataflash_driver); 616} 617module_init(dataflash_init); 618 619static void __exit dataflash_exit(void) 620{ 621 spi_unregister_driver(&dataflash_driver); 622} 623module_exit(dataflash_exit); 624 625 626MODULE_LICENSE("GPL"); 627MODULE_AUTHOR("Andrew Victor, David Brownell"); 628MODULE_DESCRIPTION("MTD DataFlash driver"); 629