1#ifndef NET2280_H 2#define NET2280_H 3/* 4 * NetChip 2280 high/full speed USB device controller. 5 * Unlike many such controllers, this one talks PCI. 6 */ 7 8/* 9 * Copyright (C) 2002 NetChip Technology, Inc. (http://www.netchip.com) 10 * Copyright (C) 2003 David Brownell 11 * 12 * This program is free software; you can redistribute it and/or modify 13 * it under the terms of the GNU General Public License as published by 14 * the Free Software Foundation; either version 2 of the License, or 15 * (at your option) any later version. 16 * 17 * This program is distributed in the hope that it will be useful, 18 * but WITHOUT ANY WARRANTY; without even the implied warranty of 19 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the 20 * GNU General Public License for more details. 21 * 22 * You should have received a copy of the GNU General Public License 23 * along with this program; if not, write to the Free Software 24 * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA 25 */ 26 27/*-------------------------------------------------------------------------*/ 28 29/* NET2280 MEMORY MAPPED REGISTERS 30 * 31 * The register layout came from the chip documentation, and the bit 32 * number definitions were extracted from chip specification. 33 * 34 * Use the shift operator ('<<') to build bit masks, with readl/writel 35 * to access the registers through PCI. 36 */ 37 38/* main registers, BAR0 + 0x0000 */ 39struct net2280_regs { 40 /* offset 0x0000 */ 41 __le32 devinit; 42#define LOCAL_CLOCK_FREQUENCY 8 43#define FORCE_PCI_RESET 7 44#define PCI_ID 6 45#define PCI_ENABLE 5 46#define FIFO_SOFT_RESET 4 47#define CFG_SOFT_RESET 3 48#define PCI_SOFT_RESET 2 49#define USB_SOFT_RESET 1 50#define M8051_RESET 0 51 __le32 eectl; 52#define EEPROM_ADDRESS_WIDTH 23 53#define EEPROM_CHIP_SELECT_ACTIVE 22 54#define EEPROM_PRESENT 21 55#define EEPROM_VALID 20 56#define EEPROM_BUSY 19 57#define EEPROM_CHIP_SELECT_ENABLE 18 58#define EEPROM_BYTE_READ_START 17 59#define EEPROM_BYTE_WRITE_START 16 60#define EEPROM_READ_DATA 8 61#define EEPROM_WRITE_DATA 0 62 __le32 eeclkfreq; 63 u32 _unused0; 64 /* offset 0x0010 */ 65 66 __le32 pciirqenb0; /* interrupt PCI master ... */ 67#define SETUP_PACKET_INTERRUPT_ENABLE 7 68#define ENDPOINT_F_INTERRUPT_ENABLE 6 69#define ENDPOINT_E_INTERRUPT_ENABLE 5 70#define ENDPOINT_D_INTERRUPT_ENABLE 4 71#define ENDPOINT_C_INTERRUPT_ENABLE 3 72#define ENDPOINT_B_INTERRUPT_ENABLE 2 73#define ENDPOINT_A_INTERRUPT_ENABLE 1 74#define ENDPOINT_0_INTERRUPT_ENABLE 0 75 __le32 pciirqenb1; 76#define PCI_INTERRUPT_ENABLE 31 77#define POWER_STATE_CHANGE_INTERRUPT_ENABLE 27 78#define PCI_ARBITER_TIMEOUT_INTERRUPT_ENABLE 26 79#define PCI_PARITY_ERROR_INTERRUPT_ENABLE 25 80#define PCI_MASTER_ABORT_RECEIVED_INTERRUPT_ENABLE 20 81#define PCI_TARGET_ABORT_RECEIVED_INTERRUPT_ENABLE 19 82#define PCI_TARGET_ABORT_ASSERTED_INTERRUPT_ENABLE 18 83#define PCI_RETRY_ABORT_INTERRUPT_ENABLE 17 84#define PCI_MASTER_CYCLE_DONE_INTERRUPT_ENABLE 16 85#define GPIO_INTERRUPT_ENABLE 13 86#define DMA_D_INTERRUPT_ENABLE 12 87#define DMA_C_INTERRUPT_ENABLE 11 88#define DMA_B_INTERRUPT_ENABLE 10 89#define DMA_A_INTERRUPT_ENABLE 9 90#define EEPROM_DONE_INTERRUPT_ENABLE 8 91#define VBUS_INTERRUPT_ENABLE 7 92#define CONTROL_STATUS_INTERRUPT_ENABLE 6 93#define ROOT_PORT_RESET_INTERRUPT_ENABLE 4 94#define SUSPEND_REQUEST_INTERRUPT_ENABLE 3 95#define SUSPEND_REQUEST_CHANGE_INTERRUPT_ENABLE 2 96#define RESUME_INTERRUPT_ENABLE 1 97#define SOF_INTERRUPT_ENABLE 0 98 __le32 cpu_irqenb0; /* ... or onboard 8051 */ 99#define SETUP_PACKET_INTERRUPT_ENABLE 7 100#define ENDPOINT_F_INTERRUPT_ENABLE 6 101#define ENDPOINT_E_INTERRUPT_ENABLE 5 102#define ENDPOINT_D_INTERRUPT_ENABLE 4 103#define ENDPOINT_C_INTERRUPT_ENABLE 3 104#define ENDPOINT_B_INTERRUPT_ENABLE 2 105#define ENDPOINT_A_INTERRUPT_ENABLE 1 106#define ENDPOINT_0_INTERRUPT_ENABLE 0 107 __le32 cpu_irqenb1; 108#define CPU_INTERRUPT_ENABLE 31 109#define POWER_STATE_CHANGE_INTERRUPT_ENABLE 27 110#define PCI_ARBITER_TIMEOUT_INTERRUPT_ENABLE 26 111#define PCI_PARITY_ERROR_INTERRUPT_ENABLE 25 112#define PCI_INTA_INTERRUPT_ENABLE 24 113#define PCI_PME_INTERRUPT_ENABLE 23 114#define PCI_SERR_INTERRUPT_ENABLE 22 115#define PCI_PERR_INTERRUPT_ENABLE 21 116#define PCI_MASTER_ABORT_RECEIVED_INTERRUPT_ENABLE 20 117#define PCI_TARGET_ABORT_RECEIVED_INTERRUPT_ENABLE 19 118#define PCI_RETRY_ABORT_INTERRUPT_ENABLE 17 119#define PCI_MASTER_CYCLE_DONE_INTERRUPT_ENABLE 16 120#define GPIO_INTERRUPT_ENABLE 13 121#define DMA_D_INTERRUPT_ENABLE 12 122#define DMA_C_INTERRUPT_ENABLE 11 123#define DMA_B_INTERRUPT_ENABLE 10 124#define DMA_A_INTERRUPT_ENABLE 9 125#define EEPROM_DONE_INTERRUPT_ENABLE 8 126#define VBUS_INTERRUPT_ENABLE 7 127#define CONTROL_STATUS_INTERRUPT_ENABLE 6 128#define ROOT_PORT_RESET_INTERRUPT_ENABLE 4 129#define SUSPEND_REQUEST_INTERRUPT_ENABLE 3 130#define SUSPEND_REQUEST_CHANGE_INTERRUPT_ENABLE 2 131#define RESUME_INTERRUPT_ENABLE 1 132#define SOF_INTERRUPT_ENABLE 0 133 134 /* offset 0x0020 */ 135 u32 _unused1; 136 __le32 usbirqenb1; 137#define USB_INTERRUPT_ENABLE 31 138#define POWER_STATE_CHANGE_INTERRUPT_ENABLE 27 139#define PCI_ARBITER_TIMEOUT_INTERRUPT_ENABLE 26 140#define PCI_PARITY_ERROR_INTERRUPT_ENABLE 25 141#define PCI_INTA_INTERRUPT_ENABLE 24 142#define PCI_PME_INTERRUPT_ENABLE 23 143#define PCI_SERR_INTERRUPT_ENABLE 22 144#define PCI_PERR_INTERRUPT_ENABLE 21 145#define PCI_MASTER_ABORT_RECEIVED_INTERRUPT_ENABLE 20 146#define PCI_TARGET_ABORT_RECEIVED_INTERRUPT_ENABLE 19 147#define PCI_RETRY_ABORT_INTERRUPT_ENABLE 17 148#define PCI_MASTER_CYCLE_DONE_INTERRUPT_ENABLE 16 149#define GPIO_INTERRUPT_ENABLE 13 150#define DMA_D_INTERRUPT_ENABLE 12 151#define DMA_C_INTERRUPT_ENABLE 11 152#define DMA_B_INTERRUPT_ENABLE 10 153#define DMA_A_INTERRUPT_ENABLE 9 154#define EEPROM_DONE_INTERRUPT_ENABLE 8 155#define VBUS_INTERRUPT_ENABLE 7 156#define CONTROL_STATUS_INTERRUPT_ENABLE 6 157#define ROOT_PORT_RESET_INTERRUPT_ENABLE 4 158#define SUSPEND_REQUEST_INTERRUPT_ENABLE 3 159#define SUSPEND_REQUEST_CHANGE_INTERRUPT_ENABLE 2 160#define RESUME_INTERRUPT_ENABLE 1 161#define SOF_INTERRUPT_ENABLE 0 162 __le32 irqstat0; 163#define INTA_ASSERTED 12 164#define SETUP_PACKET_INTERRUPT 7 165#define ENDPOINT_F_INTERRUPT 6 166#define ENDPOINT_E_INTERRUPT 5 167#define ENDPOINT_D_INTERRUPT 4 168#define ENDPOINT_C_INTERRUPT 3 169#define ENDPOINT_B_INTERRUPT 2 170#define ENDPOINT_A_INTERRUPT 1 171#define ENDPOINT_0_INTERRUPT 0 172 __le32 irqstat1; 173#define POWER_STATE_CHANGE_INTERRUPT 27 174#define PCI_ARBITER_TIMEOUT_INTERRUPT 26 175#define PCI_PARITY_ERROR_INTERRUPT 25 176#define PCI_INTA_INTERRUPT 24 177#define PCI_PME_INTERRUPT 23 178#define PCI_SERR_INTERRUPT 22 179#define PCI_PERR_INTERRUPT 21 180#define PCI_MASTER_ABORT_RECEIVED_INTERRUPT 20 181#define PCI_TARGET_ABORT_RECEIVED_INTERRUPT 19 182#define PCI_RETRY_ABORT_INTERRUPT 17 183#define PCI_MASTER_CYCLE_DONE_INTERRUPT 16 184#define GPIO_INTERRUPT 13 185#define DMA_D_INTERRUPT 12 186#define DMA_C_INTERRUPT 11 187#define DMA_B_INTERRUPT 10 188#define DMA_A_INTERRUPT 9 189#define EEPROM_DONE_INTERRUPT 8 190#define VBUS_INTERRUPT 7 191#define CONTROL_STATUS_INTERRUPT 6 192#define ROOT_PORT_RESET_INTERRUPT 4 193#define SUSPEND_REQUEST_INTERRUPT 3 194#define SUSPEND_REQUEST_CHANGE_INTERRUPT 2 195#define RESUME_INTERRUPT 1 196#define SOF_INTERRUPT 0 197 /* offset 0x0030 */ 198 __le32 idxaddr; 199 __le32 idxdata; 200 __le32 fifoctl; 201#define PCI_BASE2_RANGE 16 202#define IGNORE_FIFO_AVAILABILITY 3 203#define PCI_BASE2_SELECT 2 204#define FIFO_CONFIGURATION_SELECT 0 205 u32 _unused2; 206 /* offset 0x0040 */ 207 __le32 memaddr; 208#define START 28 209#define DIRECTION 27 210#define FIFO_DIAGNOSTIC_SELECT 24 211#define MEMORY_ADDRESS 0 212 __le32 memdata0; 213 __le32 memdata1; 214 u32 _unused3; 215 /* offset 0x0050 */ 216 __le32 gpioctl; 217#define GPIO3_LED_SELECT 12 218#define GPIO3_INTERRUPT_ENABLE 11 219#define GPIO2_INTERRUPT_ENABLE 10 220#define GPIO1_INTERRUPT_ENABLE 9 221#define GPIO0_INTERRUPT_ENABLE 8 222#define GPIO3_OUTPUT_ENABLE 7 223#define GPIO2_OUTPUT_ENABLE 6 224#define GPIO1_OUTPUT_ENABLE 5 225#define GPIO0_OUTPUT_ENABLE 4 226#define GPIO3_DATA 3 227#define GPIO2_DATA 2 228#define GPIO1_DATA 1 229#define GPIO0_DATA 0 230 __le32 gpiostat; 231#define GPIO3_INTERRUPT 3 232#define GPIO2_INTERRUPT 2 233#define GPIO1_INTERRUPT 1 234#define GPIO0_INTERRUPT 0 235} __packed; 236 237/* usb control, BAR0 + 0x0080 */ 238struct net2280_usb_regs { 239 /* offset 0x0080 */ 240 __le32 stdrsp; 241#define STALL_UNSUPPORTED_REQUESTS 31 242#define SET_TEST_MODE 16 243#define GET_OTHER_SPEED_CONFIGURATION 15 244#define GET_DEVICE_QUALIFIER 14 245#define SET_ADDRESS 13 246#define ENDPOINT_SET_CLEAR_HALT 12 247#define DEVICE_SET_CLEAR_DEVICE_REMOTE_WAKEUP 11 248#define GET_STRING_DESCRIPTOR_2 10 249#define GET_STRING_DESCRIPTOR_1 9 250#define GET_STRING_DESCRIPTOR_0 8 251#define GET_SET_INTERFACE 6 252#define GET_SET_CONFIGURATION 5 253#define GET_CONFIGURATION_DESCRIPTOR 4 254#define GET_DEVICE_DESCRIPTOR 3 255#define GET_ENDPOINT_STATUS 2 256#define GET_INTERFACE_STATUS 1 257#define GET_DEVICE_STATUS 0 258 __le32 prodvendid; 259#define PRODUCT_ID 16 260#define VENDOR_ID 0 261 __le32 relnum; 262 __le32 usbctl; 263#define SERIAL_NUMBER_INDEX 16 264#define PRODUCT_ID_STRING_ENABLE 13 265#define VENDOR_ID_STRING_ENABLE 12 266#define USB_ROOT_PORT_WAKEUP_ENABLE 11 267#define VBUS_PIN 10 268#define TIMED_DISCONNECT 9 269#define SUSPEND_IMMEDIATELY 7 270#define SELF_POWERED_USB_DEVICE 6 271#define REMOTE_WAKEUP_SUPPORT 5 272#define PME_POLARITY 4 273#define USB_DETECT_ENABLE 3 274#define PME_WAKEUP_ENABLE 2 275#define DEVICE_REMOTE_WAKEUP_ENABLE 1 276#define SELF_POWERED_STATUS 0 277 /* offset 0x0090 */ 278 __le32 usbstat; 279#define HIGH_SPEED 7 280#define FULL_SPEED 6 281#define GENERATE_RESUME 5 282#define GENERATE_DEVICE_REMOTE_WAKEUP 4 283 __le32 xcvrdiag; 284#define FORCE_HIGH_SPEED_MODE 31 285#define FORCE_FULL_SPEED_MODE 30 286#define USB_TEST_MODE 24 287#define LINE_STATE 16 288#define TRANSCEIVER_OPERATION_MODE 2 289#define TRANSCEIVER_SELECT 1 290#define TERMINATION_SELECT 0 291 __le32 setup0123; 292 __le32 setup4567; 293 /* offset 0x0090 */ 294 u32 _unused0; 295 __le32 ouraddr; 296#define FORCE_IMMEDIATE 7 297#define OUR_USB_ADDRESS 0 298 __le32 ourconfig; 299} __packed; 300 301/* pci control, BAR0 + 0x0100 */ 302struct net2280_pci_regs { 303 /* offset 0x0100 */ 304 __le32 pcimstctl; 305#define PCI_ARBITER_PARK_SELECT 13 306#define PCI_MULTI LEVEL_ARBITER 12 307#define PCI_RETRY_ABORT_ENABLE 11 308#define DMA_MEMORY_WRITE_AND_INVALIDATE_ENABLE 10 309#define DMA_READ_MULTIPLE_ENABLE 9 310#define DMA_READ_LINE_ENABLE 8 311#define PCI_MASTER_COMMAND_SELECT 6 312#define MEM_READ_OR_WRITE 0 313#define IO_READ_OR_WRITE 1 314#define CFG_READ_OR_WRITE 2 315#define PCI_MASTER_START 5 316#define PCI_MASTER_READ_WRITE 4 317#define PCI_MASTER_WRITE 0 318#define PCI_MASTER_READ 1 319#define PCI_MASTER_BYTE_WRITE_ENABLES 0 320 __le32 pcimstaddr; 321 __le32 pcimstdata; 322 __le32 pcimststat; 323#define PCI_ARBITER_CLEAR 2 324#define PCI_EXTERNAL_ARBITER 1 325#define PCI_HOST_MODE 0 326} __packed; 327 328/* dma control, BAR0 + 0x0180 ... array of four structs like this, 329 * for channels 0..3. see also struct net2280_dma: descriptor 330 * that can be loaded into some of these registers. 331 */ 332struct net2280_dma_regs { /* [11.7] */ 333 /* offset 0x0180, 0x01a0, 0x01c0, 0x01e0, */ 334 __le32 dmactl; 335#define DMA_SCATTER_GATHER_DONE_INTERRUPT_ENABLE 25 336#define DMA_CLEAR_COUNT_ENABLE 21 337#define DESCRIPTOR_POLLING_RATE 19 338#define POLL_CONTINUOUS 0 339#define POLL_1_USEC 1 340#define POLL_100_USEC 2 341#define POLL_1_MSEC 3 342#define DMA_VALID_BIT_POLLING_ENABLE 18 343#define DMA_VALID_BIT_ENABLE 17 344#define DMA_SCATTER_GATHER_ENABLE 16 345#define DMA_OUT_AUTO_START_ENABLE 4 346#define DMA_PREEMPT_ENABLE 3 347#define DMA_FIFO_VALIDATE 2 348#define DMA_ENABLE 1 349#define DMA_ADDRESS_HOLD 0 350 __le32 dmastat; 351#define DMA_SCATTER_GATHER_DONE_INTERRUPT 25 352#define DMA_TRANSACTION_DONE_INTERRUPT 24 353#define DMA_ABORT 1 354#define DMA_START 0 355 u32 _unused0[2]; 356 /* offset 0x0190, 0x01b0, 0x01d0, 0x01f0, */ 357 __le32 dmacount; 358#define VALID_BIT 31 359#define DMA_DIRECTION 30 360#define DMA_DONE_INTERRUPT_ENABLE 29 361#define END_OF_CHAIN 28 362#define DMA_BYTE_COUNT_MASK ((1<<24)-1) 363#define DMA_BYTE_COUNT 0 364 __le32 dmaaddr; 365 __le32 dmadesc; 366 u32 _unused1; 367} __packed; 368 369/* dedicated endpoint registers, BAR0 + 0x0200 */ 370 371struct net2280_dep_regs { /* [11.8] */ 372 /* offset 0x0200, 0x0210, 0x220, 0x230, 0x240 */ 373 __le32 dep_cfg; 374 /* offset 0x0204, 0x0214, 0x224, 0x234, 0x244 */ 375 __le32 dep_rsp; 376 u32 _unused[2]; 377} __packed; 378 379/* configurable endpoint registers, BAR0 + 0x0300 ... array of seven structs 380 * like this, for ep0 then the configurable endpoints A..F 381 * ep0 reserved for control; E and F have only 64 bytes of fifo 382 */ 383struct net2280_ep_regs { /* [11.9] */ 384 /* offset 0x0300, 0x0320, 0x0340, 0x0360, 0x0380, 0x03a0, 0x03c0 */ 385 __le32 ep_cfg; 386#define ENDPOINT_BYTE_COUNT 16 387#define ENDPOINT_ENABLE 10 388#define ENDPOINT_TYPE 8 389#define ENDPOINT_DIRECTION 7 390#define ENDPOINT_NUMBER 0 391 __le32 ep_rsp; 392#define SET_NAK_OUT_PACKETS 15 393#define SET_EP_HIDE_STATUS_PHASE 14 394#define SET_EP_FORCE_CRC_ERROR 13 395#define SET_INTERRUPT_MODE 12 396#define SET_CONTROL_STATUS_PHASE_HANDSHAKE 11 397#define SET_NAK_OUT_PACKETS_MODE 10 398#define SET_ENDPOINT_TOGGLE 9 399#define SET_ENDPOINT_HALT 8 400#define CLEAR_NAK_OUT_PACKETS 7 401#define CLEAR_EP_HIDE_STATUS_PHASE 6 402#define CLEAR_EP_FORCE_CRC_ERROR 5 403#define CLEAR_INTERRUPT_MODE 4 404#define CLEAR_CONTROL_STATUS_PHASE_HANDSHAKE 3 405#define CLEAR_NAK_OUT_PACKETS_MODE 2 406#define CLEAR_ENDPOINT_TOGGLE 1 407#define CLEAR_ENDPOINT_HALT 0 408 __le32 ep_irqenb; 409#define SHORT_PACKET_OUT_DONE_INTERRUPT_ENABLE 6 410#define SHORT_PACKET_TRANSFERRED_INTERRUPT_ENABLE 5 411#define DATA_PACKET_RECEIVED_INTERRUPT_ENABLE 3 412#define DATA_PACKET_TRANSMITTED_INTERRUPT_ENABLE 2 413#define DATA_OUT_PING_TOKEN_INTERRUPT_ENABLE 1 414#define DATA_IN_TOKEN_INTERRUPT_ENABLE 0 415 __le32 ep_stat; 416#define FIFO_VALID_COUNT 24 417#define HIGH_BANDWIDTH_OUT_TRANSACTION_PID 22 418#define TIMEOUT 21 419#define USB_STALL_SENT 20 420#define USB_IN_NAK_SENT 19 421#define USB_IN_ACK_RCVD 18 422#define USB_OUT_PING_NAK_SENT 17 423#define USB_OUT_ACK_SENT 16 424#define FIFO_OVERFLOW 13 425#define FIFO_UNDERFLOW 12 426#define FIFO_FULL 11 427#define FIFO_EMPTY 10 428#define FIFO_FLUSH 9 429#define SHORT_PACKET_OUT_DONE_INTERRUPT 6 430#define SHORT_PACKET_TRANSFERRED_INTERRUPT 5 431#define NAK_OUT_PACKETS 4 432#define DATA_PACKET_RECEIVED_INTERRUPT 3 433#define DATA_PACKET_TRANSMITTED_INTERRUPT 2 434#define DATA_OUT_PING_TOKEN_INTERRUPT 1 435#define DATA_IN_TOKEN_INTERRUPT 0 436 /* offset 0x0310, 0x0330, 0x0350, 0x0370, 0x0390, 0x03b0, 0x03d0 */ 437 __le32 ep_avail; 438 __le32 ep_data; 439 u32 _unused0[2]; 440} __packed; 441 442struct net2280_reg_write { 443 __le16 port; 444 __le32 addr; 445 __le32 val; 446} __packed; 447 448struct net2280_reg_read { 449 __le16 port; 450 __le32 addr; 451} __packed; 452#endif /* NET2280_H */ 453