1/* 2 * Copyright (C) 2004 Red Hat 3 * Copyright (C) 2007 Bartlomiej Zolnierkiewicz 4 * 5 * May be copied or modified under the terms of the GNU General Public License 6 * Based in part on the ITE vendor provided SCSI driver. 7 * 8 * Documentation: 9 * Datasheet is freely available, some other documents under NDA. 10 * 11 * The ITE8212 isn't exactly a standard IDE controller. It has two 12 * modes. In pass through mode then it is an IDE controller. In its smart 13 * mode its actually quite a capable hardware raid controller disguised 14 * as an IDE controller. Smart mode only understands DMA read/write and 15 * identify, none of the fancier commands apply. The IT8211 is identical 16 * in other respects but lacks the raid mode. 17 * 18 * Errata: 19 * o Rev 0x10 also requires master/slave hold the same DMA timings and 20 * cannot do ATAPI MWDMA. 21 * o The identify data for raid volumes lacks CHS info (technically ok) 22 * but also fails to set the LBA28 and other bits. We fix these in 23 * the IDE probe quirk code. 24 * o If you write LBA48 sized I/O's (ie > 256 sector) in smart mode 25 * raid then the controller firmware dies 26 * o Smart mode without RAID doesn't clear all the necessary identify 27 * bits to reduce the command set to the one used 28 * 29 * This has a few impacts on the driver 30 * - In pass through mode we do all the work you would expect 31 * - In smart mode the clocking set up is done by the controller generally 32 * but we must watch the other limits and filter. 33 * - There are a few extra vendor commands that actually talk to the 34 * controller but only work PIO with no IRQ. 35 * 36 * Vendor areas of the identify block in smart mode are used for the 37 * timing and policy set up. Each HDD in raid mode also has a serial 38 * block on the disk. The hardware extra commands are get/set chip status, 39 * rebuild, get rebuild status. 40 * 41 * In Linux the driver supports pass through mode as if the device was 42 * just another IDE controller. If the smart mode is running then 43 * volumes are managed by the controller firmware and each IDE "disk" 44 * is a raid volume. Even more cute - the controller can do automated 45 * hotplug and rebuild. 46 * 47 * The pass through controller itself is a little demented. It has a 48 * flaw that it has a single set of PIO/MWDMA timings per channel so 49 * non UDMA devices restrict each others performance. It also has a 50 * single clock source per channel so mixed UDMA100/133 performance 51 * isn't perfect and we have to pick a clock. Thankfully none of this 52 * matters in smart mode. ATAPI DMA is not currently supported. 53 * 54 * It seems the smart mode is a win for RAID1/RAID10 but otherwise not. 55 * 56 * TODO 57 * - ATAPI UDMA is ok but not MWDMA it seems 58 * - RAID configuration ioctls 59 * - Move to libata once it grows up 60 */ 61 62#include <linux/types.h> 63#include <linux/module.h> 64#include <linux/slab.h> 65#include <linux/pci.h> 66#include <linux/ide.h> 67#include <linux/init.h> 68 69#define DRV_NAME "it821x" 70 71#define QUIRK_VORTEX86 1 72 73struct it821x_dev 74{ 75 unsigned int smart:1, /* Are we in smart raid mode */ 76 timing10:1; /* Rev 0x10 */ 77 u8 clock_mode; /* 0, ATA_50 or ATA_66 */ 78 u8 want[2][2]; /* Mode/Pri log for master slave */ 79 /* We need these for switching the clock when DMA goes on/off 80 The high byte is the 66Mhz timing */ 81 u16 pio[2]; /* Cached PIO values */ 82 u16 mwdma[2]; /* Cached MWDMA values */ 83 u16 udma[2]; /* Cached UDMA values (per drive) */ 84 u16 quirks; 85}; 86 87#define ATA_66 0 88#define ATA_50 1 89#define ATA_ANY 2 90 91#define UDMA_OFF 0 92#define MWDMA_OFF 0 93 94/* 95 * We allow users to force the card into non raid mode without 96 * flashing the alternative BIOS. This is also necessary right now 97 * for embedded platforms that cannot run a PC BIOS but are using this 98 * device. 99 */ 100 101static int it8212_noraid; 102 103/** 104 * it821x_program - program the PIO/MWDMA registers 105 * @drive: drive to tune 106 * @timing: timing info 107 * 108 * Program the PIO/MWDMA timing for this channel according to the 109 * current clock. 110 */ 111 112static void it821x_program(ide_drive_t *drive, u16 timing) 113{ 114 ide_hwif_t *hwif = drive->hwif; 115 struct pci_dev *dev = to_pci_dev(hwif->dev); 116 struct it821x_dev *itdev = ide_get_hwifdata(hwif); 117 int channel = hwif->channel; 118 u8 conf; 119 120 /* Program PIO/MWDMA timing bits */ 121 if(itdev->clock_mode == ATA_66) 122 conf = timing >> 8; 123 else 124 conf = timing & 0xFF; 125 126 pci_write_config_byte(dev, 0x54 + 4 * channel, conf); 127} 128 129/** 130 * it821x_program_udma - program the UDMA registers 131 * @drive: drive to tune 132 * @timing: timing info 133 * 134 * Program the UDMA timing for this drive according to the 135 * current clock. 136 */ 137 138static void it821x_program_udma(ide_drive_t *drive, u16 timing) 139{ 140 ide_hwif_t *hwif = drive->hwif; 141 struct pci_dev *dev = to_pci_dev(hwif->dev); 142 struct it821x_dev *itdev = ide_get_hwifdata(hwif); 143 int channel = hwif->channel; 144 u8 unit = drive->dn & 1, conf; 145 146 /* Program UDMA timing bits */ 147 if(itdev->clock_mode == ATA_66) 148 conf = timing >> 8; 149 else 150 conf = timing & 0xFF; 151 152 if (itdev->timing10 == 0) 153 pci_write_config_byte(dev, 0x56 + 4 * channel + unit, conf); 154 else { 155 pci_write_config_byte(dev, 0x56 + 4 * channel, conf); 156 pci_write_config_byte(dev, 0x56 + 4 * channel + 1, conf); 157 } 158} 159 160/** 161 * it821x_clock_strategy 162 * @drive: drive to set up 163 * 164 * Select between the 50 and 66Mhz base clocks to get the best 165 * results for this interface. 166 */ 167 168static void it821x_clock_strategy(ide_drive_t *drive) 169{ 170 ide_hwif_t *hwif = drive->hwif; 171 struct pci_dev *dev = to_pci_dev(hwif->dev); 172 struct it821x_dev *itdev = ide_get_hwifdata(hwif); 173 ide_drive_t *pair = ide_get_pair_dev(drive); 174 int clock, altclock, sel = 0; 175 u8 unit = drive->dn & 1, v; 176 177 if(itdev->want[0][0] > itdev->want[1][0]) { 178 clock = itdev->want[0][1]; 179 altclock = itdev->want[1][1]; 180 } else { 181 clock = itdev->want[1][1]; 182 altclock = itdev->want[0][1]; 183 } 184 185 /* 186 * if both clocks can be used for the mode with the higher priority 187 * use the clock needed by the mode with the lower priority 188 */ 189 if (clock == ATA_ANY) 190 clock = altclock; 191 192 /* Nobody cares - keep the same clock */ 193 if(clock == ATA_ANY) 194 return; 195 /* No change */ 196 if(clock == itdev->clock_mode) 197 return; 198 199 /* Load this into the controller ? */ 200 if(clock == ATA_66) 201 itdev->clock_mode = ATA_66; 202 else { 203 itdev->clock_mode = ATA_50; 204 sel = 1; 205 } 206 207 pci_read_config_byte(dev, 0x50, &v); 208 v &= ~(1 << (1 + hwif->channel)); 209 v |= sel << (1 + hwif->channel); 210 pci_write_config_byte(dev, 0x50, v); 211 212 /* 213 * Reprogram the UDMA/PIO of the pair drive for the switch 214 * MWDMA will be dealt with by the dma switcher 215 */ 216 if(pair && itdev->udma[1-unit] != UDMA_OFF) { 217 it821x_program_udma(pair, itdev->udma[1-unit]); 218 it821x_program(pair, itdev->pio[1-unit]); 219 } 220 /* 221 * Reprogram the UDMA/PIO of our drive for the switch. 222 * MWDMA will be dealt with by the dma switcher 223 */ 224 if(itdev->udma[unit] != UDMA_OFF) { 225 it821x_program_udma(drive, itdev->udma[unit]); 226 it821x_program(drive, itdev->pio[unit]); 227 } 228} 229 230/** 231 * it821x_set_pio_mode - set host controller for PIO mode 232 * @hwif: port 233 * @drive: drive 234 * 235 * Tune the host to the desired PIO mode taking into the consideration 236 * the maximum PIO mode supported by the other device on the cable. 237 */ 238 239static void it821x_set_pio_mode(ide_hwif_t *hwif, ide_drive_t *drive) 240{ 241 struct it821x_dev *itdev = ide_get_hwifdata(hwif); 242 ide_drive_t *pair = ide_get_pair_dev(drive); 243 const u8 pio = drive->pio_mode - XFER_PIO_0; 244 u8 unit = drive->dn & 1, set_pio = pio; 245 246 /* Spec says 89 ref driver uses 88 */ 247 static u16 pio_timings[]= { 0xAA88, 0xA382, 0xA181, 0x3332, 0x3121 }; 248 static u8 pio_want[] = { ATA_66, ATA_66, ATA_66, ATA_66, ATA_ANY }; 249 250 /* 251 * Compute the best PIO mode we can for a given device. We must 252 * pick a speed that does not cause problems with the other device 253 * on the cable. 254 */ 255 if (pair) { 256 u8 pair_pio = pair->pio_mode - XFER_PIO_0; 257 /* trim PIO to the slowest of the master/slave */ 258 if (pair_pio < set_pio) 259 set_pio = pair_pio; 260 } 261 262 /* We prefer 66Mhz clock for PIO 0-3, don't care for PIO4 */ 263 itdev->want[unit][1] = pio_want[set_pio]; 264 itdev->want[unit][0] = 1; /* PIO is lowest priority */ 265 itdev->pio[unit] = pio_timings[set_pio]; 266 it821x_clock_strategy(drive); 267 it821x_program(drive, itdev->pio[unit]); 268} 269 270/** 271 * it821x_tune_mwdma - tune a channel for MWDMA 272 * @drive: drive to set up 273 * @mode_wanted: the target operating mode 274 * 275 * Load the timing settings for this device mode into the 276 * controller when doing MWDMA in pass through mode. The caller 277 * must manage the whole lack of per device MWDMA/PIO timings and 278 * the shared MWDMA/PIO timing register. 279 */ 280 281static void it821x_tune_mwdma(ide_drive_t *drive, u8 mode_wanted) 282{ 283 ide_hwif_t *hwif = drive->hwif; 284 struct pci_dev *dev = to_pci_dev(hwif->dev); 285 struct it821x_dev *itdev = (void *)ide_get_hwifdata(hwif); 286 u8 unit = drive->dn & 1, channel = hwif->channel, conf; 287 288 static u16 dma[] = { 0x8866, 0x3222, 0x3121 }; 289 static u8 mwdma_want[] = { ATA_ANY, ATA_66, ATA_ANY }; 290 291 itdev->want[unit][1] = mwdma_want[mode_wanted]; 292 itdev->want[unit][0] = 2; /* MWDMA is low priority */ 293 itdev->mwdma[unit] = dma[mode_wanted]; 294 itdev->udma[unit] = UDMA_OFF; 295 296 /* UDMA bits off - Revision 0x10 do them in pairs */ 297 pci_read_config_byte(dev, 0x50, &conf); 298 if (itdev->timing10) 299 conf |= channel ? 0x60: 0x18; 300 else 301 conf |= 1 << (3 + 2 * channel + unit); 302 pci_write_config_byte(dev, 0x50, conf); 303 304 it821x_clock_strategy(drive); 305 /* it821x_program(drive, itdev->mwdma[unit]); */ 306} 307 308/** 309 * it821x_tune_udma - tune a channel for UDMA 310 * @drive: drive to set up 311 * @mode_wanted: the target operating mode 312 * 313 * Load the timing settings for this device mode into the 314 * controller when doing UDMA modes in pass through. 315 */ 316 317static void it821x_tune_udma(ide_drive_t *drive, u8 mode_wanted) 318{ 319 ide_hwif_t *hwif = drive->hwif; 320 struct pci_dev *dev = to_pci_dev(hwif->dev); 321 struct it821x_dev *itdev = ide_get_hwifdata(hwif); 322 u8 unit = drive->dn & 1, channel = hwif->channel, conf; 323 324 static u16 udma[] = { 0x4433, 0x4231, 0x3121, 0x2121, 0x1111, 0x2211, 0x1111 }; 325 static u8 udma_want[] = { ATA_ANY, ATA_50, ATA_ANY, ATA_66, ATA_66, ATA_50, ATA_66 }; 326 327 itdev->want[unit][1] = udma_want[mode_wanted]; 328 itdev->want[unit][0] = 3; /* UDMA is high priority */ 329 itdev->mwdma[unit] = MWDMA_OFF; 330 itdev->udma[unit] = udma[mode_wanted]; 331 if(mode_wanted >= 5) 332 itdev->udma[unit] |= 0x8080; /* UDMA 5/6 select on */ 333 334 /* UDMA on. Again revision 0x10 must do the pair */ 335 pci_read_config_byte(dev, 0x50, &conf); 336 if (itdev->timing10) 337 conf &= channel ? 0x9F: 0xE7; 338 else 339 conf &= ~ (1 << (3 + 2 * channel + unit)); 340 pci_write_config_byte(dev, 0x50, conf); 341 342 it821x_clock_strategy(drive); 343 it821x_program_udma(drive, itdev->udma[unit]); 344 345} 346 347 348static void it821x_dma_start(ide_drive_t *drive) 349{ 350 ide_hwif_t *hwif = drive->hwif; 351 struct it821x_dev *itdev = ide_get_hwifdata(hwif); 352 u8 unit = drive->dn & 1; 353 354 if(itdev->mwdma[unit] != MWDMA_OFF) 355 it821x_program(drive, itdev->mwdma[unit]); 356 else if(itdev->udma[unit] != UDMA_OFF && itdev->timing10) 357 it821x_program_udma(drive, itdev->udma[unit]); 358 ide_dma_start(drive); 359} 360 361/** 362 * it821x_dma_write - DMA hook 363 * @drive: drive for DMA stop 364 * 365 * The IT821x has a single timing register for MWDMA and for PIO 366 * operations. As we flip back and forth we have to reload the 367 * clock. 368 */ 369 370static int it821x_dma_end(ide_drive_t *drive) 371{ 372 ide_hwif_t *hwif = drive->hwif; 373 struct it821x_dev *itdev = ide_get_hwifdata(hwif); 374 int ret = ide_dma_end(drive); 375 u8 unit = drive->dn & 1; 376 377 if(itdev->mwdma[unit] != MWDMA_OFF) 378 it821x_program(drive, itdev->pio[unit]); 379 return ret; 380} 381 382/** 383 * it821x_set_dma_mode - set host controller for DMA mode 384 * @hwif: port 385 * @drive: drive 386 * 387 * Tune the ITE chipset for the desired DMA mode. 388 */ 389 390static void it821x_set_dma_mode(ide_hwif_t *hwif, ide_drive_t *drive) 391{ 392 const u8 speed = drive->dma_mode; 393 394 /* 395 * MWDMA tuning is really hard because our MWDMA and PIO 396 * timings are kept in the same place. We can switch in the 397 * host dma on/off callbacks. 398 */ 399 if (speed >= XFER_UDMA_0 && speed <= XFER_UDMA_6) 400 it821x_tune_udma(drive, speed - XFER_UDMA_0); 401 else if (speed >= XFER_MW_DMA_0 && speed <= XFER_MW_DMA_2) 402 it821x_tune_mwdma(drive, speed - XFER_MW_DMA_0); 403} 404 405/** 406 * it821x_cable_detect - cable detection 407 * @hwif: interface to check 408 * 409 * Check for the presence of an ATA66 capable cable on the 410 * interface. Problematic as it seems some cards don't have 411 * the needed logic onboard. 412 */ 413 414static u8 it821x_cable_detect(ide_hwif_t *hwif) 415{ 416 /* The reference driver also only does disk side */ 417 return ATA_CBL_PATA80; 418} 419 420 421static void it821x_quirkproc(ide_drive_t *drive) 422{ 423 struct it821x_dev *itdev = ide_get_hwifdata(drive->hwif); 424 u16 *id = drive->id; 425 426 if (!itdev->smart) { 427 /* 428 * If we are in pass through mode then not much 429 * needs to be done, but we do bother to clear the 430 * IRQ mask as we may well be in PIO (eg rev 0x10) 431 * for now and we know unmasking is safe on this chipset. 432 */ 433 drive->dev_flags |= IDE_DFLAG_UNMASK; 434 } else { 435 /* 436 * Perform fixups on smart mode. We need to "lose" some 437 * capabilities the firmware lacks but does not filter, and 438 * also patch up some capability bits that it forgets to set 439 * in RAID mode. 440 */ 441 442 /* Check for RAID v native */ 443 if (strstr((char *)&id[ATA_ID_PROD], 444 "Integrated Technology Express")) { 445 /* In raid mode the ident block is slightly buggy 446 We need to set the bits so that the IDE layer knows 447 LBA28. LBA48 and DMA ar valid */ 448 id[ATA_ID_CAPABILITY] |= (3 << 8); /* LBA28, DMA */ 449 id[ATA_ID_COMMAND_SET_2] |= 0x0400; /* LBA48 valid */ 450 id[ATA_ID_CFS_ENABLE_2] |= 0x0400; /* LBA48 on */ 451 /* Reporting logic */ 452 printk(KERN_INFO "%s: IT8212 %sRAID %d volume", 453 drive->name, id[147] ? "Bootable " : "", 454 id[ATA_ID_CSFO]); 455 if (id[ATA_ID_CSFO] != 1) 456 printk(KERN_CONT "(%dK stripe)", id[146]); 457 printk(KERN_CONT ".\n"); 458 } else { 459 /* Non RAID volume. Fixups to stop the core code 460 doing unsupported things */ 461 id[ATA_ID_FIELD_VALID] &= 3; 462 id[ATA_ID_QUEUE_DEPTH] = 0; 463 id[ATA_ID_COMMAND_SET_1] = 0; 464 id[ATA_ID_COMMAND_SET_2] &= 0xC400; 465 id[ATA_ID_CFSSE] &= 0xC000; 466 id[ATA_ID_CFS_ENABLE_1] = 0; 467 id[ATA_ID_CFS_ENABLE_2] &= 0xC400; 468 id[ATA_ID_CSF_DEFAULT] &= 0xC000; 469 id[127] = 0; 470 id[ATA_ID_DLF] = 0; 471 id[ATA_ID_CSFO] = 0; 472 id[ATA_ID_CFA_POWER] = 0; 473 printk(KERN_INFO "%s: Performing identify fixups.\n", 474 drive->name); 475 } 476 477 /* 478 * Set MWDMA0 mode as enabled/support - just to tell 479 * IDE core that DMA is supported (it821x hardware 480 * takes care of DMA mode programming). 481 */ 482 if (ata_id_has_dma(id)) { 483 id[ATA_ID_MWDMA_MODES] |= 0x0101; 484 drive->current_speed = XFER_MW_DMA_0; 485 } 486 } 487 488} 489 490static struct ide_dma_ops it821x_pass_through_dma_ops = { 491 .dma_host_set = ide_dma_host_set, 492 .dma_setup = ide_dma_setup, 493 .dma_start = it821x_dma_start, 494 .dma_end = it821x_dma_end, 495 .dma_test_irq = ide_dma_test_irq, 496 .dma_lost_irq = ide_dma_lost_irq, 497 .dma_timer_expiry = ide_dma_sff_timer_expiry, 498 .dma_sff_read_status = ide_dma_sff_read_status, 499}; 500 501/** 502 * init_hwif_it821x - set up hwif structs 503 * @hwif: interface to set up 504 * 505 * We do the basic set up of the interface structure. The IT8212 506 * requires several custom handlers so we override the default 507 * ide DMA handlers appropriately 508 */ 509 510static void __devinit init_hwif_it821x(ide_hwif_t *hwif) 511{ 512 struct pci_dev *dev = to_pci_dev(hwif->dev); 513 struct ide_host *host = pci_get_drvdata(dev); 514 struct it821x_dev *itdevs = host->host_priv; 515 struct it821x_dev *idev = itdevs + hwif->channel; 516 u8 conf; 517 518 ide_set_hwifdata(hwif, idev); 519 520 pci_read_config_byte(dev, 0x50, &conf); 521 if (conf & 1) { 522 idev->smart = 1; 523 hwif->host_flags |= IDE_HFLAG_NO_ATAPI_DMA; 524 /* Long I/O's although allowed in LBA48 space cause the 525 onboard firmware to enter the twighlight zone */ 526 hwif->rqsize = 256; 527 } 528 529 /* Pull the current clocks from 0x50 also */ 530 if (conf & (1 << (1 + hwif->channel))) 531 idev->clock_mode = ATA_50; 532 else 533 idev->clock_mode = ATA_66; 534 535 idev->want[0][1] = ATA_ANY; 536 idev->want[1][1] = ATA_ANY; 537 538 /* 539 * Not in the docs but according to the reference driver 540 * this is necessary. 541 */ 542 543 if (dev->revision == 0x10) { 544 idev->timing10 = 1; 545 hwif->host_flags |= IDE_HFLAG_NO_ATAPI_DMA; 546 if (idev->smart == 0) 547 printk(KERN_WARNING DRV_NAME " %s: revision 0x10, " 548 "workarounds activated\n", pci_name(dev)); 549 } 550 551 if (idev->smart == 0) { 552 /* MWDMA/PIO clock switching for pass through mode */ 553 hwif->dma_ops = &it821x_pass_through_dma_ops; 554 } else 555 hwif->host_flags |= IDE_HFLAG_NO_SET_MODE; 556 557 if (hwif->dma_base == 0) 558 return; 559 560 hwif->ultra_mask = ATA_UDMA6; 561 hwif->mwdma_mask = ATA_MWDMA2; 562 563 /* Vortex86SX quirk: prevent Ultra-DMA mode to fix BadCRC issue */ 564 if (idev->quirks & QUIRK_VORTEX86) { 565 if (dev->revision == 0x11) 566 hwif->ultra_mask = 0; 567 } 568} 569 570static void it8212_disable_raid(struct pci_dev *dev) 571{ 572 /* Reset local CPU, and set BIOS not ready */ 573 pci_write_config_byte(dev, 0x5E, 0x01); 574 575 /* Set to bypass mode, and reset PCI bus */ 576 pci_write_config_byte(dev, 0x50, 0x00); 577 pci_write_config_word(dev, PCI_COMMAND, 578 PCI_COMMAND_PARITY | PCI_COMMAND_IO | 579 PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER); 580 pci_write_config_word(dev, 0x40, 0xA0F3); 581 582 pci_write_config_dword(dev,0x4C, 0x02040204); 583 pci_write_config_byte(dev, 0x42, 0x36); 584 pci_write_config_byte(dev, PCI_LATENCY_TIMER, 0x20); 585} 586 587static int init_chipset_it821x(struct pci_dev *dev) 588{ 589 u8 conf; 590 static char *mode[2] = { "pass through", "smart" }; 591 592 /* Force the card into bypass mode if so requested */ 593 if (it8212_noraid) { 594 printk(KERN_INFO DRV_NAME " %s: forcing bypass mode\n", 595 pci_name(dev)); 596 it8212_disable_raid(dev); 597 } 598 pci_read_config_byte(dev, 0x50, &conf); 599 printk(KERN_INFO DRV_NAME " %s: controller in %s mode\n", 600 pci_name(dev), mode[conf & 1]); 601 return 0; 602} 603 604static const struct ide_port_ops it821x_port_ops = { 605 /* it821x_set_{pio,dma}_mode() are only used in pass-through mode */ 606 .set_pio_mode = it821x_set_pio_mode, 607 .set_dma_mode = it821x_set_dma_mode, 608 .quirkproc = it821x_quirkproc, 609 .cable_detect = it821x_cable_detect, 610}; 611 612static const struct ide_port_info it821x_chipset __devinitdata = { 613 .name = DRV_NAME, 614 .init_chipset = init_chipset_it821x, 615 .init_hwif = init_hwif_it821x, 616 .port_ops = &it821x_port_ops, 617 .pio_mask = ATA_PIO4, 618}; 619 620/** 621 * it821x_init_one - pci layer discovery entry 622 * @dev: PCI device 623 * @id: ident table entry 624 * 625 * Called by the PCI code when it finds an ITE821x controller. 626 * We then use the IDE PCI generic helper to do most of the work. 627 */ 628 629static int __devinit it821x_init_one(struct pci_dev *dev, const struct pci_device_id *id) 630{ 631 struct it821x_dev *itdevs; 632 int rc; 633 634 itdevs = kzalloc(2 * sizeof(*itdevs), GFP_KERNEL); 635 if (itdevs == NULL) { 636 printk(KERN_ERR DRV_NAME " %s: out of memory\n", pci_name(dev)); 637 return -ENOMEM; 638 } 639 640 itdevs->quirks = id->driver_data; 641 642 rc = ide_pci_init_one(dev, &it821x_chipset, itdevs); 643 if (rc) 644 kfree(itdevs); 645 646 return rc; 647} 648 649static void __devexit it821x_remove(struct pci_dev *dev) 650{ 651 struct ide_host *host = pci_get_drvdata(dev); 652 struct it821x_dev *itdevs = host->host_priv; 653 654 ide_pci_remove(dev); 655 kfree(itdevs); 656} 657 658static const struct pci_device_id it821x_pci_tbl[] = { 659 { PCI_VDEVICE(ITE, PCI_DEVICE_ID_ITE_8211), 0 }, 660 { PCI_VDEVICE(ITE, PCI_DEVICE_ID_ITE_8212), 0 }, 661 { PCI_VDEVICE(RDC, PCI_DEVICE_ID_RDC_D1010), QUIRK_VORTEX86 }, 662 { 0, }, 663}; 664 665MODULE_DEVICE_TABLE(pci, it821x_pci_tbl); 666 667static struct pci_driver it821x_pci_driver = { 668 .name = "ITE821x IDE", 669 .id_table = it821x_pci_tbl, 670 .probe = it821x_init_one, 671 .remove = __devexit_p(it821x_remove), 672 .suspend = ide_pci_suspend, 673 .resume = ide_pci_resume, 674}; 675 676static int __init it821x_ide_init(void) 677{ 678 return ide_pci_register_driver(&it821x_pci_driver); 679} 680 681static void __exit it821x_ide_exit(void) 682{ 683 pci_unregister_driver(&it821x_pci_driver); 684} 685 686module_init(it821x_ide_init); 687module_exit(it821x_ide_exit); 688 689module_param_named(noraid, it8212_noraid, int, S_IRUGO); 690MODULE_PARM_DESC(noraid, "Force card into bypass mode"); 691 692MODULE_AUTHOR("Alan Cox"); 693MODULE_DESCRIPTION("PCI driver module for the ITE 821x"); 694MODULE_LICENSE("GPL"); 695