1/* $NetBSD: czreg.h,v 1.4 2024/02/09 22:08:35 andvar Exp $ */ 2 3/*- 4 * Copyright (c) 2000 Zembu Labs, Inc. 5 * All rights reserved. 6 * 7 * Author: Jason R. Thorpe <thorpej@zembu.com> 8 * 9 * Redistribution and use in source and binary forms, with or without 10 * modification, are permitted provided that the following conditions 11 * are met: 12 * 1. Redistributions of source code must retain the above copyright 13 * notice, this list of conditions and the following disclaimer. 14 * 2. Redistributions in binary form must reproduce the above copyright 15 * notice, this list of conditions and the following disclaimer in the 16 * documentation and/or other materials provided with the distribution. 17 * 3. All advertising materials mentioning features or use of this software 18 * must display the following acknowledgement: 19 * This product includes software developed by Zembu Labs, Inc. 20 * 4. Neither the name of Zembu Labs nor the names of its employees may 21 * be used to endorse or promote products derived from this software 22 * without specific prior written permission. 23 * 24 * THIS SOFTWARE IS PROVIDED BY ZEMBU LABS, INC. ``AS IS'' AND ANY EXPRESS 25 * OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WAR- 26 * RANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DIS- 27 * CLAIMED. IN NO EVENT SHALL ZEMBU LABS BE LIABLE FOR ANY DIRECT, INDIRECT, 28 * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT 29 * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, 30 * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY 31 * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT 32 * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF 33 * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. 34 */ 35 36/* 37 * Register and firmware communication definitions for the Cyclades 38 * Z series of multi-port serial adapters. 39 */ 40 41/* 42 * The Cyclades-Z series is an intelligent multi-port serial controller 43 * comprised of: 44 * 45 * - PLX PCI9060ES PCI bus interface 46 * - Xilinx XC5204 FPGA 47 * - IDT R3052 MIPS CPU 48 * 49 * Communication is performed by modifying structures in board local 50 * RAM or in host RAM. We define offsets into these structures so 51 * that either access method may be used. 52 * 53 * The Cyclades-Z comes in three basic flavors: 54 * 55 * - Cyclades-8Zo rev 1 -- This is an older 8-port board with no 56 * FPGA. 57 * 58 * - Cyclades-8Zo rev 2 -- This is the newer 8-port board, which 59 * uses an octopus cable. 60 * 61 * - Cyclades-Ze -- This is the top-of-the-line of the Cyclades 62 * multiport serial controllers. It uses a SCSI-2 cable to 63 * connect the card to a rack-mountable serial expansion box 64 * (1U high). Each box has 16 RJ45 serial ports, and up to 65 * 4 boxes can be chained together, for a total of 64 ports. 66 * Up to 2 boxes can be used without an extra power supply. 67 * Boxes 3 and 4 require their own external power supply, 68 * otherwise the firmware will refuse to start (as it cannot 69 * communicate with the UARTs in the boxes). 70 * 71 * The 8Zo flavors have not been tested, tho the programming interface 72 * is identical (except for the firmware load phase of the 8Zo rev 1; 73 * no FPGA load is done in that case), so they should work. 74 */ 75 76/* 77 * PLX Local Address Base values for the board RAM and FPGA registers. 78 * 79 * These values are specific to the Cyclades-Z. 80 */ 81#define LOCAL_ADDR0_RAM (0x00000000 | LASBA_ENABLE) 82#define LOCAL_ADDR0_FPGA (0x14000000 | LASBA_ENABLE) 83 84/* 85 * PLX Mailbox0 values. 86 * 87 * These values are specific to the Cyclades-Z. 88 */ 89#define MAILBOX0_8Zo_V1 0 /* Cyclades-8Zo ver. 1 */ 90#define MAILBOX0_8Zo_V2 1 /* Cyclades-8Zo ver. 2 */ 91#define MAILBOX0_Ze_V1 2 /* Cyclades-Ze ver. 1 */ 92 93/* 94 * Bits in the PLX INIT_CTRL register. 95 * 96 * These values are specific to the Cyclades-Z. 97 */ 98#define CONTROL_FPGA_LOADED CONTROL_GPI 99 100/* 101 * FPGA registers on the 8Zo boards. 102 */ 103#define FPGA_ID 0x00 /* FPGA ID */ 104#define FPGA_VERSION 0x04 /* FPGA version */ 105#define FPGA_CPU_START 0x08 /* CPU start */ 106#define FPGA_CPU_STOP 0x0c /* CPU stop */ 107#define FPGA_MISC 0x10 /* Misc. register */ 108#define FPGA_IDT_MODE 0x14 /* IDT MIPS R3000 mode */ 109#define FPGA_UART_IRQ_STAT 0x18 /* UART interrupt status */ 110#define FPGA_CLEAR_TIMER0_IRQ 0x1c /* clear timer 0 interrupt */ 111#define FPGA_CLEAR_TIMER1_IRQ 0x20 /* clear timer 1 interrupt */ 112#define FPGA_CLEAR_TIMER2_IRQ 0x24 /* clear timer 3 interrupt */ 113#define FPGA_TEST 0x28 /* test register */ 114#define FPGA_TEST_COUNT 0x2c /* test count register */ 115#define FPGA_TIMER_SELECT 0x30 /* timer select */ 116#define FPGA_PR_UART_IRQ_STAT 0x34 /* prioritized UART interrupt status */ 117#define FPGA_RAM_WAIT_STATE 0x38 /* RAM wait state */ 118#define FPGA_UART_WAIT_STATE 0x3c /* UART wait state */ 119#define FPGA_TIMER_WAIT_STATE 0x40 /* timer wait state */ 120#define FPGA_ACK_WAIT_STATE 0x44 /* ACK wait state */ 121 122/* 123 * FPGA registers on the Ze boards. Note that the important registers 124 * (FPGA_ID, FPGA_VERSION, FPGA_CPU_START, FPGA_CPU_STOP) are all in the 125 * same place as on the 8Zo boards, and have the same meanings. 126 */ 127#define FPGA_ZE_ID 0x00 /* FPGA ID */ 128#define FPGA_ZE_VERSION 0x04 /* FPGA version */ 129#define FPGA_ZE_CPU_START 0x08 /* CPU start */ 130#define FPGA_ZE_CPU_STOP 0x0c /* CPU stop */ 131#define FPGA_ZE_CTRL 0x10 /* CPU control */ 132#define FPGA_ZE_ZBUS_WAIT 0x14 /* Z-Bus wait state */ 133#define FPGA_ZE_TIMER_DIV 0x18 /* timer divisor */ 134#define FPGA_ZE_TIMER_IRQ_ACK 0x1c /* timer interrupt ACK */ 135 136/* 137 * Values for FPGA ID. 138 */ 139#define FPGA_ID_8Zo_V1 0x95 /* Cyclades-8Zo ver. 1 */ 140#define FPGA_ID_8Zo_V2 0x84 /* Cyclades-8Zo ver. 2 */ 141#define FPGA_ID_Ze_V1 0x89 /* Cyclades-Ze ver. 1 */ 142 143/* 144 * Values for Cyclades-Ze timer divisor. 145 */ 146#define ZE_TIMER_DIV_1M 0x00 147#define ZE_TIMER_DIV_256K 0x01 148#define ZE_TIMER_DIV_128K 0x02 149#define ZE_TIMER_DIV_32K 0x03 150 151/* 152 * Firmware interface starts here. 153 * 154 * These values are valid for the following Cyclades-Z firmware: 155 * 156 * @(#) Copyright (c) Cyclades Corporation, 1996, 1999 157 * @(#) ZFIRM Cyclades-Z/PCI Firmware V_3.3.1 09/24/99 158 */ 159 160/* 161 * Structure of the firmware header. 162 */ 163#define ZFIRM_MAX_BLOCKS 16 /* max. # of firmware/FPGA blocks */ 164struct zfirm_header { 165 u_int8_t zfh_name[64]; 166 u_int8_t zfh_date[32]; 167 u_int8_t zfh_aux[32]; 168 u_int32_t zfh_nconfig; 169 u_int32_t zfh_configoff; 170 u_int32_t zfh_nblocks; 171 u_int32_t zfh_blockoff; 172 u_int32_t zfh_reserved[9]; 173} __packed; 174 175struct zfirm_config { 176 u_int8_t zfc_name[64]; 177 u_int32_t zfc_mailbox; 178 u_int32_t zfc_function; 179 u_int32_t zfc_nblocks; 180 u_int32_t zfc_blocklist[ZFIRM_MAX_BLOCKS]; 181} __packed; 182 183#define ZFC_FUNCTION_NORMAL 0 /* normal operation */ 184#define ZFC_FUNCTION_TEST 1 /* test mode operation */ 185 186struct zfirm_block { 187 u_int32_t zfb_type; 188 u_int32_t zfb_fileoff; 189 u_int32_t zfb_ramoff; 190 u_int32_t zfb_size; 191} __packed; 192 193#define ZFB_TYPE_FIRMWARE 0 /* MIPS firmware */ 194#define ZFB_TYPE_FPGA 1 /* FPGA code */ 195 196#define ZFIRM_MAX_CHANNELS 64 /* max. # channels per board */ 197 198/* 199 * Firmware ID structure, which the firmware sets up after it boots. 200 */ 201#define ZFIRM_SIG_OFF 0x00000180 /* offset of signature in board RAM */ 202#define ZFIRM_CTRLADDR_OFF 0x00000184 /* offset of offset of control 203 structure */ 204#define ZFIRM_SIG 0x5557465A /* ZFIRM signature */ 205#define ZFIRM_HLT 0x59505B5C /* Halt due to power problem */ 206#define ZFIRM_RST 0x56040674 /* Firmware reset */ 207 208/* 209 * The firmware control structures are made up of the following: 210 * 211 * BOARD CONTROL (64 bytes) 212 * CHANNEL CONTROL (96 bytes * ZFIRM_MAX_CHANNELS) 213 * BUFFER CONTROL (64 bytes * ZFIRM_MAX_CHANNELS) 214 */ 215 216#define ZFIRM_BRDCTL_SIZE 64 217#define ZFIRM_CHNCTL_SIZE 96 218#define ZFIRM_BUFCTL_SIZE 64 219 220#define ZFIRM_CHNCTL_OFF(chan, reg) \ 221 (ZFIRM_BRDCTL_SIZE + ((chan) * ZFIRM_CHNCTL_SIZE) + (reg)) 222#define ZFIRM_BUFCTL_OFF(chan, reg) \ 223 (ZFIRM_CHNCTL_OFF(ZFIRM_MAX_CHANNELS, 0) + \ 224 ((chan) * ZFIRM_BUFCTL_SIZE) + (reg)) 225 226/* 227 * Offsets in the BOARD CONTROL structure. 228 */ 229 /* static info provided by MIPS */ 230#define BRDCTL_NCHANNEL 0x00 /* number of channels */ 231#define BRDCTL_FWVERSION 0x04 /* firmware version */ 232 /* static info provided by driver */ 233#define BRDCTL_C_OS 0x08 /* operating system ID */ 234#define BRDCTL_DRVERSION 0x0c /* driver version */ 235 /* board control area */ 236#define BRDCTL_INACTIVITY 0x10 /* inactivity control */ 237 /* host to firmware commands */ 238#define BRDCTL_HCMD_CHANNEL 0x14 /* channel number */ 239#define BRDCTL_HCMD_PARAM 0x18 /* parameter */ 240 /* firmware to host commands */ 241#define BRDCTL_FWCMD_CHANNEL 0x1c /* channel number */ 242#define BRDCTL_FWCMD_PARAM 0x20 /* parameter */ 243#define BRDCTL_INT_QUEUE_OFF 0x24 /* offset to INT_QUEUE structure */ 244 245/* 246 * Offsets in the CHANNEL CONTROL structure. 247 */ 248#define CHNCTL_OP_MODE 0x00 /* operation mode */ 249#define CHNCTL_INTR_ENABLE 0x04 /* interrupt making for UART */ 250#define CHNCTL_SW_FLOW 0x08 /* SW flow control */ 251#define CHNCTL_FLOW_STATUS 0x0c /* output flow status */ 252#define CHNCTL_COMM_BAUD 0x10 /* baud rate -- numerically specified */ 253#define CHNCTL_COMM_PARITY 0x14 /* parity */ 254#define CHNCTL_COMM_DATA_L 0x18 /* data length/stop */ 255#define CHNCTL_COMM_FLAGS 0x1c /* other flags */ 256#define CHNCTL_HW_FLOW 0x20 /* HW flow control */ 257#define CHNCTL_RS_CONTROL 0x24 /* RS-232 outputs */ 258#define CHNCTL_RS_STATUS 0x28 /* RS-232 inputs */ 259#define CHNCTL_FLOW_XON 0x2c /* XON character */ 260#define CHNCTL_FLOW_XOFF 0x30 /* XOFF character */ 261#define CHNCTL_HW_OVERFLOW 0x34 /* HW overflow counter */ 262#define CHNCTL_SW_OVERFLOW 0x38 /* SW overflow counter */ 263#define CHNCTL_COMM_ERROR 0x3c /* frame/parity error counter */ 264#define CHNCTL_ICHAR 0x40 /* special interrupt character */ 265 266/* 267 * Offsets in the BUFFER CONTROL structure. 268 */ 269#define BUFCTL_FLAG_DMA 0x00 /* buffers are in Host memory */ 270#define BUFCTL_TX_BUFADDR 0x04 /* address of Tx buffer */ 271#define BUFCTL_TX_BUFSIZE 0x08 /* size of Tx buffer */ 272#define BUFCTL_TX_THRESHOLD 0x0c /* Tx low water mark */ 273#define BUFCTL_TX_GET 0x10 /* tail index Tx buf */ 274#define BUFCTL_TX_PUT 0x14 /* head index Tx buf */ 275#define BUFCTL_RX_BUFADDR 0x18 /* address of Rx buffer */ 276#define BUFCTL_RX_BUFSIZE 0x1c /* size of Rx buffer */ 277#define BUFCTL_RX_THRESHOLD 0x20 /* Rx high water mark */ 278#define BUFCTL_RX_GET 0x24 /* tail index Rx buf */ 279#define BUFCTL_RX_PUT 0x28 /* head index Rx buf */ 280 281/* Values for operating system ID (BOARD CONTROL) */ 282#define C_OS_SVR3 0x00000010 /* generic SVR3 */ 283#define C_OS_XENIX 0x00000011 /* SCO XENIX */ 284#define C_OS_SCO 0x00000012 /* SCO SVR3 */ 285#define C_OS_SVR4 0x00000020 /* generic SVR4 */ 286#define C_OS_UXWARE 0x00000021 /* UnixWare */ 287#define C_OS_LINUX 0x00000030 /* Linux */ 288#define C_OS_SOLARIS 0x00000040 /* Solaris */ 289#define C_OS_BSD 0x00000050 /* generic BSD */ 290#define C_OS_DOS 0x00000070 /* generic DOS */ 291#define C_OS_NT 0x00000080 /* Windows NT */ 292#define C_OS_OS2 0x00000090 /* IBM OS/2 */ 293#define C_OS_MACOS 0x000000a0 /* MacOS */ 294#define C_OS_AIX 0x000000b0 /* IBM AIX */ 295 296/* Values for op_mode (CHANNEL CONTROL) */ 297#define C_CH_DISABLE 0x00000000 /* channel is disabled */ 298#define C_CH_TXENABLE 0x00000001 /* channel Tx enabled */ 299#define C_CH_RXENABLE 0x00000002 /* channel Rx enabled */ 300#define C_CH_ENABLE 0x00000003 /* channel Tx/Rx enabled */ 301#define C_CH_LOOPBACK 0x00000004 /* Loopback mode */ 302 303/* Values for comm_parity (CHANNEL CONTROL) */ 304#define C_PR_NONE 0x00000000 /* None */ 305#define C_PR_ODD 0x00000001 /* Odd */ 306#define C_PR_EVEN 0x00000002 /* Even */ 307#define C_PR_MARK 0x00000004 /* Mark */ 308#define C_PR_SPACE 0x00000008 /* Space */ 309#define C_PR_PARITY 0x000000ff 310#define C_PR_DISCARD 0x00000100 /* discard char with 311 frame/parity error */ 312#define C_PR_IGNORE 0x00000200 /* ignore frame/par error */ 313 314/* Values for comm_data_l (CHANNEL CONTROL) */ 315#define C_DL_CS5 0x00000001 316#define C_DL_CS6 0x00000002 317#define C_DL_CS7 0x00000004 318#define C_DL_CS8 0x00000008 319#define C_DL_CS 0x0000000f 320#define C_DL_1STOP 0x00000010 321#define C_DL_15STOP 0x00000020 322#define C_DL_2STOP 0x00000040 323#define C_DL_STOP 0x000000f0 324 325/* Values for intr_enable (CHANNEL CONTROL) */ 326#define C_IN_DISABLE 0x00000000 /* zero, disable interrupts */ 327#define C_IN_TXBEMPTY 0x00000001 /* tx buffer empty */ 328#define C_IN_TXLOWWM 0x00000002 /* tx buffer below LWM */ 329#define C_IN_TXFEMPTY 0x00000004 /* tx buffer + FIFO + 330 shift reg. empty */ 331#define C_IN_RXHIWM 0x00000010 /* rx buffer above HWM */ 332#define C_IN_RXNNDT 0x00000020 /* rx no new data timeout */ 333#define C_IN_MDCD 0x00000100 /* modem DCD change */ 334#define C_IN_MDSR 0x00000200 /* modem DSR change */ 335#define C_IN_MRI 0x00000400 /* modem RI change */ 336#define C_IN_MCTS 0x00000800 /* modem CTS change */ 337#define C_IN_RXBRK 0x00001000 /* Break received */ 338#define C_IN_PR_ERROR 0x00002000 /* parity error */ 339#define C_IN_FR_ERROR 0x00004000 /* frame error */ 340#define C_IN_OVR_ERROR 0x00008000 /* overrun error */ 341#define C_IN_RXOFL 0x00010000 /* RX buffer overflow */ 342#define C_IN_IOCTLW 0x00020000 /* I/O control w/ wait */ 343#define C_IN_MRTS 0x00040000 /* modem RTS drop */ 344#define C_IN_ICHAR 0x00080000 /* special intr. char 345 received */ 346 347/* Values for flow control (CHANNEL CONTROL) */ 348#define C_FL_OXX 0x00000001 /* output Xon/Xoff flow 349 control */ 350#define C_FL_IXX 0x00000002 /* input Xon/Xoff flow 351 control */ 352#define C_FL_OIXANY 0x00000004 /* output Xon/Xoff (any xon) */ 353#define C_FL_SWFLOW 0x0000000f 354 355/* Values for flow status (CHANNEL CONTROL) */ 356#define C_FS_TXIDLE 0x00000000 /* no Tx data in the buffer 357 or UART */ 358#define C_FS_SENDING 0x00000001 /* UART is sending data */ 359#define C_FS_SWFLOW 0x00000002 /* Tx is stopped by received 360 Xoff */ 361 362/* Values for RS-232 signals (CHANNEL CONTROL) */ 363#define C_RS_PARAM 0x80000000 /* indicates presence of 364 parameter in IOCTL command */ 365#define C_RS_RTS 0x00000001 /* RTS */ 366#define C_RS_DTR 0x00000004 /* DTR */ 367#define C_RS_DCD 0x00000100 /* CD */ 368#define C_RS_DSR 0x00000200 /* DSR */ 369#define C_RS_RI 0x00000400 /* RI */ 370#define C_RS_CTS 0x00000800 /* CTS */ 371 372/* Commands Host <--> Board */ 373#define C_CM_RESET 0x01 /* resets/flushes buffers */ 374#define C_CM_IOCTL 0x02 /* re-reads CH_CTRL */ 375#define C_CM_IOCTLW 0x03 /* re-reads CH_CTRL, intr when done */ 376#define C_CM_IOCTLM 0x04 /* RS-232 outputs change */ 377#define C_CM_SENDXOFF 0x10 /* sends Xoff */ 378#define C_CM_SENDXON 0x11 /* sends Xon */ 379#define C_CM_CLFLOW 0x12 /* Clears flow control (resume) */ 380#define C_CM_SENDBRK 0x41 /* sends break */ 381#define C_CM_INTBACK 0x42 /* Interrupt back */ 382#define C_CM_SET_BREAK 0x43 /* Tx break on */ 383#define C_CM_CLR_BREAK 0x44 /* Tx break off */ 384#define C_CM_CMD_DONE 0x45 /* Previous command done */ 385#define C_CM_INTBACK2 0x46 /* Alternate Interrupt back */ 386#define C_CM_TINACT 0x51 /* sets inactivity detection */ 387#define C_CM_IRQ_ENBL 0x52 /* enables generation of interrupts */ 388#define C_CM_IRQ_DSBL 0x53 /* disables generation of interrupts */ 389#define C_CM_ACK_ENBL 0x54 /* enables acknowledged interrupt 390 mode */ 391#define C_CM_ACK_DSBL 0x55 /* disables acknowledged intr mode */ 392#define C_CM_FLUSH_RX 0x56 /* flushes Rx buffer */ 393#define C_CM_FLUSH_TX 0x57 /* flushes Tx buffer */ 394#define C_CM_Q_ENABLE 0x58 /* enables queue access from the 395 driver */ 396#define C_CM_Q_DISABLE 0x59 /* disables queue access from the 397 driver */ 398#define C_CM_TXBEMPTY 0x60 /* Tx buffer is empty */ 399#define C_CM_TXLOWWM 0x61 /* Tx buffer low water mark */ 400#define C_CM_RXHIWM 0x62 /* Rx buffer high water mark */ 401#define C_CM_RXNNDT 0x63 /* rx no new data timeout */ 402#define C_CM_TXFEMPTY 0x64 /* Tx buffer, FIFO and shift reg. 403 are empty */ 404#define C_CM_ICHAR 0x65 /* Special Interrupt Character 405 received */ 406#define C_CM_MDCD 0x70 /* modem DCD change */ 407#define C_CM_MDSR 0x71 /* modem DSR change */ 408#define C_CM_MRI 0x72 /* modem RI change */ 409#define C_CM_MCTS 0x73 /* modem CTS change */ 410#define C_CM_MRTS 0x74 /* modem RTS drop */ 411#define C_CM_RXBRK 0x84 /* Break received */ 412#define C_CM_PR_ERROR 0x85 /* Parity error */ 413#define C_CM_FR_ERROR 0x86 /* Frame error */ 414#define C_CM_OVR_ERROR 0x87 /* Overrun error */ 415#define C_CM_RXOFL 0x88 /* RX buffer overflow */ 416#define C_CM_CMDERROR 0x90 /* command error */ 417#define C_CM_FATAL 0x91 /* fatal error */ 418#define C_CM_HW_RESET 0x92 /* reset board */ 419