hdc9224.h revision 1.1
1/* $NetBSD: hdc9224.h,v 1.1 1996/07/20 18:55:12 ragge Exp $ */ 2/* 3 * Copyright (c) 1996 Ludd, University of Lule}, Sweden. 4 * All rights reserved. 5 * 6 * This code is derived from software contributed to Ludd by Bertram Barth. 7 * 8 * Redistribution and use in source and binary forms, with or without 9 * modification, are permitted provided that the following conditions 10 * are met: 11 * 1. Redistributions of source code must retain the above copyright 12 * notice, this list of conditions and the following disclaimer. 13 * 2. Redistributions in binary form must reproduce the above copyright 14 * notice, this list of conditions and the following disclaimer in the 15 * documentation and/or other materials provided with the distribution. 16 * 3. All advertising materials mentioning features or use of this software 17 * must display the following acknowledgement: 18 * This product includes software developed at Ludd, University of 19 * Lule}, Sweden and its contributors. 20 * 4. The name of the author may not be used to endorse or promote products 21 * derived from this software without specific prior written permission 22 * 23 * THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS'' AND ANY EXPRESS OR 24 * IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES 25 * OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. 26 * IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT, 27 * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT 28 * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, 29 * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY 30 * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT 31 * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF 32 * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. 33 */ 34 35 36 37struct hdc9224_DKCreg { 38 unsigned char dkc_reg; /* Disk Register Data Access Port (rw)*/ 39 unsigned char fill[3]; /* bytes are longword aligned */ 40 unsigned char dkc_cmd; /* Disk Controller Command Port (wo) */ 41#define dkc_stat dkc_cmd /* Interrupt Status Port (ro) */ 42}; 43 44/* 45 * definition of some commands (constant bits only, incomplete!) 46 */ 47#define DKC_CMD_RESET 0x00 /* terminate non-data-transfer cmds */ 48#define DKC_CMD_DRDESELECT 0x01 /* done when no drive is in use */ 49#define DKC_CMD_SETREGPTR 0x40 /* logically or-ed with reg-number */ 50#define DKC_CMD_DRSELECT 0x20 51#define DKC_CMD_DRSEL_HDD 0x24 /* select HDD, or-ed with unit-numb. */ 52#define DKC_CMD_DRSEL_RX33 0x28 /* or-ed with unit-number of RX33 */ 53#define DKC_CMD_DRSEL_RX50 0x2C /* or-ed with unit-number of RX50 */ 54#define DKC_CMD_RESTORE 0x02 55#define DKC_CMD_STEP 0x04 56#define DKC_CMD_STEPIN_FDD 0x04 /* one step inward for floppy */ 57#define DKC_CMD_STEPOUT_FDD 0x06 /* one step outward (toward cyl #0) */ 58#define DKC_CMD_POLLDRIVE 0x10 59#define DKC_CMD_SEEKREADID 0x50 60#define DKC_CMD_FORMATTRACK 0x60 61#define DKC_CMD_READTRACK 0x5A 62#define DKC_CMD_READPHYSICAL 0x58 63#define DKC_CMD_READLOGICAL 0x5C 64#define DKC_CMD_READ_HDD 0x5D /* read-logical, bypass=0, xfer=1 */ 65#define DKC_CMD_READ_RX33 0x5D /* ??? */ 66#define DKC_CMD_WRITEPHYSICAL 0x80 67#define DKC_CMD_WRITELOGICAL 0xC0 68#define DKC_CMD_WRITE_HDD 0xA0 /* bypass=0, ddmark=0 */ 69#define DKC_CMD_WRITE_RX33 0xA1 /* precompensation differs... */ 70#define DKC_CMD_WRITE_RX50 0xA4 71 72/* 73 * Definition of bits in the DKC_STAT register 74 */ 75#define DKC_ST_INTPEND (1<<7) /* interrupt pending */ 76#define DKC_ST_DMAREQ (1<<6) /* DMA request */ 77#define DKC_ST_DONE (1<<5) /* command done */ 78#define DKC_ST_TERMCOD (3<<3) /* termination code (see below) */ 79#define DKC_ST_RDYCHNG (1<<2) /* ready change */ 80#define DKC_ST_OVRUN (1<<1) /* overrun/underrun */ 81#define DKC_ST_BADSECT (1<<0) /* bad sector */ 82 83/* 84 * Definition of the termination codes 85 */ 86#define DKC_TC_SUCCESS (0<<3) /* Successful completion */ 87#define DKC_TC_RDIDERR (1<<3) /* Error in READ-ID sequence */ 88#define DKC_TC_VRFYERR (2<<3) /* Error in VERIFY sequence */ 89#define DKC_TC_DATAERR (3<<3) /* Error in DATA-TRANSFER seq. */ 90 91/* 92 * Definitions of delays neccessary for floppy-operation 93 */ 94#define DKC_DELAY_MOTOR 500 /* allow 500 ms to reach speed */ 95#define DKC_DELAY_SELECT 70 /* 70 ms for data-recovery-circuit */ 96#define DKC_DELAY_POSITION 59 /* 59 ms for RX33, 100 ms for RX50 */ 97#define DKC_DELAY_HEADSET 18 /* 18 ms when changing head-number */ 98 99/* 100 * The HDC9224 has 11/15(?) internal registers which are accessible via 101 * the Disk-Register-Data-Access-Port DKC_REG 102 */ 103struct hdc9224_UDCreg { /* internal disk controller registers */ 104 u_char udc_dma7; /* 0: DMA adress bits 0 - 7 */ 105 u_char udc_dma15; /* 1: DMA adress bits 8 - 15 */ 106 u_char udc_dma23; /* 2: DMA adress bits 16 - 23 */ 107 u_char udc_dsect; /* 3: desired/starting sector number */ 108#define udc_csect udc_dsect /* current sector number */ 109 u_char udc_dhead; /* 4: cyl-bits 8-10, desired head number */ 110#define udc_chead udc_dhead /* current head number */ 111 u_char udc_dcyl; /* 5: desired cylinder number */ 112#define udc_ccyl udc_dcyl /* current cylinder number */ 113 u_char udc_scnt; /* 6: sector count register */ 114 u_char udc_rtcnt; /* 7: retry count register */ 115 u_char udc_mode; /* 8: operation mode/chip status */ 116#define udc_cstat udc_mode /* chip status register */ 117 u_char udc_term; /* 9: termination conditions/drive status */ 118#define udc_dstat udc_term /* drive status register */ 119 u_char udc_data; /* 10: data */ 120}; 121 122/* 123 * Definition of bits in the Current-Head register 124 */ 125#define UDC_CH_BADSECT (1<<7) /* indicates a bad sector (if bypass=0) */ 126#define UDC_CH_CYLBITS (0x70) /* bits 10-8 of current cylinder number */ 127#define UDC_CH_HEADNO (0x0F) /* current head number */ 128 129/* 130 * Definition of bits in the Retry-Count register 131 */ 132#define UDC_RC_RTRYCNT (0xF0) /* 1's compl. in read-log, 0 all others */ 133#define UDC_RC_RXDISAB (1<<3) /* must/should be 0 for normal operation */ 134#define UDC_RC_INVRDY (1<<2) /* polarity of floppy-status, important! */ 135#define UDC_RC_MOTOR (1<<1) /* turn on floppy-motor, no effect on HDD */ 136#define UDC_RC_LOSPEED (1<<0) /* floppy-speed select, RX33: 0, RX50: 1 */ 137 138#define UDC_RC_HDD_READ 0xF2 /* 0x72 ??? */ 139#define UDC_RC_HDD_WRT 0xF2 /* 0xF0 ??? */ 140#define UDC_RC_RX33READ 0x76 /* enable retries when reading floppies */ 141#define UDC_RC_RX33WRT 0xF6 142#define UDC_RC_RX50READ 0x77 /* enable retries when reading floppies */ 143#define UDC_RC_RX50WRT 0xF7 144 145/* 146 * Definition of bits in the Operating-Mode register 147 */ 148#define UDC_MD_HDMODE (1<<7) /* must be 1 for all FDD and HDD */ 149#define UDC_MD_CHKCOD (3<<5) /* error-check: FDD/CRC: 0, HDD/ECC: 1 */ 150#define UDC_MD_DENS (1<<4) /* density select, must be 0 */ 151#define UDC_MD_UNUSED (1<<3) /* bit 3 is not used and must be 0 */ 152#define UDC_MD_SRATE (7<<0) /* seek step rate */ 153 154#define UDC_MD_HDD 0xC0 155#define UDC_MD_RX33 0x82 156#define UDC_MD_RX50 0x81 157 158/* 159 * Definition of bits in the Chip-Status register 160 */ 161#define UDC_CS_RETREQ (1<<7) /* retry required */ 162#define UDC_CS_ECCATT (1<<6) /* error correction attempted */ 163#define UDC_CS_ECCERR (1<<5) /* ECC/CRC error */ 164#define UDC_CS_DELDATA (1<<4) /* deleted data mark */ 165#define UDC_CS_SYNCERR (1<<3) /* synchronization error */ 166#define UDC_CS_COMPERR (1<<2) /* compare error */ 167#define UDC_CS_PRESDRV (0x3) /* present drive selected */ 168 169/* 170 * Definition of bits in the Termination-Conditions register 171 */ 172#define UDC_TC_CRCPRE (1<<7) /* CRC register preset, must be 1 */ 173#define UDC_TC_UNUSED (1<<6) /* bit 6 is not used and must be 0 */ 174#define UDC_TC_INTDONE (1<<5) /* interrupt on done */ 175#define UDC_TC_TDELDAT (1<<4) /* terminate on deleted data */ 176#define UDC_TC_TDSTAT3 (1<<3) /* terminate on drive status 3 change */ 177#define UDC_TC_TWPROT (1<<2) /* terminate on write-protect (FDD only) */ 178#define UDC_TC_INTRDCH (1<<1) /* interrupt on ready change (FDD only) */ 179#define UDC_TC_TWRFLT (1<<0) /* interrupt on write-fault (HDD only) */ 180 181#define UDC_TC_HDD 0xA5 /* 0xB5 ??? */ 182#define UDC_TC_FDD 0xA0 /* 0xAA ??? 0xB4 ??? */ 183 184/* 185 * Definition of bits in the Disk-Status register 186 */ 187#define UDC_DS_SELACK (1<<7) /* select acknowledge (harddisk only!) */ 188#define UDC_DS_INDEX (1<<6) /* index point */ 189#define UDC_DS_SKCOM (1<<5) /* seek complete */ 190#define UDC_DS_TRK00 (1<<4) /* track 0 */ 191#define UDC_DS_DSTAT3 (1<<3) /* drive status 3 (MBZ) */ 192#define UDC_DS_WRPROT (1<<2) /* write protect (floppy only!) */ 193#define UDC_DS_READY (1<<1) /* drive ready bit */ 194#define UDC_DS_WRFAULT (1<<0) /* write fault */ 195 196 197