sa11x0_sspreg.h revision 1.4
1/* $NetBSD: sa11x0_sspreg.h,v 1.4 2024/02/04 18:52:35 andvar Exp $ */ 2 3/*- 4 * Copyright (c) 2001, The NetBSD Foundation, Inc. All rights reserved. 5 * 6 * This code is derived from software contributed to The NetBSD Foundation 7 * by IWAMOTO Toshihiro. 8 * 9 * Redistribution and use in source and binary forms, with or without 10 * modification, are permitted provided that the following conditions 11 * are met: 12 * 1. Redistributions of source code must retain the above copyright 13 * notice, this list of conditions and the following disclaimer. 14 * 2. Redistributions in binary form must reproduce the above copyright 15 * notice, this list of conditions and the following disclaimer in the 16 * documentation and/or other materials provided with the distribution. 17 * 18 * THIS SOFTWARE IS PROVIDED BY THE NETBSD FOUNDATION, INC. AND CONTRIBUTORS 19 * ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED 20 * TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR 21 * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE FOUNDATION OR CONTRIBUTORS 22 * BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR 23 * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF 24 * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS 25 * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN 26 * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) 27 * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE 28 * POSSIBILITY OF SUCH DAMAGE. 29 */ 30 31/* SA11[01]0 integrated SSP (synchronous serial port) interface */ 32 33#define SASSP_FREQ (3686400 / 2) 34#define SASSPSPEED(b) (SACOM_FREQ / (b) - 1) 35 36/* size of I/O space */ 37#define SASSP_NPORTS 30 38 39#define SASSP_TXFIFOLEN 8 40#define SASSP_RXFIFOLEN 12 41 42/* SSP control register 0 */ 43#define SASSP_CR0 0x60 44#define CR0_DSS_MASK 0x000F /* Data size select */ 45#define CR0_FRF_MASK 0x0030 /* Frame format */ 46#define CR0_SSE 0x0080 /* SSP enable */ 47#define CR0_SCR_MASK 0xFF00 /* Serial clock rate */ 48 49/* SSP control register 1 */ 50#define SASSP_CR1 0x64 51#define CR1_RIE 0x01 /* Receive FIFO interrupt enable */ 52#define CR1_TIE 0x02 /* Transmit FIFO interrupt enable */ 53#define CR1_LBM 0x04 /* Loopback mode */ 54#define CR1_SPO 0x08 /* Serial clock polarity */ 55#define CR1_SPH 0x10 /* Serial clock phase */ 56#define CR1_ECS 0x20 /* External clock select */ 57 58/* SSP data register */ 59#define SASSP_DR 0x6C 60 61/* SSP status register */ 62#define SASSP_SR 0x74 63#define SR_TNF 0x02 /* Transmit FIFO not full */ 64#define SR_RNE 0x04 /* Receive FIFO not empty */ 65#define SR_BSY 0x08 /* SSP busy flag */ 66#define SR_TFS 0x10 /* Transmit FIFO service request */ 67#define SR_RFS 0x20 /* Receive FIFO service request */ 68#define SR_ROR 0x40 /* Receive FIFO overrun */ 69