nat-setup revision 1.1.1.1
1Configuring NAT on your network. 2================================ 3 4To start setting up NAT, we need to define which is your "internal" interface 5and which is your "external" interface. The "internal" interface is the 6network adapter connected to the network with private IP addresses which 7you need to change for communicating on the Internet. The "external" 8interface is configured with a valid internet address. 9 10For example, your internal interface might have an IP# of 10.1.1.1 and be 11connected to your ethernet, whilst your external interface might be a PPP 12connection with an IP number of 204.51.62.176. 13 14Thus your network might look like this: 15 16<Internal Network> 17 [pc] [pc] 18 | | 19+-+---------+------+ 20 | 21 [firewall] 22 | 23 | 24 Internet 25<External Network> 26 27 28Writing the map-rule. 29--------------------- 30When you're connected to the Internet, you will either have a block of IP 31addresses assigned to you, maybe several different blocks, or you use a 32single IP address, i.e. with dialup PPP. If you have a block of addresses 33assigned, these can be used to create either a 1:1 mapping (if you have 34only a few internal IP addresses) or N:1 mappings, where groups of internal 35addresses map to a single IP address and unless you have enough Internet 36addresses for a 1:1 mapping, you will want to do "portmapping" for TCP and 37UDP port numbers. 38 39For an N:1 situation, you might have: 40 41map ppp0 10.1.0.0/16 -> 209.23.1.5/32 portmap tcp/udp 10000:40000 42map ppp0 10.1.0.0/16 -> 209.23.1.5/32 portmap 43 44where if you had 16 addresses available, you could do: 45 46map ppp0 10.1.0.0/16 -> 209.23.1.0/28 portmap tcp/udp 10000:40000 47map ppp0 10.1.0.0/16 -> 209.23.1.0/28 portmap 48 49Or if you wanted to allocate subnets to each IP#, you might do: 50 51map ppp0 10.1.1.0/24 -> 209.23.1.2/32 portmap tcp/udp 10000:40000 52map ppp0 10.1.2.0/24 -> 209.23.1.3/32 portmap tcp/udp 10000:40000 53map ppp0 10.1.3.0/24 -> 209.23.1.4/32 portmap tcp/udp 10000:40000 54map ppp0 10.1.1.0/24 -> 209.23.1.2/32 portmap 55map ppp0 10.1.2.0/24 -> 209.23.1.3/32 portmap 56map ppp0 10.1.3.0/24 -> 209.23.1.4/32 portmap 57 58*** NOTE: NAT rules are used on a first-match basis only! 59 60 61Filtering with NAT. 62------------------- 63IP Filter will always translate addresses in a packet _BEFORE_ it checks its 64access list for inbound packets and translates addresses _AFTER_ it has 65checked the access control lists for outbound packets. 66 67For example (using the above NAT rules), if you wanted to prevent all hosts 68in the 10.1.2.0/24 subnet from using NAT, you might use the following rule 69with ipf: 70 71block out on ppp0 from 10.1.2.0/24 to any 72block in on ppp0 from any to 10.1.2.0/24 73 74and use these with ipnat: 75 76map ppp0 10.1.0.0/16 -> 209.23.1.0/28 portmap tcp/udp 10000:40000 77map ppp0 10.1.0.0/16 -> 209.23.1.0/28 portmap 78