1/*
2 * Copyright (C) 2016 Hans de Goede <hdegoede@redhat.com>
3 *
4 * This file is dual-licensed: you can use it either under the terms
5 * of the GPL or the X11 license, at your option. Note that this dual
6 * licensing only applies to this file, and not this project as a
7 * whole.
8 *
9 *  a) This file is free software; you can redistribute it and/or
10 *     modify it under the terms of the GNU General Public License as
11 *     published by the Free Software Foundation; either version 2 of the
12 *     License, or (at your option) any later version.
13 *
14 *     This file is distributed in the hope that it will be useful,
15 *     but WITHOUT ANY WARRANTY; without even the implied warranty of
16 *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
17 *     GNU General Public License for more details.
18 *
19 * Or, alternatively,
20 *
21 *  b) Permission is hereby granted, free of charge, to any person
22 *     obtaining a copy of this software and associated documentation
23 *     files (the "Software"), to deal in the Software without
24 *     restriction, including without limitation the rights to use,
25 *     copy, modify, merge, publish, distribute, sublicense, and/or
26 *     sell copies of the Software, and to permit persons to whom the
27 *     Software is furnished to do so, subject to the following
28 *     conditions:
29 *
30 *     The above copyright notice and this permission notice shall be
31 *     included in all copies or substantial portions of the Software.
32 *
33 *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
34 *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
35 *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
36 *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
37 *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
38 *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
39 *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
40 *     OTHER DEALINGS IN THE SOFTWARE.
41 */
42
43/dts-v1/;
44#include "sun8i-h3.dtsi"
45#include "sunxi-common-regulators.dtsi"
46
47#include <dt-bindings/gpio/gpio.h>
48#include <dt-bindings/input/input.h>
49
50/ {
51	model = "Xunlong Orange Pi Lite";
52	compatible = "xunlong,orangepi-lite", "allwinner,sun8i-h3";
53
54	aliases {
55		/* The H3 emac is not used so the wifi is ethernet0 */
56		ethernet0 = &rtl8189ftv;
57		serial0 = &uart0;
58	};
59
60	chosen {
61		stdout-path = "serial0:115200n8";
62	};
63
64	connector {
65		compatible = "hdmi-connector";
66		type = "a";
67
68		port {
69			hdmi_con_in: endpoint {
70				remote-endpoint = <&hdmi_out_con>;
71			};
72		};
73	};
74
75	leds {
76		compatible = "gpio-leds";
77
78		pwr_led {
79			label = "orangepi:green:pwr";
80			gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>;
81			default-state = "on";
82		};
83
84		status_led {
85			label = "orangepi:red:status";
86			gpios = <&pio 0 15 GPIO_ACTIVE_HIGH>;
87		};
88	};
89
90	gpio-keys {
91		compatible = "gpio-keys";
92
93		switch-4 {
94			label = "sw4";
95			linux,code = <BTN_0>;
96			gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
97		};
98	};
99};
100
101&de {
102	status = "okay";
103};
104
105&ehci1 {
106	status = "okay";
107};
108
109&ehci2 {
110	status = "okay";
111};
112
113&hdmi {
114	status = "okay";
115};
116
117&hdmi_out {
118	hdmi_out_con: endpoint {
119		remote-endpoint = <&hdmi_con_in>;
120	};
121};
122
123&ir {
124	pinctrl-names = "default";
125	pinctrl-0 = <&r_ir_rx_pin>;
126	status = "okay";
127};
128
129&mmc0 {
130	vmmc-supply = <&reg_vcc3v3>;
131	bus-width = <4>;
132	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
133	status = "okay";
134};
135
136&mmc1 {
137	vmmc-supply = <&reg_vcc3v3>;
138	bus-width = <4>;
139	non-removable;
140	status = "okay";
141
142	/*
143	 * Explicitly define the sdio device, so that we can add an ethernet
144	 * alias for it (which e.g. makes u-boot set a mac-address).
145	 */
146	rtl8189ftv: wifi@1 {
147		reg = <1>;
148	};
149};
150
151&ohci1 {
152	status = "okay";
153};
154
155&ohci2 {
156	status = "okay";
157};
158
159&uart0 {
160	pinctrl-names = "default";
161	pinctrl-0 = <&uart0_pa_pins>;
162	status = "okay";
163};
164
165&usbphy {
166	/* USB VBUS is always on */
167	status = "okay";
168};
169