1/* SPDX-License-Identifier: GPL-2.0 */
2/*
3 * usr/include/linux/lp.h c.1991-1992 James Wiegand
4 * many modifications copyright (C) 1992 Michael K. Johnson
5 * Interrupt support added 1993 Nigel Gamble
6 * Removed 8255 status defines from inside __KERNEL__ Marcelo Tosatti
7 */
8#ifndef _LINUX_LP_H
9#define _LINUX_LP_H
10
11
12#include <linux/wait.h>
13#include <linux/mutex.h>
14#include <uapi/linux/lp.h>
15
16/* Magic numbers for defining port-device mappings */
17#define LP_PARPORT_UNSPEC -4
18#define LP_PARPORT_AUTO -3
19#define LP_PARPORT_OFF -2
20#define LP_PARPORT_NONE -1
21
22#define LP_F(minor)	lp_table[(minor)].flags		/* flags for busy, etc. */
23#define LP_CHAR(minor)	lp_table[(minor)].chars		/* busy timeout */
24#define LP_TIME(minor)	lp_table[(minor)].time		/* wait time */
25#define LP_WAIT(minor)	lp_table[(minor)].wait		/* strobe wait */
26#define LP_IRQ(minor)	lp_table[(minor)].dev->port->irq /* interrupt # */
27					/* PARPORT_IRQ_NONE means polled */
28#ifdef LP_STATS
29#define LP_STAT(minor)	lp_table[(minor)].stats		/* statistics area */
30#endif
31#define LP_BUFFER_SIZE PAGE_SIZE
32
33#define LP_BASE(x)	lp_table[(x)].dev->port->base
34
35#ifdef LP_STATS
36struct lp_stats {
37	unsigned long chars;
38	unsigned long sleeps;
39	unsigned int maxrun;
40	unsigned int maxwait;
41	unsigned int meanwait;
42	unsigned int mdev;
43};
44#endif
45
46struct lp_struct {
47	struct pardevice *dev;
48	unsigned long flags;
49	unsigned int chars;
50	unsigned int time;
51	unsigned int wait;
52	char *lp_buffer;
53#ifdef LP_STATS
54	unsigned int lastcall;
55	unsigned int runchars;
56	struct lp_stats stats;
57#endif
58	wait_queue_head_t waitq;
59	unsigned int last_error;
60	struct mutex port_mutex;
61	wait_queue_head_t dataq;
62	long timeout;
63	unsigned int best_mode;
64	unsigned int current_mode;
65	unsigned long bits;
66};
67
68/*
69 * The following constants describe the various signals of the printer port
70 * hardware.  Note that the hardware inverts some signals and that some
71 * signals are active low.  An example is LP_STROBE, which must be programmed
72 * with 1 for being active and 0 for being inactive, because the strobe signal
73 * gets inverted, but it is also active low.
74 */
75
76
77/*
78 * defines for 8255 control port
79 * base + 2
80 * accessed with LP_C(minor)
81 */
82#define LP_PINTEN	0x10  /* high to read data in or-ed with data out */
83#define LP_PSELECP	0x08  /* inverted output, active low */
84#define LP_PINITP	0x04  /* unchanged output, active low */
85#define LP_PAUTOLF	0x02  /* inverted output, active low */
86#define LP_PSTROBE	0x01  /* short high output on raising edge */
87
88/*
89 * the value written to ports to test existence. PC-style ports will
90 * return the value written. AT-style ports will return 0. so why not
91 * make them the same ?
92 */
93#define LP_DUMMY	0x00
94
95/*
96 * This is the port delay time, in microseconds.
97 * It is used only in the lp_init() and lp_reset() routine.
98 */
99#define LP_DELAY 	50
100
101#endif
102