1// SPDX-License-Identifier: GPL-2.0-or-later 2/* 3 * Copyright (C) 2012 - 2014 Allwinner Tech 4 * Pan Nan <pannan@allwinnertech.com> 5 * 6 * Copyright (C) 2014 Maxime Ripard 7 * Maxime Ripard <maxime.ripard@free-electrons.com> 8 */ 9 10#include <linux/bitfield.h> 11#include <linux/clk.h> 12#include <linux/delay.h> 13#include <linux/device.h> 14#include <linux/interrupt.h> 15#include <linux/io.h> 16#include <linux/module.h> 17#include <linux/of.h> 18#include <linux/platform_device.h> 19#include <linux/pm_runtime.h> 20#include <linux/reset.h> 21#include <linux/dmaengine.h> 22 23#include <linux/spi/spi.h> 24 25#define SUN6I_AUTOSUSPEND_TIMEOUT 2000 26 27#define SUN6I_FIFO_DEPTH 128 28#define SUN8I_FIFO_DEPTH 64 29 30#define SUN6I_GBL_CTL_REG 0x04 31#define SUN6I_GBL_CTL_BUS_ENABLE BIT(0) 32#define SUN6I_GBL_CTL_MASTER BIT(1) 33#define SUN6I_GBL_CTL_TP BIT(7) 34#define SUN6I_GBL_CTL_RST BIT(31) 35 36#define SUN6I_TFR_CTL_REG 0x08 37#define SUN6I_TFR_CTL_CPHA BIT(0) 38#define SUN6I_TFR_CTL_CPOL BIT(1) 39#define SUN6I_TFR_CTL_SPOL BIT(2) 40#define SUN6I_TFR_CTL_CS_MASK 0x30 41#define SUN6I_TFR_CTL_CS(cs) (((cs) << 4) & SUN6I_TFR_CTL_CS_MASK) 42#define SUN6I_TFR_CTL_CS_MANUAL BIT(6) 43#define SUN6I_TFR_CTL_CS_LEVEL BIT(7) 44#define SUN6I_TFR_CTL_DHB BIT(8) 45#define SUN6I_TFR_CTL_SDC BIT(11) 46#define SUN6I_TFR_CTL_FBS BIT(12) 47#define SUN6I_TFR_CTL_SDM BIT(13) 48#define SUN6I_TFR_CTL_XCH BIT(31) 49 50#define SUN6I_INT_CTL_REG 0x10 51#define SUN6I_INT_CTL_RF_RDY BIT(0) 52#define SUN6I_INT_CTL_TF_ERQ BIT(4) 53#define SUN6I_INT_CTL_RF_OVF BIT(8) 54#define SUN6I_INT_CTL_TC BIT(12) 55 56#define SUN6I_INT_STA_REG 0x14 57 58#define SUN6I_FIFO_CTL_REG 0x18 59#define SUN6I_FIFO_CTL_RF_RDY_TRIG_LEVEL_MASK 0xff 60#define SUN6I_FIFO_CTL_RF_DRQ_EN BIT(8) 61#define SUN6I_FIFO_CTL_RF_RDY_TRIG_LEVEL_BITS 0 62#define SUN6I_FIFO_CTL_RF_RST BIT(15) 63#define SUN6I_FIFO_CTL_TF_ERQ_TRIG_LEVEL_MASK 0xff 64#define SUN6I_FIFO_CTL_TF_ERQ_TRIG_LEVEL_BITS 16 65#define SUN6I_FIFO_CTL_TF_DRQ_EN BIT(24) 66#define SUN6I_FIFO_CTL_TF_RST BIT(31) 67 68#define SUN6I_FIFO_STA_REG 0x1c 69#define SUN6I_FIFO_STA_RF_CNT_MASK GENMASK(7, 0) 70#define SUN6I_FIFO_STA_TF_CNT_MASK GENMASK(23, 16) 71 72#define SUN6I_CLK_CTL_REG 0x24 73#define SUN6I_CLK_CTL_CDR2_MASK 0xff 74#define SUN6I_CLK_CTL_CDR2(div) (((div) & SUN6I_CLK_CTL_CDR2_MASK) << 0) 75#define SUN6I_CLK_CTL_CDR1_MASK 0xf 76#define SUN6I_CLK_CTL_CDR1(div) (((div) & SUN6I_CLK_CTL_CDR1_MASK) << 8) 77#define SUN6I_CLK_CTL_DRS BIT(12) 78 79#define SUN6I_MAX_XFER_SIZE 0xffffff 80 81#define SUN6I_BURST_CNT_REG 0x30 82 83#define SUN6I_XMIT_CNT_REG 0x34 84 85#define SUN6I_BURST_CTL_CNT_REG 0x38 86#define SUN6I_BURST_CTL_CNT_STC_MASK GENMASK(23, 0) 87#define SUN6I_BURST_CTL_CNT_DRM BIT(28) 88#define SUN6I_BURST_CTL_CNT_QUAD_EN BIT(29) 89 90#define SUN6I_TXDATA_REG 0x200 91#define SUN6I_RXDATA_REG 0x300 92 93struct sun6i_spi_cfg { 94 unsigned long fifo_depth; 95 bool has_clk_ctl; 96 u32 mode_bits; 97}; 98 99struct sun6i_spi { 100 struct spi_controller *host; 101 void __iomem *base_addr; 102 dma_addr_t dma_addr_rx; 103 dma_addr_t dma_addr_tx; 104 struct clk *hclk; 105 struct clk *mclk; 106 struct reset_control *rstc; 107 108 struct completion done; 109 struct completion dma_rx_done; 110 111 const u8 *tx_buf; 112 u8 *rx_buf; 113 int len; 114 const struct sun6i_spi_cfg *cfg; 115}; 116 117static inline u32 sun6i_spi_read(struct sun6i_spi *sspi, u32 reg) 118{ 119 return readl(sspi->base_addr + reg); 120} 121 122static inline void sun6i_spi_write(struct sun6i_spi *sspi, u32 reg, u32 value) 123{ 124 writel(value, sspi->base_addr + reg); 125} 126 127static inline u32 sun6i_spi_get_rx_fifo_count(struct sun6i_spi *sspi) 128{ 129 u32 reg = sun6i_spi_read(sspi, SUN6I_FIFO_STA_REG); 130 131 return FIELD_GET(SUN6I_FIFO_STA_RF_CNT_MASK, reg); 132} 133 134static inline u32 sun6i_spi_get_tx_fifo_count(struct sun6i_spi *sspi) 135{ 136 u32 reg = sun6i_spi_read(sspi, SUN6I_FIFO_STA_REG); 137 138 return FIELD_GET(SUN6I_FIFO_STA_TF_CNT_MASK, reg); 139} 140 141static inline void sun6i_spi_disable_interrupt(struct sun6i_spi *sspi, u32 mask) 142{ 143 u32 reg = sun6i_spi_read(sspi, SUN6I_INT_CTL_REG); 144 145 reg &= ~mask; 146 sun6i_spi_write(sspi, SUN6I_INT_CTL_REG, reg); 147} 148 149static inline void sun6i_spi_drain_fifo(struct sun6i_spi *sspi) 150{ 151 u32 len; 152 u8 byte; 153 154 /* See how much data is available */ 155 len = sun6i_spi_get_rx_fifo_count(sspi); 156 157 while (len--) { 158 byte = readb(sspi->base_addr + SUN6I_RXDATA_REG); 159 if (sspi->rx_buf) 160 *sspi->rx_buf++ = byte; 161 } 162} 163 164static inline void sun6i_spi_fill_fifo(struct sun6i_spi *sspi) 165{ 166 u32 cnt; 167 int len; 168 u8 byte; 169 170 /* See how much data we can fit */ 171 cnt = sspi->cfg->fifo_depth - sun6i_spi_get_tx_fifo_count(sspi); 172 173 len = min((int)cnt, sspi->len); 174 175 while (len--) { 176 byte = sspi->tx_buf ? *sspi->tx_buf++ : 0; 177 writeb(byte, sspi->base_addr + SUN6I_TXDATA_REG); 178 sspi->len--; 179 } 180} 181 182static void sun6i_spi_set_cs(struct spi_device *spi, bool enable) 183{ 184 struct sun6i_spi *sspi = spi_controller_get_devdata(spi->controller); 185 u32 reg; 186 187 reg = sun6i_spi_read(sspi, SUN6I_TFR_CTL_REG); 188 reg &= ~SUN6I_TFR_CTL_CS_MASK; 189 reg |= SUN6I_TFR_CTL_CS(spi_get_chipselect(spi, 0)); 190 191 if (enable) 192 reg |= SUN6I_TFR_CTL_CS_LEVEL; 193 else 194 reg &= ~SUN6I_TFR_CTL_CS_LEVEL; 195 196 sun6i_spi_write(sspi, SUN6I_TFR_CTL_REG, reg); 197} 198 199static size_t sun6i_spi_max_transfer_size(struct spi_device *spi) 200{ 201 return SUN6I_MAX_XFER_SIZE - 1; 202} 203 204static void sun6i_spi_dma_rx_cb(void *param) 205{ 206 struct sun6i_spi *sspi = param; 207 208 complete(&sspi->dma_rx_done); 209} 210 211static int sun6i_spi_prepare_dma(struct sun6i_spi *sspi, 212 struct spi_transfer *tfr) 213{ 214 struct dma_async_tx_descriptor *rxdesc, *txdesc; 215 struct spi_controller *host = sspi->host; 216 217 rxdesc = NULL; 218 if (tfr->rx_buf) { 219 struct dma_slave_config rxconf = { 220 .direction = DMA_DEV_TO_MEM, 221 .src_addr = sspi->dma_addr_rx, 222 .src_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE, 223 .src_maxburst = 8, 224 }; 225 226 dmaengine_slave_config(host->dma_rx, &rxconf); 227 228 rxdesc = dmaengine_prep_slave_sg(host->dma_rx, 229 tfr->rx_sg.sgl, 230 tfr->rx_sg.nents, 231 DMA_DEV_TO_MEM, 232 DMA_PREP_INTERRUPT); 233 if (!rxdesc) 234 return -EINVAL; 235 rxdesc->callback_param = sspi; 236 rxdesc->callback = sun6i_spi_dma_rx_cb; 237 } 238 239 txdesc = NULL; 240 if (tfr->tx_buf) { 241 struct dma_slave_config txconf = { 242 .direction = DMA_MEM_TO_DEV, 243 .dst_addr = sspi->dma_addr_tx, 244 .dst_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES, 245 .dst_maxburst = 8, 246 }; 247 248 dmaengine_slave_config(host->dma_tx, &txconf); 249 250 txdesc = dmaengine_prep_slave_sg(host->dma_tx, 251 tfr->tx_sg.sgl, 252 tfr->tx_sg.nents, 253 DMA_MEM_TO_DEV, 254 DMA_PREP_INTERRUPT); 255 if (!txdesc) { 256 if (rxdesc) 257 dmaengine_terminate_sync(host->dma_rx); 258 return -EINVAL; 259 } 260 } 261 262 if (tfr->rx_buf) { 263 dmaengine_submit(rxdesc); 264 dma_async_issue_pending(host->dma_rx); 265 } 266 267 if (tfr->tx_buf) { 268 dmaengine_submit(txdesc); 269 dma_async_issue_pending(host->dma_tx); 270 } 271 272 return 0; 273} 274 275static int sun6i_spi_transfer_one(struct spi_controller *host, 276 struct spi_device *spi, 277 struct spi_transfer *tfr) 278{ 279 struct sun6i_spi *sspi = spi_controller_get_devdata(host); 280 unsigned int div, div_cdr1, div_cdr2, timeout; 281 unsigned int start, end, tx_time; 282 unsigned int trig_level; 283 unsigned int tx_len = 0, rx_len = 0, nbits = 0; 284 bool use_dma; 285 int ret = 0; 286 u32 reg; 287 288 if (tfr->len > SUN6I_MAX_XFER_SIZE) 289 return -EINVAL; 290 291 reinit_completion(&sspi->done); 292 reinit_completion(&sspi->dma_rx_done); 293 sspi->tx_buf = tfr->tx_buf; 294 sspi->rx_buf = tfr->rx_buf; 295 sspi->len = tfr->len; 296 use_dma = host->can_dma ? host->can_dma(host, spi, tfr) : false; 297 298 /* Clear pending interrupts */ 299 sun6i_spi_write(sspi, SUN6I_INT_STA_REG, ~0); 300 301 /* Reset FIFO */ 302 sun6i_spi_write(sspi, SUN6I_FIFO_CTL_REG, 303 SUN6I_FIFO_CTL_RF_RST | SUN6I_FIFO_CTL_TF_RST); 304 305 reg = 0; 306 307 if (!use_dma) { 308 /* 309 * Setup FIFO interrupt trigger level 310 * Here we choose 3/4 of the full fifo depth, as it's 311 * the hardcoded value used in old generation of Allwinner 312 * SPI controller. (See spi-sun4i.c) 313 */ 314 trig_level = sspi->cfg->fifo_depth / 4 * 3; 315 } else { 316 /* 317 * Setup FIFO DMA request trigger level 318 * We choose 1/2 of the full fifo depth, that value will 319 * be used as DMA burst length. 320 */ 321 trig_level = sspi->cfg->fifo_depth / 2; 322 323 if (tfr->tx_buf) 324 reg |= SUN6I_FIFO_CTL_TF_DRQ_EN; 325 if (tfr->rx_buf) 326 reg |= SUN6I_FIFO_CTL_RF_DRQ_EN; 327 } 328 329 reg |= (trig_level << SUN6I_FIFO_CTL_RF_RDY_TRIG_LEVEL_BITS) | 330 (trig_level << SUN6I_FIFO_CTL_TF_ERQ_TRIG_LEVEL_BITS); 331 332 sun6i_spi_write(sspi, SUN6I_FIFO_CTL_REG, reg); 333 334 /* 335 * Setup the transfer control register: Chip Select, 336 * polarities, etc. 337 */ 338 reg = sun6i_spi_read(sspi, SUN6I_TFR_CTL_REG); 339 340 if (spi->mode & SPI_CPOL) 341 reg |= SUN6I_TFR_CTL_CPOL; 342 else 343 reg &= ~SUN6I_TFR_CTL_CPOL; 344 345 if (spi->mode & SPI_CPHA) 346 reg |= SUN6I_TFR_CTL_CPHA; 347 else 348 reg &= ~SUN6I_TFR_CTL_CPHA; 349 350 if (spi->mode & SPI_LSB_FIRST) 351 reg |= SUN6I_TFR_CTL_FBS; 352 else 353 reg &= ~SUN6I_TFR_CTL_FBS; 354 355 /* 356 * If it's a TX only transfer, we don't want to fill the RX 357 * FIFO with bogus data 358 */ 359 if (sspi->rx_buf) { 360 reg &= ~SUN6I_TFR_CTL_DHB; 361 rx_len = tfr->len; 362 } else { 363 reg |= SUN6I_TFR_CTL_DHB; 364 } 365 366 /* We want to control the chip select manually */ 367 reg |= SUN6I_TFR_CTL_CS_MANUAL; 368 369 sun6i_spi_write(sspi, SUN6I_TFR_CTL_REG, reg); 370 371 if (sspi->cfg->has_clk_ctl) { 372 unsigned int mclk_rate = clk_get_rate(sspi->mclk); 373 374 /* Ensure that we have a parent clock fast enough */ 375 if (mclk_rate < (2 * tfr->speed_hz)) { 376 clk_set_rate(sspi->mclk, 2 * tfr->speed_hz); 377 mclk_rate = clk_get_rate(sspi->mclk); 378 } 379 380 /* 381 * Setup clock divider. 382 * 383 * We have two choices there. Either we can use the clock 384 * divide rate 1, which is calculated thanks to this formula: 385 * SPI_CLK = MOD_CLK / (2 ^ cdr) 386 * Or we can use CDR2, which is calculated with the formula: 387 * SPI_CLK = MOD_CLK / (2 * (cdr + 1)) 388 * Wether we use the former or the latter is set through the 389 * DRS bit. 390 * 391 * First try CDR2, and if we can't reach the expected 392 * frequency, fall back to CDR1. 393 */ 394 div_cdr1 = DIV_ROUND_UP(mclk_rate, tfr->speed_hz); 395 div_cdr2 = DIV_ROUND_UP(div_cdr1, 2); 396 if (div_cdr2 <= (SUN6I_CLK_CTL_CDR2_MASK + 1)) { 397 reg = SUN6I_CLK_CTL_CDR2(div_cdr2 - 1) | SUN6I_CLK_CTL_DRS; 398 tfr->effective_speed_hz = mclk_rate / (2 * div_cdr2); 399 } else { 400 div = min(SUN6I_CLK_CTL_CDR1_MASK, order_base_2(div_cdr1)); 401 reg = SUN6I_CLK_CTL_CDR1(div); 402 tfr->effective_speed_hz = mclk_rate / (1 << div); 403 } 404 405 sun6i_spi_write(sspi, SUN6I_CLK_CTL_REG, reg); 406 } else { 407 clk_set_rate(sspi->mclk, tfr->speed_hz); 408 tfr->effective_speed_hz = clk_get_rate(sspi->mclk); 409 410 /* 411 * Configure work mode. 412 * 413 * There are three work modes depending on the controller clock 414 * frequency: 415 * - normal sample mode : CLK <= 24MHz SDM=1 SDC=0 416 * - delay half-cycle sample mode : CLK <= 40MHz SDM=0 SDC=0 417 * - delay one-cycle sample mode : CLK >= 80MHz SDM=0 SDC=1 418 */ 419 reg = sun6i_spi_read(sspi, SUN6I_TFR_CTL_REG); 420 reg &= ~(SUN6I_TFR_CTL_SDM | SUN6I_TFR_CTL_SDC); 421 422 if (tfr->effective_speed_hz <= 24000000) 423 reg |= SUN6I_TFR_CTL_SDM; 424 else if (tfr->effective_speed_hz >= 80000000) 425 reg |= SUN6I_TFR_CTL_SDC; 426 427 sun6i_spi_write(sspi, SUN6I_TFR_CTL_REG, reg); 428 } 429 430 /* Finally enable the bus - doing so before might raise SCK to HIGH */ 431 reg = sun6i_spi_read(sspi, SUN6I_GBL_CTL_REG); 432 reg |= SUN6I_GBL_CTL_BUS_ENABLE; 433 sun6i_spi_write(sspi, SUN6I_GBL_CTL_REG, reg); 434 435 /* Setup the transfer now... */ 436 if (sspi->tx_buf) { 437 tx_len = tfr->len; 438 nbits = tfr->tx_nbits; 439 } else if (tfr->rx_buf) { 440 nbits = tfr->rx_nbits; 441 } 442 443 switch (nbits) { 444 case SPI_NBITS_DUAL: 445 reg = SUN6I_BURST_CTL_CNT_DRM; 446 break; 447 case SPI_NBITS_QUAD: 448 reg = SUN6I_BURST_CTL_CNT_QUAD_EN; 449 break; 450 case SPI_NBITS_SINGLE: 451 default: 452 reg = FIELD_PREP(SUN6I_BURST_CTL_CNT_STC_MASK, tx_len); 453 } 454 455 /* Setup the counters */ 456 sun6i_spi_write(sspi, SUN6I_BURST_CTL_CNT_REG, reg); 457 sun6i_spi_write(sspi, SUN6I_BURST_CNT_REG, tfr->len); 458 sun6i_spi_write(sspi, SUN6I_XMIT_CNT_REG, tx_len); 459 460 if (!use_dma) { 461 /* Fill the TX FIFO */ 462 sun6i_spi_fill_fifo(sspi); 463 } else { 464 ret = sun6i_spi_prepare_dma(sspi, tfr); 465 if (ret) { 466 dev_warn(&host->dev, 467 "%s: prepare DMA failed, ret=%d", 468 dev_name(&spi->dev), ret); 469 return ret; 470 } 471 } 472 473 /* Enable the interrupts */ 474 reg = SUN6I_INT_CTL_TC; 475 476 if (!use_dma) { 477 if (rx_len > sspi->cfg->fifo_depth) 478 reg |= SUN6I_INT_CTL_RF_RDY; 479 if (tx_len > sspi->cfg->fifo_depth) 480 reg |= SUN6I_INT_CTL_TF_ERQ; 481 } 482 483 sun6i_spi_write(sspi, SUN6I_INT_CTL_REG, reg); 484 485 /* Start the transfer */ 486 reg = sun6i_spi_read(sspi, SUN6I_TFR_CTL_REG); 487 sun6i_spi_write(sspi, SUN6I_TFR_CTL_REG, reg | SUN6I_TFR_CTL_XCH); 488 489 tx_time = spi_controller_xfer_timeout(host, tfr); 490 start = jiffies; 491 timeout = wait_for_completion_timeout(&sspi->done, 492 msecs_to_jiffies(tx_time)); 493 494 if (!use_dma) { 495 sun6i_spi_drain_fifo(sspi); 496 } else { 497 if (timeout && rx_len) { 498 /* 499 * Even though RX on the peripheral side has finished 500 * RX DMA might still be in flight 501 */ 502 timeout = wait_for_completion_timeout(&sspi->dma_rx_done, 503 timeout); 504 if (!timeout) 505 dev_warn(&host->dev, "RX DMA timeout\n"); 506 } 507 } 508 509 end = jiffies; 510 if (!timeout) { 511 dev_warn(&host->dev, 512 "%s: timeout transferring %u bytes@%iHz for %i(%i)ms", 513 dev_name(&spi->dev), tfr->len, tfr->speed_hz, 514 jiffies_to_msecs(end - start), tx_time); 515 ret = -ETIMEDOUT; 516 } 517 518 sun6i_spi_write(sspi, SUN6I_INT_CTL_REG, 0); 519 520 if (ret && use_dma) { 521 dmaengine_terminate_sync(host->dma_rx); 522 dmaengine_terminate_sync(host->dma_tx); 523 } 524 525 return ret; 526} 527 528static irqreturn_t sun6i_spi_handler(int irq, void *dev_id) 529{ 530 struct sun6i_spi *sspi = dev_id; 531 u32 status = sun6i_spi_read(sspi, SUN6I_INT_STA_REG); 532 533 /* Transfer complete */ 534 if (status & SUN6I_INT_CTL_TC) { 535 sun6i_spi_write(sspi, SUN6I_INT_STA_REG, SUN6I_INT_CTL_TC); 536 complete(&sspi->done); 537 return IRQ_HANDLED; 538 } 539 540 /* Receive FIFO 3/4 full */ 541 if (status & SUN6I_INT_CTL_RF_RDY) { 542 sun6i_spi_drain_fifo(sspi); 543 /* Only clear the interrupt _after_ draining the FIFO */ 544 sun6i_spi_write(sspi, SUN6I_INT_STA_REG, SUN6I_INT_CTL_RF_RDY); 545 return IRQ_HANDLED; 546 } 547 548 /* Transmit FIFO 3/4 empty */ 549 if (status & SUN6I_INT_CTL_TF_ERQ) { 550 sun6i_spi_fill_fifo(sspi); 551 552 if (!sspi->len) 553 /* nothing left to transmit */ 554 sun6i_spi_disable_interrupt(sspi, SUN6I_INT_CTL_TF_ERQ); 555 556 /* Only clear the interrupt _after_ re-seeding the FIFO */ 557 sun6i_spi_write(sspi, SUN6I_INT_STA_REG, SUN6I_INT_CTL_TF_ERQ); 558 559 return IRQ_HANDLED; 560 } 561 562 return IRQ_NONE; 563} 564 565static int sun6i_spi_runtime_resume(struct device *dev) 566{ 567 struct spi_controller *host = dev_get_drvdata(dev); 568 struct sun6i_spi *sspi = spi_controller_get_devdata(host); 569 int ret; 570 571 ret = clk_prepare_enable(sspi->hclk); 572 if (ret) { 573 dev_err(dev, "Couldn't enable AHB clock\n"); 574 goto out; 575 } 576 577 ret = clk_prepare_enable(sspi->mclk); 578 if (ret) { 579 dev_err(dev, "Couldn't enable module clock\n"); 580 goto err; 581 } 582 583 ret = reset_control_deassert(sspi->rstc); 584 if (ret) { 585 dev_err(dev, "Couldn't deassert the device from reset\n"); 586 goto err2; 587 } 588 589 sun6i_spi_write(sspi, SUN6I_GBL_CTL_REG, 590 SUN6I_GBL_CTL_MASTER | SUN6I_GBL_CTL_TP); 591 592 return 0; 593 594err2: 595 clk_disable_unprepare(sspi->mclk); 596err: 597 clk_disable_unprepare(sspi->hclk); 598out: 599 return ret; 600} 601 602static int sun6i_spi_runtime_suspend(struct device *dev) 603{ 604 struct spi_controller *host = dev_get_drvdata(dev); 605 struct sun6i_spi *sspi = spi_controller_get_devdata(host); 606 607 reset_control_assert(sspi->rstc); 608 clk_disable_unprepare(sspi->mclk); 609 clk_disable_unprepare(sspi->hclk); 610 611 return 0; 612} 613 614static bool sun6i_spi_can_dma(struct spi_controller *host, 615 struct spi_device *spi, 616 struct spi_transfer *xfer) 617{ 618 struct sun6i_spi *sspi = spi_controller_get_devdata(host); 619 620 /* 621 * If the number of spi words to transfer is less or equal than 622 * the fifo length we can just fill the fifo and wait for a single 623 * irq, so don't bother setting up dma 624 */ 625 return xfer->len > sspi->cfg->fifo_depth; 626} 627 628static int sun6i_spi_probe(struct platform_device *pdev) 629{ 630 struct spi_controller *host; 631 struct sun6i_spi *sspi; 632 struct resource *mem; 633 int ret = 0, irq; 634 635 host = spi_alloc_host(&pdev->dev, sizeof(struct sun6i_spi)); 636 if (!host) { 637 dev_err(&pdev->dev, "Unable to allocate SPI Host\n"); 638 return -ENOMEM; 639 } 640 641 platform_set_drvdata(pdev, host); 642 sspi = spi_controller_get_devdata(host); 643 644 sspi->base_addr = devm_platform_get_and_ioremap_resource(pdev, 0, &mem); 645 if (IS_ERR(sspi->base_addr)) { 646 ret = PTR_ERR(sspi->base_addr); 647 goto err_free_host; 648 } 649 650 irq = platform_get_irq(pdev, 0); 651 if (irq < 0) { 652 ret = -ENXIO; 653 goto err_free_host; 654 } 655 656 ret = devm_request_irq(&pdev->dev, irq, sun6i_spi_handler, 657 0, "sun6i-spi", sspi); 658 if (ret) { 659 dev_err(&pdev->dev, "Cannot request IRQ\n"); 660 goto err_free_host; 661 } 662 663 sspi->host = host; 664 sspi->cfg = of_device_get_match_data(&pdev->dev); 665 666 host->max_speed_hz = 100 * 1000 * 1000; 667 host->min_speed_hz = 3 * 1000; 668 host->use_gpio_descriptors = true; 669 host->set_cs = sun6i_spi_set_cs; 670 host->transfer_one = sun6i_spi_transfer_one; 671 host->num_chipselect = 4; 672 host->mode_bits = SPI_CPOL | SPI_CPHA | SPI_CS_HIGH | SPI_LSB_FIRST | 673 sspi->cfg->mode_bits; 674 host->bits_per_word_mask = SPI_BPW_MASK(8); 675 host->dev.of_node = pdev->dev.of_node; 676 host->auto_runtime_pm = true; 677 host->max_transfer_size = sun6i_spi_max_transfer_size; 678 679 sspi->hclk = devm_clk_get(&pdev->dev, "ahb"); 680 if (IS_ERR(sspi->hclk)) { 681 dev_err(&pdev->dev, "Unable to acquire AHB clock\n"); 682 ret = PTR_ERR(sspi->hclk); 683 goto err_free_host; 684 } 685 686 sspi->mclk = devm_clk_get(&pdev->dev, "mod"); 687 if (IS_ERR(sspi->mclk)) { 688 dev_err(&pdev->dev, "Unable to acquire module clock\n"); 689 ret = PTR_ERR(sspi->mclk); 690 goto err_free_host; 691 } 692 693 init_completion(&sspi->done); 694 init_completion(&sspi->dma_rx_done); 695 696 sspi->rstc = devm_reset_control_get_exclusive(&pdev->dev, NULL); 697 if (IS_ERR(sspi->rstc)) { 698 dev_err(&pdev->dev, "Couldn't get reset controller\n"); 699 ret = PTR_ERR(sspi->rstc); 700 goto err_free_host; 701 } 702 703 host->dma_tx = dma_request_chan(&pdev->dev, "tx"); 704 if (IS_ERR(host->dma_tx)) { 705 /* Check tx to see if we need defer probing driver */ 706 if (PTR_ERR(host->dma_tx) == -EPROBE_DEFER) { 707 ret = -EPROBE_DEFER; 708 goto err_free_host; 709 } 710 dev_warn(&pdev->dev, "Failed to request TX DMA channel\n"); 711 host->dma_tx = NULL; 712 } 713 714 host->dma_rx = dma_request_chan(&pdev->dev, "rx"); 715 if (IS_ERR(host->dma_rx)) { 716 if (PTR_ERR(host->dma_rx) == -EPROBE_DEFER) { 717 ret = -EPROBE_DEFER; 718 goto err_free_dma_tx; 719 } 720 dev_warn(&pdev->dev, "Failed to request RX DMA channel\n"); 721 host->dma_rx = NULL; 722 } 723 724 if (host->dma_tx && host->dma_rx) { 725 sspi->dma_addr_tx = mem->start + SUN6I_TXDATA_REG; 726 sspi->dma_addr_rx = mem->start + SUN6I_RXDATA_REG; 727 host->can_dma = sun6i_spi_can_dma; 728 } 729 730 /* 731 * This wake-up/shutdown pattern is to be able to have the 732 * device woken up, even if runtime_pm is disabled 733 */ 734 ret = sun6i_spi_runtime_resume(&pdev->dev); 735 if (ret) { 736 dev_err(&pdev->dev, "Couldn't resume the device\n"); 737 goto err_free_dma_rx; 738 } 739 740 pm_runtime_set_autosuspend_delay(&pdev->dev, SUN6I_AUTOSUSPEND_TIMEOUT); 741 pm_runtime_use_autosuspend(&pdev->dev); 742 pm_runtime_set_active(&pdev->dev); 743 pm_runtime_enable(&pdev->dev); 744 745 ret = devm_spi_register_controller(&pdev->dev, host); 746 if (ret) { 747 dev_err(&pdev->dev, "cannot register SPI host\n"); 748 goto err_pm_disable; 749 } 750 751 return 0; 752 753err_pm_disable: 754 pm_runtime_disable(&pdev->dev); 755 sun6i_spi_runtime_suspend(&pdev->dev); 756err_free_dma_rx: 757 if (host->dma_rx) 758 dma_release_channel(host->dma_rx); 759err_free_dma_tx: 760 if (host->dma_tx) 761 dma_release_channel(host->dma_tx); 762err_free_host: 763 spi_controller_put(host); 764 return ret; 765} 766 767static void sun6i_spi_remove(struct platform_device *pdev) 768{ 769 struct spi_controller *host = platform_get_drvdata(pdev); 770 771 pm_runtime_force_suspend(&pdev->dev); 772 773 if (host->dma_tx) 774 dma_release_channel(host->dma_tx); 775 if (host->dma_rx) 776 dma_release_channel(host->dma_rx); 777} 778 779static const struct sun6i_spi_cfg sun6i_a31_spi_cfg = { 780 .fifo_depth = SUN6I_FIFO_DEPTH, 781 .has_clk_ctl = true, 782}; 783 784static const struct sun6i_spi_cfg sun8i_h3_spi_cfg = { 785 .fifo_depth = SUN8I_FIFO_DEPTH, 786 .has_clk_ctl = true, 787}; 788 789static const struct sun6i_spi_cfg sun50i_r329_spi_cfg = { 790 .fifo_depth = SUN8I_FIFO_DEPTH, 791 .mode_bits = SPI_RX_DUAL | SPI_TX_DUAL | SPI_RX_QUAD | SPI_TX_QUAD, 792}; 793 794static const struct of_device_id sun6i_spi_match[] = { 795 { .compatible = "allwinner,sun6i-a31-spi", .data = &sun6i_a31_spi_cfg }, 796 { .compatible = "allwinner,sun8i-h3-spi", .data = &sun8i_h3_spi_cfg }, 797 { 798 .compatible = "allwinner,sun50i-r329-spi", 799 .data = &sun50i_r329_spi_cfg 800 }, 801 {} 802}; 803MODULE_DEVICE_TABLE(of, sun6i_spi_match); 804 805static const struct dev_pm_ops sun6i_spi_pm_ops = { 806 .runtime_resume = sun6i_spi_runtime_resume, 807 .runtime_suspend = sun6i_spi_runtime_suspend, 808}; 809 810static struct platform_driver sun6i_spi_driver = { 811 .probe = sun6i_spi_probe, 812 .remove_new = sun6i_spi_remove, 813 .driver = { 814 .name = "sun6i-spi", 815 .of_match_table = sun6i_spi_match, 816 .pm = &sun6i_spi_pm_ops, 817 }, 818}; 819module_platform_driver(sun6i_spi_driver); 820 821MODULE_AUTHOR("Pan Nan <pannan@allwinnertech.com>"); 822MODULE_AUTHOR("Maxime Ripard <maxime.ripard@free-electrons.com>"); 823MODULE_DESCRIPTION("Allwinner A31 SPI controller driver"); 824MODULE_LICENSE("GPL"); 825