1// SPDX-License-Identifier: GPL-2.0-only 2/* 3 * Copyright (C) ST-Ericsson SA 2012 4 * Copyright (c) 2012 Sony Mobile Communications AB 5 * 6 * Charging algorithm driver for AB8500 7 * 8 * Authors: 9 * Johan Palsson <johan.palsson@stericsson.com> 10 * Karl Komierowski <karl.komierowski@stericsson.com> 11 * Arun R Murthy <arun.murthy@stericsson.com> 12 * Author: Imre Sunyi <imre.sunyi@sonymobile.com> 13 */ 14 15#include <linux/init.h> 16#include <linux/module.h> 17#include <linux/device.h> 18#include <linux/component.h> 19#include <linux/hrtimer.h> 20#include <linux/interrupt.h> 21#include <linux/delay.h> 22#include <linux/slab.h> 23#include <linux/platform_device.h> 24#include <linux/power_supply.h> 25#include <linux/completion.h> 26#include <linux/workqueue.h> 27#include <linux/kobject.h> 28#include <linux/of.h> 29#include <linux/mfd/core.h> 30#include <linux/mfd/abx500.h> 31#include <linux/mfd/abx500/ab8500.h> 32#include <linux/notifier.h> 33 34#include "ab8500-bm.h" 35#include "ab8500-chargalg.h" 36 37/* Watchdog kick interval */ 38#define CHG_WD_INTERVAL (6 * HZ) 39 40/* End-of-charge criteria counter */ 41#define EOC_COND_CNT 10 42 43/* One hour expressed in seconds */ 44#define ONE_HOUR_IN_SECONDS 3600 45 46/* Five minutes expressed in seconds */ 47#define FIVE_MINUTES_IN_SECONDS 300 48 49/* 50 * This is the battery capacity limit that will trigger a new 51 * full charging cycle in the case where maintenance charging 52 * has been disabled 53 */ 54#define AB8500_RECHARGE_CAP 95 55 56enum ab8500_chargers { 57 NO_CHG, 58 AC_CHG, 59 USB_CHG, 60}; 61 62struct ab8500_chargalg_charger_info { 63 enum ab8500_chargers conn_chg; 64 enum ab8500_chargers prev_conn_chg; 65 enum ab8500_chargers online_chg; 66 enum ab8500_chargers prev_online_chg; 67 enum ab8500_chargers charger_type; 68 bool usb_chg_ok; 69 bool ac_chg_ok; 70 int usb_volt_uv; 71 int usb_curr_ua; 72 int ac_volt_uv; 73 int ac_curr_ua; 74 int usb_vset_uv; 75 int usb_iset_ua; 76 int ac_vset_uv; 77 int ac_iset_ua; 78}; 79 80struct ab8500_chargalg_battery_data { 81 int temp; 82 int volt_uv; 83 int avg_curr_ua; 84 int inst_curr_ua; 85 int percent; 86}; 87 88enum ab8500_chargalg_states { 89 STATE_HANDHELD_INIT, 90 STATE_HANDHELD, 91 STATE_CHG_NOT_OK_INIT, 92 STATE_CHG_NOT_OK, 93 STATE_HW_TEMP_PROTECT_INIT, 94 STATE_HW_TEMP_PROTECT, 95 STATE_NORMAL_INIT, 96 STATE_NORMAL, 97 STATE_WAIT_FOR_RECHARGE_INIT, 98 STATE_WAIT_FOR_RECHARGE, 99 STATE_MAINTENANCE_A_INIT, 100 STATE_MAINTENANCE_A, 101 STATE_MAINTENANCE_B_INIT, 102 STATE_MAINTENANCE_B, 103 STATE_TEMP_UNDEROVER_INIT, 104 STATE_TEMP_UNDEROVER, 105 STATE_TEMP_LOWHIGH_INIT, 106 STATE_TEMP_LOWHIGH, 107 STATE_OVV_PROTECT_INIT, 108 STATE_OVV_PROTECT, 109 STATE_SAFETY_TIMER_EXPIRED_INIT, 110 STATE_SAFETY_TIMER_EXPIRED, 111 STATE_BATT_REMOVED_INIT, 112 STATE_BATT_REMOVED, 113 STATE_WD_EXPIRED_INIT, 114 STATE_WD_EXPIRED, 115}; 116 117static const char * const states[] = { 118 "HANDHELD_INIT", 119 "HANDHELD", 120 "CHG_NOT_OK_INIT", 121 "CHG_NOT_OK", 122 "HW_TEMP_PROTECT_INIT", 123 "HW_TEMP_PROTECT", 124 "NORMAL_INIT", 125 "NORMAL", 126 "WAIT_FOR_RECHARGE_INIT", 127 "WAIT_FOR_RECHARGE", 128 "MAINTENANCE_A_INIT", 129 "MAINTENANCE_A", 130 "MAINTENANCE_B_INIT", 131 "MAINTENANCE_B", 132 "TEMP_UNDEROVER_INIT", 133 "TEMP_UNDEROVER", 134 "TEMP_LOWHIGH_INIT", 135 "TEMP_LOWHIGH", 136 "OVV_PROTECT_INIT", 137 "OVV_PROTECT", 138 "SAFETY_TIMER_EXPIRED_INIT", 139 "SAFETY_TIMER_EXPIRED", 140 "BATT_REMOVED_INIT", 141 "BATT_REMOVED", 142 "WD_EXPIRED_INIT", 143 "WD_EXPIRED", 144}; 145 146struct ab8500_chargalg_events { 147 bool batt_unknown; 148 bool mainextchnotok; 149 bool batt_ovv; 150 bool batt_rem; 151 bool btemp_underover; 152 bool btemp_low; 153 bool btemp_high; 154 bool main_thermal_prot; 155 bool usb_thermal_prot; 156 bool main_ovv; 157 bool vbus_ovv; 158 bool usbchargernotok; 159 bool safety_timer_expired; 160 bool maintenance_timer_expired; 161 bool ac_wd_expired; 162 bool usb_wd_expired; 163 bool ac_cv_active; 164 bool usb_cv_active; 165 bool vbus_collapsed; 166}; 167 168/** 169 * struct ab8500_charge_curr_maximization - Charger maximization parameters 170 * @original_iset_ua: the non optimized/maximised charger current 171 * @current_iset_ua: the charging current used at this moment 172 * @condition_cnt: number of iterations needed before a new charger current 173 is set 174 * @max_current_ua: maximum charger current 175 * @wait_cnt: to avoid too fast current step down in case of charger 176 * voltage collapse, we insert this delay between step 177 * down 178 * @level: tells in how many steps the charging current has been 179 increased 180 */ 181struct ab8500_charge_curr_maximization { 182 int original_iset_ua; 183 int current_iset_ua; 184 int condition_cnt; 185 int max_current_ua; 186 int wait_cnt; 187 u8 level; 188}; 189 190enum maxim_ret { 191 MAXIM_RET_NOACTION, 192 MAXIM_RET_CHANGE, 193 MAXIM_RET_IBAT_TOO_HIGH, 194}; 195 196/** 197 * struct ab8500_chargalg - ab8500 Charging algorithm device information 198 * @dev: pointer to the structure device 199 * @charge_status: battery operating status 200 * @eoc_cnt: counter used to determine end-of_charge 201 * @maintenance_chg: indicate if maintenance charge is active 202 * @t_hyst_norm temperature hysteresis when the temperature has been 203 * over or under normal limits 204 * @t_hyst_lowhigh temperature hysteresis when the temperature has been 205 * over or under the high or low limits 206 * @charge_state: current state of the charging algorithm 207 * @ccm charging current maximization parameters 208 * @chg_info: information about connected charger types 209 * @batt_data: data of the battery 210 * @bm: Platform specific battery management information 211 * @parent: pointer to the struct ab8500 212 * @chargalg_psy: structure that holds the battery properties exposed by 213 * the charging algorithm 214 * @events: structure for information about events triggered 215 * @chargalg_wq: work queue for running the charging algorithm 216 * @chargalg_periodic_work: work to run the charging algorithm periodically 217 * @chargalg_wd_work: work to kick the charger watchdog periodically 218 * @chargalg_work: work to run the charging algorithm instantly 219 * @safety_timer: charging safety timer 220 * @maintenance_timer: maintenance charging timer 221 * @chargalg_kobject: structure of type kobject 222 */ 223struct ab8500_chargalg { 224 struct device *dev; 225 int charge_status; 226 int eoc_cnt; 227 bool maintenance_chg; 228 int t_hyst_norm; 229 int t_hyst_lowhigh; 230 enum ab8500_chargalg_states charge_state; 231 struct ab8500_charge_curr_maximization ccm; 232 struct ab8500_chargalg_charger_info chg_info; 233 struct ab8500_chargalg_battery_data batt_data; 234 struct ab8500 *parent; 235 struct ab8500_bm_data *bm; 236 struct power_supply *chargalg_psy; 237 struct ux500_charger *ac_chg; 238 struct ux500_charger *usb_chg; 239 struct ab8500_chargalg_events events; 240 struct workqueue_struct *chargalg_wq; 241 struct delayed_work chargalg_periodic_work; 242 struct delayed_work chargalg_wd_work; 243 struct work_struct chargalg_work; 244 struct hrtimer safety_timer; 245 struct hrtimer maintenance_timer; 246 struct kobject chargalg_kobject; 247}; 248 249/* Main battery properties */ 250static enum power_supply_property ab8500_chargalg_props[] = { 251 POWER_SUPPLY_PROP_STATUS, 252 POWER_SUPPLY_PROP_HEALTH, 253}; 254 255/** 256 * ab8500_chargalg_safety_timer_expired() - Expiration of the safety timer 257 * @timer: pointer to the hrtimer structure 258 * 259 * This function gets called when the safety timer for the charger 260 * expires 261 */ 262static enum hrtimer_restart 263ab8500_chargalg_safety_timer_expired(struct hrtimer *timer) 264{ 265 struct ab8500_chargalg *di = container_of(timer, struct ab8500_chargalg, 266 safety_timer); 267 dev_err(di->dev, "Safety timer expired\n"); 268 di->events.safety_timer_expired = true; 269 270 /* Trigger execution of the algorithm instantly */ 271 queue_work(di->chargalg_wq, &di->chargalg_work); 272 273 return HRTIMER_NORESTART; 274} 275 276/** 277 * ab8500_chargalg_maintenance_timer_expired() - Expiration of 278 * the maintenance timer 279 * @timer: pointer to the timer structure 280 * 281 * This function gets called when the maintenance timer 282 * expires 283 */ 284static enum hrtimer_restart 285ab8500_chargalg_maintenance_timer_expired(struct hrtimer *timer) 286{ 287 288 struct ab8500_chargalg *di = container_of(timer, struct ab8500_chargalg, 289 maintenance_timer); 290 291 dev_dbg(di->dev, "Maintenance timer expired\n"); 292 di->events.maintenance_timer_expired = true; 293 294 /* Trigger execution of the algorithm instantly */ 295 queue_work(di->chargalg_wq, &di->chargalg_work); 296 297 return HRTIMER_NORESTART; 298} 299 300/** 301 * ab8500_chargalg_state_to() - Change charge state 302 * @di: pointer to the ab8500_chargalg structure 303 * 304 * This function gets called when a charge state change should occur 305 */ 306static void ab8500_chargalg_state_to(struct ab8500_chargalg *di, 307 enum ab8500_chargalg_states state) 308{ 309 dev_dbg(di->dev, 310 "State changed: %s (From state: [%d] %s =to=> [%d] %s )\n", 311 di->charge_state == state ? "NO" : "YES", 312 di->charge_state, 313 states[di->charge_state], 314 state, 315 states[state]); 316 317 di->charge_state = state; 318} 319 320static int ab8500_chargalg_check_charger_enable(struct ab8500_chargalg *di) 321{ 322 struct power_supply_battery_info *bi = di->bm->bi; 323 324 switch (di->charge_state) { 325 case STATE_NORMAL: 326 case STATE_MAINTENANCE_A: 327 case STATE_MAINTENANCE_B: 328 break; 329 default: 330 return 0; 331 } 332 333 if (di->chg_info.charger_type & USB_CHG) { 334 return di->usb_chg->ops.check_enable(di->usb_chg, 335 bi->constant_charge_voltage_max_uv, 336 bi->constant_charge_current_max_ua); 337 } else if (di->chg_info.charger_type & AC_CHG) { 338 return di->ac_chg->ops.check_enable(di->ac_chg, 339 bi->constant_charge_voltage_max_uv, 340 bi->constant_charge_current_max_ua); 341 } 342 return 0; 343} 344 345/** 346 * ab8500_chargalg_check_charger_connection() - Check charger connection change 347 * @di: pointer to the ab8500_chargalg structure 348 * 349 * This function will check if there is a change in the charger connection 350 * and change charge state accordingly. AC has precedence over USB. 351 */ 352static int ab8500_chargalg_check_charger_connection(struct ab8500_chargalg *di) 353{ 354 if (di->chg_info.conn_chg != di->chg_info.prev_conn_chg) { 355 /* Charger state changed since last update */ 356 if (di->chg_info.conn_chg & AC_CHG) { 357 dev_info(di->dev, "Charging source is AC\n"); 358 if (di->chg_info.charger_type != AC_CHG) { 359 di->chg_info.charger_type = AC_CHG; 360 ab8500_chargalg_state_to(di, STATE_NORMAL_INIT); 361 } 362 } else if (di->chg_info.conn_chg & USB_CHG) { 363 dev_info(di->dev, "Charging source is USB\n"); 364 di->chg_info.charger_type = USB_CHG; 365 ab8500_chargalg_state_to(di, STATE_NORMAL_INIT); 366 } else { 367 dev_dbg(di->dev, "Charging source is OFF\n"); 368 di->chg_info.charger_type = NO_CHG; 369 ab8500_chargalg_state_to(di, STATE_HANDHELD_INIT); 370 } 371 di->chg_info.prev_conn_chg = di->chg_info.conn_chg; 372 } 373 return di->chg_info.conn_chg; 374} 375 376/** 377 * ab8500_chargalg_start_safety_timer() - Start charging safety timer 378 * @di: pointer to the ab8500_chargalg structure 379 * 380 * The safety timer is used to avoid overcharging of old or bad batteries. 381 * There are different timers for AC and USB 382 */ 383static void ab8500_chargalg_start_safety_timer(struct ab8500_chargalg *di) 384{ 385 /* Charger-dependent expiration time in hours*/ 386 int timer_expiration = 0; 387 388 switch (di->chg_info.charger_type) { 389 case AC_CHG: 390 timer_expiration = di->bm->main_safety_tmr_h; 391 break; 392 393 case USB_CHG: 394 timer_expiration = di->bm->usb_safety_tmr_h; 395 break; 396 397 default: 398 dev_err(di->dev, "Unknown charger to charge from\n"); 399 break; 400 } 401 402 di->events.safety_timer_expired = false; 403 hrtimer_set_expires_range(&di->safety_timer, 404 ktime_set(timer_expiration * ONE_HOUR_IN_SECONDS, 0), 405 ktime_set(FIVE_MINUTES_IN_SECONDS, 0)); 406 hrtimer_start_expires(&di->safety_timer, HRTIMER_MODE_REL); 407} 408 409/** 410 * ab8500_chargalg_stop_safety_timer() - Stop charging safety timer 411 * @di: pointer to the ab8500_chargalg structure 412 * 413 * The safety timer is stopped whenever the NORMAL state is exited 414 */ 415static void ab8500_chargalg_stop_safety_timer(struct ab8500_chargalg *di) 416{ 417 if (hrtimer_try_to_cancel(&di->safety_timer) >= 0) 418 di->events.safety_timer_expired = false; 419} 420 421/** 422 * ab8500_chargalg_start_maintenance_timer() - Start charging maintenance timer 423 * @di: pointer to the ab8500_chargalg structure 424 * @duration: duration of the maintenance timer in minutes 425 * 426 * The maintenance timer is used to maintain the charge in the battery once 427 * the battery is considered full. These timers are chosen to match the 428 * discharge curve of the battery 429 */ 430static void ab8500_chargalg_start_maintenance_timer(struct ab8500_chargalg *di, 431 int duration) 432{ 433 /* Set a timer in minutes with a 30 second range */ 434 hrtimer_set_expires_range(&di->maintenance_timer, 435 ktime_set(duration * 60, 0), 436 ktime_set(30, 0)); 437 di->events.maintenance_timer_expired = false; 438 hrtimer_start_expires(&di->maintenance_timer, HRTIMER_MODE_REL); 439} 440 441/** 442 * ab8500_chargalg_stop_maintenance_timer() - Stop maintenance timer 443 * @di: pointer to the ab8500_chargalg structure 444 * 445 * The maintenance timer is stopped whenever maintenance ends or when another 446 * state is entered 447 */ 448static void ab8500_chargalg_stop_maintenance_timer(struct ab8500_chargalg *di) 449{ 450 if (hrtimer_try_to_cancel(&di->maintenance_timer) >= 0) 451 di->events.maintenance_timer_expired = false; 452} 453 454/** 455 * ab8500_chargalg_kick_watchdog() - Kick charger watchdog 456 * @di: pointer to the ab8500_chargalg structure 457 * 458 * The charger watchdog have to be kicked periodically whenever the charger is 459 * on, else the ABB will reset the system 460 */ 461static int ab8500_chargalg_kick_watchdog(struct ab8500_chargalg *di) 462{ 463 /* Check if charger exists and kick watchdog if charging */ 464 if (di->ac_chg && di->ac_chg->ops.kick_wd && 465 di->chg_info.online_chg & AC_CHG) { 466 return di->ac_chg->ops.kick_wd(di->ac_chg); 467 } else if (di->usb_chg && di->usb_chg->ops.kick_wd && 468 di->chg_info.online_chg & USB_CHG) 469 return di->usb_chg->ops.kick_wd(di->usb_chg); 470 471 return -ENXIO; 472} 473 474/** 475 * ab8500_chargalg_ac_en() - Turn on/off the AC charger 476 * @di: pointer to the ab8500_chargalg structure 477 * @enable: charger on/off 478 * @vset_uv: requested charger output voltage in microvolt 479 * @iset_ua: requested charger output current in microampere 480 * 481 * The AC charger will be turned on/off with the requested charge voltage and 482 * current 483 */ 484static int ab8500_chargalg_ac_en(struct ab8500_chargalg *di, int enable, 485 int vset_uv, int iset_ua) 486{ 487 if (!di->ac_chg || !di->ac_chg->ops.enable) 488 return -ENXIO; 489 490 /* Select maximum of what both the charger and the battery supports */ 491 if (di->ac_chg->max_out_volt_uv) 492 vset_uv = min(vset_uv, di->ac_chg->max_out_volt_uv); 493 if (di->ac_chg->max_out_curr_ua) 494 iset_ua = min(iset_ua, di->ac_chg->max_out_curr_ua); 495 496 di->chg_info.ac_iset_ua = iset_ua; 497 di->chg_info.ac_vset_uv = vset_uv; 498 499 return di->ac_chg->ops.enable(di->ac_chg, enable, vset_uv, iset_ua); 500} 501 502/** 503 * ab8500_chargalg_usb_en() - Turn on/off the USB charger 504 * @di: pointer to the ab8500_chargalg structure 505 * @enable: charger on/off 506 * @vset_uv: requested charger output voltage in microvolt 507 * @iset_ua: requested charger output current in microampere 508 * 509 * The USB charger will be turned on/off with the requested charge voltage and 510 * current 511 */ 512static int ab8500_chargalg_usb_en(struct ab8500_chargalg *di, int enable, 513 int vset_uv, int iset_ua) 514{ 515 if (!di->usb_chg || !di->usb_chg->ops.enable) 516 return -ENXIO; 517 518 /* Select maximum of what both the charger and the battery supports */ 519 if (di->usb_chg->max_out_volt_uv) 520 vset_uv = min(vset_uv, di->usb_chg->max_out_volt_uv); 521 if (di->usb_chg->max_out_curr_ua) 522 iset_ua = min(iset_ua, di->usb_chg->max_out_curr_ua); 523 524 di->chg_info.usb_iset_ua = iset_ua; 525 di->chg_info.usb_vset_uv = vset_uv; 526 527 return di->usb_chg->ops.enable(di->usb_chg, enable, vset_uv, iset_ua); 528} 529 530/** 531 * ab8500_chargalg_update_chg_curr() - Update charger current 532 * @di: pointer to the ab8500_chargalg structure 533 * @iset_ua: requested charger output current in microampere 534 * 535 * The charger output current will be updated for the charger 536 * that is currently in use 537 */ 538static int ab8500_chargalg_update_chg_curr(struct ab8500_chargalg *di, 539 int iset_ua) 540{ 541 /* Check if charger exists and update current if charging */ 542 if (di->ac_chg && di->ac_chg->ops.update_curr && 543 di->chg_info.charger_type & AC_CHG) { 544 /* 545 * Select maximum of what both the charger 546 * and the battery supports 547 */ 548 if (di->ac_chg->max_out_curr_ua) 549 iset_ua = min(iset_ua, di->ac_chg->max_out_curr_ua); 550 551 di->chg_info.ac_iset_ua = iset_ua; 552 553 return di->ac_chg->ops.update_curr(di->ac_chg, iset_ua); 554 } else if (di->usb_chg && di->usb_chg->ops.update_curr && 555 di->chg_info.charger_type & USB_CHG) { 556 /* 557 * Select maximum of what both the charger 558 * and the battery supports 559 */ 560 if (di->usb_chg->max_out_curr_ua) 561 iset_ua = min(iset_ua, di->usb_chg->max_out_curr_ua); 562 563 di->chg_info.usb_iset_ua = iset_ua; 564 565 return di->usb_chg->ops.update_curr(di->usb_chg, iset_ua); 566 } 567 568 return -ENXIO; 569} 570 571/** 572 * ab8500_chargalg_stop_charging() - Stop charging 573 * @di: pointer to the ab8500_chargalg structure 574 * 575 * This function is called from any state where charging should be stopped. 576 * All charging is disabled and all status parameters and timers are changed 577 * accordingly 578 */ 579static void ab8500_chargalg_stop_charging(struct ab8500_chargalg *di) 580{ 581 ab8500_chargalg_ac_en(di, false, 0, 0); 582 ab8500_chargalg_usb_en(di, false, 0, 0); 583 ab8500_chargalg_stop_safety_timer(di); 584 ab8500_chargalg_stop_maintenance_timer(di); 585 di->charge_status = POWER_SUPPLY_STATUS_NOT_CHARGING; 586 di->maintenance_chg = false; 587 cancel_delayed_work(&di->chargalg_wd_work); 588 power_supply_changed(di->chargalg_psy); 589} 590 591/** 592 * ab8500_chargalg_hold_charging() - Pauses charging 593 * @di: pointer to the ab8500_chargalg structure 594 * 595 * This function is called in the case where maintenance charging has been 596 * disabled and instead a battery voltage mode is entered to check when the 597 * battery voltage has reached a certain recharge voltage 598 */ 599static void ab8500_chargalg_hold_charging(struct ab8500_chargalg *di) 600{ 601 ab8500_chargalg_ac_en(di, false, 0, 0); 602 ab8500_chargalg_usb_en(di, false, 0, 0); 603 ab8500_chargalg_stop_safety_timer(di); 604 ab8500_chargalg_stop_maintenance_timer(di); 605 di->charge_status = POWER_SUPPLY_STATUS_CHARGING; 606 di->maintenance_chg = false; 607 cancel_delayed_work(&di->chargalg_wd_work); 608 power_supply_changed(di->chargalg_psy); 609} 610 611/** 612 * ab8500_chargalg_start_charging() - Start the charger 613 * @di: pointer to the ab8500_chargalg structure 614 * @vset_uv: requested charger output voltage in microvolt 615 * @iset_ua: requested charger output current in microampere 616 * 617 * A charger will be enabled depending on the requested charger type that was 618 * detected previously. 619 */ 620static void ab8500_chargalg_start_charging(struct ab8500_chargalg *di, 621 int vset_uv, int iset_ua) 622{ 623 switch (di->chg_info.charger_type) { 624 case AC_CHG: 625 dev_dbg(di->dev, 626 "AC parameters: Vset %d, Ich %d\n", vset_uv, iset_ua); 627 ab8500_chargalg_usb_en(di, false, 0, 0); 628 ab8500_chargalg_ac_en(di, true, vset_uv, iset_ua); 629 break; 630 631 case USB_CHG: 632 dev_dbg(di->dev, 633 "USB parameters: Vset %d, Ich %d\n", vset_uv, iset_ua); 634 ab8500_chargalg_ac_en(di, false, 0, 0); 635 ab8500_chargalg_usb_en(di, true, vset_uv, iset_ua); 636 break; 637 638 default: 639 dev_err(di->dev, "Unknown charger to charge from\n"); 640 break; 641 } 642} 643 644/** 645 * ab8500_chargalg_check_temp() - Check battery temperature ranges 646 * @di: pointer to the ab8500_chargalg structure 647 * 648 * The battery temperature is checked against the predefined limits and the 649 * charge state is changed accordingly 650 */ 651static void ab8500_chargalg_check_temp(struct ab8500_chargalg *di) 652{ 653 struct power_supply_battery_info *bi = di->bm->bi; 654 655 if (di->batt_data.temp > (bi->temp_alert_min + di->t_hyst_norm) && 656 di->batt_data.temp < (bi->temp_alert_max - di->t_hyst_norm)) { 657 /* Temp OK! */ 658 di->events.btemp_underover = false; 659 di->events.btemp_low = false; 660 di->events.btemp_high = false; 661 di->t_hyst_norm = 0; 662 di->t_hyst_lowhigh = 0; 663 } else { 664 if ((di->batt_data.temp >= bi->temp_alert_max) && 665 (di->batt_data.temp < (bi->temp_max - di->t_hyst_lowhigh))) { 666 /* Alert zone for high temperature */ 667 di->events.btemp_underover = false; 668 di->events.btemp_high = true; 669 di->t_hyst_norm = di->bm->temp_hysteresis; 670 di->t_hyst_lowhigh = 0; 671 } else if ((di->batt_data.temp > (bi->temp_min + di->t_hyst_lowhigh)) && 672 (di->batt_data.temp <= bi->temp_alert_min)) { 673 /* Alert zone for low temperature */ 674 di->events.btemp_underover = false; 675 di->events.btemp_low = true; 676 di->t_hyst_norm = di->bm->temp_hysteresis; 677 di->t_hyst_lowhigh = 0; 678 } else if (di->batt_data.temp <= bi->temp_min || 679 di->batt_data.temp >= bi->temp_max) { 680 /* TEMP major!!!!! */ 681 di->events.btemp_underover = true; 682 di->events.btemp_low = false; 683 di->events.btemp_high = false; 684 di->t_hyst_norm = 0; 685 di->t_hyst_lowhigh = di->bm->temp_hysteresis; 686 } else { 687 /* Within hysteresis */ 688 dev_dbg(di->dev, "Within hysteresis limit temp: %d " 689 "hyst_lowhigh %d, hyst normal %d\n", 690 di->batt_data.temp, di->t_hyst_lowhigh, 691 di->t_hyst_norm); 692 } 693 } 694} 695 696/** 697 * ab8500_chargalg_check_charger_voltage() - Check charger voltage 698 * @di: pointer to the ab8500_chargalg structure 699 * 700 * Charger voltage is checked against maximum limit 701 */ 702static void ab8500_chargalg_check_charger_voltage(struct ab8500_chargalg *di) 703{ 704 if (di->chg_info.usb_volt_uv > di->bm->chg_params->usb_volt_max_uv) 705 di->chg_info.usb_chg_ok = false; 706 else 707 di->chg_info.usb_chg_ok = true; 708 709 if (di->chg_info.ac_volt_uv > di->bm->chg_params->ac_volt_max_uv) 710 di->chg_info.ac_chg_ok = false; 711 else 712 di->chg_info.ac_chg_ok = true; 713 714} 715 716/** 717 * ab8500_chargalg_end_of_charge() - Check if end-of-charge criteria is fulfilled 718 * @di: pointer to the ab8500_chargalg structure 719 * 720 * End-of-charge criteria is fulfilled when the battery voltage is above a 721 * certain limit and the battery current is below a certain limit for a 722 * predefined number of consecutive seconds. If true, the battery is full 723 */ 724static void ab8500_chargalg_end_of_charge(struct ab8500_chargalg *di) 725{ 726 if (di->charge_status == POWER_SUPPLY_STATUS_CHARGING && 727 di->charge_state == STATE_NORMAL && 728 !di->maintenance_chg && (di->batt_data.volt_uv >= 729 di->bm->bi->voltage_max_design_uv || 730 di->events.usb_cv_active || di->events.ac_cv_active) && 731 di->batt_data.avg_curr_ua < 732 di->bm->bi->charge_term_current_ua && 733 di->batt_data.avg_curr_ua > 0) { 734 if (++di->eoc_cnt >= EOC_COND_CNT) { 735 di->eoc_cnt = 0; 736 di->charge_status = POWER_SUPPLY_STATUS_FULL; 737 di->maintenance_chg = true; 738 dev_dbg(di->dev, "EOC reached!\n"); 739 power_supply_changed(di->chargalg_psy); 740 } else { 741 dev_dbg(di->dev, 742 " EOC limit reached for the %d" 743 " time, out of %d before EOC\n", 744 di->eoc_cnt, 745 EOC_COND_CNT); 746 } 747 } else { 748 di->eoc_cnt = 0; 749 } 750} 751 752static void init_maxim_chg_curr(struct ab8500_chargalg *di) 753{ 754 struct power_supply_battery_info *bi = di->bm->bi; 755 756 di->ccm.original_iset_ua = bi->constant_charge_current_max_ua; 757 di->ccm.current_iset_ua = bi->constant_charge_current_max_ua; 758 di->ccm.max_current_ua = di->bm->maxi->chg_curr_ua; 759 di->ccm.condition_cnt = di->bm->maxi->wait_cycles; 760 di->ccm.level = 0; 761} 762 763/** 764 * ab8500_chargalg_chg_curr_maxim - increases the charger current to 765 * compensate for the system load 766 * @di pointer to the ab8500_chargalg structure 767 * 768 * This maximization function is used to raise the charger current to get the 769 * battery current as close to the optimal value as possible. The battery 770 * current during charging is affected by the system load 771 */ 772static enum maxim_ret ab8500_chargalg_chg_curr_maxim(struct ab8500_chargalg *di) 773{ 774 775 if (!di->bm->maxi->ena_maxi) 776 return MAXIM_RET_NOACTION; 777 778 if (di->events.vbus_collapsed) { 779 dev_dbg(di->dev, "Charger voltage has collapsed %d\n", 780 di->ccm.wait_cnt); 781 if (di->ccm.wait_cnt == 0) { 782 dev_dbg(di->dev, "lowering current\n"); 783 di->ccm.wait_cnt++; 784 di->ccm.condition_cnt = di->bm->maxi->wait_cycles; 785 di->ccm.max_current_ua = di->ccm.current_iset_ua; 786 di->ccm.current_iset_ua = di->ccm.max_current_ua; 787 di->ccm.level--; 788 return MAXIM_RET_CHANGE; 789 } else { 790 dev_dbg(di->dev, "waiting\n"); 791 /* Let's go in here twice before lowering curr again */ 792 di->ccm.wait_cnt = (di->ccm.wait_cnt + 1) % 3; 793 return MAXIM_RET_NOACTION; 794 } 795 } 796 797 di->ccm.wait_cnt = 0; 798 799 if (di->batt_data.inst_curr_ua > di->ccm.original_iset_ua) { 800 dev_dbg(di->dev, " Maximization Ibat (%duA) too high" 801 " (limit %duA) (current iset: %duA)!\n", 802 di->batt_data.inst_curr_ua, di->ccm.original_iset_ua, 803 di->ccm.current_iset_ua); 804 805 if (di->ccm.current_iset_ua == di->ccm.original_iset_ua) 806 return MAXIM_RET_NOACTION; 807 808 di->ccm.condition_cnt = di->bm->maxi->wait_cycles; 809 di->ccm.current_iset_ua = di->ccm.original_iset_ua; 810 di->ccm.level = 0; 811 812 return MAXIM_RET_IBAT_TOO_HIGH; 813 } 814 815 di->ccm.condition_cnt = di->bm->maxi->wait_cycles; 816 return MAXIM_RET_NOACTION; 817} 818 819static void handle_maxim_chg_curr(struct ab8500_chargalg *di) 820{ 821 struct power_supply_battery_info *bi = di->bm->bi; 822 enum maxim_ret ret; 823 int result; 824 825 ret = ab8500_chargalg_chg_curr_maxim(di); 826 switch (ret) { 827 case MAXIM_RET_CHANGE: 828 result = ab8500_chargalg_update_chg_curr(di, 829 di->ccm.current_iset_ua); 830 if (result) 831 dev_err(di->dev, "failed to set chg curr\n"); 832 break; 833 case MAXIM_RET_IBAT_TOO_HIGH: 834 result = ab8500_chargalg_update_chg_curr(di, 835 bi->constant_charge_current_max_ua); 836 if (result) 837 dev_err(di->dev, "failed to set chg curr\n"); 838 break; 839 840 case MAXIM_RET_NOACTION: 841 default: 842 /* Do nothing..*/ 843 break; 844 } 845} 846 847static int ab8500_chargalg_get_ext_psy_data(struct device *dev, void *data) 848{ 849 struct power_supply *psy; 850 struct power_supply *ext = dev_get_drvdata(dev); 851 const char **supplicants = (const char **)ext->supplied_to; 852 struct ab8500_chargalg *di; 853 union power_supply_propval ret; 854 int j; 855 bool capacity_updated = false; 856 857 psy = (struct power_supply *)data; 858 di = power_supply_get_drvdata(psy); 859 /* For all psy where the driver name appears in any supplied_to */ 860 j = match_string(supplicants, ext->num_supplicants, psy->desc->name); 861 if (j < 0) 862 return 0; 863 864 /* 865 * If external is not registering 'POWER_SUPPLY_PROP_CAPACITY' to its 866 * property because of handling that sysfs entry on its own, this is 867 * the place to get the battery capacity. 868 */ 869 if (!power_supply_get_property(ext, POWER_SUPPLY_PROP_CAPACITY, &ret)) { 870 di->batt_data.percent = ret.intval; 871 capacity_updated = true; 872 } 873 874 /* Go through all properties for the psy */ 875 for (j = 0; j < ext->desc->num_properties; j++) { 876 enum power_supply_property prop; 877 prop = ext->desc->properties[j]; 878 879 /* 880 * Initialize chargers if not already done. 881 * The ab8500_charger*/ 882 if (!di->ac_chg && 883 ext->desc->type == POWER_SUPPLY_TYPE_MAINS) 884 di->ac_chg = psy_to_ux500_charger(ext); 885 else if (!di->usb_chg && 886 ext->desc->type == POWER_SUPPLY_TYPE_USB) 887 di->usb_chg = psy_to_ux500_charger(ext); 888 889 if (power_supply_get_property(ext, prop, &ret)) 890 continue; 891 switch (prop) { 892 case POWER_SUPPLY_PROP_PRESENT: 893 switch (ext->desc->type) { 894 case POWER_SUPPLY_TYPE_BATTERY: 895 /* Battery present */ 896 if (ret.intval) 897 di->events.batt_rem = false; 898 /* Battery removed */ 899 else 900 di->events.batt_rem = true; 901 break; 902 case POWER_SUPPLY_TYPE_MAINS: 903 /* AC disconnected */ 904 if (!ret.intval && 905 (di->chg_info.conn_chg & AC_CHG)) { 906 di->chg_info.prev_conn_chg = 907 di->chg_info.conn_chg; 908 di->chg_info.conn_chg &= ~AC_CHG; 909 } 910 /* AC connected */ 911 else if (ret.intval && 912 !(di->chg_info.conn_chg & AC_CHG)) { 913 di->chg_info.prev_conn_chg = 914 di->chg_info.conn_chg; 915 di->chg_info.conn_chg |= AC_CHG; 916 } 917 break; 918 case POWER_SUPPLY_TYPE_USB: 919 /* USB disconnected */ 920 if (!ret.intval && 921 (di->chg_info.conn_chg & USB_CHG)) { 922 di->chg_info.prev_conn_chg = 923 di->chg_info.conn_chg; 924 di->chg_info.conn_chg &= ~USB_CHG; 925 } 926 /* USB connected */ 927 else if (ret.intval && 928 !(di->chg_info.conn_chg & USB_CHG)) { 929 di->chg_info.prev_conn_chg = 930 di->chg_info.conn_chg; 931 di->chg_info.conn_chg |= USB_CHG; 932 } 933 break; 934 default: 935 break; 936 } 937 break; 938 939 case POWER_SUPPLY_PROP_ONLINE: 940 switch (ext->desc->type) { 941 case POWER_SUPPLY_TYPE_BATTERY: 942 break; 943 case POWER_SUPPLY_TYPE_MAINS: 944 /* AC offline */ 945 if (!ret.intval && 946 (di->chg_info.online_chg & AC_CHG)) { 947 di->chg_info.prev_online_chg = 948 di->chg_info.online_chg; 949 di->chg_info.online_chg &= ~AC_CHG; 950 } 951 /* AC online */ 952 else if (ret.intval && 953 !(di->chg_info.online_chg & AC_CHG)) { 954 di->chg_info.prev_online_chg = 955 di->chg_info.online_chg; 956 di->chg_info.online_chg |= AC_CHG; 957 queue_delayed_work(di->chargalg_wq, 958 &di->chargalg_wd_work, 0); 959 } 960 break; 961 case POWER_SUPPLY_TYPE_USB: 962 /* USB offline */ 963 if (!ret.intval && 964 (di->chg_info.online_chg & USB_CHG)) { 965 di->chg_info.prev_online_chg = 966 di->chg_info.online_chg; 967 di->chg_info.online_chg &= ~USB_CHG; 968 } 969 /* USB online */ 970 else if (ret.intval && 971 !(di->chg_info.online_chg & USB_CHG)) { 972 di->chg_info.prev_online_chg = 973 di->chg_info.online_chg; 974 di->chg_info.online_chg |= USB_CHG; 975 queue_delayed_work(di->chargalg_wq, 976 &di->chargalg_wd_work, 0); 977 } 978 break; 979 default: 980 break; 981 } 982 break; 983 984 case POWER_SUPPLY_PROP_HEALTH: 985 switch (ext->desc->type) { 986 case POWER_SUPPLY_TYPE_BATTERY: 987 break; 988 case POWER_SUPPLY_TYPE_MAINS: 989 switch (ret.intval) { 990 case POWER_SUPPLY_HEALTH_UNSPEC_FAILURE: 991 di->events.mainextchnotok = true; 992 di->events.main_thermal_prot = false; 993 di->events.main_ovv = false; 994 di->events.ac_wd_expired = false; 995 break; 996 case POWER_SUPPLY_HEALTH_DEAD: 997 di->events.ac_wd_expired = true; 998 di->events.mainextchnotok = false; 999 di->events.main_ovv = false; 1000 di->events.main_thermal_prot = false; 1001 break; 1002 case POWER_SUPPLY_HEALTH_COLD: 1003 case POWER_SUPPLY_HEALTH_OVERHEAT: 1004 di->events.main_thermal_prot = true; 1005 di->events.mainextchnotok = false; 1006 di->events.main_ovv = false; 1007 di->events.ac_wd_expired = false; 1008 break; 1009 case POWER_SUPPLY_HEALTH_OVERVOLTAGE: 1010 di->events.main_ovv = true; 1011 di->events.mainextchnotok = false; 1012 di->events.main_thermal_prot = false; 1013 di->events.ac_wd_expired = false; 1014 break; 1015 case POWER_SUPPLY_HEALTH_GOOD: 1016 di->events.main_thermal_prot = false; 1017 di->events.mainextchnotok = false; 1018 di->events.main_ovv = false; 1019 di->events.ac_wd_expired = false; 1020 break; 1021 default: 1022 break; 1023 } 1024 break; 1025 1026 case POWER_SUPPLY_TYPE_USB: 1027 switch (ret.intval) { 1028 case POWER_SUPPLY_HEALTH_UNSPEC_FAILURE: 1029 di->events.usbchargernotok = true; 1030 di->events.usb_thermal_prot = false; 1031 di->events.vbus_ovv = false; 1032 di->events.usb_wd_expired = false; 1033 break; 1034 case POWER_SUPPLY_HEALTH_DEAD: 1035 di->events.usb_wd_expired = true; 1036 di->events.usbchargernotok = false; 1037 di->events.usb_thermal_prot = false; 1038 di->events.vbus_ovv = false; 1039 break; 1040 case POWER_SUPPLY_HEALTH_COLD: 1041 case POWER_SUPPLY_HEALTH_OVERHEAT: 1042 di->events.usb_thermal_prot = true; 1043 di->events.usbchargernotok = false; 1044 di->events.vbus_ovv = false; 1045 di->events.usb_wd_expired = false; 1046 break; 1047 case POWER_SUPPLY_HEALTH_OVERVOLTAGE: 1048 di->events.vbus_ovv = true; 1049 di->events.usbchargernotok = false; 1050 di->events.usb_thermal_prot = false; 1051 di->events.usb_wd_expired = false; 1052 break; 1053 case POWER_SUPPLY_HEALTH_GOOD: 1054 di->events.usbchargernotok = false; 1055 di->events.usb_thermal_prot = false; 1056 di->events.vbus_ovv = false; 1057 di->events.usb_wd_expired = false; 1058 break; 1059 default: 1060 break; 1061 } 1062 break; 1063 default: 1064 break; 1065 } 1066 break; 1067 1068 case POWER_SUPPLY_PROP_VOLTAGE_NOW: 1069 switch (ext->desc->type) { 1070 case POWER_SUPPLY_TYPE_BATTERY: 1071 di->batt_data.volt_uv = ret.intval; 1072 break; 1073 case POWER_SUPPLY_TYPE_MAINS: 1074 di->chg_info.ac_volt_uv = ret.intval; 1075 break; 1076 case POWER_SUPPLY_TYPE_USB: 1077 di->chg_info.usb_volt_uv = ret.intval; 1078 break; 1079 default: 1080 break; 1081 } 1082 break; 1083 1084 case POWER_SUPPLY_PROP_VOLTAGE_AVG: 1085 switch (ext->desc->type) { 1086 case POWER_SUPPLY_TYPE_MAINS: 1087 /* AVG is used to indicate when we are 1088 * in CV mode */ 1089 if (ret.intval) 1090 di->events.ac_cv_active = true; 1091 else 1092 di->events.ac_cv_active = false; 1093 1094 break; 1095 case POWER_SUPPLY_TYPE_USB: 1096 /* AVG is used to indicate when we are 1097 * in CV mode */ 1098 if (ret.intval) 1099 di->events.usb_cv_active = true; 1100 else 1101 di->events.usb_cv_active = false; 1102 1103 break; 1104 default: 1105 break; 1106 } 1107 break; 1108 1109 case POWER_SUPPLY_PROP_TECHNOLOGY: 1110 switch (ext->desc->type) { 1111 case POWER_SUPPLY_TYPE_BATTERY: 1112 if (ret.intval) 1113 di->events.batt_unknown = false; 1114 else 1115 di->events.batt_unknown = true; 1116 1117 break; 1118 default: 1119 break; 1120 } 1121 break; 1122 1123 case POWER_SUPPLY_PROP_TEMP: 1124 di->batt_data.temp = ret.intval / 10; 1125 break; 1126 1127 case POWER_SUPPLY_PROP_CURRENT_NOW: 1128 switch (ext->desc->type) { 1129 case POWER_SUPPLY_TYPE_MAINS: 1130 di->chg_info.ac_curr_ua = ret.intval; 1131 break; 1132 case POWER_SUPPLY_TYPE_USB: 1133 di->chg_info.usb_curr_ua = ret.intval; 1134 break; 1135 case POWER_SUPPLY_TYPE_BATTERY: 1136 di->batt_data.inst_curr_ua = ret.intval; 1137 break; 1138 default: 1139 break; 1140 } 1141 break; 1142 1143 case POWER_SUPPLY_PROP_CURRENT_AVG: 1144 switch (ext->desc->type) { 1145 case POWER_SUPPLY_TYPE_BATTERY: 1146 di->batt_data.avg_curr_ua = ret.intval; 1147 break; 1148 case POWER_SUPPLY_TYPE_USB: 1149 if (ret.intval) 1150 di->events.vbus_collapsed = true; 1151 else 1152 di->events.vbus_collapsed = false; 1153 break; 1154 default: 1155 break; 1156 } 1157 break; 1158 case POWER_SUPPLY_PROP_CAPACITY: 1159 if (!capacity_updated) 1160 di->batt_data.percent = ret.intval; 1161 break; 1162 default: 1163 break; 1164 } 1165 } 1166 return 0; 1167} 1168 1169/** 1170 * ab8500_chargalg_external_power_changed() - callback for power supply changes 1171 * @psy: pointer to the structure power_supply 1172 * 1173 * This function is the entry point of the pointer external_power_changed 1174 * of the structure power_supply. 1175 * This function gets executed when there is a change in any external power 1176 * supply that this driver needs to be notified of. 1177 */ 1178static void ab8500_chargalg_external_power_changed(struct power_supply *psy) 1179{ 1180 struct ab8500_chargalg *di = power_supply_get_drvdata(psy); 1181 1182 /* 1183 * Trigger execution of the algorithm instantly and read 1184 * all power_supply properties there instead 1185 */ 1186 if (di->chargalg_wq) 1187 queue_work(di->chargalg_wq, &di->chargalg_work); 1188} 1189 1190/** 1191 * ab8500_chargalg_time_to_restart() - time to restart CC/CV charging? 1192 * @di: charging algorithm state 1193 * 1194 * This checks if the voltage or capacity of the battery has fallen so 1195 * low that we need to restart the CC/CV charge cycle. 1196 */ 1197static bool ab8500_chargalg_time_to_restart(struct ab8500_chargalg *di) 1198{ 1199 struct power_supply_battery_info *bi = di->bm->bi; 1200 1201 /* Sanity check - these need to have some reasonable values */ 1202 if (!di->batt_data.volt_uv || !di->batt_data.percent) 1203 return false; 1204 1205 /* Some batteries tell us at which voltage we should restart charging */ 1206 if (bi->charge_restart_voltage_uv > 0) { 1207 if (di->batt_data.volt_uv <= bi->charge_restart_voltage_uv) 1208 return true; 1209 /* Else we restart as we reach a certain capacity */ 1210 } else { 1211 if (di->batt_data.percent <= AB8500_RECHARGE_CAP) 1212 return true; 1213 } 1214 1215 return false; 1216} 1217 1218/** 1219 * ab8500_chargalg_algorithm() - Main function for the algorithm 1220 * @di: pointer to the ab8500_chargalg structure 1221 * 1222 * This is the main control function for the charging algorithm. 1223 * It is called periodically or when something happens that will 1224 * trigger a state change 1225 */ 1226static void ab8500_chargalg_algorithm(struct ab8500_chargalg *di) 1227{ 1228 struct power_supply_battery_info *bi = di->bm->bi; 1229 struct power_supply_maintenance_charge_table *mt; 1230 int charger_status; 1231 int ret; 1232 1233 /* Collect data from all power_supply class devices */ 1234 power_supply_for_each_device(di->chargalg_psy, ab8500_chargalg_get_ext_psy_data); 1235 1236 ab8500_chargalg_end_of_charge(di); 1237 ab8500_chargalg_check_temp(di); 1238 ab8500_chargalg_check_charger_voltage(di); 1239 1240 charger_status = ab8500_chargalg_check_charger_connection(di); 1241 1242 if (is_ab8500(di->parent)) { 1243 ret = ab8500_chargalg_check_charger_enable(di); 1244 if (ret < 0) 1245 dev_err(di->dev, "Checking charger is enabled error" 1246 ": Returned Value %d\n", ret); 1247 } 1248 1249 /* 1250 * First check if we have a charger connected. 1251 * Also we don't allow charging of unknown batteries if configured 1252 * this way 1253 */ 1254 if (!charger_status || 1255 (di->events.batt_unknown && !di->bm->chg_unknown_bat)) { 1256 if (di->charge_state != STATE_HANDHELD) { 1257 di->events.safety_timer_expired = false; 1258 ab8500_chargalg_state_to(di, STATE_HANDHELD_INIT); 1259 } 1260 } 1261 1262 /* Safety timer expiration */ 1263 else if (di->events.safety_timer_expired) { 1264 if (di->charge_state != STATE_SAFETY_TIMER_EXPIRED) 1265 ab8500_chargalg_state_to(di, 1266 STATE_SAFETY_TIMER_EXPIRED_INIT); 1267 } 1268 /* 1269 * Check if any interrupts has occurred 1270 * that will prevent us from charging 1271 */ 1272 1273 /* Battery removed */ 1274 else if (di->events.batt_rem) { 1275 if (di->charge_state != STATE_BATT_REMOVED) 1276 ab8500_chargalg_state_to(di, STATE_BATT_REMOVED_INIT); 1277 } 1278 /* Main or USB charger not ok. */ 1279 else if (di->events.mainextchnotok || di->events.usbchargernotok) { 1280 /* 1281 * If vbus_collapsed is set, we have to lower the charger 1282 * current, which is done in the normal state below 1283 */ 1284 if (di->charge_state != STATE_CHG_NOT_OK && 1285 !di->events.vbus_collapsed) 1286 ab8500_chargalg_state_to(di, STATE_CHG_NOT_OK_INIT); 1287 } 1288 /* VBUS, Main or VBAT OVV. */ 1289 else if (di->events.vbus_ovv || 1290 di->events.main_ovv || 1291 di->events.batt_ovv || 1292 !di->chg_info.usb_chg_ok || 1293 !di->chg_info.ac_chg_ok) { 1294 if (di->charge_state != STATE_OVV_PROTECT) 1295 ab8500_chargalg_state_to(di, STATE_OVV_PROTECT_INIT); 1296 } 1297 /* USB Thermal, stop charging */ 1298 else if (di->events.main_thermal_prot || 1299 di->events.usb_thermal_prot) { 1300 if (di->charge_state != STATE_HW_TEMP_PROTECT) 1301 ab8500_chargalg_state_to(di, 1302 STATE_HW_TEMP_PROTECT_INIT); 1303 } 1304 /* Battery temp over/under */ 1305 else if (di->events.btemp_underover) { 1306 if (di->charge_state != STATE_TEMP_UNDEROVER) 1307 ab8500_chargalg_state_to(di, 1308 STATE_TEMP_UNDEROVER_INIT); 1309 } 1310 /* Watchdog expired */ 1311 else if (di->events.ac_wd_expired || 1312 di->events.usb_wd_expired) { 1313 if (di->charge_state != STATE_WD_EXPIRED) 1314 ab8500_chargalg_state_to(di, STATE_WD_EXPIRED_INIT); 1315 } 1316 /* Battery temp high/low */ 1317 else if (di->events.btemp_low || di->events.btemp_high) { 1318 if (di->charge_state != STATE_TEMP_LOWHIGH) 1319 ab8500_chargalg_state_to(di, STATE_TEMP_LOWHIGH_INIT); 1320 } 1321 1322 dev_dbg(di->dev, 1323 "[CHARGALG] Vb %d Ib_avg %d Ib_inst %d Tb %d Cap %d Maint %d " 1324 "State %s Active_chg %d Chg_status %d AC %d USB %d " 1325 "AC_online %d USB_online %d AC_CV %d USB_CV %d AC_I %d " 1326 "USB_I %d AC_Vset %d AC_Iset %d USB_Vset %d USB_Iset %d\n", 1327 di->batt_data.volt_uv, 1328 di->batt_data.avg_curr_ua, 1329 di->batt_data.inst_curr_ua, 1330 di->batt_data.temp, 1331 di->batt_data.percent, 1332 di->maintenance_chg, 1333 states[di->charge_state], 1334 di->chg_info.charger_type, 1335 di->charge_status, 1336 di->chg_info.conn_chg & AC_CHG, 1337 di->chg_info.conn_chg & USB_CHG, 1338 di->chg_info.online_chg & AC_CHG, 1339 di->chg_info.online_chg & USB_CHG, 1340 di->events.ac_cv_active, 1341 di->events.usb_cv_active, 1342 di->chg_info.ac_curr_ua, 1343 di->chg_info.usb_curr_ua, 1344 di->chg_info.ac_vset_uv, 1345 di->chg_info.ac_iset_ua, 1346 di->chg_info.usb_vset_uv, 1347 di->chg_info.usb_iset_ua); 1348 1349 switch (di->charge_state) { 1350 case STATE_HANDHELD_INIT: 1351 ab8500_chargalg_stop_charging(di); 1352 di->charge_status = POWER_SUPPLY_STATUS_DISCHARGING; 1353 ab8500_chargalg_state_to(di, STATE_HANDHELD); 1354 fallthrough; 1355 1356 case STATE_HANDHELD: 1357 break; 1358 1359 case STATE_BATT_REMOVED_INIT: 1360 ab8500_chargalg_stop_charging(di); 1361 ab8500_chargalg_state_to(di, STATE_BATT_REMOVED); 1362 fallthrough; 1363 1364 case STATE_BATT_REMOVED: 1365 if (!di->events.batt_rem) 1366 ab8500_chargalg_state_to(di, STATE_NORMAL_INIT); 1367 break; 1368 1369 case STATE_HW_TEMP_PROTECT_INIT: 1370 ab8500_chargalg_stop_charging(di); 1371 ab8500_chargalg_state_to(di, STATE_HW_TEMP_PROTECT); 1372 fallthrough; 1373 1374 case STATE_HW_TEMP_PROTECT: 1375 if (!di->events.main_thermal_prot && 1376 !di->events.usb_thermal_prot) 1377 ab8500_chargalg_state_to(di, STATE_NORMAL_INIT); 1378 break; 1379 1380 case STATE_OVV_PROTECT_INIT: 1381 ab8500_chargalg_stop_charging(di); 1382 ab8500_chargalg_state_to(di, STATE_OVV_PROTECT); 1383 fallthrough; 1384 1385 case STATE_OVV_PROTECT: 1386 if (!di->events.vbus_ovv && 1387 !di->events.main_ovv && 1388 !di->events.batt_ovv && 1389 di->chg_info.usb_chg_ok && 1390 di->chg_info.ac_chg_ok) 1391 ab8500_chargalg_state_to(di, STATE_NORMAL_INIT); 1392 break; 1393 1394 case STATE_CHG_NOT_OK_INIT: 1395 ab8500_chargalg_stop_charging(di); 1396 ab8500_chargalg_state_to(di, STATE_CHG_NOT_OK); 1397 fallthrough; 1398 1399 case STATE_CHG_NOT_OK: 1400 if (!di->events.mainextchnotok && 1401 !di->events.usbchargernotok) 1402 ab8500_chargalg_state_to(di, STATE_NORMAL_INIT); 1403 break; 1404 1405 case STATE_SAFETY_TIMER_EXPIRED_INIT: 1406 ab8500_chargalg_stop_charging(di); 1407 ab8500_chargalg_state_to(di, STATE_SAFETY_TIMER_EXPIRED); 1408 fallthrough; 1409 1410 case STATE_SAFETY_TIMER_EXPIRED: 1411 /* We exit this state when charger is removed */ 1412 break; 1413 1414 case STATE_NORMAL_INIT: 1415 if (bi->constant_charge_current_max_ua == 0) 1416 /* "charging" with 0 uA */ 1417 ab8500_chargalg_stop_charging(di); 1418 else { 1419 ab8500_chargalg_start_charging(di, 1420 bi->constant_charge_voltage_max_uv, 1421 bi->constant_charge_current_max_ua); 1422 } 1423 1424 ab8500_chargalg_state_to(di, STATE_NORMAL); 1425 ab8500_chargalg_start_safety_timer(di); 1426 ab8500_chargalg_stop_maintenance_timer(di); 1427 init_maxim_chg_curr(di); 1428 di->charge_status = POWER_SUPPLY_STATUS_CHARGING; 1429 di->eoc_cnt = 0; 1430 di->maintenance_chg = false; 1431 power_supply_changed(di->chargalg_psy); 1432 1433 break; 1434 1435 case STATE_NORMAL: 1436 handle_maxim_chg_curr(di); 1437 if (di->charge_status == POWER_SUPPLY_STATUS_FULL && 1438 di->maintenance_chg) { 1439 /* 1440 * The battery is fully charged, check if we support 1441 * maintenance charging else go back to waiting for 1442 * the recharge voltage limit. 1443 */ 1444 if (!power_supply_supports_maintenance_charging(bi)) 1445 ab8500_chargalg_state_to(di, 1446 STATE_WAIT_FOR_RECHARGE_INIT); 1447 else 1448 ab8500_chargalg_state_to(di, 1449 STATE_MAINTENANCE_A_INIT); 1450 } 1451 break; 1452 1453 /* This state will be used when the maintenance state is disabled */ 1454 case STATE_WAIT_FOR_RECHARGE_INIT: 1455 ab8500_chargalg_hold_charging(di); 1456 ab8500_chargalg_state_to(di, STATE_WAIT_FOR_RECHARGE); 1457 fallthrough; 1458 1459 case STATE_WAIT_FOR_RECHARGE: 1460 if (ab8500_chargalg_time_to_restart(di)) 1461 ab8500_chargalg_state_to(di, STATE_NORMAL_INIT); 1462 break; 1463 1464 case STATE_MAINTENANCE_A_INIT: 1465 mt = power_supply_get_maintenance_charging_setting(bi, 0); 1466 if (!mt) { 1467 /* No maintenance A state, go back to normal */ 1468 ab8500_chargalg_state_to(di, STATE_NORMAL_INIT); 1469 power_supply_changed(di->chargalg_psy); 1470 break; 1471 } 1472 ab8500_chargalg_stop_safety_timer(di); 1473 ab8500_chargalg_start_maintenance_timer(di, 1474 mt->charge_safety_timer_minutes); 1475 ab8500_chargalg_start_charging(di, 1476 mt->charge_voltage_max_uv, 1477 mt->charge_current_max_ua); 1478 ab8500_chargalg_state_to(di, STATE_MAINTENANCE_A); 1479 power_supply_changed(di->chargalg_psy); 1480 fallthrough; 1481 1482 case STATE_MAINTENANCE_A: 1483 if (di->events.maintenance_timer_expired) { 1484 ab8500_chargalg_stop_maintenance_timer(di); 1485 ab8500_chargalg_state_to(di, STATE_MAINTENANCE_B_INIT); 1486 } 1487 /* 1488 * This happens if the voltage drops too quickly during 1489 * maintenance charging, especially in older batteries. 1490 */ 1491 if (ab8500_chargalg_time_to_restart(di)) { 1492 ab8500_chargalg_state_to(di, STATE_NORMAL_INIT); 1493 dev_info(di->dev, "restarted charging from maintenance state A - battery getting old?\n"); 1494 } 1495 break; 1496 1497 case STATE_MAINTENANCE_B_INIT: 1498 mt = power_supply_get_maintenance_charging_setting(bi, 1); 1499 if (!mt) { 1500 /* No maintenance B state, go back to normal */ 1501 ab8500_chargalg_state_to(di, STATE_NORMAL_INIT); 1502 power_supply_changed(di->chargalg_psy); 1503 break; 1504 } 1505 ab8500_chargalg_start_maintenance_timer(di, 1506 mt->charge_safety_timer_minutes); 1507 ab8500_chargalg_start_charging(di, 1508 mt->charge_voltage_max_uv, 1509 mt->charge_current_max_ua); 1510 ab8500_chargalg_state_to(di, STATE_MAINTENANCE_B); 1511 power_supply_changed(di->chargalg_psy); 1512 fallthrough; 1513 1514 case STATE_MAINTENANCE_B: 1515 if (di->events.maintenance_timer_expired) { 1516 ab8500_chargalg_stop_maintenance_timer(di); 1517 ab8500_chargalg_state_to(di, STATE_NORMAL_INIT); 1518 } 1519 /* 1520 * This happens if the voltage drops too quickly during 1521 * maintenance charging, especially in older batteries. 1522 */ 1523 if (ab8500_chargalg_time_to_restart(di)) { 1524 ab8500_chargalg_state_to(di, STATE_NORMAL_INIT); 1525 dev_info(di->dev, "restarted charging from maintenance state B - battery getting old?\n"); 1526 } 1527 break; 1528 1529 case STATE_TEMP_LOWHIGH_INIT: 1530 if (di->events.btemp_low) { 1531 ab8500_chargalg_start_charging(di, 1532 bi->alert_low_temp_charge_voltage_uv, 1533 bi->alert_low_temp_charge_current_ua); 1534 } else if (di->events.btemp_high) { 1535 ab8500_chargalg_start_charging(di, 1536 bi->alert_high_temp_charge_voltage_uv, 1537 bi->alert_high_temp_charge_current_ua); 1538 } else { 1539 dev_err(di->dev, "neither low or high temp event occurred\n"); 1540 ab8500_chargalg_state_to(di, STATE_NORMAL_INIT); 1541 break; 1542 } 1543 ab8500_chargalg_stop_maintenance_timer(di); 1544 di->charge_status = POWER_SUPPLY_STATUS_CHARGING; 1545 ab8500_chargalg_state_to(di, STATE_TEMP_LOWHIGH); 1546 power_supply_changed(di->chargalg_psy); 1547 fallthrough; 1548 1549 case STATE_TEMP_LOWHIGH: 1550 if (!di->events.btemp_low && !di->events.btemp_high) 1551 ab8500_chargalg_state_to(di, STATE_NORMAL_INIT); 1552 break; 1553 1554 case STATE_WD_EXPIRED_INIT: 1555 ab8500_chargalg_stop_charging(di); 1556 ab8500_chargalg_state_to(di, STATE_WD_EXPIRED); 1557 fallthrough; 1558 1559 case STATE_WD_EXPIRED: 1560 if (!di->events.ac_wd_expired && 1561 !di->events.usb_wd_expired) 1562 ab8500_chargalg_state_to(di, STATE_NORMAL_INIT); 1563 break; 1564 1565 case STATE_TEMP_UNDEROVER_INIT: 1566 ab8500_chargalg_stop_charging(di); 1567 ab8500_chargalg_state_to(di, STATE_TEMP_UNDEROVER); 1568 fallthrough; 1569 1570 case STATE_TEMP_UNDEROVER: 1571 if (!di->events.btemp_underover) 1572 ab8500_chargalg_state_to(di, STATE_NORMAL_INIT); 1573 break; 1574 } 1575 1576 /* Start charging directly if the new state is a charge state */ 1577 if (di->charge_state == STATE_NORMAL_INIT || 1578 di->charge_state == STATE_MAINTENANCE_A_INIT || 1579 di->charge_state == STATE_MAINTENANCE_B_INIT) 1580 queue_work(di->chargalg_wq, &di->chargalg_work); 1581} 1582 1583/** 1584 * ab8500_chargalg_periodic_work() - Periodic work for the algorithm 1585 * @work: pointer to the work_struct structure 1586 * 1587 * Work queue function for the charging algorithm 1588 */ 1589static void ab8500_chargalg_periodic_work(struct work_struct *work) 1590{ 1591 struct ab8500_chargalg *di = container_of(work, 1592 struct ab8500_chargalg, chargalg_periodic_work.work); 1593 1594 ab8500_chargalg_algorithm(di); 1595 1596 /* 1597 * If a charger is connected then the battery has to be monitored 1598 * frequently, else the work can be delayed. 1599 */ 1600 if (di->chg_info.conn_chg) 1601 queue_delayed_work(di->chargalg_wq, 1602 &di->chargalg_periodic_work, 1603 di->bm->interval_charging * HZ); 1604 else 1605 queue_delayed_work(di->chargalg_wq, 1606 &di->chargalg_periodic_work, 1607 di->bm->interval_not_charging * HZ); 1608} 1609 1610/** 1611 * ab8500_chargalg_wd_work() - periodic work to kick the charger watchdog 1612 * @work: pointer to the work_struct structure 1613 * 1614 * Work queue function for kicking the charger watchdog 1615 */ 1616static void ab8500_chargalg_wd_work(struct work_struct *work) 1617{ 1618 int ret; 1619 struct ab8500_chargalg *di = container_of(work, 1620 struct ab8500_chargalg, chargalg_wd_work.work); 1621 1622 ret = ab8500_chargalg_kick_watchdog(di); 1623 if (ret < 0) 1624 dev_err(di->dev, "failed to kick watchdog\n"); 1625 1626 queue_delayed_work(di->chargalg_wq, 1627 &di->chargalg_wd_work, CHG_WD_INTERVAL); 1628} 1629 1630/** 1631 * ab8500_chargalg_work() - Work to run the charging algorithm instantly 1632 * @work: pointer to the work_struct structure 1633 * 1634 * Work queue function for calling the charging algorithm 1635 */ 1636static void ab8500_chargalg_work(struct work_struct *work) 1637{ 1638 struct ab8500_chargalg *di = container_of(work, 1639 struct ab8500_chargalg, chargalg_work); 1640 1641 ab8500_chargalg_algorithm(di); 1642} 1643 1644/** 1645 * ab8500_chargalg_get_property() - get the chargalg properties 1646 * @psy: pointer to the power_supply structure 1647 * @psp: pointer to the power_supply_property structure 1648 * @val: pointer to the power_supply_propval union 1649 * 1650 * This function gets called when an application tries to get the 1651 * chargalg properties by reading the sysfs files. 1652 * status: charging/discharging/full/unknown 1653 * health: health of the battery 1654 * Returns error code in case of failure else 0 on success 1655 */ 1656static int ab8500_chargalg_get_property(struct power_supply *psy, 1657 enum power_supply_property psp, 1658 union power_supply_propval *val) 1659{ 1660 struct ab8500_chargalg *di = power_supply_get_drvdata(psy); 1661 1662 switch (psp) { 1663 case POWER_SUPPLY_PROP_STATUS: 1664 val->intval = di->charge_status; 1665 break; 1666 case POWER_SUPPLY_PROP_HEALTH: 1667 if (di->events.batt_ovv) { 1668 val->intval = POWER_SUPPLY_HEALTH_OVERVOLTAGE; 1669 } else if (di->events.btemp_underover) { 1670 if (di->batt_data.temp <= di->bm->bi->temp_min) 1671 val->intval = POWER_SUPPLY_HEALTH_COLD; 1672 else 1673 val->intval = POWER_SUPPLY_HEALTH_OVERHEAT; 1674 } else if (di->charge_state == STATE_SAFETY_TIMER_EXPIRED || 1675 di->charge_state == STATE_SAFETY_TIMER_EXPIRED_INIT) { 1676 val->intval = POWER_SUPPLY_HEALTH_UNSPEC_FAILURE; 1677 } else { 1678 val->intval = POWER_SUPPLY_HEALTH_GOOD; 1679 } 1680 break; 1681 default: 1682 return -EINVAL; 1683 } 1684 return 0; 1685} 1686 1687static int __maybe_unused ab8500_chargalg_resume(struct device *dev) 1688{ 1689 struct ab8500_chargalg *di = dev_get_drvdata(dev); 1690 1691 /* Kick charger watchdog if charging (any charger online) */ 1692 if (di->chg_info.online_chg) 1693 queue_delayed_work(di->chargalg_wq, &di->chargalg_wd_work, 0); 1694 1695 /* 1696 * Run the charging algorithm directly to be sure we don't 1697 * do it too seldom 1698 */ 1699 queue_delayed_work(di->chargalg_wq, &di->chargalg_periodic_work, 0); 1700 1701 return 0; 1702} 1703 1704static int __maybe_unused ab8500_chargalg_suspend(struct device *dev) 1705{ 1706 struct ab8500_chargalg *di = dev_get_drvdata(dev); 1707 1708 if (di->chg_info.online_chg) 1709 cancel_delayed_work_sync(&di->chargalg_wd_work); 1710 1711 cancel_delayed_work_sync(&di->chargalg_periodic_work); 1712 1713 return 0; 1714} 1715 1716static char *supply_interface[] = { 1717 "ab8500_fg", 1718}; 1719 1720static const struct power_supply_desc ab8500_chargalg_desc = { 1721 .name = "ab8500_chargalg", 1722 .type = POWER_SUPPLY_TYPE_UNKNOWN, 1723 .properties = ab8500_chargalg_props, 1724 .num_properties = ARRAY_SIZE(ab8500_chargalg_props), 1725 .get_property = ab8500_chargalg_get_property, 1726 .external_power_changed = ab8500_chargalg_external_power_changed, 1727}; 1728 1729static int ab8500_chargalg_bind(struct device *dev, struct device *master, 1730 void *data) 1731{ 1732 struct ab8500_chargalg *di = dev_get_drvdata(dev); 1733 1734 /* Create a work queue for the chargalg */ 1735 di->chargalg_wq = alloc_ordered_workqueue("ab8500_chargalg_wq", 1736 WQ_MEM_RECLAIM); 1737 if (di->chargalg_wq == NULL) { 1738 dev_err(di->dev, "failed to create work queue\n"); 1739 return -ENOMEM; 1740 } 1741 1742 /* Run the charging algorithm */ 1743 queue_delayed_work(di->chargalg_wq, &di->chargalg_periodic_work, 0); 1744 1745 return 0; 1746} 1747 1748static void ab8500_chargalg_unbind(struct device *dev, struct device *master, 1749 void *data) 1750{ 1751 struct ab8500_chargalg *di = dev_get_drvdata(dev); 1752 1753 /* Stop all timers and work */ 1754 hrtimer_cancel(&di->safety_timer); 1755 hrtimer_cancel(&di->maintenance_timer); 1756 1757 cancel_delayed_work_sync(&di->chargalg_periodic_work); 1758 cancel_delayed_work_sync(&di->chargalg_wd_work); 1759 cancel_work_sync(&di->chargalg_work); 1760 1761 /* Delete the work queue */ 1762 destroy_workqueue(di->chargalg_wq); 1763} 1764 1765static const struct component_ops ab8500_chargalg_component_ops = { 1766 .bind = ab8500_chargalg_bind, 1767 .unbind = ab8500_chargalg_unbind, 1768}; 1769 1770static int ab8500_chargalg_probe(struct platform_device *pdev) 1771{ 1772 struct device *dev = &pdev->dev; 1773 struct power_supply_config psy_cfg = {}; 1774 struct ab8500_chargalg *di; 1775 1776 di = devm_kzalloc(dev, sizeof(*di), GFP_KERNEL); 1777 if (!di) 1778 return -ENOMEM; 1779 1780 di->bm = &ab8500_bm_data; 1781 1782 /* get device struct and parent */ 1783 di->dev = dev; 1784 di->parent = dev_get_drvdata(pdev->dev.parent); 1785 1786 psy_cfg.supplied_to = supply_interface; 1787 psy_cfg.num_supplicants = ARRAY_SIZE(supply_interface); 1788 psy_cfg.drv_data = di; 1789 1790 /* Initilialize safety timer */ 1791 hrtimer_init(&di->safety_timer, CLOCK_MONOTONIC, HRTIMER_MODE_REL); 1792 di->safety_timer.function = ab8500_chargalg_safety_timer_expired; 1793 1794 /* Initilialize maintenance timer */ 1795 hrtimer_init(&di->maintenance_timer, CLOCK_MONOTONIC, HRTIMER_MODE_REL); 1796 di->maintenance_timer.function = 1797 ab8500_chargalg_maintenance_timer_expired; 1798 1799 /* Init work for chargalg */ 1800 INIT_DEFERRABLE_WORK(&di->chargalg_periodic_work, 1801 ab8500_chargalg_periodic_work); 1802 INIT_DEFERRABLE_WORK(&di->chargalg_wd_work, 1803 ab8500_chargalg_wd_work); 1804 1805 /* Init work for chargalg */ 1806 INIT_WORK(&di->chargalg_work, ab8500_chargalg_work); 1807 1808 /* To detect charger at startup */ 1809 di->chg_info.prev_conn_chg = -1; 1810 1811 /* Register chargalg power supply class */ 1812 di->chargalg_psy = devm_power_supply_register(di->dev, 1813 &ab8500_chargalg_desc, 1814 &psy_cfg); 1815 if (IS_ERR(di->chargalg_psy)) { 1816 dev_err(di->dev, "failed to register chargalg psy\n"); 1817 return PTR_ERR(di->chargalg_psy); 1818 } 1819 1820 platform_set_drvdata(pdev, di); 1821 1822 dev_info(di->dev, "probe success\n"); 1823 return component_add(dev, &ab8500_chargalg_component_ops); 1824} 1825 1826static void ab8500_chargalg_remove(struct platform_device *pdev) 1827{ 1828 component_del(&pdev->dev, &ab8500_chargalg_component_ops); 1829} 1830 1831static SIMPLE_DEV_PM_OPS(ab8500_chargalg_pm_ops, ab8500_chargalg_suspend, ab8500_chargalg_resume); 1832 1833static const struct of_device_id ab8500_chargalg_match[] = { 1834 { .compatible = "stericsson,ab8500-chargalg", }, 1835 { }, 1836}; 1837 1838struct platform_driver ab8500_chargalg_driver = { 1839 .probe = ab8500_chargalg_probe, 1840 .remove_new = ab8500_chargalg_remove, 1841 .driver = { 1842 .name = "ab8500_chargalg", 1843 .of_match_table = ab8500_chargalg_match, 1844 .pm = &ab8500_chargalg_pm_ops, 1845 }, 1846}; 1847MODULE_LICENSE("GPL v2"); 1848MODULE_AUTHOR("Johan Palsson, Karl Komierowski"); 1849MODULE_ALIAS("platform:ab8500-chargalg"); 1850MODULE_DESCRIPTION("ab8500 battery charging algorithm"); 1851