1// SPDX-License-Identifier: GPL-2.0-only 2/* drivers/net/ethernet/micrel/ks8851.c 3 * 4 * Copyright 2009 Simtec Electronics 5 * http://www.simtec.co.uk/ 6 * Ben Dooks <ben@simtec.co.uk> 7 */ 8 9#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt 10 11#include <linux/interrupt.h> 12#include <linux/module.h> 13#include <linux/kernel.h> 14#include <linux/netdevice.h> 15#include <linux/etherdevice.h> 16#include <linux/ethtool.h> 17#include <linux/cache.h> 18#include <linux/crc32.h> 19#include <linux/mii.h> 20#include <linux/gpio/consumer.h> 21#include <linux/regulator/consumer.h> 22 23#include <linux/of_mdio.h> 24#include <linux/of_net.h> 25 26#include "ks8851.h" 27 28/** 29 * ks8851_lock - register access lock 30 * @ks: The chip state 31 * @flags: Spinlock flags 32 * 33 * Claim chip register access lock 34 */ 35static void ks8851_lock(struct ks8851_net *ks, unsigned long *flags) 36{ 37 ks->lock(ks, flags); 38} 39 40/** 41 * ks8851_unlock - register access unlock 42 * @ks: The chip state 43 * @flags: Spinlock flags 44 * 45 * Release chip register access lock 46 */ 47static void ks8851_unlock(struct ks8851_net *ks, unsigned long *flags) 48{ 49 ks->unlock(ks, flags); 50} 51 52/** 53 * ks8851_wrreg16 - write 16bit register value to chip 54 * @ks: The chip state 55 * @reg: The register address 56 * @val: The value to write 57 * 58 * Issue a write to put the value @val into the register specified in @reg. 59 */ 60static void ks8851_wrreg16(struct ks8851_net *ks, unsigned int reg, 61 unsigned int val) 62{ 63 ks->wrreg16(ks, reg, val); 64} 65 66/** 67 * ks8851_rdreg16 - read 16 bit register from device 68 * @ks: The chip information 69 * @reg: The register address 70 * 71 * Read a 16bit register from the chip, returning the result 72 */ 73static unsigned int ks8851_rdreg16(struct ks8851_net *ks, 74 unsigned int reg) 75{ 76 return ks->rdreg16(ks, reg); 77} 78 79/** 80 * ks8851_soft_reset - issue one of the soft reset to the device 81 * @ks: The device state. 82 * @op: The bit(s) to set in the GRR 83 * 84 * Issue the relevant soft-reset command to the device's GRR register 85 * specified by @op. 86 * 87 * Note, the delays are in there as a caution to ensure that the reset 88 * has time to take effect and then complete. Since the datasheet does 89 * not currently specify the exact sequence, we have chosen something 90 * that seems to work with our device. 91 */ 92static void ks8851_soft_reset(struct ks8851_net *ks, unsigned op) 93{ 94 ks8851_wrreg16(ks, KS_GRR, op); 95 mdelay(1); /* wait a short time to effect reset */ 96 ks8851_wrreg16(ks, KS_GRR, 0); 97 mdelay(1); /* wait for condition to clear */ 98} 99 100/** 101 * ks8851_set_powermode - set power mode of the device 102 * @ks: The device state 103 * @pwrmode: The power mode value to write to KS_PMECR. 104 * 105 * Change the power mode of the chip. 106 */ 107static void ks8851_set_powermode(struct ks8851_net *ks, unsigned pwrmode) 108{ 109 unsigned pmecr; 110 111 netif_dbg(ks, hw, ks->netdev, "setting power mode %d\n", pwrmode); 112 113 pmecr = ks8851_rdreg16(ks, KS_PMECR); 114 pmecr &= ~PMECR_PM_MASK; 115 pmecr |= pwrmode; 116 117 ks8851_wrreg16(ks, KS_PMECR, pmecr); 118} 119 120/** 121 * ks8851_write_mac_addr - write mac address to device registers 122 * @dev: The network device 123 * 124 * Update the KS8851 MAC address registers from the address in @dev. 125 * 126 * This call assumes that the chip is not running, so there is no need to 127 * shutdown the RXQ process whilst setting this. 128*/ 129static int ks8851_write_mac_addr(struct net_device *dev) 130{ 131 struct ks8851_net *ks = netdev_priv(dev); 132 unsigned long flags; 133 u16 val; 134 int i; 135 136 ks8851_lock(ks, &flags); 137 138 /* 139 * Wake up chip in case it was powered off when stopped; otherwise, 140 * the first write to the MAC address does not take effect. 141 */ 142 ks8851_set_powermode(ks, PMECR_PM_NORMAL); 143 144 for (i = 0; i < ETH_ALEN; i += 2) { 145 val = (dev->dev_addr[i] << 8) | dev->dev_addr[i + 1]; 146 ks8851_wrreg16(ks, KS_MAR(i), val); 147 } 148 149 if (!netif_running(dev)) 150 ks8851_set_powermode(ks, PMECR_PM_SOFTDOWN); 151 152 ks8851_unlock(ks, &flags); 153 154 return 0; 155} 156 157/** 158 * ks8851_read_mac_addr - read mac address from device registers 159 * @dev: The network device 160 * 161 * Update our copy of the KS8851 MAC address from the registers of @dev. 162*/ 163static void ks8851_read_mac_addr(struct net_device *dev) 164{ 165 struct ks8851_net *ks = netdev_priv(dev); 166 unsigned long flags; 167 u8 addr[ETH_ALEN]; 168 u16 reg; 169 int i; 170 171 ks8851_lock(ks, &flags); 172 173 for (i = 0; i < ETH_ALEN; i += 2) { 174 reg = ks8851_rdreg16(ks, KS_MAR(i)); 175 addr[i] = reg >> 8; 176 addr[i + 1] = reg & 0xff; 177 } 178 eth_hw_addr_set(dev, addr); 179 180 ks8851_unlock(ks, &flags); 181} 182 183/** 184 * ks8851_init_mac - initialise the mac address 185 * @ks: The device structure 186 * @np: The device node pointer 187 * 188 * Get or create the initial mac address for the device and then set that 189 * into the station address register. A mac address supplied in the device 190 * tree takes precedence. Otherwise, if there is an EEPROM present, then 191 * we try that. If no valid mac address is found we use eth_random_addr() 192 * to create a new one. 193 */ 194static void ks8851_init_mac(struct ks8851_net *ks, struct device_node *np) 195{ 196 struct net_device *dev = ks->netdev; 197 int ret; 198 199 ret = of_get_ethdev_address(np, dev); 200 if (!ret) { 201 ks8851_write_mac_addr(dev); 202 return; 203 } 204 205 if (ks->rc_ccr & CCR_EEPROM) { 206 ks8851_read_mac_addr(dev); 207 if (is_valid_ether_addr(dev->dev_addr)) 208 return; 209 210 netdev_err(ks->netdev, "invalid mac address read %pM\n", 211 dev->dev_addr); 212 } 213 214 eth_hw_addr_random(dev); 215 ks8851_write_mac_addr(dev); 216} 217 218/** 219 * ks8851_dbg_dumpkkt - dump initial packet contents to debug 220 * @ks: The device state 221 * @rxpkt: The data for the received packet 222 * 223 * Dump the initial data from the packet to dev_dbg(). 224 */ 225static void ks8851_dbg_dumpkkt(struct ks8851_net *ks, u8 *rxpkt) 226{ 227 netdev_dbg(ks->netdev, 228 "pkt %02x%02x%02x%02x %02x%02x%02x%02x %02x%02x%02x%02x\n", 229 rxpkt[4], rxpkt[5], rxpkt[6], rxpkt[7], 230 rxpkt[8], rxpkt[9], rxpkt[10], rxpkt[11], 231 rxpkt[12], rxpkt[13], rxpkt[14], rxpkt[15]); 232} 233 234/** 235 * ks8851_rx_pkts - receive packets from the host 236 * @ks: The device information. 237 * 238 * This is called from the IRQ work queue when the system detects that there 239 * are packets in the receive queue. Find out how many packets there are and 240 * read them from the FIFO. 241 */ 242static void ks8851_rx_pkts(struct ks8851_net *ks) 243{ 244 struct sk_buff *skb; 245 unsigned rxfc; 246 unsigned rxlen; 247 unsigned rxstat; 248 u8 *rxpkt; 249 250 rxfc = (ks8851_rdreg16(ks, KS_RXFCTR) >> 8) & 0xff; 251 252 netif_dbg(ks, rx_status, ks->netdev, 253 "%s: %d packets\n", __func__, rxfc); 254 255 /* Currently we're issuing a read per packet, but we could possibly 256 * improve the code by issuing a single read, getting the receive 257 * header, allocating the packet and then reading the packet data 258 * out in one go. 259 * 260 * This form of operation would require us to hold the SPI bus' 261 * chipselect low during the entie transaction to avoid any 262 * reset to the data stream coming from the chip. 263 */ 264 265 for (; rxfc != 0; rxfc--) { 266 rxstat = ks8851_rdreg16(ks, KS_RXFHSR); 267 rxlen = ks8851_rdreg16(ks, KS_RXFHBCR) & RXFHBCR_CNT_MASK; 268 269 netif_dbg(ks, rx_status, ks->netdev, 270 "rx: stat 0x%04x, len 0x%04x\n", rxstat, rxlen); 271 272 /* the length of the packet includes the 32bit CRC */ 273 274 /* set dma read address */ 275 ks8851_wrreg16(ks, KS_RXFDPR, RXFDPR_RXFPAI | 0x00); 276 277 /* start DMA access */ 278 ks8851_wrreg16(ks, KS_RXQCR, ks->rc_rxqcr | RXQCR_SDA); 279 280 if (rxlen > 4) { 281 unsigned int rxalign; 282 283 rxlen -= 4; 284 rxalign = ALIGN(rxlen, 4); 285 skb = netdev_alloc_skb_ip_align(ks->netdev, rxalign); 286 if (skb) { 287 288 /* 4 bytes of status header + 4 bytes of 289 * garbage: we put them before ethernet 290 * header, so that they are copied, 291 * but ignored. 292 */ 293 294 rxpkt = skb_put(skb, rxlen) - 8; 295 296 ks->rdfifo(ks, rxpkt, rxalign + 8); 297 298 if (netif_msg_pktdata(ks)) 299 ks8851_dbg_dumpkkt(ks, rxpkt); 300 301 skb->protocol = eth_type_trans(skb, ks->netdev); 302 __netif_rx(skb); 303 304 ks->netdev->stats.rx_packets++; 305 ks->netdev->stats.rx_bytes += rxlen; 306 } 307 } 308 309 /* end DMA access and dequeue packet */ 310 ks8851_wrreg16(ks, KS_RXQCR, ks->rc_rxqcr | RXQCR_RRXEF); 311 } 312} 313 314/** 315 * ks8851_irq - IRQ handler for dealing with interrupt requests 316 * @irq: IRQ number 317 * @_ks: cookie 318 * 319 * This handler is invoked when the IRQ line asserts to find out what happened. 320 * As we cannot allow ourselves to sleep in HARDIRQ context, this handler runs 321 * in thread context. 322 * 323 * Read the interrupt status, work out what needs to be done and then clear 324 * any of the interrupts that are not needed. 325 */ 326static irqreturn_t ks8851_irq(int irq, void *_ks) 327{ 328 struct ks8851_net *ks = _ks; 329 unsigned handled = 0; 330 unsigned long flags; 331 unsigned int status; 332 333 local_bh_disable(); 334 335 ks8851_lock(ks, &flags); 336 337 status = ks8851_rdreg16(ks, KS_ISR); 338 339 netif_dbg(ks, intr, ks->netdev, 340 "%s: status 0x%04x\n", __func__, status); 341 342 if (status & IRQ_LCI) 343 handled |= IRQ_LCI; 344 345 if (status & IRQ_LDI) { 346 u16 pmecr = ks8851_rdreg16(ks, KS_PMECR); 347 pmecr &= ~PMECR_WKEVT_MASK; 348 ks8851_wrreg16(ks, KS_PMECR, pmecr | PMECR_WKEVT_LINK); 349 350 handled |= IRQ_LDI; 351 } 352 353 if (status & IRQ_RXPSI) 354 handled |= IRQ_RXPSI; 355 356 if (status & IRQ_TXI) { 357 unsigned short tx_space = ks8851_rdreg16(ks, KS_TXMIR); 358 359 netif_dbg(ks, intr, ks->netdev, 360 "%s: txspace %d\n", __func__, tx_space); 361 362 spin_lock(&ks->statelock); 363 ks->tx_space = tx_space; 364 if (netif_queue_stopped(ks->netdev)) 365 netif_wake_queue(ks->netdev); 366 spin_unlock(&ks->statelock); 367 368 handled |= IRQ_TXI; 369 } 370 371 if (status & IRQ_RXI) 372 handled |= IRQ_RXI; 373 374 if (status & IRQ_SPIBEI) { 375 netdev_err(ks->netdev, "%s: spi bus error\n", __func__); 376 handled |= IRQ_SPIBEI; 377 } 378 379 ks8851_wrreg16(ks, KS_ISR, handled); 380 381 if (status & IRQ_RXI) { 382 /* the datasheet says to disable the rx interrupt during 383 * packet read-out, however we're masking the interrupt 384 * from the device so do not bother masking just the RX 385 * from the device. */ 386 387 ks8851_rx_pkts(ks); 388 } 389 390 /* if something stopped the rx process, probably due to wanting 391 * to change the rx settings, then do something about restarting 392 * it. */ 393 if (status & IRQ_RXPSI) { 394 struct ks8851_rxctrl *rxc = &ks->rxctrl; 395 396 /* update the multicast hash table */ 397 ks8851_wrreg16(ks, KS_MAHTR0, rxc->mchash[0]); 398 ks8851_wrreg16(ks, KS_MAHTR1, rxc->mchash[1]); 399 ks8851_wrreg16(ks, KS_MAHTR2, rxc->mchash[2]); 400 ks8851_wrreg16(ks, KS_MAHTR3, rxc->mchash[3]); 401 402 ks8851_wrreg16(ks, KS_RXCR2, rxc->rxcr2); 403 ks8851_wrreg16(ks, KS_RXCR1, rxc->rxcr1); 404 } 405 406 ks8851_unlock(ks, &flags); 407 408 if (status & IRQ_LCI) 409 mii_check_link(&ks->mii); 410 411 local_bh_enable(); 412 413 return IRQ_HANDLED; 414} 415 416/** 417 * ks8851_flush_tx_work - flush outstanding TX work 418 * @ks: The device state 419 */ 420static void ks8851_flush_tx_work(struct ks8851_net *ks) 421{ 422 if (ks->flush_tx_work) 423 ks->flush_tx_work(ks); 424} 425 426/** 427 * ks8851_net_open - open network device 428 * @dev: The network device being opened. 429 * 430 * Called when the network device is marked active, such as a user executing 431 * 'ifconfig up' on the device. 432 */ 433static int ks8851_net_open(struct net_device *dev) 434{ 435 struct ks8851_net *ks = netdev_priv(dev); 436 unsigned long flags; 437 int ret; 438 439 ret = request_threaded_irq(dev->irq, NULL, ks8851_irq, 440 IRQF_TRIGGER_LOW | IRQF_ONESHOT, 441 dev->name, ks); 442 if (ret < 0) { 443 netdev_err(dev, "failed to get irq\n"); 444 return ret; 445 } 446 447 /* lock the card, even if we may not actually be doing anything 448 * else at the moment */ 449 ks8851_lock(ks, &flags); 450 451 netif_dbg(ks, ifup, ks->netdev, "opening\n"); 452 453 /* bring chip out of any power saving mode it was in */ 454 ks8851_set_powermode(ks, PMECR_PM_NORMAL); 455 456 /* issue a soft reset to the RX/TX QMU to put it into a known 457 * state. */ 458 ks8851_soft_reset(ks, GRR_QMU); 459 460 /* setup transmission parameters */ 461 462 ks8851_wrreg16(ks, KS_TXCR, (TXCR_TXE | /* enable transmit process */ 463 TXCR_TXPE | /* pad to min length */ 464 TXCR_TXCRC | /* add CRC */ 465 TXCR_TXFCE)); /* enable flow control */ 466 467 /* auto-increment tx data, reset tx pointer */ 468 ks8851_wrreg16(ks, KS_TXFDPR, TXFDPR_TXFPAI); 469 470 /* setup receiver control */ 471 472 ks8851_wrreg16(ks, KS_RXCR1, (RXCR1_RXPAFMA | /* from mac filter */ 473 RXCR1_RXFCE | /* enable flow control */ 474 RXCR1_RXBE | /* broadcast enable */ 475 RXCR1_RXUE | /* unicast enable */ 476 RXCR1_RXE)); /* enable rx block */ 477 478 /* transfer entire frames out in one go */ 479 ks8851_wrreg16(ks, KS_RXCR2, RXCR2_SRDBL_FRAME); 480 481 /* set receive counter timeouts */ 482 ks8851_wrreg16(ks, KS_RXDTTR, 1000); /* 1ms after first frame to IRQ */ 483 ks8851_wrreg16(ks, KS_RXDBCTR, 4096); /* >4Kbytes in buffer to IRQ */ 484 ks8851_wrreg16(ks, KS_RXFCTR, 10); /* 10 frames to IRQ */ 485 486 ks->rc_rxqcr = (RXQCR_RXFCTE | /* IRQ on frame count exceeded */ 487 RXQCR_RXDBCTE | /* IRQ on byte count exceeded */ 488 RXQCR_RXDTTE); /* IRQ on time exceeded */ 489 490 ks8851_wrreg16(ks, KS_RXQCR, ks->rc_rxqcr); 491 492 /* clear then enable interrupts */ 493 ks8851_wrreg16(ks, KS_ISR, ks->rc_ier); 494 ks8851_wrreg16(ks, KS_IER, ks->rc_ier); 495 496 ks->queued_len = 0; 497 netif_start_queue(ks->netdev); 498 499 netif_dbg(ks, ifup, ks->netdev, "network device up\n"); 500 501 ks8851_unlock(ks, &flags); 502 mii_check_link(&ks->mii); 503 return 0; 504} 505 506/** 507 * ks8851_net_stop - close network device 508 * @dev: The device being closed. 509 * 510 * Called to close down a network device which has been active. Cancell any 511 * work, shutdown the RX and TX process and then place the chip into a low 512 * power state whilst it is not being used. 513 */ 514static int ks8851_net_stop(struct net_device *dev) 515{ 516 struct ks8851_net *ks = netdev_priv(dev); 517 unsigned long flags; 518 519 netif_info(ks, ifdown, dev, "shutting down\n"); 520 521 netif_stop_queue(dev); 522 523 ks8851_lock(ks, &flags); 524 /* turn off the IRQs and ack any outstanding */ 525 ks8851_wrreg16(ks, KS_IER, 0x0000); 526 ks8851_wrreg16(ks, KS_ISR, 0xffff); 527 ks8851_unlock(ks, &flags); 528 529 /* stop any outstanding work */ 530 ks8851_flush_tx_work(ks); 531 flush_work(&ks->rxctrl_work); 532 533 ks8851_lock(ks, &flags); 534 /* shutdown RX process */ 535 ks8851_wrreg16(ks, KS_RXCR1, 0x0000); 536 537 /* shutdown TX process */ 538 ks8851_wrreg16(ks, KS_TXCR, 0x0000); 539 540 /* set powermode to soft power down to save power */ 541 ks8851_set_powermode(ks, PMECR_PM_SOFTDOWN); 542 ks8851_unlock(ks, &flags); 543 544 /* ensure any queued tx buffers are dumped */ 545 while (!skb_queue_empty(&ks->txq)) { 546 struct sk_buff *txb = skb_dequeue(&ks->txq); 547 548 netif_dbg(ks, ifdown, ks->netdev, 549 "%s: freeing txb %p\n", __func__, txb); 550 551 dev_kfree_skb(txb); 552 } 553 554 free_irq(dev->irq, ks); 555 556 return 0; 557} 558 559/** 560 * ks8851_start_xmit - transmit packet 561 * @skb: The buffer to transmit 562 * @dev: The device used to transmit the packet. 563 * 564 * Called by the network layer to transmit the @skb. Queue the packet for 565 * the device and schedule the necessary work to transmit the packet when 566 * it is free. 567 * 568 * We do this to firstly avoid sleeping with the network device locked, 569 * and secondly so we can round up more than one packet to transmit which 570 * means we can try and avoid generating too many transmit done interrupts. 571 */ 572static netdev_tx_t ks8851_start_xmit(struct sk_buff *skb, 573 struct net_device *dev) 574{ 575 struct ks8851_net *ks = netdev_priv(dev); 576 577 return ks->start_xmit(skb, dev); 578} 579 580/** 581 * ks8851_rxctrl_work - work handler to change rx mode 582 * @work: The work structure this belongs to. 583 * 584 * Lock the device and issue the necessary changes to the receive mode from 585 * the network device layer. This is done so that we can do this without 586 * having to sleep whilst holding the network device lock. 587 * 588 * Since the recommendation from Micrel is that the RXQ is shutdown whilst the 589 * receive parameters are programmed, we issue a write to disable the RXQ and 590 * then wait for the interrupt handler to be triggered once the RXQ shutdown is 591 * complete. The interrupt handler then writes the new values into the chip. 592 */ 593static void ks8851_rxctrl_work(struct work_struct *work) 594{ 595 struct ks8851_net *ks = container_of(work, struct ks8851_net, rxctrl_work); 596 unsigned long flags; 597 598 ks8851_lock(ks, &flags); 599 600 /* need to shutdown RXQ before modifying filter parameters */ 601 ks8851_wrreg16(ks, KS_RXCR1, 0x00); 602 603 ks8851_unlock(ks, &flags); 604} 605 606static void ks8851_set_rx_mode(struct net_device *dev) 607{ 608 struct ks8851_net *ks = netdev_priv(dev); 609 struct ks8851_rxctrl rxctrl; 610 611 memset(&rxctrl, 0, sizeof(rxctrl)); 612 613 if (dev->flags & IFF_PROMISC) { 614 /* interface to receive everything */ 615 616 rxctrl.rxcr1 = RXCR1_RXAE | RXCR1_RXINVF; 617 } else if (dev->flags & IFF_ALLMULTI) { 618 /* accept all multicast packets */ 619 620 rxctrl.rxcr1 = (RXCR1_RXME | RXCR1_RXAE | 621 RXCR1_RXPAFMA | RXCR1_RXMAFMA); 622 } else if (dev->flags & IFF_MULTICAST && !netdev_mc_empty(dev)) { 623 struct netdev_hw_addr *ha; 624 u32 crc; 625 626 /* accept some multicast */ 627 628 netdev_for_each_mc_addr(ha, dev) { 629 crc = ether_crc(ETH_ALEN, ha->addr); 630 crc >>= (32 - 6); /* get top six bits */ 631 632 rxctrl.mchash[crc >> 4] |= (1 << (crc & 0xf)); 633 } 634 635 rxctrl.rxcr1 = RXCR1_RXME | RXCR1_RXPAFMA; 636 } else { 637 /* just accept broadcast / unicast */ 638 rxctrl.rxcr1 = RXCR1_RXPAFMA; 639 } 640 641 rxctrl.rxcr1 |= (RXCR1_RXUE | /* unicast enable */ 642 RXCR1_RXBE | /* broadcast enable */ 643 RXCR1_RXE | /* RX process enable */ 644 RXCR1_RXFCE); /* enable flow control */ 645 646 rxctrl.rxcr2 |= RXCR2_SRDBL_FRAME; 647 648 /* schedule work to do the actual set of the data if needed */ 649 650 spin_lock(&ks->statelock); 651 652 if (memcmp(&rxctrl, &ks->rxctrl, sizeof(rxctrl)) != 0) { 653 memcpy(&ks->rxctrl, &rxctrl, sizeof(ks->rxctrl)); 654 schedule_work(&ks->rxctrl_work); 655 } 656 657 spin_unlock(&ks->statelock); 658} 659 660static int ks8851_set_mac_address(struct net_device *dev, void *addr) 661{ 662 struct sockaddr *sa = addr; 663 664 if (netif_running(dev)) 665 return -EBUSY; 666 667 if (!is_valid_ether_addr(sa->sa_data)) 668 return -EADDRNOTAVAIL; 669 670 eth_hw_addr_set(dev, sa->sa_data); 671 return ks8851_write_mac_addr(dev); 672} 673 674static int ks8851_net_ioctl(struct net_device *dev, struct ifreq *req, int cmd) 675{ 676 struct ks8851_net *ks = netdev_priv(dev); 677 678 if (!netif_running(dev)) 679 return -EINVAL; 680 681 return generic_mii_ioctl(&ks->mii, if_mii(req), cmd, NULL); 682} 683 684static const struct net_device_ops ks8851_netdev_ops = { 685 .ndo_open = ks8851_net_open, 686 .ndo_stop = ks8851_net_stop, 687 .ndo_eth_ioctl = ks8851_net_ioctl, 688 .ndo_start_xmit = ks8851_start_xmit, 689 .ndo_set_mac_address = ks8851_set_mac_address, 690 .ndo_set_rx_mode = ks8851_set_rx_mode, 691 .ndo_validate_addr = eth_validate_addr, 692}; 693 694/* ethtool support */ 695 696static void ks8851_get_drvinfo(struct net_device *dev, 697 struct ethtool_drvinfo *di) 698{ 699 strscpy(di->driver, "KS8851", sizeof(di->driver)); 700 strscpy(di->version, "1.00", sizeof(di->version)); 701 strscpy(di->bus_info, dev_name(dev->dev.parent), sizeof(di->bus_info)); 702} 703 704static u32 ks8851_get_msglevel(struct net_device *dev) 705{ 706 struct ks8851_net *ks = netdev_priv(dev); 707 return ks->msg_enable; 708} 709 710static void ks8851_set_msglevel(struct net_device *dev, u32 to) 711{ 712 struct ks8851_net *ks = netdev_priv(dev); 713 ks->msg_enable = to; 714} 715 716static int ks8851_get_link_ksettings(struct net_device *dev, 717 struct ethtool_link_ksettings *cmd) 718{ 719 struct ks8851_net *ks = netdev_priv(dev); 720 721 mii_ethtool_get_link_ksettings(&ks->mii, cmd); 722 723 return 0; 724} 725 726static int ks8851_set_link_ksettings(struct net_device *dev, 727 const struct ethtool_link_ksettings *cmd) 728{ 729 struct ks8851_net *ks = netdev_priv(dev); 730 return mii_ethtool_set_link_ksettings(&ks->mii, cmd); 731} 732 733static u32 ks8851_get_link(struct net_device *dev) 734{ 735 struct ks8851_net *ks = netdev_priv(dev); 736 return mii_link_ok(&ks->mii); 737} 738 739static int ks8851_nway_reset(struct net_device *dev) 740{ 741 struct ks8851_net *ks = netdev_priv(dev); 742 return mii_nway_restart(&ks->mii); 743} 744 745/* EEPROM support */ 746 747static void ks8851_eeprom_regread(struct eeprom_93cx6 *ee) 748{ 749 struct ks8851_net *ks = ee->data; 750 unsigned val; 751 752 val = ks8851_rdreg16(ks, KS_EEPCR); 753 754 ee->reg_data_out = (val & EEPCR_EESB) ? 1 : 0; 755 ee->reg_data_clock = (val & EEPCR_EESCK) ? 1 : 0; 756 ee->reg_chip_select = (val & EEPCR_EECS) ? 1 : 0; 757} 758 759static void ks8851_eeprom_regwrite(struct eeprom_93cx6 *ee) 760{ 761 struct ks8851_net *ks = ee->data; 762 unsigned val = EEPCR_EESA; /* default - eeprom access on */ 763 764 if (ee->drive_data) 765 val |= EEPCR_EESRWA; 766 if (ee->reg_data_in) 767 val |= EEPCR_EEDO; 768 if (ee->reg_data_clock) 769 val |= EEPCR_EESCK; 770 if (ee->reg_chip_select) 771 val |= EEPCR_EECS; 772 773 ks8851_wrreg16(ks, KS_EEPCR, val); 774} 775 776/** 777 * ks8851_eeprom_claim - claim device EEPROM and activate the interface 778 * @ks: The network device state. 779 * 780 * Check for the presence of an EEPROM, and then activate software access 781 * to the device. 782 */ 783static int ks8851_eeprom_claim(struct ks8851_net *ks) 784{ 785 /* start with clock low, cs high */ 786 ks8851_wrreg16(ks, KS_EEPCR, EEPCR_EESA | EEPCR_EECS); 787 return 0; 788} 789 790/** 791 * ks8851_eeprom_release - release the EEPROM interface 792 * @ks: The device state 793 * 794 * Release the software access to the device EEPROM 795 */ 796static void ks8851_eeprom_release(struct ks8851_net *ks) 797{ 798 unsigned val = ks8851_rdreg16(ks, KS_EEPCR); 799 800 ks8851_wrreg16(ks, KS_EEPCR, val & ~EEPCR_EESA); 801} 802 803#define KS_EEPROM_MAGIC (0x00008851) 804 805static int ks8851_set_eeprom(struct net_device *dev, 806 struct ethtool_eeprom *ee, u8 *data) 807{ 808 struct ks8851_net *ks = netdev_priv(dev); 809 int offset = ee->offset; 810 unsigned long flags; 811 int len = ee->len; 812 u16 tmp; 813 814 /* currently only support byte writing */ 815 if (len != 1) 816 return -EINVAL; 817 818 if (ee->magic != KS_EEPROM_MAGIC) 819 return -EINVAL; 820 821 if (!(ks->rc_ccr & CCR_EEPROM)) 822 return -ENOENT; 823 824 ks8851_lock(ks, &flags); 825 826 ks8851_eeprom_claim(ks); 827 828 eeprom_93cx6_wren(&ks->eeprom, true); 829 830 /* ethtool currently only supports writing bytes, which means 831 * we have to read/modify/write our 16bit EEPROMs */ 832 833 eeprom_93cx6_read(&ks->eeprom, offset/2, &tmp); 834 835 if (offset & 1) { 836 tmp &= 0xff; 837 tmp |= *data << 8; 838 } else { 839 tmp &= 0xff00; 840 tmp |= *data; 841 } 842 843 eeprom_93cx6_write(&ks->eeprom, offset/2, tmp); 844 eeprom_93cx6_wren(&ks->eeprom, false); 845 846 ks8851_eeprom_release(ks); 847 ks8851_unlock(ks, &flags); 848 849 return 0; 850} 851 852static int ks8851_get_eeprom(struct net_device *dev, 853 struct ethtool_eeprom *ee, u8 *data) 854{ 855 struct ks8851_net *ks = netdev_priv(dev); 856 int offset = ee->offset; 857 unsigned long flags; 858 int len = ee->len; 859 860 /* must be 2 byte aligned */ 861 if (len & 1 || offset & 1) 862 return -EINVAL; 863 864 if (!(ks->rc_ccr & CCR_EEPROM)) 865 return -ENOENT; 866 867 ks8851_lock(ks, &flags); 868 869 ks8851_eeprom_claim(ks); 870 871 ee->magic = KS_EEPROM_MAGIC; 872 873 eeprom_93cx6_multiread(&ks->eeprom, offset/2, (__le16 *)data, len/2); 874 ks8851_eeprom_release(ks); 875 ks8851_unlock(ks, &flags); 876 877 return 0; 878} 879 880static int ks8851_get_eeprom_len(struct net_device *dev) 881{ 882 struct ks8851_net *ks = netdev_priv(dev); 883 884 /* currently, we assume it is an 93C46 attached, so return 128 */ 885 return ks->rc_ccr & CCR_EEPROM ? 128 : 0; 886} 887 888static const struct ethtool_ops ks8851_ethtool_ops = { 889 .get_drvinfo = ks8851_get_drvinfo, 890 .get_msglevel = ks8851_get_msglevel, 891 .set_msglevel = ks8851_set_msglevel, 892 .get_link = ks8851_get_link, 893 .nway_reset = ks8851_nway_reset, 894 .get_eeprom_len = ks8851_get_eeprom_len, 895 .get_eeprom = ks8851_get_eeprom, 896 .set_eeprom = ks8851_set_eeprom, 897 .get_link_ksettings = ks8851_get_link_ksettings, 898 .set_link_ksettings = ks8851_set_link_ksettings, 899}; 900 901/* MII interface controls */ 902 903/** 904 * ks8851_phy_reg - convert MII register into a KS8851 register 905 * @reg: MII register number. 906 * 907 * Return the KS8851 register number for the corresponding MII PHY register 908 * if possible. Return zero if the MII register has no direct mapping to the 909 * KS8851 register set. 910 */ 911static int ks8851_phy_reg(int reg) 912{ 913 switch (reg) { 914 case MII_BMCR: 915 return KS_P1MBCR; 916 case MII_BMSR: 917 return KS_P1MBSR; 918 case MII_PHYSID1: 919 return KS_PHY1ILR; 920 case MII_PHYSID2: 921 return KS_PHY1IHR; 922 case MII_ADVERTISE: 923 return KS_P1ANAR; 924 case MII_LPA: 925 return KS_P1ANLPR; 926 } 927 928 return -EOPNOTSUPP; 929} 930 931static int ks8851_phy_read_common(struct net_device *dev, int phy_addr, int reg) 932{ 933 struct ks8851_net *ks = netdev_priv(dev); 934 unsigned long flags; 935 int result; 936 int ksreg; 937 938 ksreg = ks8851_phy_reg(reg); 939 if (ksreg < 0) 940 return ksreg; 941 942 ks8851_lock(ks, &flags); 943 result = ks8851_rdreg16(ks, ksreg); 944 ks8851_unlock(ks, &flags); 945 946 return result; 947} 948 949/** 950 * ks8851_phy_read - MII interface PHY register read. 951 * @dev: The network device the PHY is on. 952 * @phy_addr: Address of PHY (ignored as we only have one) 953 * @reg: The register to read. 954 * 955 * This call reads data from the PHY register specified in @reg. Since the 956 * device does not support all the MII registers, the non-existent values 957 * are always returned as zero. 958 * 959 * We return zero for unsupported registers as the MII code does not check 960 * the value returned for any error status, and simply returns it to the 961 * caller. The mii-tool that the driver was tested with takes any -ve error 962 * as real PHY capabilities, thus displaying incorrect data to the user. 963 */ 964static int ks8851_phy_read(struct net_device *dev, int phy_addr, int reg) 965{ 966 int ret; 967 968 ret = ks8851_phy_read_common(dev, phy_addr, reg); 969 if (ret < 0) 970 return 0x0; /* no error return allowed, so use zero */ 971 972 return ret; 973} 974 975static void ks8851_phy_write(struct net_device *dev, 976 int phy, int reg, int value) 977{ 978 struct ks8851_net *ks = netdev_priv(dev); 979 unsigned long flags; 980 int ksreg; 981 982 ksreg = ks8851_phy_reg(reg); 983 if (ksreg >= 0) { 984 ks8851_lock(ks, &flags); 985 ks8851_wrreg16(ks, ksreg, value); 986 ks8851_unlock(ks, &flags); 987 } 988} 989 990static int ks8851_mdio_read(struct mii_bus *bus, int phy_id, int reg) 991{ 992 struct ks8851_net *ks = bus->priv; 993 994 if (phy_id != 0) 995 return -EOPNOTSUPP; 996 997 /* KS8851 PHY ID registers are swapped in HW, swap them back. */ 998 if (reg == MII_PHYSID1) 999 reg = MII_PHYSID2; 1000 else if (reg == MII_PHYSID2) 1001 reg = MII_PHYSID1; 1002 1003 return ks8851_phy_read_common(ks->netdev, phy_id, reg); 1004} 1005 1006static int ks8851_mdio_write(struct mii_bus *bus, int phy_id, int reg, u16 val) 1007{ 1008 struct ks8851_net *ks = bus->priv; 1009 1010 ks8851_phy_write(ks->netdev, phy_id, reg, val); 1011 return 0; 1012} 1013 1014/** 1015 * ks8851_read_selftest - read the selftest memory info. 1016 * @ks: The device state 1017 * 1018 * Read and check the TX/RX memory selftest information. 1019 */ 1020static void ks8851_read_selftest(struct ks8851_net *ks) 1021{ 1022 unsigned both_done = MBIR_TXMBF | MBIR_RXMBF; 1023 unsigned rd; 1024 1025 rd = ks8851_rdreg16(ks, KS_MBIR); 1026 1027 if ((rd & both_done) != both_done) { 1028 netdev_warn(ks->netdev, "Memory selftest not finished\n"); 1029 return; 1030 } 1031 1032 if (rd & MBIR_TXMBFA) 1033 netdev_err(ks->netdev, "TX memory selftest fail\n"); 1034 1035 if (rd & MBIR_RXMBFA) 1036 netdev_err(ks->netdev, "RX memory selftest fail\n"); 1037} 1038 1039/* driver bus management functions */ 1040 1041#ifdef CONFIG_PM_SLEEP 1042 1043int ks8851_suspend(struct device *dev) 1044{ 1045 struct ks8851_net *ks = dev_get_drvdata(dev); 1046 struct net_device *netdev = ks->netdev; 1047 1048 if (netif_running(netdev)) { 1049 netif_device_detach(netdev); 1050 ks8851_net_stop(netdev); 1051 } 1052 1053 return 0; 1054} 1055EXPORT_SYMBOL_GPL(ks8851_suspend); 1056 1057int ks8851_resume(struct device *dev) 1058{ 1059 struct ks8851_net *ks = dev_get_drvdata(dev); 1060 struct net_device *netdev = ks->netdev; 1061 1062 if (netif_running(netdev)) { 1063 ks8851_net_open(netdev); 1064 netif_device_attach(netdev); 1065 } 1066 1067 return 0; 1068} 1069EXPORT_SYMBOL_GPL(ks8851_resume); 1070#endif 1071 1072static int ks8851_register_mdiobus(struct ks8851_net *ks, struct device *dev) 1073{ 1074 struct mii_bus *mii_bus; 1075 int ret; 1076 1077 mii_bus = mdiobus_alloc(); 1078 if (!mii_bus) 1079 return -ENOMEM; 1080 1081 mii_bus->name = "ks8851_eth_mii"; 1082 mii_bus->read = ks8851_mdio_read; 1083 mii_bus->write = ks8851_mdio_write; 1084 mii_bus->priv = ks; 1085 mii_bus->parent = dev; 1086 mii_bus->phy_mask = ~((u32)BIT(0)); 1087 snprintf(mii_bus->id, MII_BUS_ID_SIZE, "%s", dev_name(dev)); 1088 1089 ret = mdiobus_register(mii_bus); 1090 if (ret) 1091 goto err_mdiobus_register; 1092 1093 ks->mii_bus = mii_bus; 1094 1095 return 0; 1096 1097err_mdiobus_register: 1098 mdiobus_free(mii_bus); 1099 return ret; 1100} 1101 1102static void ks8851_unregister_mdiobus(struct ks8851_net *ks) 1103{ 1104 mdiobus_unregister(ks->mii_bus); 1105 mdiobus_free(ks->mii_bus); 1106} 1107 1108int ks8851_probe_common(struct net_device *netdev, struct device *dev, 1109 int msg_en) 1110{ 1111 struct ks8851_net *ks = netdev_priv(netdev); 1112 unsigned cider; 1113 int ret; 1114 1115 ks->netdev = netdev; 1116 ks->tx_space = 6144; 1117 1118 ks->gpio = devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_HIGH); 1119 ret = PTR_ERR_OR_ZERO(ks->gpio); 1120 if (ret) { 1121 if (ret != -EPROBE_DEFER) 1122 dev_err(dev, "reset gpio request failed: %d\n", ret); 1123 return ret; 1124 } 1125 1126 ret = gpiod_set_consumer_name(ks->gpio, "ks8851_rst_n"); 1127 if (ret) { 1128 dev_err(dev, "failed to set reset gpio name: %d\n", ret); 1129 return ret; 1130 } 1131 1132 ks->vdd_io = devm_regulator_get(dev, "vdd-io"); 1133 if (IS_ERR(ks->vdd_io)) { 1134 ret = PTR_ERR(ks->vdd_io); 1135 goto err_reg_io; 1136 } 1137 1138 ret = regulator_enable(ks->vdd_io); 1139 if (ret) { 1140 dev_err(dev, "regulator vdd_io enable fail: %d\n", ret); 1141 goto err_reg_io; 1142 } 1143 1144 ks->vdd_reg = devm_regulator_get(dev, "vdd"); 1145 if (IS_ERR(ks->vdd_reg)) { 1146 ret = PTR_ERR(ks->vdd_reg); 1147 goto err_reg; 1148 } 1149 1150 ret = regulator_enable(ks->vdd_reg); 1151 if (ret) { 1152 dev_err(dev, "regulator vdd enable fail: %d\n", ret); 1153 goto err_reg; 1154 } 1155 1156 if (ks->gpio) { 1157 usleep_range(10000, 11000); 1158 gpiod_set_value_cansleep(ks->gpio, 0); 1159 } 1160 1161 spin_lock_init(&ks->statelock); 1162 1163 INIT_WORK(&ks->rxctrl_work, ks8851_rxctrl_work); 1164 1165 SET_NETDEV_DEV(netdev, dev); 1166 1167 /* setup EEPROM state */ 1168 ks->eeprom.data = ks; 1169 ks->eeprom.width = PCI_EEPROM_WIDTH_93C46; 1170 ks->eeprom.register_read = ks8851_eeprom_regread; 1171 ks->eeprom.register_write = ks8851_eeprom_regwrite; 1172 1173 /* setup mii state */ 1174 ks->mii.dev = netdev; 1175 ks->mii.phy_id = 1; 1176 ks->mii.phy_id_mask = 1; 1177 ks->mii.reg_num_mask = 0xf; 1178 ks->mii.mdio_read = ks8851_phy_read; 1179 ks->mii.mdio_write = ks8851_phy_write; 1180 1181 dev_info(dev, "message enable is %d\n", msg_en); 1182 1183 ret = ks8851_register_mdiobus(ks, dev); 1184 if (ret) 1185 goto err_mdio; 1186 1187 /* set the default message enable */ 1188 ks->msg_enable = netif_msg_init(msg_en, NETIF_MSG_DRV | 1189 NETIF_MSG_PROBE | 1190 NETIF_MSG_LINK); 1191 1192 skb_queue_head_init(&ks->txq); 1193 1194 netdev->ethtool_ops = &ks8851_ethtool_ops; 1195 1196 dev_set_drvdata(dev, ks); 1197 1198 netif_carrier_off(ks->netdev); 1199 netdev->if_port = IF_PORT_100BASET; 1200 netdev->netdev_ops = &ks8851_netdev_ops; 1201 1202 /* issue a global soft reset to reset the device. */ 1203 ks8851_soft_reset(ks, GRR_GSR); 1204 1205 /* simple check for a valid chip being connected to the bus */ 1206 cider = ks8851_rdreg16(ks, KS_CIDER); 1207 if ((cider & ~CIDER_REV_MASK) != CIDER_ID) { 1208 dev_err(dev, "failed to read device ID\n"); 1209 ret = -ENODEV; 1210 goto err_id; 1211 } 1212 1213 /* cache the contents of the CCR register for EEPROM, etc. */ 1214 ks->rc_ccr = ks8851_rdreg16(ks, KS_CCR); 1215 1216 ks8851_read_selftest(ks); 1217 ks8851_init_mac(ks, dev->of_node); 1218 1219 ret = register_netdev(netdev); 1220 if (ret) { 1221 dev_err(dev, "failed to register network device\n"); 1222 goto err_id; 1223 } 1224 1225 netdev_info(netdev, "revision %d, MAC %pM, IRQ %d, %s EEPROM\n", 1226 CIDER_REV_GET(cider), netdev->dev_addr, netdev->irq, 1227 ks->rc_ccr & CCR_EEPROM ? "has" : "no"); 1228 1229 return 0; 1230 1231err_id: 1232 ks8851_unregister_mdiobus(ks); 1233err_mdio: 1234 if (ks->gpio) 1235 gpiod_set_value_cansleep(ks->gpio, 1); 1236 regulator_disable(ks->vdd_reg); 1237err_reg: 1238 regulator_disable(ks->vdd_io); 1239err_reg_io: 1240 return ret; 1241} 1242EXPORT_SYMBOL_GPL(ks8851_probe_common); 1243 1244void ks8851_remove_common(struct device *dev) 1245{ 1246 struct ks8851_net *priv = dev_get_drvdata(dev); 1247 1248 ks8851_unregister_mdiobus(priv); 1249 1250 if (netif_msg_drv(priv)) 1251 dev_info(dev, "remove\n"); 1252 1253 unregister_netdev(priv->netdev); 1254 if (priv->gpio) 1255 gpiod_set_value_cansleep(priv->gpio, 1); 1256 regulator_disable(priv->vdd_reg); 1257 regulator_disable(priv->vdd_io); 1258} 1259EXPORT_SYMBOL_GPL(ks8851_remove_common); 1260 1261MODULE_DESCRIPTION("KS8851 Network driver"); 1262MODULE_AUTHOR("Ben Dooks <ben@simtec.co.uk>"); 1263MODULE_LICENSE("GPL"); 1264