1// SPDX-License-Identifier: GPL-2.0 2/* 3 * Omnivision OV2680 CMOS Image Sensor driver 4 * 5 * Copyright (C) 2018 Linaro Ltd 6 * 7 * Based on OV5640 Sensor Driver 8 * Copyright (C) 2011-2013 Freescale Semiconductor, Inc. All Rights Reserved. 9 * Copyright (C) 2014-2017 Mentor Graphics Inc. 10 * 11 */ 12 13#include <linux/clk.h> 14#include <linux/delay.h> 15#include <linux/err.h> 16#include <linux/gpio/consumer.h> 17#include <linux/i2c.h> 18#include <linux/init.h> 19#include <linux/mod_devicetable.h> 20#include <linux/module.h> 21#include <linux/pm_runtime.h> 22#include <linux/regmap.h> 23#include <linux/regulator/consumer.h> 24 25#include <media/v4l2-cci.h> 26#include <media/v4l2-common.h> 27#include <media/v4l2-ctrls.h> 28#include <media/v4l2-fwnode.h> 29#include <media/v4l2-subdev.h> 30 31#define OV2680_CHIP_ID 0x2680 32 33#define OV2680_REG_STREAM_CTRL CCI_REG8(0x0100) 34#define OV2680_REG_SOFT_RESET CCI_REG8(0x0103) 35 36#define OV2680_REG_CHIP_ID CCI_REG16(0x300a) 37#define OV2680_REG_SC_CMMN_SUB_ID CCI_REG8(0x302a) 38#define OV2680_REG_PLL_MULTIPLIER CCI_REG16(0x3081) 39 40#define OV2680_REG_EXPOSURE_PK CCI_REG24(0x3500) 41#define OV2680_REG_R_MANUAL CCI_REG8(0x3503) 42#define OV2680_REG_GAIN_PK CCI_REG16(0x350a) 43 44#define OV2680_REG_SENSOR_CTRL_0A CCI_REG8(0x370a) 45 46#define OV2680_REG_HORIZONTAL_START CCI_REG16(0x3800) 47#define OV2680_REG_VERTICAL_START CCI_REG16(0x3802) 48#define OV2680_REG_HORIZONTAL_END CCI_REG16(0x3804) 49#define OV2680_REG_VERTICAL_END CCI_REG16(0x3806) 50#define OV2680_REG_HORIZONTAL_OUTPUT_SIZE CCI_REG16(0x3808) 51#define OV2680_REG_VERTICAL_OUTPUT_SIZE CCI_REG16(0x380a) 52#define OV2680_REG_TIMING_HTS CCI_REG16(0x380c) 53#define OV2680_REG_TIMING_VTS CCI_REG16(0x380e) 54#define OV2680_REG_ISP_X_WIN CCI_REG16(0x3810) 55#define OV2680_REG_ISP_Y_WIN CCI_REG16(0x3812) 56#define OV2680_REG_X_INC CCI_REG8(0x3814) 57#define OV2680_REG_Y_INC CCI_REG8(0x3815) 58#define OV2680_REG_FORMAT1 CCI_REG8(0x3820) 59#define OV2680_REG_FORMAT2 CCI_REG8(0x3821) 60 61#define OV2680_REG_ISP_CTRL00 CCI_REG8(0x5080) 62 63#define OV2680_REG_X_WIN CCI_REG16(0x5704) 64#define OV2680_REG_Y_WIN CCI_REG16(0x5706) 65 66#define OV2680_FRAME_RATE 30 67 68#define OV2680_NATIVE_WIDTH 1616 69#define OV2680_NATIVE_HEIGHT 1216 70#define OV2680_NATIVE_START_LEFT 0 71#define OV2680_NATIVE_START_TOP 0 72#define OV2680_ACTIVE_WIDTH 1600 73#define OV2680_ACTIVE_HEIGHT 1200 74#define OV2680_ACTIVE_START_LEFT 8 75#define OV2680_ACTIVE_START_TOP 8 76#define OV2680_MIN_CROP_WIDTH 2 77#define OV2680_MIN_CROP_HEIGHT 2 78 79/* Fixed pre-div of 1/2 */ 80#define OV2680_PLL_PREDIV0 2 81 82/* Pre-div configurable through reg 0x3080, left at its default of 0x02 : 1/2 */ 83#define OV2680_PLL_PREDIV 2 84 85/* 66MHz pixel clock: 66MHz / 1704 * 1294 = 30fps */ 86#define OV2680_PIXELS_PER_LINE 1704 87#define OV2680_LINES_PER_FRAME 1294 88 89/* If possible send 16 extra rows / lines to the ISP as padding */ 90#define OV2680_END_MARGIN 16 91 92/* Max exposure time is VTS - 8 */ 93#define OV2680_INTEGRATION_TIME_MARGIN 8 94 95#define OV2680_DEFAULT_WIDTH 800 96#define OV2680_DEFAULT_HEIGHT 600 97 98/* For enum_frame_size() full-size + binned-/quarter-size */ 99#define OV2680_FRAME_SIZES 2 100 101static const char * const ov2680_supply_name[] = { 102 "DOVDD", 103 "DVDD", 104 "AVDD", 105}; 106 107#define OV2680_NUM_SUPPLIES ARRAY_SIZE(ov2680_supply_name) 108 109enum { 110 OV2680_19_2_MHZ, 111 OV2680_24_MHZ, 112}; 113 114static const unsigned long ov2680_xvclk_freqs[] = { 115 [OV2680_19_2_MHZ] = 19200000, 116 [OV2680_24_MHZ] = 24000000, 117}; 118 119static const u8 ov2680_pll_multipliers[] = { 120 [OV2680_19_2_MHZ] = 69, 121 [OV2680_24_MHZ] = 55, 122}; 123 124struct ov2680_ctrls { 125 struct v4l2_ctrl_handler handler; 126 struct v4l2_ctrl *exposure; 127 struct v4l2_ctrl *gain; 128 struct v4l2_ctrl *hflip; 129 struct v4l2_ctrl *vflip; 130 struct v4l2_ctrl *test_pattern; 131 struct v4l2_ctrl *link_freq; 132 struct v4l2_ctrl *pixel_rate; 133}; 134 135struct ov2680_mode { 136 struct v4l2_rect crop; 137 struct v4l2_mbus_framefmt fmt; 138 struct v4l2_fract frame_interval; 139 bool binning; 140 u16 h_start; 141 u16 v_start; 142 u16 h_end; 143 u16 v_end; 144 u16 h_output_size; 145 u16 v_output_size; 146 u16 hts; 147 u16 vts; 148}; 149 150struct ov2680_dev { 151 struct device *dev; 152 struct regmap *regmap; 153 struct v4l2_subdev sd; 154 155 struct media_pad pad; 156 struct clk *xvclk; 157 u32 xvclk_freq; 158 u8 pll_mult; 159 s64 link_freq[1]; 160 u64 pixel_rate; 161 struct regulator_bulk_data supplies[OV2680_NUM_SUPPLIES]; 162 163 struct gpio_desc *pwdn_gpio; 164 struct mutex lock; /* protect members */ 165 166 bool is_streaming; 167 168 struct ov2680_ctrls ctrls; 169 struct ov2680_mode mode; 170}; 171 172static const struct v4l2_rect ov2680_default_crop = { 173 .left = OV2680_ACTIVE_START_LEFT, 174 .top = OV2680_ACTIVE_START_TOP, 175 .width = OV2680_ACTIVE_WIDTH, 176 .height = OV2680_ACTIVE_HEIGHT, 177}; 178 179static const char * const test_pattern_menu[] = { 180 "Disabled", 181 "Color Bars", 182 "Random Data", 183 "Square", 184 "Black Image", 185}; 186 187static const int ov2680_hv_flip_bayer_order[] = { 188 MEDIA_BUS_FMT_SBGGR10_1X10, 189 MEDIA_BUS_FMT_SGRBG10_1X10, 190 MEDIA_BUS_FMT_SGBRG10_1X10, 191 MEDIA_BUS_FMT_SRGGB10_1X10, 192}; 193 194static const struct reg_sequence ov2680_global_setting[] = { 195 /* MIPI PHY, 0x10 -> 0x1c enable bp_c_hs_en_lat and bp_d_hs_en_lat */ 196 {0x3016, 0x1c}, 197 198 /* R MANUAL set exposure and gain to manual (hw does not do auto) */ 199 {0x3503, 0x03}, 200 201 /* Analog control register tweaks */ 202 {0x3603, 0x39}, /* Reset value 0x99 */ 203 {0x3604, 0x24}, /* Reset value 0x74 */ 204 {0x3621, 0x37}, /* Reset value 0x44 */ 205 206 /* Sensor control register tweaks */ 207 {0x3701, 0x64}, /* Reset value 0x61 */ 208 {0x3705, 0x3c}, /* Reset value 0x21 */ 209 {0x370c, 0x50}, /* Reset value 0x10 */ 210 {0x370d, 0xc0}, /* Reset value 0x00 */ 211 {0x3718, 0x88}, /* Reset value 0x80 */ 212 213 /* PSRAM tweaks */ 214 {0x3781, 0x80}, /* Reset value 0x00 */ 215 {0x3784, 0x0c}, /* Reset value 0x00, based on OV2680_R1A_AM10.ovt */ 216 {0x3789, 0x60}, /* Reset value 0x50 */ 217 218 /* BLC CTRL00 0x01 -> 0x81 set avg_weight to 8 */ 219 {0x4000, 0x81}, 220 221 /* Set black level compensation range to 0 - 3 (default 0 - 11) */ 222 {0x4008, 0x00}, 223 {0x4009, 0x03}, 224 225 /* VFIFO R2 0x00 -> 0x02 set Frame reset enable */ 226 {0x4602, 0x02}, 227 228 /* MIPI ctrl CLK PREPARE MIN change from 0x26 (38) -> 0x36 (54) */ 229 {0x481f, 0x36}, 230 231 /* MIPI ctrl CLK LPX P MIN change from 0x32 (50) -> 0x36 (54) */ 232 {0x4825, 0x36}, 233 234 /* R ISP CTRL2 0x20 -> 0x30, set sof_sel bit */ 235 {0x5002, 0x30}, 236 237 /* 238 * Window CONTROL 0x00 -> 0x01, enable manual window control, 239 * this is necessary for full size flip and mirror support. 240 */ 241 {0x5708, 0x01}, 242 243 /* 244 * DPC CTRL0 0x14 -> 0x3e, set enable_tail, enable_3x3_cluster 245 * and enable_general_tail bits based OV2680_R1A_AM10.ovt. 246 */ 247 {0x5780, 0x3e}, 248 249 /* DPC MORE CONNECTION CASE THRE 0x0c (12) -> 0x02 (2) */ 250 {0x5788, 0x02}, 251 252 /* DPC GAIN LIST1 0x0f (15) -> 0x08 (8) */ 253 {0x578e, 0x08}, 254 255 /* DPC GAIN LIST2 0x3f (63) -> 0x0c (12) */ 256 {0x578f, 0x0c}, 257 258 /* DPC THRE RATIO 0x04 (4) -> 0x00 (0) */ 259 {0x5792, 0x00}, 260}; 261 262static struct ov2680_dev *to_ov2680_dev(struct v4l2_subdev *sd) 263{ 264 return container_of(sd, struct ov2680_dev, sd); 265} 266 267static inline struct v4l2_subdev *ctrl_to_sd(struct v4l2_ctrl *ctrl) 268{ 269 return &container_of(ctrl->handler, struct ov2680_dev, 270 ctrls.handler)->sd; 271} 272 273static void ov2680_power_up(struct ov2680_dev *sensor) 274{ 275 if (!sensor->pwdn_gpio) 276 return; 277 278 gpiod_set_value(sensor->pwdn_gpio, 0); 279 usleep_range(5000, 10000); 280} 281 282static void ov2680_power_down(struct ov2680_dev *sensor) 283{ 284 if (!sensor->pwdn_gpio) 285 return; 286 287 gpiod_set_value(sensor->pwdn_gpio, 1); 288 usleep_range(5000, 10000); 289} 290 291static void ov2680_set_bayer_order(struct ov2680_dev *sensor, 292 struct v4l2_mbus_framefmt *fmt) 293{ 294 int hv_flip = 0; 295 296 if (sensor->ctrls.vflip && sensor->ctrls.vflip->val) 297 hv_flip += 1; 298 299 if (sensor->ctrls.hflip && sensor->ctrls.hflip->val) 300 hv_flip += 2; 301 302 fmt->code = ov2680_hv_flip_bayer_order[hv_flip]; 303} 304 305static struct v4l2_mbus_framefmt * 306__ov2680_get_pad_format(struct ov2680_dev *sensor, 307 struct v4l2_subdev_state *state, 308 unsigned int pad, 309 enum v4l2_subdev_format_whence which) 310{ 311 if (which == V4L2_SUBDEV_FORMAT_TRY) 312 return v4l2_subdev_state_get_format(state, pad); 313 314 return &sensor->mode.fmt; 315} 316 317static struct v4l2_rect * 318__ov2680_get_pad_crop(struct ov2680_dev *sensor, 319 struct v4l2_subdev_state *state, 320 unsigned int pad, 321 enum v4l2_subdev_format_whence which) 322{ 323 if (which == V4L2_SUBDEV_FORMAT_TRY) 324 return v4l2_subdev_state_get_crop(state, pad); 325 326 return &sensor->mode.crop; 327} 328 329static void ov2680_fill_format(struct ov2680_dev *sensor, 330 struct v4l2_mbus_framefmt *fmt, 331 unsigned int width, unsigned int height) 332{ 333 memset(fmt, 0, sizeof(*fmt)); 334 fmt->width = width; 335 fmt->height = height; 336 fmt->field = V4L2_FIELD_NONE; 337 fmt->colorspace = V4L2_COLORSPACE_SRGB; 338 ov2680_set_bayer_order(sensor, fmt); 339} 340 341static void ov2680_calc_mode(struct ov2680_dev *sensor) 342{ 343 int width = sensor->mode.fmt.width; 344 int height = sensor->mode.fmt.height; 345 int orig_width = width; 346 int orig_height = height; 347 348 if (width <= (sensor->mode.crop.width / 2) && 349 height <= (sensor->mode.crop.height / 2)) { 350 sensor->mode.binning = true; 351 width *= 2; 352 height *= 2; 353 } else { 354 sensor->mode.binning = false; 355 } 356 357 sensor->mode.h_start = (sensor->mode.crop.left + 358 (sensor->mode.crop.width - width) / 2) & ~1; 359 sensor->mode.v_start = (sensor->mode.crop.top + 360 (sensor->mode.crop.height - height) / 2) & ~1; 361 sensor->mode.h_end = 362 min(sensor->mode.h_start + width + OV2680_END_MARGIN - 1, 363 OV2680_NATIVE_WIDTH - 1); 364 sensor->mode.v_end = 365 min(sensor->mode.v_start + height + OV2680_END_MARGIN - 1, 366 OV2680_NATIVE_HEIGHT - 1); 367 sensor->mode.h_output_size = orig_width; 368 sensor->mode.v_output_size = orig_height; 369 sensor->mode.hts = OV2680_PIXELS_PER_LINE; 370 sensor->mode.vts = OV2680_LINES_PER_FRAME; 371} 372 373static int ov2680_set_mode(struct ov2680_dev *sensor) 374{ 375 u8 sensor_ctrl_0a, inc, fmt1, fmt2; 376 int ret = 0; 377 378 if (sensor->mode.binning) { 379 sensor_ctrl_0a = 0x23; 380 inc = 0x31; 381 fmt1 = 0xc2; 382 fmt2 = 0x01; 383 } else { 384 sensor_ctrl_0a = 0x21; 385 inc = 0x11; 386 fmt1 = 0xc0; 387 fmt2 = 0x00; 388 } 389 390 cci_write(sensor->regmap, OV2680_REG_SENSOR_CTRL_0A, 391 sensor_ctrl_0a, &ret); 392 cci_write(sensor->regmap, OV2680_REG_HORIZONTAL_START, 393 sensor->mode.h_start, &ret); 394 cci_write(sensor->regmap, OV2680_REG_VERTICAL_START, 395 sensor->mode.v_start, &ret); 396 cci_write(sensor->regmap, OV2680_REG_HORIZONTAL_END, 397 sensor->mode.h_end, &ret); 398 cci_write(sensor->regmap, OV2680_REG_VERTICAL_END, 399 sensor->mode.v_end, &ret); 400 cci_write(sensor->regmap, OV2680_REG_HORIZONTAL_OUTPUT_SIZE, 401 sensor->mode.h_output_size, &ret); 402 cci_write(sensor->regmap, OV2680_REG_VERTICAL_OUTPUT_SIZE, 403 sensor->mode.v_output_size, &ret); 404 cci_write(sensor->regmap, OV2680_REG_TIMING_HTS, 405 sensor->mode.hts, &ret); 406 cci_write(sensor->regmap, OV2680_REG_TIMING_VTS, 407 sensor->mode.vts, &ret); 408 cci_write(sensor->regmap, OV2680_REG_ISP_X_WIN, 0, &ret); 409 cci_write(sensor->regmap, OV2680_REG_ISP_Y_WIN, 0, &ret); 410 cci_write(sensor->regmap, OV2680_REG_X_INC, inc, &ret); 411 cci_write(sensor->regmap, OV2680_REG_Y_INC, inc, &ret); 412 cci_write(sensor->regmap, OV2680_REG_X_WIN, 413 sensor->mode.h_output_size, &ret); 414 cci_write(sensor->regmap, OV2680_REG_Y_WIN, 415 sensor->mode.v_output_size, &ret); 416 cci_write(sensor->regmap, OV2680_REG_FORMAT1, fmt1, &ret); 417 cci_write(sensor->regmap, OV2680_REG_FORMAT2, fmt2, &ret); 418 419 return ret; 420} 421 422static int ov2680_set_vflip(struct ov2680_dev *sensor, s32 val) 423{ 424 int ret; 425 426 if (sensor->is_streaming) 427 return -EBUSY; 428 429 ret = cci_update_bits(sensor->regmap, OV2680_REG_FORMAT1, 430 BIT(2), val ? BIT(2) : 0, NULL); 431 if (ret < 0) 432 return ret; 433 434 ov2680_set_bayer_order(sensor, &sensor->mode.fmt); 435 return 0; 436} 437 438static int ov2680_set_hflip(struct ov2680_dev *sensor, s32 val) 439{ 440 int ret; 441 442 if (sensor->is_streaming) 443 return -EBUSY; 444 445 ret = cci_update_bits(sensor->regmap, OV2680_REG_FORMAT2, 446 BIT(2), val ? BIT(2) : 0, NULL); 447 if (ret < 0) 448 return ret; 449 450 ov2680_set_bayer_order(sensor, &sensor->mode.fmt); 451 return 0; 452} 453 454static int ov2680_test_pattern_set(struct ov2680_dev *sensor, int value) 455{ 456 int ret = 0; 457 458 if (!value) 459 return cci_update_bits(sensor->regmap, OV2680_REG_ISP_CTRL00, 460 BIT(7), 0, NULL); 461 462 cci_update_bits(sensor->regmap, OV2680_REG_ISP_CTRL00, 463 0x03, value - 1, &ret); 464 cci_update_bits(sensor->regmap, OV2680_REG_ISP_CTRL00, 465 BIT(7), BIT(7), &ret); 466 467 return ret; 468} 469 470static int ov2680_gain_set(struct ov2680_dev *sensor, u32 gain) 471{ 472 return cci_write(sensor->regmap, OV2680_REG_GAIN_PK, gain, NULL); 473} 474 475static int ov2680_exposure_set(struct ov2680_dev *sensor, u32 exp) 476{ 477 return cci_write(sensor->regmap, OV2680_REG_EXPOSURE_PK, exp << 4, 478 NULL); 479} 480 481static int ov2680_stream_enable(struct ov2680_dev *sensor) 482{ 483 int ret; 484 485 ret = cci_write(sensor->regmap, OV2680_REG_PLL_MULTIPLIER, 486 sensor->pll_mult, NULL); 487 if (ret < 0) 488 return ret; 489 490 ret = regmap_multi_reg_write(sensor->regmap, 491 ov2680_global_setting, 492 ARRAY_SIZE(ov2680_global_setting)); 493 if (ret < 0) 494 return ret; 495 496 ret = ov2680_set_mode(sensor); 497 if (ret < 0) 498 return ret; 499 500 /* Restore value of all ctrls */ 501 ret = __v4l2_ctrl_handler_setup(&sensor->ctrls.handler); 502 if (ret < 0) 503 return ret; 504 505 return cci_write(sensor->regmap, OV2680_REG_STREAM_CTRL, 1, NULL); 506} 507 508static int ov2680_stream_disable(struct ov2680_dev *sensor) 509{ 510 return cci_write(sensor->regmap, OV2680_REG_STREAM_CTRL, 0, NULL); 511} 512 513static int ov2680_power_off(struct ov2680_dev *sensor) 514{ 515 clk_disable_unprepare(sensor->xvclk); 516 ov2680_power_down(sensor); 517 regulator_bulk_disable(OV2680_NUM_SUPPLIES, sensor->supplies); 518 return 0; 519} 520 521static int ov2680_power_on(struct ov2680_dev *sensor) 522{ 523 int ret; 524 525 ret = regulator_bulk_enable(OV2680_NUM_SUPPLIES, sensor->supplies); 526 if (ret < 0) { 527 dev_err(sensor->dev, "failed to enable regulators: %d\n", ret); 528 return ret; 529 } 530 531 if (!sensor->pwdn_gpio) { 532 ret = cci_write(sensor->regmap, OV2680_REG_SOFT_RESET, 0x01, 533 NULL); 534 if (ret != 0) { 535 dev_err(sensor->dev, "sensor soft reset failed\n"); 536 goto err_disable_regulators; 537 } 538 usleep_range(1000, 2000); 539 } else { 540 ov2680_power_down(sensor); 541 ov2680_power_up(sensor); 542 } 543 544 ret = clk_prepare_enable(sensor->xvclk); 545 if (ret < 0) 546 goto err_disable_regulators; 547 548 return 0; 549 550err_disable_regulators: 551 regulator_bulk_disable(OV2680_NUM_SUPPLIES, sensor->supplies); 552 return ret; 553} 554 555static int ov2680_get_frame_interval(struct v4l2_subdev *sd, 556 struct v4l2_subdev_state *sd_state, 557 struct v4l2_subdev_frame_interval *fi) 558{ 559 struct ov2680_dev *sensor = to_ov2680_dev(sd); 560 561 /* 562 * FIXME: Implement support for V4L2_SUBDEV_FORMAT_TRY, using the V4L2 563 * subdev active state API. 564 */ 565 if (fi->which != V4L2_SUBDEV_FORMAT_ACTIVE) 566 return -EINVAL; 567 568 mutex_lock(&sensor->lock); 569 fi->interval = sensor->mode.frame_interval; 570 mutex_unlock(&sensor->lock); 571 572 return 0; 573} 574 575static int ov2680_s_stream(struct v4l2_subdev *sd, int enable) 576{ 577 struct ov2680_dev *sensor = to_ov2680_dev(sd); 578 int ret = 0; 579 580 mutex_lock(&sensor->lock); 581 582 if (sensor->is_streaming == !!enable) 583 goto unlock; 584 585 if (enable) { 586 ret = pm_runtime_resume_and_get(sensor->sd.dev); 587 if (ret < 0) 588 goto unlock; 589 590 ret = ov2680_stream_enable(sensor); 591 if (ret < 0) { 592 pm_runtime_put(sensor->sd.dev); 593 goto unlock; 594 } 595 } else { 596 ret = ov2680_stream_disable(sensor); 597 pm_runtime_put(sensor->sd.dev); 598 } 599 600 sensor->is_streaming = !!enable; 601 602unlock: 603 mutex_unlock(&sensor->lock); 604 605 return ret; 606} 607 608static int ov2680_enum_mbus_code(struct v4l2_subdev *sd, 609 struct v4l2_subdev_state *sd_state, 610 struct v4l2_subdev_mbus_code_enum *code) 611{ 612 struct ov2680_dev *sensor = to_ov2680_dev(sd); 613 614 if (code->index != 0) 615 return -EINVAL; 616 617 code->code = sensor->mode.fmt.code; 618 619 return 0; 620} 621 622static int ov2680_get_fmt(struct v4l2_subdev *sd, 623 struct v4l2_subdev_state *sd_state, 624 struct v4l2_subdev_format *format) 625{ 626 struct ov2680_dev *sensor = to_ov2680_dev(sd); 627 struct v4l2_mbus_framefmt *fmt; 628 629 fmt = __ov2680_get_pad_format(sensor, sd_state, format->pad, 630 format->which); 631 632 mutex_lock(&sensor->lock); 633 format->format = *fmt; 634 mutex_unlock(&sensor->lock); 635 636 return 0; 637} 638 639static int ov2680_set_fmt(struct v4l2_subdev *sd, 640 struct v4l2_subdev_state *sd_state, 641 struct v4l2_subdev_format *format) 642{ 643 struct ov2680_dev *sensor = to_ov2680_dev(sd); 644 struct v4l2_mbus_framefmt *try_fmt; 645 const struct v4l2_rect *crop; 646 unsigned int width, height; 647 int ret = 0; 648 649 crop = __ov2680_get_pad_crop(sensor, sd_state, format->pad, 650 format->which); 651 652 /* Limit set_fmt max size to crop width / height */ 653 width = clamp_val(ALIGN(format->format.width, 2), 654 OV2680_MIN_CROP_WIDTH, crop->width); 655 height = clamp_val(ALIGN(format->format.height, 2), 656 OV2680_MIN_CROP_HEIGHT, crop->height); 657 658 ov2680_fill_format(sensor, &format->format, width, height); 659 660 if (format->which == V4L2_SUBDEV_FORMAT_TRY) { 661 try_fmt = v4l2_subdev_state_get_format(sd_state, 0); 662 *try_fmt = format->format; 663 return 0; 664 } 665 666 mutex_lock(&sensor->lock); 667 668 if (sensor->is_streaming) { 669 ret = -EBUSY; 670 goto unlock; 671 } 672 673 sensor->mode.fmt = format->format; 674 ov2680_calc_mode(sensor); 675 676unlock: 677 mutex_unlock(&sensor->lock); 678 679 return ret; 680} 681 682static int ov2680_get_selection(struct v4l2_subdev *sd, 683 struct v4l2_subdev_state *state, 684 struct v4l2_subdev_selection *sel) 685{ 686 struct ov2680_dev *sensor = to_ov2680_dev(sd); 687 688 switch (sel->target) { 689 case V4L2_SEL_TGT_CROP: 690 mutex_lock(&sensor->lock); 691 sel->r = *__ov2680_get_pad_crop(sensor, state, sel->pad, 692 sel->which); 693 mutex_unlock(&sensor->lock); 694 break; 695 case V4L2_SEL_TGT_NATIVE_SIZE: 696 case V4L2_SEL_TGT_CROP_BOUNDS: 697 sel->r.top = 0; 698 sel->r.left = 0; 699 sel->r.width = OV2680_NATIVE_WIDTH; 700 sel->r.height = OV2680_NATIVE_HEIGHT; 701 break; 702 case V4L2_SEL_TGT_CROP_DEFAULT: 703 sel->r = ov2680_default_crop; 704 break; 705 default: 706 return -EINVAL; 707 } 708 709 return 0; 710} 711 712static int ov2680_set_selection(struct v4l2_subdev *sd, 713 struct v4l2_subdev_state *state, 714 struct v4l2_subdev_selection *sel) 715{ 716 struct ov2680_dev *sensor = to_ov2680_dev(sd); 717 struct v4l2_mbus_framefmt *format; 718 struct v4l2_rect *crop; 719 struct v4l2_rect rect; 720 721 if (sel->target != V4L2_SEL_TGT_CROP) 722 return -EINVAL; 723 724 /* 725 * Clamp the boundaries of the crop rectangle to the size of the sensor 726 * pixel array. Align to multiples of 2 to ensure Bayer pattern isn't 727 * disrupted. 728 */ 729 rect.left = clamp_val(ALIGN(sel->r.left, 2), 730 OV2680_NATIVE_START_LEFT, OV2680_NATIVE_WIDTH); 731 rect.top = clamp_val(ALIGN(sel->r.top, 2), 732 OV2680_NATIVE_START_TOP, OV2680_NATIVE_HEIGHT); 733 rect.width = clamp_val(ALIGN(sel->r.width, 2), 734 OV2680_MIN_CROP_WIDTH, OV2680_NATIVE_WIDTH); 735 rect.height = clamp_val(ALIGN(sel->r.height, 2), 736 OV2680_MIN_CROP_HEIGHT, OV2680_NATIVE_HEIGHT); 737 738 /* Make sure the crop rectangle isn't outside the bounds of the array */ 739 rect.width = min_t(unsigned int, rect.width, 740 OV2680_NATIVE_WIDTH - rect.left); 741 rect.height = min_t(unsigned int, rect.height, 742 OV2680_NATIVE_HEIGHT - rect.top); 743 744 crop = __ov2680_get_pad_crop(sensor, state, sel->pad, sel->which); 745 746 mutex_lock(&sensor->lock); 747 if (rect.width != crop->width || rect.height != crop->height) { 748 /* 749 * Reset the output image size if the crop rectangle size has 750 * been modified. 751 */ 752 format = __ov2680_get_pad_format(sensor, state, sel->pad, 753 sel->which); 754 format->width = rect.width; 755 format->height = rect.height; 756 } 757 758 *crop = rect; 759 mutex_unlock(&sensor->lock); 760 761 sel->r = rect; 762 763 return 0; 764} 765 766static int ov2680_init_state(struct v4l2_subdev *sd, 767 struct v4l2_subdev_state *sd_state) 768{ 769 struct ov2680_dev *sensor = to_ov2680_dev(sd); 770 771 *v4l2_subdev_state_get_crop(sd_state, 0) = ov2680_default_crop; 772 773 ov2680_fill_format(sensor, v4l2_subdev_state_get_format(sd_state, 0), 774 OV2680_DEFAULT_WIDTH, OV2680_DEFAULT_HEIGHT); 775 return 0; 776} 777 778static int ov2680_enum_frame_size(struct v4l2_subdev *sd, 779 struct v4l2_subdev_state *sd_state, 780 struct v4l2_subdev_frame_size_enum *fse) 781{ 782 struct ov2680_dev *sensor = to_ov2680_dev(sd); 783 struct v4l2_rect *crop; 784 785 if (fse->index >= OV2680_FRAME_SIZES) 786 return -EINVAL; 787 788 crop = __ov2680_get_pad_crop(sensor, sd_state, fse->pad, fse->which); 789 if (!crop) 790 return -EINVAL; 791 792 fse->min_width = crop->width / (fse->index + 1); 793 fse->min_height = crop->height / (fse->index + 1); 794 fse->max_width = fse->min_width; 795 fse->max_height = fse->min_height; 796 797 return 0; 798} 799 800static bool ov2680_valid_frame_size(struct v4l2_subdev *sd, 801 struct v4l2_subdev_state *sd_state, 802 struct v4l2_subdev_frame_interval_enum *fie) 803{ 804 struct v4l2_subdev_frame_size_enum fse = { 805 .pad = fie->pad, 806 .which = fie->which, 807 }; 808 int i; 809 810 for (i = 0; i < OV2680_FRAME_SIZES; i++) { 811 fse.index = i; 812 813 if (ov2680_enum_frame_size(sd, sd_state, &fse)) 814 return false; 815 816 if (fie->width == fse.min_width && 817 fie->height == fse.min_height) 818 return true; 819 } 820 821 return false; 822} 823 824static int ov2680_enum_frame_interval(struct v4l2_subdev *sd, 825 struct v4l2_subdev_state *sd_state, 826 struct v4l2_subdev_frame_interval_enum *fie) 827{ 828 struct ov2680_dev *sensor = to_ov2680_dev(sd); 829 830 /* Only 1 framerate */ 831 if (fie->index || !ov2680_valid_frame_size(sd, sd_state, fie)) 832 return -EINVAL; 833 834 fie->interval = sensor->mode.frame_interval; 835 836 return 0; 837} 838 839static int ov2680_s_ctrl(struct v4l2_ctrl *ctrl) 840{ 841 struct v4l2_subdev *sd = ctrl_to_sd(ctrl); 842 struct ov2680_dev *sensor = to_ov2680_dev(sd); 843 int ret; 844 845 /* Only apply changes to the controls if the device is powered up */ 846 if (!pm_runtime_get_if_in_use(sensor->sd.dev)) { 847 ov2680_set_bayer_order(sensor, &sensor->mode.fmt); 848 return 0; 849 } 850 851 switch (ctrl->id) { 852 case V4L2_CID_ANALOGUE_GAIN: 853 ret = ov2680_gain_set(sensor, ctrl->val); 854 break; 855 case V4L2_CID_EXPOSURE: 856 ret = ov2680_exposure_set(sensor, ctrl->val); 857 break; 858 case V4L2_CID_VFLIP: 859 ret = ov2680_set_vflip(sensor, ctrl->val); 860 break; 861 case V4L2_CID_HFLIP: 862 ret = ov2680_set_hflip(sensor, ctrl->val); 863 break; 864 case V4L2_CID_TEST_PATTERN: 865 ret = ov2680_test_pattern_set(sensor, ctrl->val); 866 break; 867 default: 868 ret = -EINVAL; 869 break; 870 } 871 872 pm_runtime_put(sensor->sd.dev); 873 return ret; 874} 875 876static const struct v4l2_ctrl_ops ov2680_ctrl_ops = { 877 .s_ctrl = ov2680_s_ctrl, 878}; 879 880static const struct v4l2_subdev_video_ops ov2680_video_ops = { 881 .s_stream = ov2680_s_stream, 882}; 883 884static const struct v4l2_subdev_pad_ops ov2680_pad_ops = { 885 .enum_mbus_code = ov2680_enum_mbus_code, 886 .enum_frame_size = ov2680_enum_frame_size, 887 .enum_frame_interval = ov2680_enum_frame_interval, 888 .get_fmt = ov2680_get_fmt, 889 .set_fmt = ov2680_set_fmt, 890 .get_selection = ov2680_get_selection, 891 .set_selection = ov2680_set_selection, 892 .get_frame_interval = ov2680_get_frame_interval, 893 .set_frame_interval = ov2680_get_frame_interval, 894}; 895 896static const struct v4l2_subdev_ops ov2680_subdev_ops = { 897 .video = &ov2680_video_ops, 898 .pad = &ov2680_pad_ops, 899}; 900 901static const struct v4l2_subdev_internal_ops ov2680_internal_ops = { 902 .init_state = ov2680_init_state, 903}; 904 905static int ov2680_mode_init(struct ov2680_dev *sensor) 906{ 907 /* set initial mode */ 908 sensor->mode.crop = ov2680_default_crop; 909 ov2680_fill_format(sensor, &sensor->mode.fmt, 910 OV2680_DEFAULT_WIDTH, OV2680_DEFAULT_HEIGHT); 911 ov2680_calc_mode(sensor); 912 913 sensor->mode.frame_interval.denominator = OV2680_FRAME_RATE; 914 sensor->mode.frame_interval.numerator = 1; 915 916 return 0; 917} 918 919static int ov2680_v4l2_register(struct ov2680_dev *sensor) 920{ 921 struct i2c_client *client = to_i2c_client(sensor->dev); 922 const struct v4l2_ctrl_ops *ops = &ov2680_ctrl_ops; 923 struct ov2680_ctrls *ctrls = &sensor->ctrls; 924 struct v4l2_ctrl_handler *hdl = &ctrls->handler; 925 int exp_max = OV2680_LINES_PER_FRAME - OV2680_INTEGRATION_TIME_MARGIN; 926 int ret = 0; 927 928 v4l2_i2c_subdev_init(&sensor->sd, client, &ov2680_subdev_ops); 929 sensor->sd.internal_ops = &ov2680_internal_ops; 930 931 sensor->sd.flags = V4L2_SUBDEV_FL_HAS_DEVNODE; 932 sensor->pad.flags = MEDIA_PAD_FL_SOURCE; 933 sensor->sd.entity.function = MEDIA_ENT_F_CAM_SENSOR; 934 935 ret = media_entity_pads_init(&sensor->sd.entity, 1, &sensor->pad); 936 if (ret < 0) 937 return ret; 938 939 v4l2_ctrl_handler_init(hdl, 5); 940 941 hdl->lock = &sensor->lock; 942 943 ctrls->vflip = v4l2_ctrl_new_std(hdl, ops, V4L2_CID_VFLIP, 0, 1, 1, 0); 944 ctrls->hflip = v4l2_ctrl_new_std(hdl, ops, V4L2_CID_HFLIP, 0, 1, 1, 0); 945 946 ctrls->test_pattern = v4l2_ctrl_new_std_menu_items(hdl, 947 &ov2680_ctrl_ops, V4L2_CID_TEST_PATTERN, 948 ARRAY_SIZE(test_pattern_menu) - 1, 949 0, 0, test_pattern_menu); 950 951 ctrls->exposure = v4l2_ctrl_new_std(hdl, ops, V4L2_CID_EXPOSURE, 952 0, exp_max, 1, exp_max); 953 954 ctrls->gain = v4l2_ctrl_new_std(hdl, ops, V4L2_CID_ANALOGUE_GAIN, 955 0, 1023, 1, 250); 956 957 ctrls->link_freq = v4l2_ctrl_new_int_menu(hdl, NULL, V4L2_CID_LINK_FREQ, 958 0, 0, sensor->link_freq); 959 ctrls->pixel_rate = v4l2_ctrl_new_std(hdl, NULL, V4L2_CID_PIXEL_RATE, 960 0, sensor->pixel_rate, 961 1, sensor->pixel_rate); 962 963 if (hdl->error) { 964 ret = hdl->error; 965 goto cleanup_entity; 966 } 967 968 ctrls->vflip->flags |= V4L2_CTRL_FLAG_MODIFY_LAYOUT; 969 ctrls->hflip->flags |= V4L2_CTRL_FLAG_MODIFY_LAYOUT; 970 ctrls->link_freq->flags |= V4L2_CTRL_FLAG_READ_ONLY; 971 972 sensor->sd.ctrl_handler = hdl; 973 974 ret = v4l2_async_register_subdev(&sensor->sd); 975 if (ret < 0) 976 goto cleanup_entity; 977 978 return 0; 979 980cleanup_entity: 981 media_entity_cleanup(&sensor->sd.entity); 982 v4l2_ctrl_handler_free(hdl); 983 984 return ret; 985} 986 987static int ov2680_get_regulators(struct ov2680_dev *sensor) 988{ 989 int i; 990 991 for (i = 0; i < OV2680_NUM_SUPPLIES; i++) 992 sensor->supplies[i].supply = ov2680_supply_name[i]; 993 994 return devm_regulator_bulk_get(sensor->dev, 995 OV2680_NUM_SUPPLIES, sensor->supplies); 996} 997 998static int ov2680_check_id(struct ov2680_dev *sensor) 999{ 1000 u64 chip_id, rev; 1001 int ret = 0; 1002 1003 cci_read(sensor->regmap, OV2680_REG_CHIP_ID, &chip_id, &ret); 1004 cci_read(sensor->regmap, OV2680_REG_SC_CMMN_SUB_ID, &rev, &ret); 1005 if (ret < 0) { 1006 dev_err(sensor->dev, "failed to read chip id\n"); 1007 return ret; 1008 } 1009 1010 if (chip_id != OV2680_CHIP_ID) { 1011 dev_err(sensor->dev, "chip id: 0x%04llx does not match expected 0x%04x\n", 1012 chip_id, OV2680_CHIP_ID); 1013 return -ENODEV; 1014 } 1015 1016 dev_info(sensor->dev, "sensor_revision id = 0x%llx, rev= %lld\n", 1017 chip_id, rev & 0x0f); 1018 1019 return 0; 1020} 1021 1022static int ov2680_parse_dt(struct ov2680_dev *sensor) 1023{ 1024 struct v4l2_fwnode_endpoint bus_cfg = { 1025 .bus_type = V4L2_MBUS_CSI2_DPHY, 1026 }; 1027 struct device *dev = sensor->dev; 1028 struct fwnode_handle *ep_fwnode; 1029 struct gpio_desc *gpio; 1030 unsigned int rate = 0; 1031 int i, ret; 1032 1033 /* 1034 * Sometimes the fwnode graph is initialized by the bridge driver. 1035 * Bridge drivers doing this may also add GPIO mappings, wait for this. 1036 */ 1037 ep_fwnode = fwnode_graph_get_next_endpoint(dev_fwnode(dev), NULL); 1038 if (!ep_fwnode) 1039 return dev_err_probe(dev, -EPROBE_DEFER, 1040 "waiting for fwnode graph endpoint\n"); 1041 1042 ret = v4l2_fwnode_endpoint_alloc_parse(ep_fwnode, &bus_cfg); 1043 fwnode_handle_put(ep_fwnode); 1044 if (ret) 1045 return ret; 1046 1047 /* 1048 * The pin we want is named XSHUTDN in the datasheet. Linux sensor 1049 * drivers have standardized on using "powerdown" as con-id name 1050 * for powerdown or shutdown pins. Older DTB files use "reset", 1051 * so fallback to that if there is no "powerdown" pin. 1052 */ 1053 gpio = devm_gpiod_get_optional(dev, "powerdown", GPIOD_OUT_HIGH); 1054 if (!gpio) 1055 gpio = devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_HIGH); 1056 1057 ret = PTR_ERR_OR_ZERO(gpio); 1058 if (ret < 0) { 1059 dev_dbg(dev, "error while getting reset gpio: %d\n", ret); 1060 goto out_free_bus_cfg; 1061 } 1062 1063 sensor->pwdn_gpio = gpio; 1064 1065 sensor->xvclk = devm_clk_get_optional(dev, "xvclk"); 1066 if (IS_ERR(sensor->xvclk)) { 1067 ret = dev_err_probe(dev, PTR_ERR(sensor->xvclk), 1068 "xvclk clock missing or invalid\n"); 1069 goto out_free_bus_cfg; 1070 } 1071 1072 /* 1073 * We could have either a 24MHz or 19.2MHz clock rate from either DT or 1074 * ACPI... but we also need to support the weird IPU3 case which will 1075 * have an external clock AND a clock-frequency property. Check for the 1076 * clock-frequency property and if found, set that rate if we managed 1077 * to acquire a clock. This should cover the ACPI case. If the system 1078 * uses devicetree then the configured rate should already be set, so 1079 * we can just read it. 1080 */ 1081 ret = fwnode_property_read_u32(dev_fwnode(dev), "clock-frequency", 1082 &rate); 1083 if (ret && !sensor->xvclk) { 1084 dev_err_probe(dev, ret, "invalid clock config\n"); 1085 goto out_free_bus_cfg; 1086 } 1087 1088 if (!ret && sensor->xvclk) { 1089 ret = clk_set_rate(sensor->xvclk, rate); 1090 if (ret) { 1091 dev_err_probe(dev, ret, "failed to set clock rate\n"); 1092 goto out_free_bus_cfg; 1093 } 1094 } 1095 1096 sensor->xvclk_freq = rate ?: clk_get_rate(sensor->xvclk); 1097 1098 for (i = 0; i < ARRAY_SIZE(ov2680_xvclk_freqs); i++) { 1099 if (sensor->xvclk_freq == ov2680_xvclk_freqs[i]) 1100 break; 1101 } 1102 1103 if (i == ARRAY_SIZE(ov2680_xvclk_freqs)) { 1104 ret = dev_err_probe(dev, -EINVAL, 1105 "unsupported xvclk frequency %d Hz\n", 1106 sensor->xvclk_freq); 1107 goto out_free_bus_cfg; 1108 } 1109 1110 sensor->pll_mult = ov2680_pll_multipliers[i]; 1111 1112 sensor->link_freq[0] = sensor->xvclk_freq / OV2680_PLL_PREDIV0 / 1113 OV2680_PLL_PREDIV * sensor->pll_mult; 1114 1115 /* CSI-2 is double data rate, bus-format is 10 bpp */ 1116 sensor->pixel_rate = sensor->link_freq[0] * 2; 1117 do_div(sensor->pixel_rate, 10); 1118 1119 /* Verify bus cfg */ 1120 if (bus_cfg.bus.mipi_csi2.num_data_lanes != 1) { 1121 ret = dev_err_probe(dev, -EINVAL, 1122 "only a 1-lane CSI2 config is supported"); 1123 goto out_free_bus_cfg; 1124 } 1125 1126 for (i = 0; i < bus_cfg.nr_of_link_frequencies; i++) 1127 if (bus_cfg.link_frequencies[i] == sensor->link_freq[0]) 1128 break; 1129 1130 if (bus_cfg.nr_of_link_frequencies == 0 || 1131 bus_cfg.nr_of_link_frequencies == i) { 1132 ret = dev_err_probe(dev, -EINVAL, 1133 "supported link freq %lld not found\n", 1134 sensor->link_freq[0]); 1135 goto out_free_bus_cfg; 1136 } 1137 1138out_free_bus_cfg: 1139 v4l2_fwnode_endpoint_free(&bus_cfg); 1140 return ret; 1141} 1142 1143static int ov2680_probe(struct i2c_client *client) 1144{ 1145 struct device *dev = &client->dev; 1146 struct ov2680_dev *sensor; 1147 int ret; 1148 1149 sensor = devm_kzalloc(dev, sizeof(*sensor), GFP_KERNEL); 1150 if (!sensor) 1151 return -ENOMEM; 1152 1153 sensor->dev = &client->dev; 1154 1155 sensor->regmap = devm_cci_regmap_init_i2c(client, 16); 1156 if (IS_ERR(sensor->regmap)) 1157 return PTR_ERR(sensor->regmap); 1158 1159 ret = ov2680_parse_dt(sensor); 1160 if (ret < 0) 1161 return ret; 1162 1163 ret = ov2680_mode_init(sensor); 1164 if (ret < 0) 1165 return ret; 1166 1167 ret = ov2680_get_regulators(sensor); 1168 if (ret < 0) { 1169 dev_err(dev, "failed to get regulators\n"); 1170 return ret; 1171 } 1172 1173 mutex_init(&sensor->lock); 1174 1175 /* 1176 * Power up and verify the chip now, so that if runtime pm is 1177 * disabled the chip is left on and streaming will work. 1178 */ 1179 ret = ov2680_power_on(sensor); 1180 if (ret < 0) 1181 goto lock_destroy; 1182 1183 ret = ov2680_check_id(sensor); 1184 if (ret < 0) 1185 goto err_powerdown; 1186 1187 pm_runtime_set_active(&client->dev); 1188 pm_runtime_get_noresume(&client->dev); 1189 pm_runtime_enable(&client->dev); 1190 1191 ret = ov2680_v4l2_register(sensor); 1192 if (ret < 0) 1193 goto err_pm_runtime; 1194 1195 pm_runtime_set_autosuspend_delay(&client->dev, 1000); 1196 pm_runtime_use_autosuspend(&client->dev); 1197 pm_runtime_put_autosuspend(&client->dev); 1198 1199 return 0; 1200 1201err_pm_runtime: 1202 pm_runtime_disable(&client->dev); 1203 pm_runtime_put_noidle(&client->dev); 1204err_powerdown: 1205 ov2680_power_off(sensor); 1206lock_destroy: 1207 dev_err(dev, "ov2680 init fail: %d\n", ret); 1208 mutex_destroy(&sensor->lock); 1209 1210 return ret; 1211} 1212 1213static void ov2680_remove(struct i2c_client *client) 1214{ 1215 struct v4l2_subdev *sd = i2c_get_clientdata(client); 1216 struct ov2680_dev *sensor = to_ov2680_dev(sd); 1217 1218 v4l2_async_unregister_subdev(&sensor->sd); 1219 mutex_destroy(&sensor->lock); 1220 media_entity_cleanup(&sensor->sd.entity); 1221 v4l2_ctrl_handler_free(&sensor->ctrls.handler); 1222 1223 /* 1224 * Disable runtime PM. In case runtime PM is disabled in the kernel, 1225 * make sure to turn power off manually. 1226 */ 1227 pm_runtime_disable(&client->dev); 1228 if (!pm_runtime_status_suspended(&client->dev)) 1229 ov2680_power_off(sensor); 1230 pm_runtime_set_suspended(&client->dev); 1231} 1232 1233static int ov2680_suspend(struct device *dev) 1234{ 1235 struct v4l2_subdev *sd = dev_get_drvdata(dev); 1236 struct ov2680_dev *sensor = to_ov2680_dev(sd); 1237 1238 if (sensor->is_streaming) 1239 ov2680_stream_disable(sensor); 1240 1241 return ov2680_power_off(sensor); 1242} 1243 1244static int ov2680_resume(struct device *dev) 1245{ 1246 struct v4l2_subdev *sd = dev_get_drvdata(dev); 1247 struct ov2680_dev *sensor = to_ov2680_dev(sd); 1248 int ret; 1249 1250 ret = ov2680_power_on(sensor); 1251 if (ret < 0) 1252 goto stream_disable; 1253 1254 if (sensor->is_streaming) { 1255 ret = ov2680_stream_enable(sensor); 1256 if (ret < 0) 1257 goto stream_disable; 1258 } 1259 1260 return 0; 1261 1262stream_disable: 1263 ov2680_stream_disable(sensor); 1264 sensor->is_streaming = false; 1265 1266 return ret; 1267} 1268 1269static DEFINE_RUNTIME_DEV_PM_OPS(ov2680_pm_ops, ov2680_suspend, ov2680_resume, 1270 NULL); 1271 1272static const struct of_device_id ov2680_dt_ids[] = { 1273 { .compatible = "ovti,ov2680" }, 1274 { /* sentinel */ }, 1275}; 1276MODULE_DEVICE_TABLE(of, ov2680_dt_ids); 1277 1278static const struct acpi_device_id ov2680_acpi_ids[] = { 1279 { "OVTI2680" }, 1280 { /* sentinel */ } 1281}; 1282MODULE_DEVICE_TABLE(acpi, ov2680_acpi_ids); 1283 1284static struct i2c_driver ov2680_i2c_driver = { 1285 .driver = { 1286 .name = "ov2680", 1287 .pm = pm_sleep_ptr(&ov2680_pm_ops), 1288 .of_match_table = ov2680_dt_ids, 1289 .acpi_match_table = ov2680_acpi_ids, 1290 }, 1291 .probe = ov2680_probe, 1292 .remove = ov2680_remove, 1293}; 1294module_i2c_driver(ov2680_i2c_driver); 1295 1296MODULE_AUTHOR("Rui Miguel Silva <rui.silva@linaro.org>"); 1297MODULE_DESCRIPTION("OV2680 CMOS Image Sensor driver"); 1298MODULE_LICENSE("GPL v2"); 1299