1// SPDX-License-Identifier: GPL-2.0-only 2/* 3 * ov2640 Camera Driver 4 * 5 * Copyright (C) 2010 Alberto Panizzo <maramaopercheseimorto@gmail.com> 6 * 7 * Based on ov772x, ov9640 drivers and previous non merged implementations. 8 * 9 * Copyright 2005-2009 Freescale Semiconductor, Inc. All Rights Reserved. 10 * Copyright (C) 2006, OmniVision 11 */ 12 13#include <linux/init.h> 14#include <linux/module.h> 15#include <linux/i2c.h> 16#include <linux/clk.h> 17#include <linux/slab.h> 18#include <linux/delay.h> 19#include <linux/gpio/consumer.h> 20#include <linux/v4l2-mediabus.h> 21#include <linux/videodev2.h> 22 23#include <media/v4l2-device.h> 24#include <media/v4l2-event.h> 25#include <media/v4l2-subdev.h> 26#include <media/v4l2-ctrls.h> 27#include <media/v4l2-image-sizes.h> 28 29#define VAL_SET(x, mask, rshift, lshift) \ 30 ((((x) >> rshift) & mask) << lshift) 31/* 32 * DSP registers 33 * register offset for BANK_SEL == BANK_SEL_DSP 34 */ 35#define R_BYPASS 0x05 /* Bypass DSP */ 36#define R_BYPASS_DSP_BYPAS 0x01 /* Bypass DSP, sensor out directly */ 37#define R_BYPASS_USE_DSP 0x00 /* Use the internal DSP */ 38#define QS 0x44 /* Quantization Scale Factor */ 39#define CTRLI 0x50 40#define CTRLI_LP_DP 0x80 41#define CTRLI_ROUND 0x40 42#define CTRLI_V_DIV_SET(x) VAL_SET(x, 0x3, 0, 3) 43#define CTRLI_H_DIV_SET(x) VAL_SET(x, 0x3, 0, 0) 44#define HSIZE 0x51 /* H_SIZE[7:0] (real/4) */ 45#define HSIZE_SET(x) VAL_SET(x, 0xFF, 2, 0) 46#define VSIZE 0x52 /* V_SIZE[7:0] (real/4) */ 47#define VSIZE_SET(x) VAL_SET(x, 0xFF, 2, 0) 48#define XOFFL 0x53 /* OFFSET_X[7:0] */ 49#define XOFFL_SET(x) VAL_SET(x, 0xFF, 0, 0) 50#define YOFFL 0x54 /* OFFSET_Y[7:0] */ 51#define YOFFL_SET(x) VAL_SET(x, 0xFF, 0, 0) 52#define VHYX 0x55 /* Offset and size completion */ 53#define VHYX_VSIZE_SET(x) VAL_SET(x, 0x1, (8+2), 7) 54#define VHYX_HSIZE_SET(x) VAL_SET(x, 0x1, (8+2), 3) 55#define VHYX_YOFF_SET(x) VAL_SET(x, 0x3, 8, 4) 56#define VHYX_XOFF_SET(x) VAL_SET(x, 0x3, 8, 0) 57#define DPRP 0x56 58#define TEST 0x57 /* Horizontal size completion */ 59#define TEST_HSIZE_SET(x) VAL_SET(x, 0x1, (9+2), 7) 60#define ZMOW 0x5A /* Zoom: Out Width OUTW[7:0] (real/4) */ 61#define ZMOW_OUTW_SET(x) VAL_SET(x, 0xFF, 2, 0) 62#define ZMOH 0x5B /* Zoom: Out Height OUTH[7:0] (real/4) */ 63#define ZMOH_OUTH_SET(x) VAL_SET(x, 0xFF, 2, 0) 64#define ZMHH 0x5C /* Zoom: Speed and H&W completion */ 65#define ZMHH_ZSPEED_SET(x) VAL_SET(x, 0x0F, 0, 4) 66#define ZMHH_OUTH_SET(x) VAL_SET(x, 0x1, (8+2), 2) 67#define ZMHH_OUTW_SET(x) VAL_SET(x, 0x3, (8+2), 0) 68#define BPADDR 0x7C /* SDE Indirect Register Access: Address */ 69#define BPDATA 0x7D /* SDE Indirect Register Access: Data */ 70#define CTRL2 0x86 /* DSP Module enable 2 */ 71#define CTRL2_DCW_EN 0x20 72#define CTRL2_SDE_EN 0x10 73#define CTRL2_UV_ADJ_EN 0x08 74#define CTRL2_UV_AVG_EN 0x04 75#define CTRL2_CMX_EN 0x01 76#define CTRL3 0x87 /* DSP Module enable 3 */ 77#define CTRL3_BPC_EN 0x80 78#define CTRL3_WPC_EN 0x40 79#define SIZEL 0x8C /* Image Size Completion */ 80#define SIZEL_HSIZE8_11_SET(x) VAL_SET(x, 0x1, 11, 6) 81#define SIZEL_HSIZE8_SET(x) VAL_SET(x, 0x7, 0, 3) 82#define SIZEL_VSIZE8_SET(x) VAL_SET(x, 0x7, 0, 0) 83#define HSIZE8 0xC0 /* Image Horizontal Size HSIZE[10:3] */ 84#define HSIZE8_SET(x) VAL_SET(x, 0xFF, 3, 0) 85#define VSIZE8 0xC1 /* Image Vertical Size VSIZE[10:3] */ 86#define VSIZE8_SET(x) VAL_SET(x, 0xFF, 3, 0) 87#define CTRL0 0xC2 /* DSP Module enable 0 */ 88#define CTRL0_AEC_EN 0x80 89#define CTRL0_AEC_SEL 0x40 90#define CTRL0_STAT_SEL 0x20 91#define CTRL0_VFIRST 0x10 92#define CTRL0_YUV422 0x08 93#define CTRL0_YUV_EN 0x04 94#define CTRL0_RGB_EN 0x02 95#define CTRL0_RAW_EN 0x01 96#define CTRL1 0xC3 /* DSP Module enable 1 */ 97#define CTRL1_CIP 0x80 98#define CTRL1_DMY 0x40 99#define CTRL1_RAW_GMA 0x20 100#define CTRL1_DG 0x10 101#define CTRL1_AWB 0x08 102#define CTRL1_AWB_GAIN 0x04 103#define CTRL1_LENC 0x02 104#define CTRL1_PRE 0x01 105/* REG 0xC7 (unknown name): affects Auto White Balance (AWB) 106 * AWB_OFF 0x40 107 * AWB_SIMPLE 0x10 108 * AWB_ON 0x00 (Advanced AWB ?) */ 109#define R_DVP_SP 0xD3 /* DVP output speed control */ 110#define R_DVP_SP_AUTO_MODE 0x80 111#define R_DVP_SP_DVP_MASK 0x3F /* DVP PCLK = sysclk (48)/[6:0] (YUV0); 112 * = sysclk (48)/(2*[6:0]) (RAW);*/ 113#define IMAGE_MODE 0xDA /* Image Output Format Select */ 114#define IMAGE_MODE_Y8_DVP_EN 0x40 115#define IMAGE_MODE_JPEG_EN 0x10 116#define IMAGE_MODE_YUV422 0x00 117#define IMAGE_MODE_RAW10 0x04 /* (DVP) */ 118#define IMAGE_MODE_RGB565 0x08 119#define IMAGE_MODE_HREF_VSYNC 0x02 /* HREF timing select in DVP JPEG output 120 * mode (0 for HREF is same as sensor) */ 121#define IMAGE_MODE_LBYTE_FIRST 0x01 /* Byte swap enable for DVP 122 * 1: Low byte first UYVY (C2[4] =0) 123 * VYUY (C2[4] =1) 124 * 0: High byte first YUYV (C2[4]=0) 125 * YVYU (C2[4] = 1) */ 126#define RESET 0xE0 /* Reset */ 127#define RESET_MICROC 0x40 128#define RESET_SCCB 0x20 129#define RESET_JPEG 0x10 130#define RESET_DVP 0x04 131#define RESET_IPU 0x02 132#define RESET_CIF 0x01 133#define REGED 0xED /* Register ED */ 134#define REGED_CLK_OUT_DIS 0x10 135#define MS_SP 0xF0 /* SCCB Master Speed */ 136#define SS_ID 0xF7 /* SCCB Slave ID */ 137#define SS_CTRL 0xF8 /* SCCB Slave Control */ 138#define SS_CTRL_ADD_AUTO_INC 0x20 139#define SS_CTRL_EN 0x08 140#define SS_CTRL_DELAY_CLK 0x04 141#define SS_CTRL_ACC_EN 0x02 142#define SS_CTRL_SEN_PASS_THR 0x01 143#define MC_BIST 0xF9 /* Microcontroller misc register */ 144#define MC_BIST_RESET 0x80 /* Microcontroller Reset */ 145#define MC_BIST_BOOT_ROM_SEL 0x40 146#define MC_BIST_12KB_SEL 0x20 147#define MC_BIST_12KB_MASK 0x30 148#define MC_BIST_512KB_SEL 0x08 149#define MC_BIST_512KB_MASK 0x0C 150#define MC_BIST_BUSY_BIT_R 0x02 151#define MC_BIST_MC_RES_ONE_SH_W 0x02 152#define MC_BIST_LAUNCH 0x01 153#define BANK_SEL 0xFF /* Register Bank Select */ 154#define BANK_SEL_DSP 0x00 155#define BANK_SEL_SENS 0x01 156 157/* 158 * Sensor registers 159 * register offset for BANK_SEL == BANK_SEL_SENS 160 */ 161#define GAIN 0x00 /* AGC - Gain control gain setting */ 162#define COM1 0x03 /* Common control 1 */ 163#define COM1_1_DUMMY_FR 0x40 164#define COM1_3_DUMMY_FR 0x80 165#define COM1_7_DUMMY_FR 0xC0 166#define COM1_VWIN_LSB_UXGA 0x0F 167#define COM1_VWIN_LSB_SVGA 0x0A 168#define COM1_VWIN_LSB_CIF 0x06 169#define REG04 0x04 /* Register 04 */ 170#define REG04_DEF 0x20 /* Always set */ 171#define REG04_HFLIP_IMG 0x80 /* Horizontal mirror image ON/OFF */ 172#define REG04_VFLIP_IMG 0x40 /* Vertical flip image ON/OFF */ 173#define REG04_VREF_EN 0x10 174#define REG04_HREF_EN 0x08 175#define REG04_AEC_SET(x) VAL_SET(x, 0x3, 0, 0) 176#define REG08 0x08 /* Frame Exposure One-pin Control Pre-charge Row Num */ 177#define COM2 0x09 /* Common control 2 */ 178#define COM2_SOFT_SLEEP_MODE 0x10 /* Soft sleep mode */ 179 /* Output drive capability */ 180#define COM2_OCAP_Nx_SET(N) (((N) - 1) & 0x03) /* N = [1x .. 4x] */ 181#define PID 0x0A /* Product ID Number MSB */ 182#define VER 0x0B /* Product ID Number LSB */ 183#define COM3 0x0C /* Common control 3 */ 184#define COM3_BAND_50H 0x04 /* 0 For Banding at 60H */ 185#define COM3_BAND_AUTO 0x02 /* Auto Banding */ 186#define COM3_SING_FR_SNAPSH 0x01 /* 0 For enable live video output after the 187 * snapshot sequence*/ 188#define AEC 0x10 /* AEC[9:2] Exposure Value */ 189#define CLKRC 0x11 /* Internal clock */ 190#define CLKRC_EN 0x80 191#define CLKRC_DIV_SET(x) (((x) - 1) & 0x1F) /* CLK = XVCLK/(x) */ 192#define COM7 0x12 /* Common control 7 */ 193#define COM7_SRST 0x80 /* Initiates system reset. All registers are 194 * set to factory default values after which 195 * the chip resumes normal operation */ 196#define COM7_RES_UXGA 0x00 /* Resolution selectors for UXGA */ 197#define COM7_RES_SVGA 0x40 /* SVGA */ 198#define COM7_RES_CIF 0x20 /* CIF */ 199#define COM7_ZOOM_EN 0x04 /* Enable Zoom mode */ 200#define COM7_COLOR_BAR_TEST 0x02 /* Enable Color Bar Test Pattern */ 201#define COM8 0x13 /* Common control 8 */ 202#define COM8_DEF 0xC0 203#define COM8_BNDF_EN 0x20 /* Banding filter ON/OFF */ 204#define COM8_AGC_EN 0x04 /* AGC Auto/Manual control selection */ 205#define COM8_AEC_EN 0x01 /* Auto/Manual Exposure control */ 206#define COM9 0x14 /* Common control 9 207 * Automatic gain ceiling - maximum AGC value [7:5]*/ 208#define COM9_AGC_GAIN_2x 0x00 /* 000 : 2x */ 209#define COM9_AGC_GAIN_4x 0x20 /* 001 : 4x */ 210#define COM9_AGC_GAIN_8x 0x40 /* 010 : 8x */ 211#define COM9_AGC_GAIN_16x 0x60 /* 011 : 16x */ 212#define COM9_AGC_GAIN_32x 0x80 /* 100 : 32x */ 213#define COM9_AGC_GAIN_64x 0xA0 /* 101 : 64x */ 214#define COM9_AGC_GAIN_128x 0xC0 /* 110 : 128x */ 215#define COM10 0x15 /* Common control 10 */ 216#define COM10_PCLK_HREF 0x20 /* PCLK output qualified by HREF */ 217#define COM10_PCLK_RISE 0x10 /* Data is updated at the rising edge of 218 * PCLK (user can latch data at the next 219 * falling edge of PCLK). 220 * 0 otherwise. */ 221#define COM10_HREF_INV 0x08 /* Invert HREF polarity: 222 * HREF negative for valid data*/ 223#define COM10_VSINC_INV 0x02 /* Invert VSYNC polarity */ 224#define HSTART 0x17 /* Horizontal Window start MSB 8 bit */ 225#define HEND 0x18 /* Horizontal Window end MSB 8 bit */ 226#define VSTART 0x19 /* Vertical Window start MSB 8 bit */ 227#define VEND 0x1A /* Vertical Window end MSB 8 bit */ 228#define MIDH 0x1C /* Manufacturer ID byte - high */ 229#define MIDL 0x1D /* Manufacturer ID byte - low */ 230#define AEW 0x24 /* AGC/AEC - Stable operating region (upper limit) */ 231#define AEB 0x25 /* AGC/AEC - Stable operating region (lower limit) */ 232#define VV 0x26 /* AGC/AEC Fast mode operating region */ 233#define VV_HIGH_TH_SET(x) VAL_SET(x, 0xF, 0, 4) 234#define VV_LOW_TH_SET(x) VAL_SET(x, 0xF, 0, 0) 235#define REG2A 0x2A /* Dummy pixel insert MSB */ 236#define FRARL 0x2B /* Dummy pixel insert LSB */ 237#define ADDVFL 0x2D /* LSB of insert dummy lines in Vertical direction */ 238#define ADDVFH 0x2E /* MSB of insert dummy lines in Vertical direction */ 239#define YAVG 0x2F /* Y/G Channel Average value */ 240#define REG32 0x32 /* Common Control 32 */ 241#define REG32_PCLK_DIV_2 0x80 /* PCLK freq divided by 2 */ 242#define REG32_PCLK_DIV_4 0xC0 /* PCLK freq divided by 4 */ 243#define ARCOM2 0x34 /* Zoom: Horizontal start point */ 244#define REG45 0x45 /* Register 45 */ 245#define FLL 0x46 /* Frame Length Adjustment LSBs */ 246#define FLH 0x47 /* Frame Length Adjustment MSBs */ 247#define COM19 0x48 /* Zoom: Vertical start point */ 248#define ZOOMS 0x49 /* Zoom: Vertical start point */ 249#define COM22 0x4B /* Flash light control */ 250#define COM25 0x4E /* For Banding operations */ 251#define COM25_50HZ_BANDING_AEC_MSBS_MASK 0xC0 /* 50Hz Bd. AEC 2 MSBs */ 252#define COM25_60HZ_BANDING_AEC_MSBS_MASK 0x30 /* 60Hz Bd. AEC 2 MSBs */ 253#define COM25_50HZ_BANDING_AEC_MSBS_SET(x) VAL_SET(x, 0x3, 8, 6) 254#define COM25_60HZ_BANDING_AEC_MSBS_SET(x) VAL_SET(x, 0x3, 8, 4) 255#define BD50 0x4F /* 50Hz Banding AEC 8 LSBs */ 256#define BD50_50HZ_BANDING_AEC_LSBS_SET(x) VAL_SET(x, 0xFF, 0, 0) 257#define BD60 0x50 /* 60Hz Banding AEC 8 LSBs */ 258#define BD60_60HZ_BANDING_AEC_LSBS_SET(x) VAL_SET(x, 0xFF, 0, 0) 259#define REG5A 0x5A /* 50/60Hz Banding Maximum AEC Step */ 260#define BD50_MAX_AEC_STEP_MASK 0xF0 /* 50Hz Banding Max. AEC Step */ 261#define BD60_MAX_AEC_STEP_MASK 0x0F /* 60Hz Banding Max. AEC Step */ 262#define BD50_MAX_AEC_STEP_SET(x) VAL_SET((x - 1), 0x0F, 0, 4) 263#define BD60_MAX_AEC_STEP_SET(x) VAL_SET((x - 1), 0x0F, 0, 0) 264#define REG5D 0x5D /* AVGsel[7:0], 16-zone average weight option */ 265#define REG5E 0x5E /* AVGsel[15:8], 16-zone average weight option */ 266#define REG5F 0x5F /* AVGsel[23:16], 16-zone average weight option */ 267#define REG60 0x60 /* AVGsel[31:24], 16-zone average weight option */ 268#define HISTO_LOW 0x61 /* Histogram Algorithm Low Level */ 269#define HISTO_HIGH 0x62 /* Histogram Algorithm High Level */ 270 271/* 272 * ID 273 */ 274#define MANUFACTURER_ID 0x7FA2 275#define PID_OV2640 0x2642 276#define VERSION(pid, ver) ((pid << 8) | (ver & 0xFF)) 277 278/* 279 * Struct 280 */ 281struct regval_list { 282 u8 reg_num; 283 u8 value; 284}; 285 286struct ov2640_win_size { 287 char *name; 288 u32 width; 289 u32 height; 290 const struct regval_list *regs; 291}; 292 293 294struct ov2640_priv { 295 struct v4l2_subdev subdev; 296 struct media_pad pad; 297 struct v4l2_ctrl_handler hdl; 298 u32 cfmt_code; 299 struct clk *clk; 300 const struct ov2640_win_size *win; 301 302 struct gpio_desc *resetb_gpio; 303 struct gpio_desc *pwdn_gpio; 304 305 struct mutex lock; /* lock to protect streaming and power_count */ 306 bool streaming; 307 int power_count; 308}; 309 310/* 311 * Registers settings 312 */ 313 314#define ENDMARKER { 0xff, 0xff } 315 316static const struct regval_list ov2640_init_regs[] = { 317 { BANK_SEL, BANK_SEL_DSP }, 318 { 0x2c, 0xff }, 319 { 0x2e, 0xdf }, 320 { BANK_SEL, BANK_SEL_SENS }, 321 { 0x3c, 0x32 }, 322 { CLKRC, CLKRC_DIV_SET(1) }, 323 { COM2, COM2_OCAP_Nx_SET(3) }, 324 { REG04, REG04_DEF | REG04_HREF_EN }, 325 { COM8, COM8_DEF | COM8_BNDF_EN | COM8_AGC_EN | COM8_AEC_EN }, 326 { COM9, COM9_AGC_GAIN_8x | 0x08}, 327 { 0x2c, 0x0c }, 328 { 0x33, 0x78 }, 329 { 0x3a, 0x33 }, 330 { 0x3b, 0xfb }, 331 { 0x3e, 0x00 }, 332 { 0x43, 0x11 }, 333 { 0x16, 0x10 }, 334 { 0x39, 0x02 }, 335 { 0x35, 0x88 }, 336 { 0x22, 0x0a }, 337 { 0x37, 0x40 }, 338 { 0x23, 0x00 }, 339 { ARCOM2, 0xa0 }, 340 { 0x06, 0x02 }, 341 { 0x06, 0x88 }, 342 { 0x07, 0xc0 }, 343 { 0x0d, 0xb7 }, 344 { 0x0e, 0x01 }, 345 { 0x4c, 0x00 }, 346 { 0x4a, 0x81 }, 347 { 0x21, 0x99 }, 348 { AEW, 0x40 }, 349 { AEB, 0x38 }, 350 { VV, VV_HIGH_TH_SET(0x08) | VV_LOW_TH_SET(0x02) }, 351 { 0x5c, 0x00 }, 352 { 0x63, 0x00 }, 353 { FLL, 0x22 }, 354 { COM3, 0x38 | COM3_BAND_AUTO }, 355 { REG5D, 0x55 }, 356 { REG5E, 0x7d }, 357 { REG5F, 0x7d }, 358 { REG60, 0x55 }, 359 { HISTO_LOW, 0x70 }, 360 { HISTO_HIGH, 0x80 }, 361 { 0x7c, 0x05 }, 362 { 0x20, 0x80 }, 363 { 0x28, 0x30 }, 364 { 0x6c, 0x00 }, 365 { 0x6d, 0x80 }, 366 { 0x6e, 0x00 }, 367 { 0x70, 0x02 }, 368 { 0x71, 0x94 }, 369 { 0x73, 0xc1 }, 370 { 0x3d, 0x34 }, 371 { COM7, COM7_RES_UXGA | COM7_ZOOM_EN }, 372 { REG5A, BD50_MAX_AEC_STEP_SET(6) 373 | BD60_MAX_AEC_STEP_SET(8) }, /* 0x57 */ 374 { COM25, COM25_50HZ_BANDING_AEC_MSBS_SET(0x0bb) 375 | COM25_60HZ_BANDING_AEC_MSBS_SET(0x09c) }, /* 0x00 */ 376 { BD50, BD50_50HZ_BANDING_AEC_LSBS_SET(0x0bb) }, /* 0xbb */ 377 { BD60, BD60_60HZ_BANDING_AEC_LSBS_SET(0x09c) }, /* 0x9c */ 378 { BANK_SEL, BANK_SEL_DSP }, 379 { 0xe5, 0x7f }, 380 { MC_BIST, MC_BIST_RESET | MC_BIST_BOOT_ROM_SEL }, 381 { 0x41, 0x24 }, 382 { RESET, RESET_JPEG | RESET_DVP }, 383 { 0x76, 0xff }, 384 { 0x33, 0xa0 }, 385 { 0x42, 0x20 }, 386 { 0x43, 0x18 }, 387 { 0x4c, 0x00 }, 388 { CTRL3, CTRL3_BPC_EN | CTRL3_WPC_EN | 0x10 }, 389 { 0x88, 0x3f }, 390 { 0xd7, 0x03 }, 391 { 0xd9, 0x10 }, 392 { R_DVP_SP, R_DVP_SP_AUTO_MODE | 0x2 }, 393 { 0xc8, 0x08 }, 394 { 0xc9, 0x80 }, 395 { BPADDR, 0x00 }, 396 { BPDATA, 0x00 }, 397 { BPADDR, 0x03 }, 398 { BPDATA, 0x48 }, 399 { BPDATA, 0x48 }, 400 { BPADDR, 0x08 }, 401 { BPDATA, 0x20 }, 402 { BPDATA, 0x10 }, 403 { BPDATA, 0x0e }, 404 { 0x90, 0x00 }, 405 { 0x91, 0x0e }, 406 { 0x91, 0x1a }, 407 { 0x91, 0x31 }, 408 { 0x91, 0x5a }, 409 { 0x91, 0x69 }, 410 { 0x91, 0x75 }, 411 { 0x91, 0x7e }, 412 { 0x91, 0x88 }, 413 { 0x91, 0x8f }, 414 { 0x91, 0x96 }, 415 { 0x91, 0xa3 }, 416 { 0x91, 0xaf }, 417 { 0x91, 0xc4 }, 418 { 0x91, 0xd7 }, 419 { 0x91, 0xe8 }, 420 { 0x91, 0x20 }, 421 { 0x92, 0x00 }, 422 { 0x93, 0x06 }, 423 { 0x93, 0xe3 }, 424 { 0x93, 0x03 }, 425 { 0x93, 0x03 }, 426 { 0x93, 0x00 }, 427 { 0x93, 0x02 }, 428 { 0x93, 0x00 }, 429 { 0x93, 0x00 }, 430 { 0x93, 0x00 }, 431 { 0x93, 0x00 }, 432 { 0x93, 0x00 }, 433 { 0x93, 0x00 }, 434 { 0x93, 0x00 }, 435 { 0x96, 0x00 }, 436 { 0x97, 0x08 }, 437 { 0x97, 0x19 }, 438 { 0x97, 0x02 }, 439 { 0x97, 0x0c }, 440 { 0x97, 0x24 }, 441 { 0x97, 0x30 }, 442 { 0x97, 0x28 }, 443 { 0x97, 0x26 }, 444 { 0x97, 0x02 }, 445 { 0x97, 0x98 }, 446 { 0x97, 0x80 }, 447 { 0x97, 0x00 }, 448 { 0x97, 0x00 }, 449 { 0xa4, 0x00 }, 450 { 0xa8, 0x00 }, 451 { 0xc5, 0x11 }, 452 { 0xc6, 0x51 }, 453 { 0xbf, 0x80 }, 454 { 0xc7, 0x10 }, /* simple AWB */ 455 { 0xb6, 0x66 }, 456 { 0xb8, 0xA5 }, 457 { 0xb7, 0x64 }, 458 { 0xb9, 0x7C }, 459 { 0xb3, 0xaf }, 460 { 0xb4, 0x97 }, 461 { 0xb5, 0xFF }, 462 { 0xb0, 0xC5 }, 463 { 0xb1, 0x94 }, 464 { 0xb2, 0x0f }, 465 { 0xc4, 0x5c }, 466 { 0xa6, 0x00 }, 467 { 0xa7, 0x20 }, 468 { 0xa7, 0xd8 }, 469 { 0xa7, 0x1b }, 470 { 0xa7, 0x31 }, 471 { 0xa7, 0x00 }, 472 { 0xa7, 0x18 }, 473 { 0xa7, 0x20 }, 474 { 0xa7, 0xd8 }, 475 { 0xa7, 0x19 }, 476 { 0xa7, 0x31 }, 477 { 0xa7, 0x00 }, 478 { 0xa7, 0x18 }, 479 { 0xa7, 0x20 }, 480 { 0xa7, 0xd8 }, 481 { 0xa7, 0x19 }, 482 { 0xa7, 0x31 }, 483 { 0xa7, 0x00 }, 484 { 0xa7, 0x18 }, 485 { 0x7f, 0x00 }, 486 { 0xe5, 0x1f }, 487 { 0xe1, 0x77 }, 488 { 0xdd, 0x7f }, 489 { CTRL0, CTRL0_YUV422 | CTRL0_YUV_EN | CTRL0_RGB_EN }, 490 ENDMARKER, 491}; 492 493/* 494 * Register settings for window size 495 * The preamble, setup the internal DSP to input an UXGA (1600x1200) image. 496 * Then the different zooming configurations will setup the output image size. 497 */ 498static const struct regval_list ov2640_size_change_preamble_regs[] = { 499 { BANK_SEL, BANK_SEL_DSP }, 500 { RESET, RESET_DVP }, 501 { SIZEL, SIZEL_HSIZE8_11_SET(UXGA_WIDTH) | 502 SIZEL_HSIZE8_SET(UXGA_WIDTH) | 503 SIZEL_VSIZE8_SET(UXGA_HEIGHT) }, 504 { HSIZE8, HSIZE8_SET(UXGA_WIDTH) }, 505 { VSIZE8, VSIZE8_SET(UXGA_HEIGHT) }, 506 { CTRL2, CTRL2_DCW_EN | CTRL2_SDE_EN | 507 CTRL2_UV_AVG_EN | CTRL2_CMX_EN | CTRL2_UV_ADJ_EN }, 508 { HSIZE, HSIZE_SET(UXGA_WIDTH) }, 509 { VSIZE, VSIZE_SET(UXGA_HEIGHT) }, 510 { XOFFL, XOFFL_SET(0) }, 511 { YOFFL, YOFFL_SET(0) }, 512 { VHYX, VHYX_HSIZE_SET(UXGA_WIDTH) | VHYX_VSIZE_SET(UXGA_HEIGHT) | 513 VHYX_XOFF_SET(0) | VHYX_YOFF_SET(0)}, 514 { TEST, TEST_HSIZE_SET(UXGA_WIDTH) }, 515 ENDMARKER, 516}; 517 518#define PER_SIZE_REG_SEQ(x, y, v_div, h_div, pclk_div) \ 519 { CTRLI, CTRLI_LP_DP | CTRLI_V_DIV_SET(v_div) | \ 520 CTRLI_H_DIV_SET(h_div)}, \ 521 { ZMOW, ZMOW_OUTW_SET(x) }, \ 522 { ZMOH, ZMOH_OUTH_SET(y) }, \ 523 { ZMHH, ZMHH_OUTW_SET(x) | ZMHH_OUTH_SET(y) }, \ 524 { R_DVP_SP, pclk_div }, \ 525 { RESET, 0x00} 526 527static const struct regval_list ov2640_qcif_regs[] = { 528 PER_SIZE_REG_SEQ(QCIF_WIDTH, QCIF_HEIGHT, 3, 3, 4), 529 ENDMARKER, 530}; 531 532static const struct regval_list ov2640_qvga_regs[] = { 533 PER_SIZE_REG_SEQ(QVGA_WIDTH, QVGA_HEIGHT, 2, 2, 4), 534 ENDMARKER, 535}; 536 537static const struct regval_list ov2640_cif_regs[] = { 538 PER_SIZE_REG_SEQ(CIF_WIDTH, CIF_HEIGHT, 2, 2, 8), 539 ENDMARKER, 540}; 541 542static const struct regval_list ov2640_vga_regs[] = { 543 PER_SIZE_REG_SEQ(VGA_WIDTH, VGA_HEIGHT, 0, 0, 2), 544 ENDMARKER, 545}; 546 547static const struct regval_list ov2640_svga_regs[] = { 548 PER_SIZE_REG_SEQ(SVGA_WIDTH, SVGA_HEIGHT, 1, 1, 2), 549 ENDMARKER, 550}; 551 552static const struct regval_list ov2640_xga_regs[] = { 553 PER_SIZE_REG_SEQ(XGA_WIDTH, XGA_HEIGHT, 0, 0, 2), 554 { CTRLI, 0x00}, 555 ENDMARKER, 556}; 557 558static const struct regval_list ov2640_sxga_regs[] = { 559 PER_SIZE_REG_SEQ(SXGA_WIDTH, SXGA_HEIGHT, 0, 0, 2), 560 { CTRLI, 0x00}, 561 { R_DVP_SP, 2 | R_DVP_SP_AUTO_MODE }, 562 ENDMARKER, 563}; 564 565static const struct regval_list ov2640_uxga_regs[] = { 566 PER_SIZE_REG_SEQ(UXGA_WIDTH, UXGA_HEIGHT, 0, 0, 0), 567 { CTRLI, 0x00}, 568 { R_DVP_SP, 0 | R_DVP_SP_AUTO_MODE }, 569 ENDMARKER, 570}; 571 572#define OV2640_SIZE(n, w, h, r) \ 573 {.name = n, .width = w , .height = h, .regs = r } 574 575static const struct ov2640_win_size ov2640_supported_win_sizes[] = { 576 OV2640_SIZE("QCIF", QCIF_WIDTH, QCIF_HEIGHT, ov2640_qcif_regs), 577 OV2640_SIZE("QVGA", QVGA_WIDTH, QVGA_HEIGHT, ov2640_qvga_regs), 578 OV2640_SIZE("CIF", CIF_WIDTH, CIF_HEIGHT, ov2640_cif_regs), 579 OV2640_SIZE("VGA", VGA_WIDTH, VGA_HEIGHT, ov2640_vga_regs), 580 OV2640_SIZE("SVGA", SVGA_WIDTH, SVGA_HEIGHT, ov2640_svga_regs), 581 OV2640_SIZE("XGA", XGA_WIDTH, XGA_HEIGHT, ov2640_xga_regs), 582 OV2640_SIZE("SXGA", SXGA_WIDTH, SXGA_HEIGHT, ov2640_sxga_regs), 583 OV2640_SIZE("UXGA", UXGA_WIDTH, UXGA_HEIGHT, ov2640_uxga_regs), 584}; 585 586/* 587 * Register settings for pixel formats 588 */ 589static const struct regval_list ov2640_format_change_preamble_regs[] = { 590 { BANK_SEL, BANK_SEL_DSP }, 591 { R_BYPASS, R_BYPASS_USE_DSP }, 592 ENDMARKER, 593}; 594 595static const struct regval_list ov2640_yuyv_regs[] = { 596 { IMAGE_MODE, IMAGE_MODE_YUV422 }, 597 { 0xd7, 0x03 }, 598 { 0x33, 0xa0 }, 599 { 0xe5, 0x1f }, 600 { 0xe1, 0x67 }, 601 { RESET, 0x00 }, 602 { R_BYPASS, R_BYPASS_USE_DSP }, 603 ENDMARKER, 604}; 605 606static const struct regval_list ov2640_uyvy_regs[] = { 607 { IMAGE_MODE, IMAGE_MODE_LBYTE_FIRST | IMAGE_MODE_YUV422 }, 608 { 0xd7, 0x01 }, 609 { 0x33, 0xa0 }, 610 { 0xe1, 0x67 }, 611 { RESET, 0x00 }, 612 { R_BYPASS, R_BYPASS_USE_DSP }, 613 ENDMARKER, 614}; 615 616static const struct regval_list ov2640_rgb565_be_regs[] = { 617 { IMAGE_MODE, IMAGE_MODE_RGB565 }, 618 { 0xd7, 0x03 }, 619 { RESET, 0x00 }, 620 { R_BYPASS, R_BYPASS_USE_DSP }, 621 ENDMARKER, 622}; 623 624static const struct regval_list ov2640_rgb565_le_regs[] = { 625 { IMAGE_MODE, IMAGE_MODE_LBYTE_FIRST | IMAGE_MODE_RGB565 }, 626 { 0xd7, 0x03 }, 627 { RESET, 0x00 }, 628 { R_BYPASS, R_BYPASS_USE_DSP }, 629 ENDMARKER, 630}; 631 632static u32 ov2640_codes[] = { 633 MEDIA_BUS_FMT_YUYV8_2X8, 634 MEDIA_BUS_FMT_UYVY8_2X8, 635 MEDIA_BUS_FMT_YVYU8_2X8, 636 MEDIA_BUS_FMT_VYUY8_2X8, 637 MEDIA_BUS_FMT_RGB565_2X8_BE, 638 MEDIA_BUS_FMT_RGB565_2X8_LE, 639}; 640 641/* 642 * General functions 643 */ 644static struct ov2640_priv *to_ov2640(const struct i2c_client *client) 645{ 646 return container_of(i2c_get_clientdata(client), struct ov2640_priv, 647 subdev); 648} 649 650static int ov2640_write_array(struct i2c_client *client, 651 const struct regval_list *vals) 652{ 653 int ret; 654 655 while ((vals->reg_num != 0xff) || (vals->value != 0xff)) { 656 ret = i2c_smbus_write_byte_data(client, 657 vals->reg_num, vals->value); 658 dev_vdbg(&client->dev, "array: 0x%02x, 0x%02x", 659 vals->reg_num, vals->value); 660 661 if (ret < 0) 662 return ret; 663 vals++; 664 } 665 return 0; 666} 667 668static int ov2640_mask_set(struct i2c_client *client, 669 u8 reg, u8 mask, u8 set) 670{ 671 s32 val = i2c_smbus_read_byte_data(client, reg); 672 if (val < 0) 673 return val; 674 675 val &= ~mask; 676 val |= set & mask; 677 678 dev_vdbg(&client->dev, "masks: 0x%02x, 0x%02x", reg, val); 679 680 return i2c_smbus_write_byte_data(client, reg, val); 681} 682 683static int ov2640_reset(struct i2c_client *client) 684{ 685 int ret; 686 static const struct regval_list reset_seq[] = { 687 {BANK_SEL, BANK_SEL_SENS}, 688 {COM7, COM7_SRST}, 689 ENDMARKER, 690 }; 691 692 ret = ov2640_write_array(client, reset_seq); 693 if (ret) 694 goto err; 695 696 msleep(5); 697err: 698 dev_dbg(&client->dev, "%s: (ret %d)", __func__, ret); 699 return ret; 700} 701 702static const char * const ov2640_test_pattern_menu[] = { 703 "Disabled", 704 "Eight Vertical Colour Bars", 705}; 706 707/* 708 * functions 709 */ 710static int ov2640_s_ctrl(struct v4l2_ctrl *ctrl) 711{ 712 struct v4l2_subdev *sd = 713 &container_of(ctrl->handler, struct ov2640_priv, hdl)->subdev; 714 struct i2c_client *client = v4l2_get_subdevdata(sd); 715 struct ov2640_priv *priv = to_ov2640(client); 716 u8 val; 717 int ret; 718 719 /* v4l2_ctrl_lock() locks our own mutex */ 720 721 /* 722 * If the device is not powered up by the host driver, do not apply any 723 * controls to H/W at this time. Instead the controls will be restored 724 * when the streaming is started. 725 */ 726 if (!priv->power_count) 727 return 0; 728 729 ret = i2c_smbus_write_byte_data(client, BANK_SEL, BANK_SEL_SENS); 730 if (ret < 0) 731 return ret; 732 733 switch (ctrl->id) { 734 case V4L2_CID_VFLIP: 735 val = ctrl->val ? REG04_VFLIP_IMG | REG04_VREF_EN : 0x00; 736 return ov2640_mask_set(client, REG04, 737 REG04_VFLIP_IMG | REG04_VREF_EN, val); 738 /* NOTE: REG04_VREF_EN: 1 line shift / even/odd line swap */ 739 case V4L2_CID_HFLIP: 740 val = ctrl->val ? REG04_HFLIP_IMG : 0x00; 741 return ov2640_mask_set(client, REG04, REG04_HFLIP_IMG, val); 742 case V4L2_CID_TEST_PATTERN: 743 val = ctrl->val ? COM7_COLOR_BAR_TEST : 0x00; 744 return ov2640_mask_set(client, COM7, COM7_COLOR_BAR_TEST, val); 745 } 746 747 return -EINVAL; 748} 749 750#ifdef CONFIG_VIDEO_ADV_DEBUG 751static int ov2640_g_register(struct v4l2_subdev *sd, 752 struct v4l2_dbg_register *reg) 753{ 754 struct i2c_client *client = v4l2_get_subdevdata(sd); 755 int ret; 756 757 reg->size = 1; 758 if (reg->reg > 0xff) 759 return -EINVAL; 760 761 ret = i2c_smbus_read_byte_data(client, reg->reg); 762 if (ret < 0) 763 return ret; 764 765 reg->val = ret; 766 767 return 0; 768} 769 770static int ov2640_s_register(struct v4l2_subdev *sd, 771 const struct v4l2_dbg_register *reg) 772{ 773 struct i2c_client *client = v4l2_get_subdevdata(sd); 774 775 if (reg->reg > 0xff || 776 reg->val > 0xff) 777 return -EINVAL; 778 779 return i2c_smbus_write_byte_data(client, reg->reg, reg->val); 780} 781#endif 782 783static void ov2640_set_power(struct ov2640_priv *priv, int on) 784{ 785#ifdef CONFIG_GPIOLIB 786 if (priv->pwdn_gpio) 787 gpiod_direction_output(priv->pwdn_gpio, !on); 788 if (on && priv->resetb_gpio) { 789 /* Active the resetb pin to perform a reset pulse */ 790 gpiod_direction_output(priv->resetb_gpio, 1); 791 usleep_range(3000, 5000); 792 gpiod_set_value(priv->resetb_gpio, 0); 793 } 794#endif 795} 796 797static int ov2640_s_power(struct v4l2_subdev *sd, int on) 798{ 799 struct i2c_client *client = v4l2_get_subdevdata(sd); 800 struct ov2640_priv *priv = to_ov2640(client); 801 802 mutex_lock(&priv->lock); 803 804 /* 805 * If the power count is modified from 0 to != 0 or from != 0 to 0, 806 * update the power state. 807 */ 808 if (priv->power_count == !on) 809 ov2640_set_power(priv, on); 810 priv->power_count += on ? 1 : -1; 811 WARN_ON(priv->power_count < 0); 812 mutex_unlock(&priv->lock); 813 814 return 0; 815} 816 817/* Select the nearest higher resolution for capture */ 818static const struct ov2640_win_size *ov2640_select_win(u32 width, u32 height) 819{ 820 int i, default_size = ARRAY_SIZE(ov2640_supported_win_sizes) - 1; 821 822 for (i = 0; i < ARRAY_SIZE(ov2640_supported_win_sizes); i++) { 823 if (ov2640_supported_win_sizes[i].width >= width && 824 ov2640_supported_win_sizes[i].height >= height) 825 return &ov2640_supported_win_sizes[i]; 826 } 827 828 return &ov2640_supported_win_sizes[default_size]; 829} 830 831static int ov2640_set_params(struct i2c_client *client, 832 const struct ov2640_win_size *win, u32 code) 833{ 834 const struct regval_list *selected_cfmt_regs; 835 u8 val; 836 int ret; 837 838 switch (code) { 839 case MEDIA_BUS_FMT_RGB565_2X8_BE: 840 dev_dbg(&client->dev, "%s: Selected cfmt RGB565 BE", __func__); 841 selected_cfmt_regs = ov2640_rgb565_be_regs; 842 break; 843 case MEDIA_BUS_FMT_RGB565_2X8_LE: 844 dev_dbg(&client->dev, "%s: Selected cfmt RGB565 LE", __func__); 845 selected_cfmt_regs = ov2640_rgb565_le_regs; 846 break; 847 case MEDIA_BUS_FMT_YUYV8_2X8: 848 dev_dbg(&client->dev, "%s: Selected cfmt YUYV (YUV422)", __func__); 849 selected_cfmt_regs = ov2640_yuyv_regs; 850 break; 851 case MEDIA_BUS_FMT_UYVY8_2X8: 852 default: 853 dev_dbg(&client->dev, "%s: Selected cfmt UYVY", __func__); 854 selected_cfmt_regs = ov2640_uyvy_regs; 855 break; 856 case MEDIA_BUS_FMT_YVYU8_2X8: 857 dev_dbg(&client->dev, "%s: Selected cfmt YVYU", __func__); 858 selected_cfmt_regs = ov2640_yuyv_regs; 859 break; 860 case MEDIA_BUS_FMT_VYUY8_2X8: 861 dev_dbg(&client->dev, "%s: Selected cfmt VYUY", __func__); 862 selected_cfmt_regs = ov2640_uyvy_regs; 863 break; 864 } 865 866 /* reset hardware */ 867 ov2640_reset(client); 868 869 /* initialize the sensor with default data */ 870 dev_dbg(&client->dev, "%s: Init default", __func__); 871 ret = ov2640_write_array(client, ov2640_init_regs); 872 if (ret < 0) 873 goto err; 874 875 /* select preamble */ 876 dev_dbg(&client->dev, "%s: Set size to %s", __func__, win->name); 877 ret = ov2640_write_array(client, ov2640_size_change_preamble_regs); 878 if (ret < 0) 879 goto err; 880 881 /* set size win */ 882 ret = ov2640_write_array(client, win->regs); 883 if (ret < 0) 884 goto err; 885 886 /* cfmt preamble */ 887 dev_dbg(&client->dev, "%s: Set cfmt", __func__); 888 ret = ov2640_write_array(client, ov2640_format_change_preamble_regs); 889 if (ret < 0) 890 goto err; 891 892 /* set cfmt */ 893 ret = ov2640_write_array(client, selected_cfmt_regs); 894 if (ret < 0) 895 goto err; 896 val = (code == MEDIA_BUS_FMT_YVYU8_2X8) 897 || (code == MEDIA_BUS_FMT_VYUY8_2X8) ? CTRL0_VFIRST : 0x00; 898 ret = ov2640_mask_set(client, CTRL0, CTRL0_VFIRST, val); 899 if (ret < 0) 900 goto err; 901 902 return 0; 903 904err: 905 dev_err(&client->dev, "%s: Error %d", __func__, ret); 906 ov2640_reset(client); 907 908 return ret; 909} 910 911static int ov2640_get_fmt(struct v4l2_subdev *sd, 912 struct v4l2_subdev_state *sd_state, 913 struct v4l2_subdev_format *format) 914{ 915 struct v4l2_mbus_framefmt *mf = &format->format; 916 struct i2c_client *client = v4l2_get_subdevdata(sd); 917 struct ov2640_priv *priv = to_ov2640(client); 918 919 if (format->pad) 920 return -EINVAL; 921 922 if (format->which == V4L2_SUBDEV_FORMAT_TRY) { 923 mf = v4l2_subdev_state_get_format(sd_state, 0); 924 format->format = *mf; 925 return 0; 926 } 927 928 mf->width = priv->win->width; 929 mf->height = priv->win->height; 930 mf->code = priv->cfmt_code; 931 mf->colorspace = V4L2_COLORSPACE_SRGB; 932 mf->field = V4L2_FIELD_NONE; 933 mf->ycbcr_enc = V4L2_YCBCR_ENC_DEFAULT; 934 mf->quantization = V4L2_QUANTIZATION_DEFAULT; 935 mf->xfer_func = V4L2_XFER_FUNC_DEFAULT; 936 937 return 0; 938} 939 940static int ov2640_set_fmt(struct v4l2_subdev *sd, 941 struct v4l2_subdev_state *sd_state, 942 struct v4l2_subdev_format *format) 943{ 944 struct v4l2_mbus_framefmt *mf = &format->format; 945 struct i2c_client *client = v4l2_get_subdevdata(sd); 946 struct ov2640_priv *priv = to_ov2640(client); 947 const struct ov2640_win_size *win; 948 int ret = 0; 949 950 if (format->pad) 951 return -EINVAL; 952 953 mutex_lock(&priv->lock); 954 955 /* select suitable win */ 956 win = ov2640_select_win(mf->width, mf->height); 957 mf->width = win->width; 958 mf->height = win->height; 959 960 mf->field = V4L2_FIELD_NONE; 961 mf->colorspace = V4L2_COLORSPACE_SRGB; 962 mf->ycbcr_enc = V4L2_YCBCR_ENC_DEFAULT; 963 mf->quantization = V4L2_QUANTIZATION_DEFAULT; 964 mf->xfer_func = V4L2_XFER_FUNC_DEFAULT; 965 966 switch (mf->code) { 967 case MEDIA_BUS_FMT_RGB565_2X8_BE: 968 case MEDIA_BUS_FMT_RGB565_2X8_LE: 969 case MEDIA_BUS_FMT_YUYV8_2X8: 970 case MEDIA_BUS_FMT_UYVY8_2X8: 971 case MEDIA_BUS_FMT_YVYU8_2X8: 972 case MEDIA_BUS_FMT_VYUY8_2X8: 973 break; 974 default: 975 mf->code = MEDIA_BUS_FMT_UYVY8_2X8; 976 break; 977 } 978 979 if (format->which == V4L2_SUBDEV_FORMAT_ACTIVE) { 980 struct ov2640_priv *priv = to_ov2640(client); 981 982 if (priv->streaming) { 983 ret = -EBUSY; 984 goto out; 985 } 986 /* select win */ 987 priv->win = win; 988 /* select format */ 989 priv->cfmt_code = mf->code; 990 } else { 991 *v4l2_subdev_state_get_format(sd_state, 0) = *mf; 992 } 993out: 994 mutex_unlock(&priv->lock); 995 996 return ret; 997} 998 999static int ov2640_init_state(struct v4l2_subdev *sd, 1000 struct v4l2_subdev_state *sd_state) 1001{ 1002 struct v4l2_mbus_framefmt *try_fmt = 1003 v4l2_subdev_state_get_format(sd_state, 0); 1004 const struct ov2640_win_size *win = 1005 ov2640_select_win(SVGA_WIDTH, SVGA_HEIGHT); 1006 1007 try_fmt->width = win->width; 1008 try_fmt->height = win->height; 1009 try_fmt->code = MEDIA_BUS_FMT_UYVY8_2X8; 1010 try_fmt->colorspace = V4L2_COLORSPACE_SRGB; 1011 try_fmt->field = V4L2_FIELD_NONE; 1012 try_fmt->ycbcr_enc = V4L2_YCBCR_ENC_DEFAULT; 1013 try_fmt->quantization = V4L2_QUANTIZATION_DEFAULT; 1014 try_fmt->xfer_func = V4L2_XFER_FUNC_DEFAULT; 1015 1016 return 0; 1017} 1018 1019static int ov2640_enum_mbus_code(struct v4l2_subdev *sd, 1020 struct v4l2_subdev_state *sd_state, 1021 struct v4l2_subdev_mbus_code_enum *code) 1022{ 1023 if (code->pad || code->index >= ARRAY_SIZE(ov2640_codes)) 1024 return -EINVAL; 1025 1026 code->code = ov2640_codes[code->index]; 1027 return 0; 1028} 1029 1030static int ov2640_get_selection(struct v4l2_subdev *sd, 1031 struct v4l2_subdev_state *sd_state, 1032 struct v4l2_subdev_selection *sel) 1033{ 1034 if (sel->which != V4L2_SUBDEV_FORMAT_ACTIVE) 1035 return -EINVAL; 1036 1037 switch (sel->target) { 1038 case V4L2_SEL_TGT_CROP_BOUNDS: 1039 case V4L2_SEL_TGT_CROP: 1040 sel->r.left = 0; 1041 sel->r.top = 0; 1042 sel->r.width = UXGA_WIDTH; 1043 sel->r.height = UXGA_HEIGHT; 1044 return 0; 1045 default: 1046 return -EINVAL; 1047 } 1048} 1049 1050static int ov2640_s_stream(struct v4l2_subdev *sd, int on) 1051{ 1052 struct i2c_client *client = v4l2_get_subdevdata(sd); 1053 struct ov2640_priv *priv = to_ov2640(client); 1054 int ret = 0; 1055 1056 mutex_lock(&priv->lock); 1057 if (priv->streaming == !on) { 1058 if (on) { 1059 ret = ov2640_set_params(client, priv->win, 1060 priv->cfmt_code); 1061 if (!ret) 1062 ret = __v4l2_ctrl_handler_setup(&priv->hdl); 1063 } 1064 } 1065 if (!ret) 1066 priv->streaming = on; 1067 mutex_unlock(&priv->lock); 1068 1069 return ret; 1070} 1071 1072static int ov2640_video_probe(struct i2c_client *client) 1073{ 1074 struct ov2640_priv *priv = to_ov2640(client); 1075 u8 pid, ver, midh, midl; 1076 const char *devname; 1077 int ret; 1078 1079 ret = ov2640_s_power(&priv->subdev, 1); 1080 if (ret < 0) 1081 return ret; 1082 1083 /* 1084 * check and show product ID and manufacturer ID 1085 */ 1086 i2c_smbus_write_byte_data(client, BANK_SEL, BANK_SEL_SENS); 1087 pid = i2c_smbus_read_byte_data(client, PID); 1088 ver = i2c_smbus_read_byte_data(client, VER); 1089 midh = i2c_smbus_read_byte_data(client, MIDH); 1090 midl = i2c_smbus_read_byte_data(client, MIDL); 1091 1092 switch (VERSION(pid, ver)) { 1093 case PID_OV2640: 1094 devname = "ov2640"; 1095 break; 1096 default: 1097 dev_err(&client->dev, 1098 "Product ID error %x:%x\n", pid, ver); 1099 ret = -ENODEV; 1100 goto done; 1101 } 1102 1103 dev_info(&client->dev, 1104 "%s Product ID %0x:%0x Manufacturer ID %x:%x\n", 1105 devname, pid, ver, midh, midl); 1106 1107done: 1108 ov2640_s_power(&priv->subdev, 0); 1109 return ret; 1110} 1111 1112static const struct v4l2_ctrl_ops ov2640_ctrl_ops = { 1113 .s_ctrl = ov2640_s_ctrl, 1114}; 1115 1116static const struct v4l2_subdev_core_ops ov2640_subdev_core_ops = { 1117 .log_status = v4l2_ctrl_subdev_log_status, 1118 .subscribe_event = v4l2_ctrl_subdev_subscribe_event, 1119 .unsubscribe_event = v4l2_event_subdev_unsubscribe, 1120#ifdef CONFIG_VIDEO_ADV_DEBUG 1121 .g_register = ov2640_g_register, 1122 .s_register = ov2640_s_register, 1123#endif 1124 .s_power = ov2640_s_power, 1125}; 1126 1127static const struct v4l2_subdev_pad_ops ov2640_subdev_pad_ops = { 1128 .enum_mbus_code = ov2640_enum_mbus_code, 1129 .get_selection = ov2640_get_selection, 1130 .get_fmt = ov2640_get_fmt, 1131 .set_fmt = ov2640_set_fmt, 1132}; 1133 1134static const struct v4l2_subdev_video_ops ov2640_subdev_video_ops = { 1135 .s_stream = ov2640_s_stream, 1136}; 1137 1138static const struct v4l2_subdev_ops ov2640_subdev_ops = { 1139 .core = &ov2640_subdev_core_ops, 1140 .pad = &ov2640_subdev_pad_ops, 1141 .video = &ov2640_subdev_video_ops, 1142}; 1143 1144static const struct v4l2_subdev_internal_ops ov2640_internal_ops = { 1145 .init_state = ov2640_init_state, 1146}; 1147 1148static int ov2640_probe_dt(struct i2c_client *client, 1149 struct ov2640_priv *priv) 1150{ 1151 int ret; 1152 1153 /* Request the reset GPIO deasserted */ 1154 priv->resetb_gpio = devm_gpiod_get_optional(&client->dev, "resetb", 1155 GPIOD_OUT_LOW); 1156 1157 if (!priv->resetb_gpio) 1158 dev_dbg(&client->dev, "resetb gpio is not assigned!\n"); 1159 1160 ret = PTR_ERR_OR_ZERO(priv->resetb_gpio); 1161 if (ret && ret != -ENOSYS) { 1162 dev_dbg(&client->dev, 1163 "Error %d while getting resetb gpio\n", ret); 1164 return ret; 1165 } 1166 1167 /* Request the power down GPIO asserted */ 1168 priv->pwdn_gpio = devm_gpiod_get_optional(&client->dev, "pwdn", 1169 GPIOD_OUT_HIGH); 1170 1171 if (!priv->pwdn_gpio) 1172 dev_dbg(&client->dev, "pwdn gpio is not assigned!\n"); 1173 1174 ret = PTR_ERR_OR_ZERO(priv->pwdn_gpio); 1175 if (ret && ret != -ENOSYS) { 1176 dev_dbg(&client->dev, 1177 "Error %d while getting pwdn gpio\n", ret); 1178 return ret; 1179 } 1180 1181 return 0; 1182} 1183 1184/* 1185 * i2c_driver functions 1186 */ 1187static int ov2640_probe(struct i2c_client *client) 1188{ 1189 struct ov2640_priv *priv; 1190 struct i2c_adapter *adapter = client->adapter; 1191 int ret; 1192 1193 if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA)) { 1194 dev_err(&adapter->dev, 1195 "OV2640: I2C-Adapter doesn't support SMBUS\n"); 1196 return -EIO; 1197 } 1198 1199 priv = devm_kzalloc(&client->dev, sizeof(*priv), GFP_KERNEL); 1200 if (!priv) 1201 return -ENOMEM; 1202 1203 if (client->dev.of_node) { 1204 priv->clk = devm_clk_get_enabled(&client->dev, "xvclk"); 1205 if (IS_ERR(priv->clk)) 1206 return PTR_ERR(priv->clk); 1207 } 1208 1209 ret = ov2640_probe_dt(client, priv); 1210 if (ret) 1211 return ret; 1212 1213 priv->win = ov2640_select_win(SVGA_WIDTH, SVGA_HEIGHT); 1214 priv->cfmt_code = MEDIA_BUS_FMT_UYVY8_2X8; 1215 1216 v4l2_i2c_subdev_init(&priv->subdev, client, &ov2640_subdev_ops); 1217 priv->subdev.internal_ops = &ov2640_internal_ops; 1218 priv->subdev.flags |= V4L2_SUBDEV_FL_HAS_DEVNODE | 1219 V4L2_SUBDEV_FL_HAS_EVENTS; 1220 mutex_init(&priv->lock); 1221 v4l2_ctrl_handler_init(&priv->hdl, 3); 1222 priv->hdl.lock = &priv->lock; 1223 v4l2_ctrl_new_std(&priv->hdl, &ov2640_ctrl_ops, 1224 V4L2_CID_VFLIP, 0, 1, 1, 0); 1225 v4l2_ctrl_new_std(&priv->hdl, &ov2640_ctrl_ops, 1226 V4L2_CID_HFLIP, 0, 1, 1, 0); 1227 v4l2_ctrl_new_std_menu_items(&priv->hdl, &ov2640_ctrl_ops, 1228 V4L2_CID_TEST_PATTERN, 1229 ARRAY_SIZE(ov2640_test_pattern_menu) - 1, 0, 0, 1230 ov2640_test_pattern_menu); 1231 priv->subdev.ctrl_handler = &priv->hdl; 1232 if (priv->hdl.error) { 1233 ret = priv->hdl.error; 1234 goto err_hdl; 1235 } 1236 priv->pad.flags = MEDIA_PAD_FL_SOURCE; 1237 priv->subdev.entity.function = MEDIA_ENT_F_CAM_SENSOR; 1238 ret = media_entity_pads_init(&priv->subdev.entity, 1, &priv->pad); 1239 if (ret < 0) 1240 goto err_hdl; 1241 1242 ret = ov2640_video_probe(client); 1243 if (ret < 0) 1244 goto err_videoprobe; 1245 1246 ret = v4l2_async_register_subdev(&priv->subdev); 1247 if (ret < 0) 1248 goto err_videoprobe; 1249 1250 dev_info(&adapter->dev, "OV2640 Probed\n"); 1251 1252 return 0; 1253 1254err_videoprobe: 1255 media_entity_cleanup(&priv->subdev.entity); 1256err_hdl: 1257 v4l2_ctrl_handler_free(&priv->hdl); 1258 mutex_destroy(&priv->lock); 1259 return ret; 1260} 1261 1262static void ov2640_remove(struct i2c_client *client) 1263{ 1264 struct ov2640_priv *priv = to_ov2640(client); 1265 1266 v4l2_async_unregister_subdev(&priv->subdev); 1267 v4l2_ctrl_handler_free(&priv->hdl); 1268 mutex_destroy(&priv->lock); 1269 media_entity_cleanup(&priv->subdev.entity); 1270 v4l2_device_unregister_subdev(&priv->subdev); 1271} 1272 1273static const struct i2c_device_id ov2640_id[] = { 1274 { "ov2640", 0 }, 1275 { } 1276}; 1277MODULE_DEVICE_TABLE(i2c, ov2640_id); 1278 1279static const struct of_device_id ov2640_of_match[] = { 1280 {.compatible = "ovti,ov2640", }, 1281 {}, 1282}; 1283MODULE_DEVICE_TABLE(of, ov2640_of_match); 1284 1285static struct i2c_driver ov2640_i2c_driver = { 1286 .driver = { 1287 .name = "ov2640", 1288 .of_match_table = ov2640_of_match, 1289 }, 1290 .probe = ov2640_probe, 1291 .remove = ov2640_remove, 1292 .id_table = ov2640_id, 1293}; 1294 1295module_i2c_driver(ov2640_i2c_driver); 1296 1297MODULE_DESCRIPTION("Driver for Omni Vision 2640 sensor"); 1298MODULE_AUTHOR("Alberto Panizzo"); 1299MODULE_LICENSE("GPL v2"); 1300