1// SPDX-License-Identifier: GPL-2.0-only 2/* 3 * Windfarm PowerMac thermal control. iMac G5 iSight 4 * 5 * (c) Copyright 2007 ��tienne Bersac <bersace@gmail.com> 6 * 7 * Bits & pieces from windfarm_pm81.c by (c) Copyright 2005 Benjamin 8 * Herrenschmidt, IBM Corp. <benh@kernel.crashing.org> 9 * 10 * PowerMac12,1 11 * ============ 12 * 13 * The algorithm used is the PID control algorithm, used the same way 14 * the published Darwin code does, using the same values that are 15 * present in the Darwin 8.10 snapshot property lists (note however 16 * that none of the code has been re-used, it's a complete 17 * re-implementation 18 * 19 * There is two models using PowerMac12,1. Model 2 is iMac G5 iSight 20 * 17" while Model 3 is iMac G5 20". They do have both the same 21 * controls with a tiny difference. The control-ids of hard-drive-fan 22 * and cpu-fan is swapped. 23 * 24 * Target Correction : 25 * 26 * controls have a target correction calculated as : 27 * 28 * new_min = ((((average_power * slope) >> 16) + offset) >> 16) + min_value 29 * new_value = max(new_value, max(new_min, 0)) 30 * 31 * OD Fan control correction. 32 * 33 * # model_id: 2 34 * offset : -19563152 35 * slope : 1956315 36 * 37 * # model_id: 3 38 * offset : -15650652 39 * slope : 1565065 40 * 41 * HD Fan control correction. 42 * 43 * # model_id: 2 44 * offset : -15650652 45 * slope : 1565065 46 * 47 * # model_id: 3 48 * offset : -19563152 49 * slope : 1956315 50 * 51 * CPU Fan control correction. 52 * 53 * # model_id: 2 54 * offset : -25431900 55 * slope : 2543190 56 * 57 * # model_id: 3 58 * offset : -15650652 59 * slope : 1565065 60 * 61 * Target rubber-banding : 62 * 63 * Some controls have a target correction which depends on another 64 * control value. The correction is computed in the following way : 65 * 66 * new_min = ref_value * slope + offset 67 * 68 * ref_value is the value of the reference control. If new_min is 69 * greater than 0, then we correct the target value using : 70 * 71 * new_target = max (new_target, new_min >> 16) 72 * 73 * # model_id : 2 74 * control : cpu-fan 75 * ref : optical-drive-fan 76 * offset : -15650652 77 * slope : 1565065 78 * 79 * # model_id : 3 80 * control : optical-drive-fan 81 * ref : hard-drive-fan 82 * offset : -32768000 83 * slope : 65536 84 * 85 * In order to have the moste efficient correction with those 86 * dependencies, we must trigger HD loop before OD loop before CPU 87 * loop. 88 * 89 * The various control loops found in Darwin config file are: 90 * 91 * HD Fan control loop. 92 * 93 * # model_id: 2 94 * control : hard-drive-fan 95 * sensor : hard-drive-temp 96 * PID params : G_d = 0x00000000 97 * G_p = 0x002D70A3 98 * G_r = 0x00019999 99 * History = 2 entries 100 * Input target = 0x370000 101 * Interval = 5s 102 * 103 * # model_id: 3 104 * control : hard-drive-fan 105 * sensor : hard-drive-temp 106 * PID params : G_d = 0x00000000 107 * G_p = 0x002170A3 108 * G_r = 0x00019999 109 * History = 2 entries 110 * Input target = 0x370000 111 * Interval = 5s 112 * 113 * OD Fan control loop. 114 * 115 * # model_id: 2 116 * control : optical-drive-fan 117 * sensor : optical-drive-temp 118 * PID params : G_d = 0x00000000 119 * G_p = 0x001FAE14 120 * G_r = 0x00019999 121 * History = 2 entries 122 * Input target = 0x320000 123 * Interval = 5s 124 * 125 * # model_id: 3 126 * control : optical-drive-fan 127 * sensor : optical-drive-temp 128 * PID params : G_d = 0x00000000 129 * G_p = 0x001FAE14 130 * G_r = 0x00019999 131 * History = 2 entries 132 * Input target = 0x320000 133 * Interval = 5s 134 * 135 * GPU Fan control loop. 136 * 137 * # model_id: 2 138 * control : hard-drive-fan 139 * sensor : gpu-temp 140 * PID params : G_d = 0x00000000 141 * G_p = 0x002A6666 142 * G_r = 0x00019999 143 * History = 2 entries 144 * Input target = 0x5A0000 145 * Interval = 5s 146 * 147 * # model_id: 3 148 * control : cpu-fan 149 * sensor : gpu-temp 150 * PID params : G_d = 0x00000000 151 * G_p = 0x0010CCCC 152 * G_r = 0x00019999 153 * History = 2 entries 154 * Input target = 0x500000 155 * Interval = 5s 156 * 157 * KODIAK (aka northbridge) Fan control loop. 158 * 159 * # model_id: 2 160 * control : optical-drive-fan 161 * sensor : north-bridge-temp 162 * PID params : G_d = 0x00000000 163 * G_p = 0x003BD70A 164 * G_r = 0x00019999 165 * History = 2 entries 166 * Input target = 0x550000 167 * Interval = 5s 168 * 169 * # model_id: 3 170 * control : hard-drive-fan 171 * sensor : north-bridge-temp 172 * PID params : G_d = 0x00000000 173 * G_p = 0x0030F5C2 174 * G_r = 0x00019999 175 * History = 2 entries 176 * Input target = 0x550000 177 * Interval = 5s 178 * 179 * CPU Fan control loop. 180 * 181 * control : cpu-fan 182 * sensors : cpu-temp, cpu-power 183 * PID params : from SDB partition 184 * 185 * CPU Slew control loop. 186 * 187 * control : cpufreq-clamp 188 * sensor : cpu-temp 189 */ 190 191#undef DEBUG 192 193#include <linux/types.h> 194#include <linux/errno.h> 195#include <linux/kernel.h> 196#include <linux/delay.h> 197#include <linux/slab.h> 198#include <linux/init.h> 199#include <linux/spinlock.h> 200#include <linux/wait.h> 201#include <linux/kmod.h> 202#include <linux/device.h> 203#include <linux/platform_device.h> 204#include <linux/of.h> 205 206#include <asm/machdep.h> 207#include <asm/io.h> 208#include <asm/sections.h> 209#include <asm/smu.h> 210 211#include "windfarm.h" 212#include "windfarm_pid.h" 213 214#define VERSION "0.3" 215 216static int pm121_mach_model; /* machine model id */ 217 218/* Controls & sensors */ 219static struct wf_sensor *sensor_cpu_power; 220static struct wf_sensor *sensor_cpu_temp; 221static struct wf_sensor *sensor_cpu_voltage; 222static struct wf_sensor *sensor_cpu_current; 223static struct wf_sensor *sensor_gpu_temp; 224static struct wf_sensor *sensor_north_bridge_temp; 225static struct wf_sensor *sensor_hard_drive_temp; 226static struct wf_sensor *sensor_optical_drive_temp; 227static struct wf_sensor *sensor_incoming_air_temp; /* unused ! */ 228 229enum { 230 FAN_CPU, 231 FAN_HD, 232 FAN_OD, 233 CPUFREQ, 234 N_CONTROLS 235}; 236static struct wf_control *controls[N_CONTROLS] = {}; 237 238/* Set to kick the control loop into life */ 239static int pm121_all_controls_ok, pm121_all_sensors_ok; 240static bool pm121_started; 241 242enum { 243 FAILURE_FAN = 1 << 0, 244 FAILURE_SENSOR = 1 << 1, 245 FAILURE_OVERTEMP = 1 << 2 246}; 247 248/* All sys loops. Note the HD before the OD loop in order to have it 249 run before. */ 250enum { 251 LOOP_GPU, /* control = hd or cpu, but luckily, 252 it doesn't matter */ 253 LOOP_HD, /* control = hd */ 254 LOOP_KODIAK, /* control = hd or od */ 255 LOOP_OD, /* control = od */ 256 N_LOOPS 257}; 258 259static const char *loop_names[N_LOOPS] = { 260 "GPU", 261 "HD", 262 "KODIAK", 263 "OD", 264}; 265 266#define PM121_NUM_CONFIGS 2 267 268static unsigned int pm121_failure_state; 269static int pm121_readjust, pm121_skipping; 270static bool pm121_overtemp; 271static s32 average_power; 272 273struct pm121_correction { 274 int offset; 275 int slope; 276}; 277 278static struct pm121_correction corrections[N_CONTROLS][PM121_NUM_CONFIGS] = { 279 /* FAN_OD */ 280 { 281 /* MODEL 2 */ 282 { .offset = -19563152, 283 .slope = 1956315 284 }, 285 /* MODEL 3 */ 286 { .offset = -15650652, 287 .slope = 1565065 288 }, 289 }, 290 /* FAN_HD */ 291 { 292 /* MODEL 2 */ 293 { .offset = -15650652, 294 .slope = 1565065 295 }, 296 /* MODEL 3 */ 297 { .offset = -19563152, 298 .slope = 1956315 299 }, 300 }, 301 /* FAN_CPU */ 302 { 303 /* MODEL 2 */ 304 { .offset = -25431900, 305 .slope = 2543190 306 }, 307 /* MODEL 3 */ 308 { .offset = -15650652, 309 .slope = 1565065 310 }, 311 }, 312 /* CPUFREQ has no correction (and is not implemented at all) */ 313}; 314 315struct pm121_connection { 316 unsigned int control_id; 317 unsigned int ref_id; 318 struct pm121_correction correction; 319}; 320 321static struct pm121_connection pm121_connections[] = { 322 /* MODEL 2 */ 323 { .control_id = FAN_CPU, 324 .ref_id = FAN_OD, 325 { .offset = -32768000, 326 .slope = 65536 327 } 328 }, 329 /* MODEL 3 */ 330 { .control_id = FAN_OD, 331 .ref_id = FAN_HD, 332 { .offset = -32768000, 333 .slope = 65536 334 } 335 }, 336}; 337 338/* pointer to the current model connection */ 339static struct pm121_connection *pm121_connection; 340 341/* 342 * ****** System Fans Control Loop ****** 343 * 344 */ 345 346/* Since each loop handles only one control and we want to avoid 347 * writing virtual control, we store the control correction with the 348 * loop params. Some data are not set, there are common to all loop 349 * and thus, hardcoded. 350 */ 351struct pm121_sys_param { 352 /* purely informative since we use mach_model-2 as index */ 353 int model_id; 354 struct wf_sensor **sensor; /* use sensor_id instead ? */ 355 s32 gp, itarget; 356 unsigned int control_id; 357}; 358 359static struct pm121_sys_param 360pm121_sys_all_params[N_LOOPS][PM121_NUM_CONFIGS] = { 361 /* GPU Fan control loop */ 362 { 363 { .model_id = 2, 364 .sensor = &sensor_gpu_temp, 365 .gp = 0x002A6666, 366 .itarget = 0x5A0000, 367 .control_id = FAN_HD, 368 }, 369 { .model_id = 3, 370 .sensor = &sensor_gpu_temp, 371 .gp = 0x0010CCCC, 372 .itarget = 0x500000, 373 .control_id = FAN_CPU, 374 }, 375 }, 376 /* HD Fan control loop */ 377 { 378 { .model_id = 2, 379 .sensor = &sensor_hard_drive_temp, 380 .gp = 0x002D70A3, 381 .itarget = 0x370000, 382 .control_id = FAN_HD, 383 }, 384 { .model_id = 3, 385 .sensor = &sensor_hard_drive_temp, 386 .gp = 0x002170A3, 387 .itarget = 0x370000, 388 .control_id = FAN_HD, 389 }, 390 }, 391 /* KODIAK Fan control loop */ 392 { 393 { .model_id = 2, 394 .sensor = &sensor_north_bridge_temp, 395 .gp = 0x003BD70A, 396 .itarget = 0x550000, 397 .control_id = FAN_OD, 398 }, 399 { .model_id = 3, 400 .sensor = &sensor_north_bridge_temp, 401 .gp = 0x0030F5C2, 402 .itarget = 0x550000, 403 .control_id = FAN_HD, 404 }, 405 }, 406 /* OD Fan control loop */ 407 { 408 { .model_id = 2, 409 .sensor = &sensor_optical_drive_temp, 410 .gp = 0x001FAE14, 411 .itarget = 0x320000, 412 .control_id = FAN_OD, 413 }, 414 { .model_id = 3, 415 .sensor = &sensor_optical_drive_temp, 416 .gp = 0x001FAE14, 417 .itarget = 0x320000, 418 .control_id = FAN_OD, 419 }, 420 }, 421}; 422 423/* the hardcoded values */ 424#define PM121_SYS_GD 0x00000000 425#define PM121_SYS_GR 0x00019999 426#define PM121_SYS_HISTORY_SIZE 2 427#define PM121_SYS_INTERVAL 5 428 429/* State data used by the system fans control loop 430 */ 431struct pm121_sys_state { 432 int ticks; 433 s32 setpoint; 434 struct wf_pid_state pid; 435}; 436 437static struct pm121_sys_state *pm121_sys_state[N_LOOPS] = {}; 438 439/* 440 * ****** CPU Fans Control Loop ****** 441 * 442 */ 443 444#define PM121_CPU_INTERVAL 1 445 446/* State data used by the cpu fans control loop 447 */ 448struct pm121_cpu_state { 449 int ticks; 450 s32 setpoint; 451 struct wf_cpu_pid_state pid; 452}; 453 454static struct pm121_cpu_state *pm121_cpu_state; 455 456 457 458/* 459 * ***** Implementation ***** 460 * 461 */ 462 463/* correction the value using the output-low-bound correction algo */ 464static s32 pm121_correct(s32 new_setpoint, 465 unsigned int control_id, 466 s32 min) 467{ 468 s32 new_min; 469 struct pm121_correction *correction; 470 correction = &corrections[control_id][pm121_mach_model - 2]; 471 472 new_min = (average_power * correction->slope) >> 16; 473 new_min += correction->offset; 474 new_min = (new_min >> 16) + min; 475 476 return max3(new_setpoint, new_min, 0); 477} 478 479static s32 pm121_connect(unsigned int control_id, s32 setpoint) 480{ 481 s32 new_min, value, new_setpoint; 482 483 if (pm121_connection->control_id == control_id) { 484 controls[control_id]->ops->get_value(controls[control_id], 485 &value); 486 new_min = value * pm121_connection->correction.slope; 487 new_min += pm121_connection->correction.offset; 488 if (new_min > 0) { 489 new_setpoint = max(setpoint, (new_min >> 16)); 490 if (new_setpoint != setpoint) { 491 pr_debug("pm121: %s depending on %s, " 492 "corrected from %d to %d RPM\n", 493 controls[control_id]->name, 494 controls[pm121_connection->ref_id]->name, 495 (int) setpoint, (int) new_setpoint); 496 } 497 } else 498 new_setpoint = setpoint; 499 } 500 /* no connection */ 501 else 502 new_setpoint = setpoint; 503 504 return new_setpoint; 505} 506 507/* FAN LOOPS */ 508static void pm121_create_sys_fans(int loop_id) 509{ 510 struct pm121_sys_param *param = NULL; 511 struct wf_pid_param pid_param; 512 struct wf_control *control = NULL; 513 int i; 514 515 /* First, locate the params for this model */ 516 for (i = 0; i < PM121_NUM_CONFIGS; i++) { 517 if (pm121_sys_all_params[loop_id][i].model_id == pm121_mach_model) { 518 param = &(pm121_sys_all_params[loop_id][i]); 519 break; 520 } 521 } 522 523 /* No params found, put fans to max */ 524 if (param == NULL) { 525 printk(KERN_WARNING "pm121: %s fan config not found " 526 " for this machine model\n", 527 loop_names[loop_id]); 528 goto fail; 529 } 530 531 control = controls[param->control_id]; 532 533 /* Alloc & initialize state */ 534 pm121_sys_state[loop_id] = kmalloc(sizeof(struct pm121_sys_state), 535 GFP_KERNEL); 536 if (pm121_sys_state[loop_id] == NULL) { 537 printk(KERN_WARNING "pm121: Memory allocation error\n"); 538 goto fail; 539 } 540 pm121_sys_state[loop_id]->ticks = 1; 541 542 /* Fill PID params */ 543 pid_param.gd = PM121_SYS_GD; 544 pid_param.gp = param->gp; 545 pid_param.gr = PM121_SYS_GR; 546 pid_param.interval = PM121_SYS_INTERVAL; 547 pid_param.history_len = PM121_SYS_HISTORY_SIZE; 548 pid_param.itarget = param->itarget; 549 if(control) 550 { 551 pid_param.min = control->ops->get_min(control); 552 pid_param.max = control->ops->get_max(control); 553 } else { 554 /* 555 * This is probably not the right!? 556 * Perhaps goto fail if control == NULL above? 557 */ 558 pid_param.min = 0; 559 pid_param.max = 0; 560 } 561 562 wf_pid_init(&pm121_sys_state[loop_id]->pid, &pid_param); 563 564 pr_debug("pm121: %s Fan control loop initialized.\n" 565 " itarged=%d.%03d, min=%d RPM, max=%d RPM\n", 566 loop_names[loop_id], FIX32TOPRINT(pid_param.itarget), 567 pid_param.min, pid_param.max); 568 return; 569 570 fail: 571 /* note that this is not optimal since another loop may still 572 control the same control */ 573 printk(KERN_WARNING "pm121: failed to set up %s loop " 574 "setting \"%s\" to max speed.\n", 575 loop_names[loop_id], control ? control->name : "uninitialized value"); 576 577 if (control) 578 wf_control_set_max(control); 579} 580 581static void pm121_sys_fans_tick(int loop_id) 582{ 583 struct pm121_sys_param *param; 584 struct pm121_sys_state *st; 585 struct wf_sensor *sensor; 586 struct wf_control *control; 587 s32 temp, new_setpoint; 588 int rc; 589 590 param = &(pm121_sys_all_params[loop_id][pm121_mach_model-2]); 591 st = pm121_sys_state[loop_id]; 592 sensor = *(param->sensor); 593 control = controls[param->control_id]; 594 595 if (--st->ticks != 0) { 596 if (pm121_readjust) 597 goto readjust; 598 return; 599 } 600 st->ticks = PM121_SYS_INTERVAL; 601 602 rc = sensor->ops->get_value(sensor, &temp); 603 if (rc) { 604 printk(KERN_WARNING "windfarm: %s sensor error %d\n", 605 sensor->name, rc); 606 pm121_failure_state |= FAILURE_SENSOR; 607 return; 608 } 609 610 pr_debug("pm121: %s Fan tick ! %s: %d.%03d\n", 611 loop_names[loop_id], sensor->name, 612 FIX32TOPRINT(temp)); 613 614 new_setpoint = wf_pid_run(&st->pid, temp); 615 616 /* correction */ 617 new_setpoint = pm121_correct(new_setpoint, 618 param->control_id, 619 st->pid.param.min); 620 /* linked corretion */ 621 new_setpoint = pm121_connect(param->control_id, new_setpoint); 622 623 if (new_setpoint == st->setpoint) 624 return; 625 st->setpoint = new_setpoint; 626 pr_debug("pm121: %s corrected setpoint: %d RPM\n", 627 control->name, (int)new_setpoint); 628 readjust: 629 if (control && pm121_failure_state == 0) { 630 rc = control->ops->set_value(control, st->setpoint); 631 if (rc) { 632 printk(KERN_WARNING "windfarm: %s fan error %d\n", 633 control->name, rc); 634 pm121_failure_state |= FAILURE_FAN; 635 } 636 } 637} 638 639 640/* CPU LOOP */ 641static void pm121_create_cpu_fans(void) 642{ 643 struct wf_cpu_pid_param pid_param; 644 const struct smu_sdbp_header *hdr; 645 struct smu_sdbp_cpupiddata *piddata; 646 struct smu_sdbp_fvt *fvt; 647 struct wf_control *fan_cpu; 648 s32 tmax, tdelta, maxpow, powadj; 649 650 fan_cpu = controls[FAN_CPU]; 651 652 /* First, locate the PID params in SMU SBD */ 653 hdr = smu_get_sdb_partition(SMU_SDB_CPUPIDDATA_ID, NULL); 654 if (!hdr) { 655 printk(KERN_WARNING "pm121: CPU PID fan config not found.\n"); 656 goto fail; 657 } 658 piddata = (struct smu_sdbp_cpupiddata *)&hdr[1]; 659 660 /* Get the FVT params for operating point 0 (the only supported one 661 * for now) in order to get tmax 662 */ 663 hdr = smu_get_sdb_partition(SMU_SDB_FVT_ID, NULL); 664 if (hdr) { 665 fvt = (struct smu_sdbp_fvt *)&hdr[1]; 666 tmax = ((s32)fvt->maxtemp) << 16; 667 } else 668 tmax = 0x5e0000; /* 94 degree default */ 669 670 /* Alloc & initialize state */ 671 pm121_cpu_state = kmalloc(sizeof(struct pm121_cpu_state), 672 GFP_KERNEL); 673 if (pm121_cpu_state == NULL) 674 goto fail; 675 pm121_cpu_state->ticks = 1; 676 677 /* Fill PID params */ 678 pid_param.interval = PM121_CPU_INTERVAL; 679 pid_param.history_len = piddata->history_len; 680 if (pid_param.history_len > WF_CPU_PID_MAX_HISTORY) { 681 printk(KERN_WARNING "pm121: History size overflow on " 682 "CPU control loop (%d)\n", piddata->history_len); 683 pid_param.history_len = WF_CPU_PID_MAX_HISTORY; 684 } 685 pid_param.gd = piddata->gd; 686 pid_param.gp = piddata->gp; 687 pid_param.gr = piddata->gr / pid_param.history_len; 688 689 tdelta = ((s32)piddata->target_temp_delta) << 16; 690 maxpow = ((s32)piddata->max_power) << 16; 691 powadj = ((s32)piddata->power_adj) << 16; 692 693 pid_param.tmax = tmax; 694 pid_param.ttarget = tmax - tdelta; 695 pid_param.pmaxadj = maxpow - powadj; 696 697 pid_param.min = fan_cpu->ops->get_min(fan_cpu); 698 pid_param.max = fan_cpu->ops->get_max(fan_cpu); 699 700 wf_cpu_pid_init(&pm121_cpu_state->pid, &pid_param); 701 702 pr_debug("pm121: CPU Fan control initialized.\n"); 703 pr_debug(" ttarget=%d.%03d, tmax=%d.%03d, min=%d RPM, max=%d RPM,\n", 704 FIX32TOPRINT(pid_param.ttarget), FIX32TOPRINT(pid_param.tmax), 705 pid_param.min, pid_param.max); 706 707 return; 708 709 fail: 710 printk(KERN_WARNING "pm121: CPU fan config not found, max fan speed\n"); 711 712 if (controls[CPUFREQ]) 713 wf_control_set_max(controls[CPUFREQ]); 714 if (fan_cpu) 715 wf_control_set_max(fan_cpu); 716} 717 718 719static void pm121_cpu_fans_tick(struct pm121_cpu_state *st) 720{ 721 s32 new_setpoint, temp, power; 722 struct wf_control *fan_cpu = NULL; 723 int rc; 724 725 if (--st->ticks != 0) { 726 if (pm121_readjust) 727 goto readjust; 728 return; 729 } 730 st->ticks = PM121_CPU_INTERVAL; 731 732 fan_cpu = controls[FAN_CPU]; 733 734 rc = sensor_cpu_temp->ops->get_value(sensor_cpu_temp, &temp); 735 if (rc) { 736 printk(KERN_WARNING "pm121: CPU temp sensor error %d\n", 737 rc); 738 pm121_failure_state |= FAILURE_SENSOR; 739 return; 740 } 741 742 rc = sensor_cpu_power->ops->get_value(sensor_cpu_power, &power); 743 if (rc) { 744 printk(KERN_WARNING "pm121: CPU power sensor error %d\n", 745 rc); 746 pm121_failure_state |= FAILURE_SENSOR; 747 return; 748 } 749 750 pr_debug("pm121: CPU Fans tick ! CPU temp: %d.%03d��C, power: %d.%03d\n", 751 FIX32TOPRINT(temp), FIX32TOPRINT(power)); 752 753 if (temp > st->pid.param.tmax) 754 pm121_failure_state |= FAILURE_OVERTEMP; 755 756 new_setpoint = wf_cpu_pid_run(&st->pid, power, temp); 757 758 /* correction */ 759 new_setpoint = pm121_correct(new_setpoint, 760 FAN_CPU, 761 st->pid.param.min); 762 763 /* connected correction */ 764 new_setpoint = pm121_connect(FAN_CPU, new_setpoint); 765 766 if (st->setpoint == new_setpoint) 767 return; 768 st->setpoint = new_setpoint; 769 pr_debug("pm121: CPU corrected setpoint: %d RPM\n", (int)new_setpoint); 770 771 readjust: 772 if (fan_cpu && pm121_failure_state == 0) { 773 rc = fan_cpu->ops->set_value(fan_cpu, st->setpoint); 774 if (rc) { 775 printk(KERN_WARNING "pm121: %s fan error %d\n", 776 fan_cpu->name, rc); 777 pm121_failure_state |= FAILURE_FAN; 778 } 779 } 780} 781 782/* 783 * ****** Common ****** 784 * 785 */ 786 787static void pm121_tick(void) 788{ 789 unsigned int last_failure = pm121_failure_state; 790 unsigned int new_failure; 791 s32 total_power; 792 int i; 793 794 if (!pm121_started) { 795 pr_debug("pm121: creating control loops !\n"); 796 for (i = 0; i < N_LOOPS; i++) 797 pm121_create_sys_fans(i); 798 799 pm121_create_cpu_fans(); 800 pm121_started = true; 801 } 802 803 /* skipping ticks */ 804 if (pm121_skipping && --pm121_skipping) 805 return; 806 807 /* compute average power */ 808 total_power = 0; 809 for (i = 0; i < pm121_cpu_state->pid.param.history_len; i++) 810 total_power += pm121_cpu_state->pid.powers[i]; 811 812 average_power = total_power / pm121_cpu_state->pid.param.history_len; 813 814 815 pm121_failure_state = 0; 816 for (i = 0 ; i < N_LOOPS; i++) { 817 if (pm121_sys_state[i]) 818 pm121_sys_fans_tick(i); 819 } 820 821 if (pm121_cpu_state) 822 pm121_cpu_fans_tick(pm121_cpu_state); 823 824 pm121_readjust = 0; 825 new_failure = pm121_failure_state & ~last_failure; 826 827 /* If entering failure mode, clamp cpufreq and ramp all 828 * fans to full speed. 829 */ 830 if (pm121_failure_state && !last_failure) { 831 for (i = 0; i < N_CONTROLS; i++) { 832 if (controls[i]) 833 wf_control_set_max(controls[i]); 834 } 835 } 836 837 /* If leaving failure mode, unclamp cpufreq and readjust 838 * all fans on next iteration 839 */ 840 if (!pm121_failure_state && last_failure) { 841 if (controls[CPUFREQ]) 842 wf_control_set_min(controls[CPUFREQ]); 843 pm121_readjust = 1; 844 } 845 846 /* Overtemp condition detected, notify and start skipping a couple 847 * ticks to let the temperature go down 848 */ 849 if (new_failure & FAILURE_OVERTEMP) { 850 wf_set_overtemp(); 851 pm121_skipping = 2; 852 pm121_overtemp = true; 853 } 854 855 /* We only clear the overtemp condition if overtemp is cleared 856 * _and_ no other failure is present. Since a sensor error will 857 * clear the overtemp condition (can't measure temperature) at 858 * the control loop levels, but we don't want to keep it clear 859 * here in this case 860 */ 861 if (!pm121_failure_state && pm121_overtemp) { 862 wf_clear_overtemp(); 863 pm121_overtemp = false; 864 } 865} 866 867 868static struct wf_control* pm121_register_control(struct wf_control *ct, 869 const char *match, 870 unsigned int id) 871{ 872 if (controls[id] == NULL && !strcmp(ct->name, match)) { 873 if (wf_get_control(ct) == 0) 874 controls[id] = ct; 875 } 876 return controls[id]; 877} 878 879static void pm121_new_control(struct wf_control *ct) 880{ 881 int all = 1; 882 883 if (pm121_all_controls_ok) 884 return; 885 886 all = pm121_register_control(ct, "optical-drive-fan", FAN_OD) && all; 887 all = pm121_register_control(ct, "hard-drive-fan", FAN_HD) && all; 888 all = pm121_register_control(ct, "cpu-fan", FAN_CPU) && all; 889 all = pm121_register_control(ct, "cpufreq-clamp", CPUFREQ) && all; 890 891 if (all) 892 pm121_all_controls_ok = 1; 893} 894 895 896 897 898static struct wf_sensor* pm121_register_sensor(struct wf_sensor *sensor, 899 const char *match, 900 struct wf_sensor **var) 901{ 902 if (*var == NULL && !strcmp(sensor->name, match)) { 903 if (wf_get_sensor(sensor) == 0) 904 *var = sensor; 905 } 906 return *var; 907} 908 909static void pm121_new_sensor(struct wf_sensor *sr) 910{ 911 int all = 1; 912 913 if (pm121_all_sensors_ok) 914 return; 915 916 all = pm121_register_sensor(sr, "cpu-temp", 917 &sensor_cpu_temp) && all; 918 all = pm121_register_sensor(sr, "cpu-current", 919 &sensor_cpu_current) && all; 920 all = pm121_register_sensor(sr, "cpu-voltage", 921 &sensor_cpu_voltage) && all; 922 all = pm121_register_sensor(sr, "cpu-power", 923 &sensor_cpu_power) && all; 924 all = pm121_register_sensor(sr, "hard-drive-temp", 925 &sensor_hard_drive_temp) && all; 926 all = pm121_register_sensor(sr, "optical-drive-temp", 927 &sensor_optical_drive_temp) && all; 928 all = pm121_register_sensor(sr, "incoming-air-temp", 929 &sensor_incoming_air_temp) && all; 930 all = pm121_register_sensor(sr, "north-bridge-temp", 931 &sensor_north_bridge_temp) && all; 932 all = pm121_register_sensor(sr, "gpu-temp", 933 &sensor_gpu_temp) && all; 934 935 if (all) 936 pm121_all_sensors_ok = 1; 937} 938 939 940 941static int pm121_notify(struct notifier_block *self, 942 unsigned long event, void *data) 943{ 944 switch (event) { 945 case WF_EVENT_NEW_CONTROL: 946 pr_debug("pm121: new control %s detected\n", 947 ((struct wf_control *)data)->name); 948 pm121_new_control(data); 949 break; 950 case WF_EVENT_NEW_SENSOR: 951 pr_debug("pm121: new sensor %s detected\n", 952 ((struct wf_sensor *)data)->name); 953 pm121_new_sensor(data); 954 break; 955 case WF_EVENT_TICK: 956 if (pm121_all_controls_ok && pm121_all_sensors_ok) 957 pm121_tick(); 958 break; 959 } 960 961 return 0; 962} 963 964static struct notifier_block pm121_events = { 965 .notifier_call = pm121_notify, 966}; 967 968static int pm121_init_pm(void) 969{ 970 const struct smu_sdbp_header *hdr; 971 972 hdr = smu_get_sdb_partition(SMU_SDB_SENSORTREE_ID, NULL); 973 if (hdr) { 974 struct smu_sdbp_sensortree *st = 975 (struct smu_sdbp_sensortree *)&hdr[1]; 976 pm121_mach_model = st->model_id; 977 } 978 979 pm121_connection = &pm121_connections[pm121_mach_model - 2]; 980 981 printk(KERN_INFO "pm121: Initializing for iMac G5 iSight model ID %d\n", 982 pm121_mach_model); 983 984 return 0; 985} 986 987 988static int pm121_probe(struct platform_device *ddev) 989{ 990 wf_register_client(&pm121_events); 991 992 return 0; 993} 994 995static void pm121_remove(struct platform_device *ddev) 996{ 997 wf_unregister_client(&pm121_events); 998} 999 1000static struct platform_driver pm121_driver = { 1001 .probe = pm121_probe, 1002 .remove_new = pm121_remove, 1003 .driver = { 1004 .name = "windfarm", 1005 .bus = &platform_bus_type, 1006 }, 1007}; 1008 1009 1010static int __init pm121_init(void) 1011{ 1012 int rc = -ENODEV; 1013 1014 if (of_machine_is_compatible("PowerMac12,1")) 1015 rc = pm121_init_pm(); 1016 1017 if (rc == 0) { 1018 request_module("windfarm_smu_controls"); 1019 request_module("windfarm_smu_sensors"); 1020 request_module("windfarm_smu_sat"); 1021 request_module("windfarm_lm75_sensor"); 1022 request_module("windfarm_max6690_sensor"); 1023 request_module("windfarm_cpufreq_clamp"); 1024 platform_driver_register(&pm121_driver); 1025 } 1026 1027 return rc; 1028} 1029 1030static void __exit pm121_exit(void) 1031{ 1032 1033 platform_driver_unregister(&pm121_driver); 1034} 1035 1036 1037module_init(pm121_init); 1038module_exit(pm121_exit); 1039 1040MODULE_AUTHOR("��tienne Bersac <bersace@gmail.com>"); 1041MODULE_DESCRIPTION("Thermal control logic for iMac G5 (iSight)"); 1042MODULE_LICENSE("GPL"); 1043 1044