1// SPDX-License-Identifier: GPL-2.0+ 2/* 3 * HID driver for Nintendo Switch Joy-Cons and Pro Controllers 4 * 5 * Copyright (c) 2019-2021 Daniel J. Ogorchock <djogorchock@gmail.com> 6 * Portions Copyright (c) 2020 Nadia Holmquist Pedersen <nadia@nhp.sh> 7 * Copyright (c) 2022 Emily Strickland <linux@emily.st> 8 * Copyright (c) 2023 Ryan McClelland <rymcclel@gmail.com> 9 * 10 * The following resources/projects were referenced for this driver: 11 * https://github.com/dekuNukem/Nintendo_Switch_Reverse_Engineering 12 * https://gitlab.com/pjranki/joycon-linux-kernel (Peter Rankin) 13 * https://github.com/FrotBot/SwitchProConLinuxUSB 14 * https://github.com/MTCKC/ProconXInput 15 * https://github.com/Davidobot/BetterJoyForCemu 16 * hid-wiimote kernel hid driver 17 * hid-logitech-hidpp driver 18 * hid-sony driver 19 * 20 * This driver supports the Nintendo Switch Joy-Cons and Pro Controllers. The 21 * Pro Controllers can either be used over USB or Bluetooth. 22 * 23 * This driver also incorporates support for Nintendo Switch Online controllers 24 * for the NES, SNES, Sega Genesis, and N64. 25 * 26 * The driver will retrieve the factory calibration info from the controllers, 27 * so little to no user calibration should be required. 28 * 29 */ 30 31#include "hid-ids.h" 32#include <asm/unaligned.h> 33#include <linux/delay.h> 34#include <linux/device.h> 35#include <linux/kernel.h> 36#include <linux/hid.h> 37#include <linux/input.h> 38#include <linux/jiffies.h> 39#include <linux/leds.h> 40#include <linux/module.h> 41#include <linux/power_supply.h> 42#include <linux/spinlock.h> 43 44/* 45 * Reference the url below for the following HID report defines: 46 * https://github.com/dekuNukem/Nintendo_Switch_Reverse_Engineering 47 */ 48 49/* Output Reports */ 50#define JC_OUTPUT_RUMBLE_AND_SUBCMD 0x01 51#define JC_OUTPUT_FW_UPDATE_PKT 0x03 52#define JC_OUTPUT_RUMBLE_ONLY 0x10 53#define JC_OUTPUT_MCU_DATA 0x11 54#define JC_OUTPUT_USB_CMD 0x80 55 56/* Subcommand IDs */ 57#define JC_SUBCMD_STATE 0x00 58#define JC_SUBCMD_MANUAL_BT_PAIRING 0x01 59#define JC_SUBCMD_REQ_DEV_INFO 0x02 60#define JC_SUBCMD_SET_REPORT_MODE 0x03 61#define JC_SUBCMD_TRIGGERS_ELAPSED 0x04 62#define JC_SUBCMD_GET_PAGE_LIST_STATE 0x05 63#define JC_SUBCMD_SET_HCI_STATE 0x06 64#define JC_SUBCMD_RESET_PAIRING_INFO 0x07 65#define JC_SUBCMD_LOW_POWER_MODE 0x08 66#define JC_SUBCMD_SPI_FLASH_READ 0x10 67#define JC_SUBCMD_SPI_FLASH_WRITE 0x11 68#define JC_SUBCMD_RESET_MCU 0x20 69#define JC_SUBCMD_SET_MCU_CONFIG 0x21 70#define JC_SUBCMD_SET_MCU_STATE 0x22 71#define JC_SUBCMD_SET_PLAYER_LIGHTS 0x30 72#define JC_SUBCMD_GET_PLAYER_LIGHTS 0x31 73#define JC_SUBCMD_SET_HOME_LIGHT 0x38 74#define JC_SUBCMD_ENABLE_IMU 0x40 75#define JC_SUBCMD_SET_IMU_SENSITIVITY 0x41 76#define JC_SUBCMD_WRITE_IMU_REG 0x42 77#define JC_SUBCMD_READ_IMU_REG 0x43 78#define JC_SUBCMD_ENABLE_VIBRATION 0x48 79#define JC_SUBCMD_GET_REGULATED_VOLTAGE 0x50 80 81/* Input Reports */ 82#define JC_INPUT_BUTTON_EVENT 0x3F 83#define JC_INPUT_SUBCMD_REPLY 0x21 84#define JC_INPUT_IMU_DATA 0x30 85#define JC_INPUT_MCU_DATA 0x31 86#define JC_INPUT_USB_RESPONSE 0x81 87 88/* Feature Reports */ 89#define JC_FEATURE_LAST_SUBCMD 0x02 90#define JC_FEATURE_OTA_FW_UPGRADE 0x70 91#define JC_FEATURE_SETUP_MEM_READ 0x71 92#define JC_FEATURE_MEM_READ 0x72 93#define JC_FEATURE_ERASE_MEM_SECTOR 0x73 94#define JC_FEATURE_MEM_WRITE 0x74 95#define JC_FEATURE_LAUNCH 0x75 96 97/* USB Commands */ 98#define JC_USB_CMD_CONN_STATUS 0x01 99#define JC_USB_CMD_HANDSHAKE 0x02 100#define JC_USB_CMD_BAUDRATE_3M 0x03 101#define JC_USB_CMD_NO_TIMEOUT 0x04 102#define JC_USB_CMD_EN_TIMEOUT 0x05 103#define JC_USB_RESET 0x06 104#define JC_USB_PRE_HANDSHAKE 0x91 105#define JC_USB_SEND_UART 0x92 106 107/* Magic value denoting presence of user calibration */ 108#define JC_CAL_USR_MAGIC_0 0xB2 109#define JC_CAL_USR_MAGIC_1 0xA1 110#define JC_CAL_USR_MAGIC_SIZE 2 111 112/* SPI storage addresses of user calibration data */ 113#define JC_CAL_USR_LEFT_MAGIC_ADDR 0x8010 114#define JC_CAL_USR_LEFT_DATA_ADDR 0x8012 115#define JC_CAL_USR_LEFT_DATA_END 0x801A 116#define JC_CAL_USR_RIGHT_MAGIC_ADDR 0x801B 117#define JC_CAL_USR_RIGHT_DATA_ADDR 0x801D 118#define JC_CAL_STICK_DATA_SIZE \ 119 (JC_CAL_USR_LEFT_DATA_END - JC_CAL_USR_LEFT_DATA_ADDR + 1) 120 121/* SPI storage addresses of factory calibration data */ 122#define JC_CAL_FCT_DATA_LEFT_ADDR 0x603d 123#define JC_CAL_FCT_DATA_RIGHT_ADDR 0x6046 124 125/* SPI storage addresses of IMU factory calibration data */ 126#define JC_IMU_CAL_FCT_DATA_ADDR 0x6020 127#define JC_IMU_CAL_FCT_DATA_END 0x6037 128#define JC_IMU_CAL_DATA_SIZE \ 129 (JC_IMU_CAL_FCT_DATA_END - JC_IMU_CAL_FCT_DATA_ADDR + 1) 130/* SPI storage addresses of IMU user calibration data */ 131#define JC_IMU_CAL_USR_MAGIC_ADDR 0x8026 132#define JC_IMU_CAL_USR_DATA_ADDR 0x8028 133 134/* The raw analog joystick values will be mapped in terms of this magnitude */ 135#define JC_MAX_STICK_MAG 32767 136#define JC_STICK_FUZZ 250 137#define JC_STICK_FLAT 500 138 139/* Hat values for pro controller's d-pad */ 140#define JC_MAX_DPAD_MAG 1 141#define JC_DPAD_FUZZ 0 142#define JC_DPAD_FLAT 0 143 144/* Under most circumstances IMU reports are pushed every 15ms; use as default */ 145#define JC_IMU_DFLT_AVG_DELTA_MS 15 146/* How many samples to sum before calculating average IMU report delta */ 147#define JC_IMU_SAMPLES_PER_DELTA_AVG 300 148/* Controls how many dropped IMU packets at once trigger a warning message */ 149#define JC_IMU_DROPPED_PKT_WARNING 3 150 151/* 152 * The controller's accelerometer has a sensor resolution of 16bits and is 153 * configured with a range of +-8000 milliGs. Therefore, the resolution can be 154 * calculated thus: (2^16-1)/(8000 * 2) = 4.096 digits per milliG 155 * Resolution per G (rather than per millliG): 4.096 * 1000 = 4096 digits per G 156 * Alternatively: 1/4096 = .0002441 Gs per digit 157 */ 158#define JC_IMU_MAX_ACCEL_MAG 32767 159#define JC_IMU_ACCEL_RES_PER_G 4096 160#define JC_IMU_ACCEL_FUZZ 10 161#define JC_IMU_ACCEL_FLAT 0 162 163/* 164 * The controller's gyroscope has a sensor resolution of 16bits and is 165 * configured with a range of +-2000 degrees/second. 166 * Digits per dps: (2^16 -1)/(2000*2) = 16.38375 167 * dps per digit: 16.38375E-1 = .0610 168 * 169 * STMicro recommends in the datasheet to add 15% to the dps/digit. This allows 170 * the full sensitivity range to be saturated without clipping. This yields more 171 * accurate results, so it's the technique this driver uses. 172 * dps per digit (corrected): .0610 * 1.15 = .0702 173 * digits per dps (corrected): .0702E-1 = 14.247 174 * 175 * Now, 14.247 truncating to 14 loses a lot of precision, so we rescale the 176 * min/max range by 1000. 177 */ 178#define JC_IMU_PREC_RANGE_SCALE 1000 179/* Note: change mag and res_per_dps if prec_range_scale is ever altered */ 180#define JC_IMU_MAX_GYRO_MAG 32767000 /* (2^16-1)*1000 */ 181#define JC_IMU_GYRO_RES_PER_DPS 14247 /* (14.247*1000) */ 182#define JC_IMU_GYRO_FUZZ 10 183#define JC_IMU_GYRO_FLAT 0 184 185/* frequency/amplitude tables for rumble */ 186struct joycon_rumble_freq_data { 187 u16 high; 188 u8 low; 189 u16 freq; /* Hz*/ 190}; 191 192struct joycon_rumble_amp_data { 193 u8 high; 194 u16 low; 195 u16 amp; 196}; 197 198#if IS_ENABLED(CONFIG_NINTENDO_FF) 199/* 200 * These tables are from 201 * https://github.com/dekuNukem/Nintendo_Switch_Reverse_Engineering/blob/master/rumble_data_table.md 202 */ 203static const struct joycon_rumble_freq_data joycon_rumble_frequencies[] = { 204 /* high, low, freq */ 205 { 0x0000, 0x01, 41 }, { 0x0000, 0x02, 42 }, { 0x0000, 0x03, 43 }, 206 { 0x0000, 0x04, 44 }, { 0x0000, 0x05, 45 }, { 0x0000, 0x06, 46 }, 207 { 0x0000, 0x07, 47 }, { 0x0000, 0x08, 48 }, { 0x0000, 0x09, 49 }, 208 { 0x0000, 0x0A, 50 }, { 0x0000, 0x0B, 51 }, { 0x0000, 0x0C, 52 }, 209 { 0x0000, 0x0D, 53 }, { 0x0000, 0x0E, 54 }, { 0x0000, 0x0F, 55 }, 210 { 0x0000, 0x10, 57 }, { 0x0000, 0x11, 58 }, { 0x0000, 0x12, 59 }, 211 { 0x0000, 0x13, 60 }, { 0x0000, 0x14, 62 }, { 0x0000, 0x15, 63 }, 212 { 0x0000, 0x16, 64 }, { 0x0000, 0x17, 66 }, { 0x0000, 0x18, 67 }, 213 { 0x0000, 0x19, 69 }, { 0x0000, 0x1A, 70 }, { 0x0000, 0x1B, 72 }, 214 { 0x0000, 0x1C, 73 }, { 0x0000, 0x1D, 75 }, { 0x0000, 0x1e, 77 }, 215 { 0x0000, 0x1f, 78 }, { 0x0000, 0x20, 80 }, { 0x0400, 0x21, 82 }, 216 { 0x0800, 0x22, 84 }, { 0x0c00, 0x23, 85 }, { 0x1000, 0x24, 87 }, 217 { 0x1400, 0x25, 89 }, { 0x1800, 0x26, 91 }, { 0x1c00, 0x27, 93 }, 218 { 0x2000, 0x28, 95 }, { 0x2400, 0x29, 97 }, { 0x2800, 0x2a, 99 }, 219 { 0x2c00, 0x2b, 102 }, { 0x3000, 0x2c, 104 }, { 0x3400, 0x2d, 106 }, 220 { 0x3800, 0x2e, 108 }, { 0x3c00, 0x2f, 111 }, { 0x4000, 0x30, 113 }, 221 { 0x4400, 0x31, 116 }, { 0x4800, 0x32, 118 }, { 0x4c00, 0x33, 121 }, 222 { 0x5000, 0x34, 123 }, { 0x5400, 0x35, 126 }, { 0x5800, 0x36, 129 }, 223 { 0x5c00, 0x37, 132 }, { 0x6000, 0x38, 135 }, { 0x6400, 0x39, 137 }, 224 { 0x6800, 0x3a, 141 }, { 0x6c00, 0x3b, 144 }, { 0x7000, 0x3c, 147 }, 225 { 0x7400, 0x3d, 150 }, { 0x7800, 0x3e, 153 }, { 0x7c00, 0x3f, 157 }, 226 { 0x8000, 0x40, 160 }, { 0x8400, 0x41, 164 }, { 0x8800, 0x42, 167 }, 227 { 0x8c00, 0x43, 171 }, { 0x9000, 0x44, 174 }, { 0x9400, 0x45, 178 }, 228 { 0x9800, 0x46, 182 }, { 0x9c00, 0x47, 186 }, { 0xa000, 0x48, 190 }, 229 { 0xa400, 0x49, 194 }, { 0xa800, 0x4a, 199 }, { 0xac00, 0x4b, 203 }, 230 { 0xb000, 0x4c, 207 }, { 0xb400, 0x4d, 212 }, { 0xb800, 0x4e, 217 }, 231 { 0xbc00, 0x4f, 221 }, { 0xc000, 0x50, 226 }, { 0xc400, 0x51, 231 }, 232 { 0xc800, 0x52, 236 }, { 0xcc00, 0x53, 241 }, { 0xd000, 0x54, 247 }, 233 { 0xd400, 0x55, 252 }, { 0xd800, 0x56, 258 }, { 0xdc00, 0x57, 263 }, 234 { 0xe000, 0x58, 269 }, { 0xe400, 0x59, 275 }, { 0xe800, 0x5a, 281 }, 235 { 0xec00, 0x5b, 287 }, { 0xf000, 0x5c, 293 }, { 0xf400, 0x5d, 300 }, 236 { 0xf800, 0x5e, 306 }, { 0xfc00, 0x5f, 313 }, { 0x0001, 0x60, 320 }, 237 { 0x0401, 0x61, 327 }, { 0x0801, 0x62, 334 }, { 0x0c01, 0x63, 341 }, 238 { 0x1001, 0x64, 349 }, { 0x1401, 0x65, 357 }, { 0x1801, 0x66, 364 }, 239 { 0x1c01, 0x67, 372 }, { 0x2001, 0x68, 381 }, { 0x2401, 0x69, 389 }, 240 { 0x2801, 0x6a, 397 }, { 0x2c01, 0x6b, 406 }, { 0x3001, 0x6c, 415 }, 241 { 0x3401, 0x6d, 424 }, { 0x3801, 0x6e, 433 }, { 0x3c01, 0x6f, 443 }, 242 { 0x4001, 0x70, 453 }, { 0x4401, 0x71, 462 }, { 0x4801, 0x72, 473 }, 243 { 0x4c01, 0x73, 483 }, { 0x5001, 0x74, 494 }, { 0x5401, 0x75, 504 }, 244 { 0x5801, 0x76, 515 }, { 0x5c01, 0x77, 527 }, { 0x6001, 0x78, 538 }, 245 { 0x6401, 0x79, 550 }, { 0x6801, 0x7a, 562 }, { 0x6c01, 0x7b, 574 }, 246 { 0x7001, 0x7c, 587 }, { 0x7401, 0x7d, 600 }, { 0x7801, 0x7e, 613 }, 247 { 0x7c01, 0x7f, 626 }, { 0x8001, 0x00, 640 }, { 0x8401, 0x00, 654 }, 248 { 0x8801, 0x00, 668 }, { 0x8c01, 0x00, 683 }, { 0x9001, 0x00, 698 }, 249 { 0x9401, 0x00, 713 }, { 0x9801, 0x00, 729 }, { 0x9c01, 0x00, 745 }, 250 { 0xa001, 0x00, 761 }, { 0xa401, 0x00, 778 }, { 0xa801, 0x00, 795 }, 251 { 0xac01, 0x00, 812 }, { 0xb001, 0x00, 830 }, { 0xb401, 0x00, 848 }, 252 { 0xb801, 0x00, 867 }, { 0xbc01, 0x00, 886 }, { 0xc001, 0x00, 905 }, 253 { 0xc401, 0x00, 925 }, { 0xc801, 0x00, 945 }, { 0xcc01, 0x00, 966 }, 254 { 0xd001, 0x00, 987 }, { 0xd401, 0x00, 1009 }, { 0xd801, 0x00, 1031 }, 255 { 0xdc01, 0x00, 1053 }, { 0xe001, 0x00, 1076 }, { 0xe401, 0x00, 1100 }, 256 { 0xe801, 0x00, 1124 }, { 0xec01, 0x00, 1149 }, { 0xf001, 0x00, 1174 }, 257 { 0xf401, 0x00, 1199 }, { 0xf801, 0x00, 1226 }, { 0xfc01, 0x00, 1253 } 258}; 259 260#define joycon_max_rumble_amp (1003) 261static const struct joycon_rumble_amp_data joycon_rumble_amplitudes[] = { 262 /* high, low, amp */ 263 { 0x00, 0x0040, 0 }, 264 { 0x02, 0x8040, 10 }, { 0x04, 0x0041, 12 }, { 0x06, 0x8041, 14 }, 265 { 0x08, 0x0042, 17 }, { 0x0a, 0x8042, 20 }, { 0x0c, 0x0043, 24 }, 266 { 0x0e, 0x8043, 28 }, { 0x10, 0x0044, 33 }, { 0x12, 0x8044, 40 }, 267 { 0x14, 0x0045, 47 }, { 0x16, 0x8045, 56 }, { 0x18, 0x0046, 67 }, 268 { 0x1a, 0x8046, 80 }, { 0x1c, 0x0047, 95 }, { 0x1e, 0x8047, 112 }, 269 { 0x20, 0x0048, 117 }, { 0x22, 0x8048, 123 }, { 0x24, 0x0049, 128 }, 270 { 0x26, 0x8049, 134 }, { 0x28, 0x004a, 140 }, { 0x2a, 0x804a, 146 }, 271 { 0x2c, 0x004b, 152 }, { 0x2e, 0x804b, 159 }, { 0x30, 0x004c, 166 }, 272 { 0x32, 0x804c, 173 }, { 0x34, 0x004d, 181 }, { 0x36, 0x804d, 189 }, 273 { 0x38, 0x004e, 198 }, { 0x3a, 0x804e, 206 }, { 0x3c, 0x004f, 215 }, 274 { 0x3e, 0x804f, 225 }, { 0x40, 0x0050, 230 }, { 0x42, 0x8050, 235 }, 275 { 0x44, 0x0051, 240 }, { 0x46, 0x8051, 245 }, { 0x48, 0x0052, 251 }, 276 { 0x4a, 0x8052, 256 }, { 0x4c, 0x0053, 262 }, { 0x4e, 0x8053, 268 }, 277 { 0x50, 0x0054, 273 }, { 0x52, 0x8054, 279 }, { 0x54, 0x0055, 286 }, 278 { 0x56, 0x8055, 292 }, { 0x58, 0x0056, 298 }, { 0x5a, 0x8056, 305 }, 279 { 0x5c, 0x0057, 311 }, { 0x5e, 0x8057, 318 }, { 0x60, 0x0058, 325 }, 280 { 0x62, 0x8058, 332 }, { 0x64, 0x0059, 340 }, { 0x66, 0x8059, 347 }, 281 { 0x68, 0x005a, 355 }, { 0x6a, 0x805a, 362 }, { 0x6c, 0x005b, 370 }, 282 { 0x6e, 0x805b, 378 }, { 0x70, 0x005c, 387 }, { 0x72, 0x805c, 395 }, 283 { 0x74, 0x005d, 404 }, { 0x76, 0x805d, 413 }, { 0x78, 0x005e, 422 }, 284 { 0x7a, 0x805e, 431 }, { 0x7c, 0x005f, 440 }, { 0x7e, 0x805f, 450 }, 285 { 0x80, 0x0060, 460 }, { 0x82, 0x8060, 470 }, { 0x84, 0x0061, 480 }, 286 { 0x86, 0x8061, 491 }, { 0x88, 0x0062, 501 }, { 0x8a, 0x8062, 512 }, 287 { 0x8c, 0x0063, 524 }, { 0x8e, 0x8063, 535 }, { 0x90, 0x0064, 547 }, 288 { 0x92, 0x8064, 559 }, { 0x94, 0x0065, 571 }, { 0x96, 0x8065, 584 }, 289 { 0x98, 0x0066, 596 }, { 0x9a, 0x8066, 609 }, { 0x9c, 0x0067, 623 }, 290 { 0x9e, 0x8067, 636 }, { 0xa0, 0x0068, 650 }, { 0xa2, 0x8068, 665 }, 291 { 0xa4, 0x0069, 679 }, { 0xa6, 0x8069, 694 }, { 0xa8, 0x006a, 709 }, 292 { 0xaa, 0x806a, 725 }, { 0xac, 0x006b, 741 }, { 0xae, 0x806b, 757 }, 293 { 0xb0, 0x006c, 773 }, { 0xb2, 0x806c, 790 }, { 0xb4, 0x006d, 808 }, 294 { 0xb6, 0x806d, 825 }, { 0xb8, 0x006e, 843 }, { 0xba, 0x806e, 862 }, 295 { 0xbc, 0x006f, 881 }, { 0xbe, 0x806f, 900 }, { 0xc0, 0x0070, 920 }, 296 { 0xc2, 0x8070, 940 }, { 0xc4, 0x0071, 960 }, { 0xc6, 0x8071, 981 }, 297 { 0xc8, 0x0072, joycon_max_rumble_amp } 298}; 299static const u16 JC_RUMBLE_DFLT_LOW_FREQ = 160; 300static const u16 JC_RUMBLE_DFLT_HIGH_FREQ = 320; 301static const unsigned short JC_RUMBLE_ZERO_AMP_PKT_CNT = 5; 302#endif /* IS_ENABLED(CONFIG_NINTENDO_FF) */ 303static const u16 JC_RUMBLE_PERIOD_MS = 50; 304 305/* States for controller state machine */ 306enum joycon_ctlr_state { 307 JOYCON_CTLR_STATE_INIT, 308 JOYCON_CTLR_STATE_READ, 309 JOYCON_CTLR_STATE_REMOVED, 310}; 311 312/* Controller type received as part of device info */ 313enum joycon_ctlr_type { 314 JOYCON_CTLR_TYPE_JCL = 0x01, 315 JOYCON_CTLR_TYPE_JCR = 0x02, 316 JOYCON_CTLR_TYPE_PRO = 0x03, 317 JOYCON_CTLR_TYPE_NESL = 0x09, 318 JOYCON_CTLR_TYPE_NESR = 0x0A, 319 JOYCON_CTLR_TYPE_SNES = 0x0B, 320 JOYCON_CTLR_TYPE_GEN = 0x0D, 321 JOYCON_CTLR_TYPE_N64 = 0x0C, 322}; 323 324struct joycon_stick_cal { 325 s32 max; 326 s32 min; 327 s32 center; 328}; 329 330struct joycon_imu_cal { 331 s16 offset[3]; 332 s16 scale[3]; 333}; 334 335/* 336 * All the controller's button values are stored in a u32. 337 * They can be accessed with bitwise ANDs. 338 */ 339#define JC_BTN_Y BIT(0) 340#define JC_BTN_X BIT(1) 341#define JC_BTN_B BIT(2) 342#define JC_BTN_A BIT(3) 343#define JC_BTN_SR_R BIT(4) 344#define JC_BTN_SL_R BIT(5) 345#define JC_BTN_R BIT(6) 346#define JC_BTN_ZR BIT(7) 347#define JC_BTN_MINUS BIT(8) 348#define JC_BTN_PLUS BIT(9) 349#define JC_BTN_RSTICK BIT(10) 350#define JC_BTN_LSTICK BIT(11) 351#define JC_BTN_HOME BIT(12) 352#define JC_BTN_CAP BIT(13) /* capture button */ 353#define JC_BTN_DOWN BIT(16) 354#define JC_BTN_UP BIT(17) 355#define JC_BTN_RIGHT BIT(18) 356#define JC_BTN_LEFT BIT(19) 357#define JC_BTN_SR_L BIT(20) 358#define JC_BTN_SL_L BIT(21) 359#define JC_BTN_L BIT(22) 360#define JC_BTN_ZL BIT(23) 361 362struct joycon_ctlr_button_mapping { 363 u32 code; 364 u32 bit; 365}; 366 367/* 368 * D-pad is configured as buttons for the left Joy-Con only! 369 */ 370static const struct joycon_ctlr_button_mapping left_joycon_button_mappings[] = { 371 { BTN_TL, JC_BTN_L, }, 372 { BTN_TL2, JC_BTN_ZL, }, 373 { BTN_SELECT, JC_BTN_MINUS, }, 374 { BTN_THUMBL, JC_BTN_LSTICK, }, 375 { BTN_DPAD_UP, JC_BTN_UP, }, 376 { BTN_DPAD_DOWN, JC_BTN_DOWN, }, 377 { BTN_DPAD_LEFT, JC_BTN_LEFT, }, 378 { BTN_DPAD_RIGHT, JC_BTN_RIGHT, }, 379 { BTN_Z, JC_BTN_CAP, }, 380 { /* sentinel */ }, 381}; 382 383/* 384 * The unused *right*-side triggers become the SL/SR triggers for the *left* 385 * Joy-Con, if and only if we're not using a charging grip. 386 */ 387static const struct joycon_ctlr_button_mapping left_joycon_s_button_mappings[] = { 388 { BTN_TR, JC_BTN_SL_L, }, 389 { BTN_TR2, JC_BTN_SR_L, }, 390 { /* sentinel */ }, 391}; 392 393static const struct joycon_ctlr_button_mapping right_joycon_button_mappings[] = { 394 { BTN_EAST, JC_BTN_A, }, 395 { BTN_SOUTH, JC_BTN_B, }, 396 { BTN_NORTH, JC_BTN_X, }, 397 { BTN_WEST, JC_BTN_Y, }, 398 { BTN_TR, JC_BTN_R, }, 399 { BTN_TR2, JC_BTN_ZR, }, 400 { BTN_START, JC_BTN_PLUS, }, 401 { BTN_THUMBR, JC_BTN_RSTICK, }, 402 { BTN_MODE, JC_BTN_HOME, }, 403 { /* sentinel */ }, 404}; 405 406/* 407 * The unused *left*-side triggers become the SL/SR triggers for the *right* 408 * Joy-Con, if and only if we're not using a charging grip. 409 */ 410static const struct joycon_ctlr_button_mapping right_joycon_s_button_mappings[] = { 411 { BTN_TL, JC_BTN_SL_R, }, 412 { BTN_TL2, JC_BTN_SR_R, }, 413 { /* sentinel */ }, 414}; 415 416static const struct joycon_ctlr_button_mapping procon_button_mappings[] = { 417 { BTN_EAST, JC_BTN_A, }, 418 { BTN_SOUTH, JC_BTN_B, }, 419 { BTN_NORTH, JC_BTN_X, }, 420 { BTN_WEST, JC_BTN_Y, }, 421 { BTN_TL, JC_BTN_L, }, 422 { BTN_TR, JC_BTN_R, }, 423 { BTN_TL2, JC_BTN_ZL, }, 424 { BTN_TR2, JC_BTN_ZR, }, 425 { BTN_SELECT, JC_BTN_MINUS, }, 426 { BTN_START, JC_BTN_PLUS, }, 427 { BTN_THUMBL, JC_BTN_LSTICK, }, 428 { BTN_THUMBR, JC_BTN_RSTICK, }, 429 { BTN_MODE, JC_BTN_HOME, }, 430 { BTN_Z, JC_BTN_CAP, }, 431 { /* sentinel */ }, 432}; 433 434static const struct joycon_ctlr_button_mapping nescon_button_mappings[] = { 435 { BTN_SOUTH, JC_BTN_A, }, 436 { BTN_EAST, JC_BTN_B, }, 437 { BTN_TL, JC_BTN_L, }, 438 { BTN_TR, JC_BTN_R, }, 439 { BTN_SELECT, JC_BTN_MINUS, }, 440 { BTN_START, JC_BTN_PLUS, }, 441 { /* sentinel */ }, 442}; 443 444static const struct joycon_ctlr_button_mapping snescon_button_mappings[] = { 445 { BTN_EAST, JC_BTN_A, }, 446 { BTN_SOUTH, JC_BTN_B, }, 447 { BTN_NORTH, JC_BTN_X, }, 448 { BTN_WEST, JC_BTN_Y, }, 449 { BTN_TL, JC_BTN_L, }, 450 { BTN_TR, JC_BTN_R, }, 451 { BTN_TL2, JC_BTN_ZL, }, 452 { BTN_TR2, JC_BTN_ZR, }, 453 { BTN_SELECT, JC_BTN_MINUS, }, 454 { BTN_START, JC_BTN_PLUS, }, 455 { /* sentinel */ }, 456}; 457 458/* 459 * "A", "B", and "C" are mapped positionally, rather than by label (e.g., "A" 460 * gets assigned to BTN_EAST instead of BTN_A). 461 */ 462static const struct joycon_ctlr_button_mapping gencon_button_mappings[] = { 463 { BTN_SOUTH, JC_BTN_A, }, 464 { BTN_EAST, JC_BTN_B, }, 465 { BTN_WEST, JC_BTN_R, }, 466 { BTN_SELECT, JC_BTN_ZR, }, 467 { BTN_START, JC_BTN_PLUS, }, 468 { BTN_MODE, JC_BTN_HOME, }, 469 { BTN_Z, JC_BTN_CAP, }, 470 { /* sentinel */ }, 471}; 472 473/* 474 * N64's C buttons get assigned to d-pad directions and registered as buttons. 475 */ 476static const struct joycon_ctlr_button_mapping n64con_button_mappings[] = { 477 { BTN_A, JC_BTN_A, }, 478 { BTN_B, JC_BTN_B, }, 479 { BTN_TL2, JC_BTN_ZL, }, /* Z */ 480 { BTN_TL, JC_BTN_L, }, 481 { BTN_TR, JC_BTN_R, }, 482 { BTN_TR2, JC_BTN_LSTICK, }, /* ZR */ 483 { BTN_START, JC_BTN_PLUS, }, 484 { BTN_FORWARD, JC_BTN_Y, }, /* C UP */ 485 { BTN_BACK, JC_BTN_ZR, }, /* C DOWN */ 486 { BTN_LEFT, JC_BTN_X, }, /* C LEFT */ 487 { BTN_RIGHT, JC_BTN_MINUS, }, /* C RIGHT */ 488 { BTN_MODE, JC_BTN_HOME, }, 489 { BTN_Z, JC_BTN_CAP, }, 490 { /* sentinel */ }, 491}; 492 493enum joycon_msg_type { 494 JOYCON_MSG_TYPE_NONE, 495 JOYCON_MSG_TYPE_USB, 496 JOYCON_MSG_TYPE_SUBCMD, 497}; 498 499struct joycon_rumble_output { 500 u8 output_id; 501 u8 packet_num; 502 u8 rumble_data[8]; 503} __packed; 504 505struct joycon_subcmd_request { 506 u8 output_id; /* must be 0x01 for subcommand, 0x10 for rumble only */ 507 u8 packet_num; /* incremented every send */ 508 u8 rumble_data[8]; 509 u8 subcmd_id; 510 u8 data[]; /* length depends on the subcommand */ 511} __packed; 512 513struct joycon_subcmd_reply { 514 u8 ack; /* MSB 1 for ACK, 0 for NACK */ 515 u8 id; /* id of requested subcmd */ 516 u8 data[]; /* will be at most 35 bytes */ 517} __packed; 518 519struct joycon_imu_data { 520 s16 accel_x; 521 s16 accel_y; 522 s16 accel_z; 523 s16 gyro_x; 524 s16 gyro_y; 525 s16 gyro_z; 526} __packed; 527 528struct joycon_input_report { 529 u8 id; 530 u8 timer; 531 u8 bat_con; /* battery and connection info */ 532 u8 button_status[3]; 533 u8 left_stick[3]; 534 u8 right_stick[3]; 535 u8 vibrator_report; 536 537 union { 538 struct joycon_subcmd_reply subcmd_reply; 539 /* IMU input reports contain 3 samples */ 540 u8 imu_raw_bytes[sizeof(struct joycon_imu_data) * 3]; 541 }; 542} __packed; 543 544#define JC_MAX_RESP_SIZE (sizeof(struct joycon_input_report) + 35) 545#define JC_RUMBLE_DATA_SIZE 8 546#define JC_RUMBLE_QUEUE_SIZE 8 547 548static const char * const joycon_player_led_names[] = { 549 LED_FUNCTION_PLAYER1, 550 LED_FUNCTION_PLAYER2, 551 LED_FUNCTION_PLAYER3, 552 LED_FUNCTION_PLAYER4, 553}; 554#define JC_NUM_LEDS ARRAY_SIZE(joycon_player_led_names) 555#define JC_NUM_LED_PATTERNS 8 556/* Taken from https://www.nintendo.com/my/support/qa/detail/33822 */ 557static const enum led_brightness joycon_player_led_patterns[JC_NUM_LED_PATTERNS][JC_NUM_LEDS] = { 558 { 1, 0, 0, 0 }, 559 { 1, 1, 0, 0 }, 560 { 1, 1, 1, 0 }, 561 { 1, 1, 1, 1 }, 562 { 1, 0, 0, 1 }, 563 { 1, 0, 1, 0 }, 564 { 1, 0, 1, 1 }, 565 { 0, 1, 1, 0 }, 566}; 567 568/* Each physical controller is associated with a joycon_ctlr struct */ 569struct joycon_ctlr { 570 struct hid_device *hdev; 571 struct input_dev *input; 572 struct led_classdev leds[JC_NUM_LEDS]; /* player leds */ 573 struct led_classdev home_led; 574 enum joycon_ctlr_state ctlr_state; 575 spinlock_t lock; 576 u8 mac_addr[6]; 577 char *mac_addr_str; 578 enum joycon_ctlr_type ctlr_type; 579 580 /* The following members are used for synchronous sends/receives */ 581 enum joycon_msg_type msg_type; 582 u8 subcmd_num; 583 struct mutex output_mutex; 584 u8 input_buf[JC_MAX_RESP_SIZE]; 585 wait_queue_head_t wait; 586 bool received_resp; 587 u8 usb_ack_match; 588 u8 subcmd_ack_match; 589 bool received_input_report; 590 unsigned int last_input_report_msecs; 591 unsigned int last_subcmd_sent_msecs; 592 unsigned int consecutive_valid_report_deltas; 593 594 /* factory calibration data */ 595 struct joycon_stick_cal left_stick_cal_x; 596 struct joycon_stick_cal left_stick_cal_y; 597 struct joycon_stick_cal right_stick_cal_x; 598 struct joycon_stick_cal right_stick_cal_y; 599 600 struct joycon_imu_cal accel_cal; 601 struct joycon_imu_cal gyro_cal; 602 603 /* prevents needlessly recalculating these divisors every sample */ 604 s32 imu_cal_accel_divisor[3]; 605 s32 imu_cal_gyro_divisor[3]; 606 607 /* power supply data */ 608 struct power_supply *battery; 609 struct power_supply_desc battery_desc; 610 u8 battery_capacity; 611 bool battery_charging; 612 bool host_powered; 613 614 /* rumble */ 615 u8 rumble_data[JC_RUMBLE_QUEUE_SIZE][JC_RUMBLE_DATA_SIZE]; 616 int rumble_queue_head; 617 int rumble_queue_tail; 618 struct workqueue_struct *rumble_queue; 619 struct work_struct rumble_worker; 620 unsigned int rumble_msecs; 621 u16 rumble_ll_freq; 622 u16 rumble_lh_freq; 623 u16 rumble_rl_freq; 624 u16 rumble_rh_freq; 625 unsigned short rumble_zero_countdown; 626 627 /* imu */ 628 struct input_dev *imu_input; 629 bool imu_first_packet_received; /* helps in initiating timestamp */ 630 unsigned int imu_timestamp_us; /* timestamp we report to userspace */ 631 unsigned int imu_last_pkt_ms; /* used to calc imu report delta */ 632 /* the following are used to track the average imu report time delta */ 633 unsigned int imu_delta_samples_count; 634 unsigned int imu_delta_samples_sum; 635 unsigned int imu_avg_delta_ms; 636}; 637 638/* Helper macros for checking controller type */ 639#define jc_type_is_joycon(ctlr) \ 640 (ctlr->hdev->product == USB_DEVICE_ID_NINTENDO_JOYCONL || \ 641 ctlr->hdev->product == USB_DEVICE_ID_NINTENDO_JOYCONR || \ 642 ctlr->hdev->product == USB_DEVICE_ID_NINTENDO_CHRGGRIP) 643#define jc_type_is_procon(ctlr) \ 644 (ctlr->hdev->product == USB_DEVICE_ID_NINTENDO_PROCON) 645#define jc_type_is_chrggrip(ctlr) \ 646 (ctlr->hdev->product == USB_DEVICE_ID_NINTENDO_CHRGGRIP) 647 648/* Does this controller have inputs associated with left joycon? */ 649#define jc_type_has_left(ctlr) \ 650 (ctlr->ctlr_type == JOYCON_CTLR_TYPE_JCL || \ 651 ctlr->ctlr_type == JOYCON_CTLR_TYPE_PRO || \ 652 ctlr->ctlr_type == JOYCON_CTLR_TYPE_N64) 653 654/* Does this controller have inputs associated with right joycon? */ 655#define jc_type_has_right(ctlr) \ 656 (ctlr->ctlr_type == JOYCON_CTLR_TYPE_JCR || \ 657 ctlr->ctlr_type == JOYCON_CTLR_TYPE_PRO) 658 659 660/* 661 * Controller device helpers 662 * 663 * These look at the device ID known to the HID subsystem to identify a device, 664 * but take caution: some NSO devices lie about themselves (NES Joy-Cons and 665 * Sega Genesis controller). See type helpers below. 666 * 667 * These helpers are most useful early during the HID probe or in conjunction 668 * with the capability helpers below. 669 */ 670static inline bool joycon_device_is_procon(struct joycon_ctlr *ctlr) 671{ 672 return ctlr->hdev->product == USB_DEVICE_ID_NINTENDO_PROCON; 673} 674 675static inline bool joycon_device_is_chrggrip(struct joycon_ctlr *ctlr) 676{ 677 return ctlr->hdev->product == USB_DEVICE_ID_NINTENDO_CHRGGRIP; 678} 679 680static inline bool joycon_device_is_snescon(struct joycon_ctlr *ctlr) 681{ 682 return ctlr->hdev->product == USB_DEVICE_ID_NINTENDO_SNESCON; 683} 684 685static inline bool joycon_device_is_gencon(struct joycon_ctlr *ctlr) 686{ 687 return ctlr->hdev->product == USB_DEVICE_ID_NINTENDO_GENCON; 688} 689 690static inline bool joycon_device_is_n64con(struct joycon_ctlr *ctlr) 691{ 692 return ctlr->hdev->product == USB_DEVICE_ID_NINTENDO_N64CON; 693} 694 695static inline bool joycon_device_has_usb(struct joycon_ctlr *ctlr) 696{ 697 return joycon_device_is_procon(ctlr) || 698 joycon_device_is_chrggrip(ctlr) || 699 joycon_device_is_snescon(ctlr) || 700 joycon_device_is_gencon(ctlr) || 701 joycon_device_is_n64con(ctlr); 702} 703 704/* 705 * Controller type helpers 706 * 707 * These are slightly different than the device-ID-based helpers above. They are 708 * generally more reliable, since they can distinguish between, e.g., Genesis 709 * versus SNES, or NES Joy-Cons versus regular Switch Joy-Cons. They're most 710 * useful for reporting available inputs. For other kinds of distinctions, see 711 * the capability helpers below. 712 * 713 * They have two major drawbacks: (1) they're not available until after we set 714 * the reporting method and then request the device info; (2) they can't 715 * distinguish all controllers (like the Charging Grip from the Pro controller.) 716 */ 717static inline bool joycon_type_is_left_joycon(struct joycon_ctlr *ctlr) 718{ 719 return ctlr->ctlr_type == JOYCON_CTLR_TYPE_JCL; 720} 721 722static inline bool joycon_type_is_right_joycon(struct joycon_ctlr *ctlr) 723{ 724 return ctlr->ctlr_type == JOYCON_CTLR_TYPE_JCR; 725} 726 727static inline bool joycon_type_is_procon(struct joycon_ctlr *ctlr) 728{ 729 return ctlr->ctlr_type == JOYCON_CTLR_TYPE_PRO; 730} 731 732static inline bool joycon_type_is_snescon(struct joycon_ctlr *ctlr) 733{ 734 return ctlr->ctlr_type == JOYCON_CTLR_TYPE_SNES; 735} 736 737static inline bool joycon_type_is_gencon(struct joycon_ctlr *ctlr) 738{ 739 return ctlr->ctlr_type == JOYCON_CTLR_TYPE_GEN; 740} 741 742static inline bool joycon_type_is_n64con(struct joycon_ctlr *ctlr) 743{ 744 return ctlr->ctlr_type == JOYCON_CTLR_TYPE_N64; 745} 746 747static inline bool joycon_type_is_left_nescon(struct joycon_ctlr *ctlr) 748{ 749 return ctlr->ctlr_type == JOYCON_CTLR_TYPE_NESL; 750} 751 752static inline bool joycon_type_is_right_nescon(struct joycon_ctlr *ctlr) 753{ 754 return ctlr->ctlr_type == JOYCON_CTLR_TYPE_NESR; 755} 756 757static inline bool joycon_type_is_any_joycon(struct joycon_ctlr *ctlr) 758{ 759 return joycon_type_is_left_joycon(ctlr) || 760 joycon_type_is_right_joycon(ctlr) || 761 joycon_device_is_chrggrip(ctlr); 762} 763 764static inline bool joycon_type_is_any_nescon(struct joycon_ctlr *ctlr) 765{ 766 return joycon_type_is_left_nescon(ctlr) || 767 joycon_type_is_right_nescon(ctlr); 768} 769 770/* 771 * Controller capability helpers 772 * 773 * These helpers combine the use of the helpers above to detect certain 774 * capabilities during initialization. They are always accurate but (since they 775 * use type helpers) cannot be used early in the HID probe. 776 */ 777static inline bool joycon_has_imu(struct joycon_ctlr *ctlr) 778{ 779 return joycon_device_is_chrggrip(ctlr) || 780 joycon_type_is_any_joycon(ctlr) || 781 joycon_type_is_procon(ctlr); 782} 783 784static inline bool joycon_has_joysticks(struct joycon_ctlr *ctlr) 785{ 786 return joycon_device_is_chrggrip(ctlr) || 787 joycon_type_is_any_joycon(ctlr) || 788 joycon_type_is_procon(ctlr) || 789 joycon_type_is_n64con(ctlr); 790} 791 792static inline bool joycon_has_rumble(struct joycon_ctlr *ctlr) 793{ 794 return joycon_device_is_chrggrip(ctlr) || 795 joycon_type_is_any_joycon(ctlr) || 796 joycon_type_is_procon(ctlr) || 797 joycon_type_is_n64con(ctlr); 798} 799 800static inline bool joycon_using_usb(struct joycon_ctlr *ctlr) 801{ 802 return ctlr->hdev->bus == BUS_USB; 803} 804 805static int __joycon_hid_send(struct hid_device *hdev, u8 *data, size_t len) 806{ 807 u8 *buf; 808 int ret; 809 810 buf = kmemdup(data, len, GFP_KERNEL); 811 if (!buf) 812 return -ENOMEM; 813 ret = hid_hw_output_report(hdev, buf, len); 814 kfree(buf); 815 if (ret < 0) 816 hid_dbg(hdev, "Failed to send output report ret=%d\n", ret); 817 return ret; 818} 819 820static void joycon_wait_for_input_report(struct joycon_ctlr *ctlr) 821{ 822 int ret; 823 824 /* 825 * If we are in the proper reporting mode, wait for an input 826 * report prior to sending the subcommand. This improves 827 * reliability considerably. 828 */ 829 if (ctlr->ctlr_state == JOYCON_CTLR_STATE_READ) { 830 unsigned long flags; 831 832 spin_lock_irqsave(&ctlr->lock, flags); 833 ctlr->received_input_report = false; 834 spin_unlock_irqrestore(&ctlr->lock, flags); 835 ret = wait_event_timeout(ctlr->wait, 836 ctlr->received_input_report, 837 HZ / 4); 838 /* We will still proceed, even with a timeout here */ 839 if (!ret) 840 hid_warn(ctlr->hdev, 841 "timeout waiting for input report\n"); 842 } 843} 844 845/* 846 * Sending subcommands and/or rumble data at too high a rate can cause bluetooth 847 * controller disconnections. 848 */ 849#define JC_INPUT_REPORT_MIN_DELTA 8 850#define JC_INPUT_REPORT_MAX_DELTA 17 851#define JC_SUBCMD_TX_OFFSET_MS 4 852#define JC_SUBCMD_VALID_DELTA_REQ 3 853#define JC_SUBCMD_RATE_MAX_ATTEMPTS 500 854#define JC_SUBCMD_RATE_LIMITER_USB_MS 20 855#define JC_SUBCMD_RATE_LIMITER_BT_MS 60 856#define JC_SUBCMD_RATE_LIMITER_MS(ctlr) ((ctlr)->hdev->bus == BUS_USB ? JC_SUBCMD_RATE_LIMITER_USB_MS : JC_SUBCMD_RATE_LIMITER_BT_MS) 857static void joycon_enforce_subcmd_rate(struct joycon_ctlr *ctlr) 858{ 859 unsigned int current_ms; 860 unsigned long subcmd_delta; 861 int consecutive_valid_deltas = 0; 862 int attempts = 0; 863 unsigned long flags; 864 865 if (unlikely(ctlr->ctlr_state != JOYCON_CTLR_STATE_READ)) 866 return; 867 868 do { 869 joycon_wait_for_input_report(ctlr); 870 current_ms = jiffies_to_msecs(jiffies); 871 subcmd_delta = current_ms - ctlr->last_subcmd_sent_msecs; 872 873 spin_lock_irqsave(&ctlr->lock, flags); 874 consecutive_valid_deltas = ctlr->consecutive_valid_report_deltas; 875 spin_unlock_irqrestore(&ctlr->lock, flags); 876 877 attempts++; 878 } while ((consecutive_valid_deltas < JC_SUBCMD_VALID_DELTA_REQ || 879 subcmd_delta < JC_SUBCMD_RATE_LIMITER_MS(ctlr)) && 880 ctlr->ctlr_state == JOYCON_CTLR_STATE_READ && 881 attempts < JC_SUBCMD_RATE_MAX_ATTEMPTS); 882 883 if (attempts >= JC_SUBCMD_RATE_MAX_ATTEMPTS) { 884 hid_warn(ctlr->hdev, "%s: exceeded max attempts", __func__); 885 return; 886 } 887 888 ctlr->last_subcmd_sent_msecs = current_ms; 889 890 /* 891 * Wait a short time after receiving an input report before 892 * transmitting. This should reduce odds of a TX coinciding with an RX. 893 * Minimizing concurrent BT traffic with the controller seems to lower 894 * the rate of disconnections. 895 */ 896 msleep(JC_SUBCMD_TX_OFFSET_MS); 897} 898 899static int joycon_hid_send_sync(struct joycon_ctlr *ctlr, u8 *data, size_t len, 900 u32 timeout) 901{ 902 int ret; 903 int tries = 2; 904 905 /* 906 * The controller occasionally seems to drop subcommands. In testing, 907 * doing one retry after a timeout appears to always work. 908 */ 909 while (tries--) { 910 joycon_enforce_subcmd_rate(ctlr); 911 912 ret = __joycon_hid_send(ctlr->hdev, data, len); 913 if (ret < 0) { 914 memset(ctlr->input_buf, 0, JC_MAX_RESP_SIZE); 915 return ret; 916 } 917 918 ret = wait_event_timeout(ctlr->wait, ctlr->received_resp, 919 timeout); 920 if (!ret) { 921 hid_dbg(ctlr->hdev, 922 "synchronous send/receive timed out\n"); 923 if (tries) { 924 hid_dbg(ctlr->hdev, 925 "retrying sync send after timeout\n"); 926 } 927 memset(ctlr->input_buf, 0, JC_MAX_RESP_SIZE); 928 ret = -ETIMEDOUT; 929 } else { 930 ret = 0; 931 break; 932 } 933 } 934 935 ctlr->received_resp = false; 936 return ret; 937} 938 939static int joycon_send_usb(struct joycon_ctlr *ctlr, u8 cmd, u32 timeout) 940{ 941 int ret; 942 u8 buf[2] = {JC_OUTPUT_USB_CMD}; 943 944 buf[1] = cmd; 945 ctlr->usb_ack_match = cmd; 946 ctlr->msg_type = JOYCON_MSG_TYPE_USB; 947 ret = joycon_hid_send_sync(ctlr, buf, sizeof(buf), timeout); 948 if (ret) 949 hid_dbg(ctlr->hdev, "send usb command failed; ret=%d\n", ret); 950 return ret; 951} 952 953static int joycon_send_subcmd(struct joycon_ctlr *ctlr, 954 struct joycon_subcmd_request *subcmd, 955 size_t data_len, u32 timeout) 956{ 957 int ret; 958 unsigned long flags; 959 960 spin_lock_irqsave(&ctlr->lock, flags); 961 /* 962 * If the controller has been removed, just return ENODEV so the LED 963 * subsystem doesn't print invalid errors on removal. 964 */ 965 if (ctlr->ctlr_state == JOYCON_CTLR_STATE_REMOVED) { 966 spin_unlock_irqrestore(&ctlr->lock, flags); 967 return -ENODEV; 968 } 969 memcpy(subcmd->rumble_data, ctlr->rumble_data[ctlr->rumble_queue_tail], 970 JC_RUMBLE_DATA_SIZE); 971 spin_unlock_irqrestore(&ctlr->lock, flags); 972 973 subcmd->output_id = JC_OUTPUT_RUMBLE_AND_SUBCMD; 974 subcmd->packet_num = ctlr->subcmd_num; 975 if (++ctlr->subcmd_num > 0xF) 976 ctlr->subcmd_num = 0; 977 ctlr->subcmd_ack_match = subcmd->subcmd_id; 978 ctlr->msg_type = JOYCON_MSG_TYPE_SUBCMD; 979 980 ret = joycon_hid_send_sync(ctlr, (u8 *)subcmd, 981 sizeof(*subcmd) + data_len, timeout); 982 if (ret < 0) 983 hid_dbg(ctlr->hdev, "send subcommand failed; ret=%d\n", ret); 984 else 985 ret = 0; 986 return ret; 987} 988 989/* Supply nibbles for flash and on. Ones correspond to active */ 990static int joycon_set_player_leds(struct joycon_ctlr *ctlr, u8 flash, u8 on) 991{ 992 struct joycon_subcmd_request *req; 993 u8 buffer[sizeof(*req) + 1] = { 0 }; 994 995 req = (struct joycon_subcmd_request *)buffer; 996 req->subcmd_id = JC_SUBCMD_SET_PLAYER_LIGHTS; 997 req->data[0] = (flash << 4) | on; 998 999 hid_dbg(ctlr->hdev, "setting player leds\n"); 1000 return joycon_send_subcmd(ctlr, req, 1, HZ/4); 1001} 1002 1003static int joycon_set_home_led(struct joycon_ctlr *ctlr, enum led_brightness brightness) 1004{ 1005 struct joycon_subcmd_request *req; 1006 u8 buffer[sizeof(*req) + 5] = { 0 }; 1007 u8 *data; 1008 1009 req = (struct joycon_subcmd_request *)buffer; 1010 req->subcmd_id = JC_SUBCMD_SET_HOME_LIGHT; 1011 data = req->data; 1012 data[0] = 0x01; 1013 data[1] = brightness << 4; 1014 data[2] = brightness | (brightness << 4); 1015 data[3] = 0x11; 1016 data[4] = 0x11; 1017 1018 hid_dbg(ctlr->hdev, "setting home led brightness\n"); 1019 return joycon_send_subcmd(ctlr, req, 5, HZ/4); 1020} 1021 1022static int joycon_request_spi_flash_read(struct joycon_ctlr *ctlr, 1023 u32 start_addr, u8 size, u8 **reply) 1024{ 1025 struct joycon_subcmd_request *req; 1026 struct joycon_input_report *report; 1027 u8 buffer[sizeof(*req) + 5] = { 0 }; 1028 u8 *data; 1029 int ret; 1030 1031 if (!reply) 1032 return -EINVAL; 1033 1034 req = (struct joycon_subcmd_request *)buffer; 1035 req->subcmd_id = JC_SUBCMD_SPI_FLASH_READ; 1036 data = req->data; 1037 put_unaligned_le32(start_addr, data); 1038 data[4] = size; 1039 1040 hid_dbg(ctlr->hdev, "requesting SPI flash data\n"); 1041 ret = joycon_send_subcmd(ctlr, req, 5, HZ); 1042 if (ret) { 1043 hid_err(ctlr->hdev, "failed reading SPI flash; ret=%d\n", ret); 1044 } else { 1045 report = (struct joycon_input_report *)ctlr->input_buf; 1046 /* The read data starts at the 6th byte */ 1047 *reply = &report->subcmd_reply.data[5]; 1048 } 1049 return ret; 1050} 1051 1052/* 1053 * User calibration's presence is denoted with a magic byte preceding it. 1054 * returns 0 if magic val is present, 1 if not present, < 0 on error 1055 */ 1056static int joycon_check_for_cal_magic(struct joycon_ctlr *ctlr, u32 flash_addr) 1057{ 1058 int ret; 1059 u8 *reply; 1060 1061 ret = joycon_request_spi_flash_read(ctlr, flash_addr, 1062 JC_CAL_USR_MAGIC_SIZE, &reply); 1063 if (ret) 1064 return ret; 1065 1066 return reply[0] != JC_CAL_USR_MAGIC_0 || reply[1] != JC_CAL_USR_MAGIC_1; 1067} 1068 1069static int joycon_read_stick_calibration(struct joycon_ctlr *ctlr, u16 cal_addr, 1070 struct joycon_stick_cal *cal_x, 1071 struct joycon_stick_cal *cal_y, 1072 bool left_stick) 1073{ 1074 s32 x_max_above; 1075 s32 x_min_below; 1076 s32 y_max_above; 1077 s32 y_min_below; 1078 u8 *raw_cal; 1079 int ret; 1080 1081 ret = joycon_request_spi_flash_read(ctlr, cal_addr, 1082 JC_CAL_STICK_DATA_SIZE, &raw_cal); 1083 if (ret) 1084 return ret; 1085 1086 /* stick calibration parsing: note the order differs based on stick */ 1087 if (left_stick) { 1088 x_max_above = hid_field_extract(ctlr->hdev, (raw_cal + 0), 0, 1089 12); 1090 y_max_above = hid_field_extract(ctlr->hdev, (raw_cal + 1), 4, 1091 12); 1092 cal_x->center = hid_field_extract(ctlr->hdev, (raw_cal + 3), 0, 1093 12); 1094 cal_y->center = hid_field_extract(ctlr->hdev, (raw_cal + 4), 4, 1095 12); 1096 x_min_below = hid_field_extract(ctlr->hdev, (raw_cal + 6), 0, 1097 12); 1098 y_min_below = hid_field_extract(ctlr->hdev, (raw_cal + 7), 4, 1099 12); 1100 } else { 1101 cal_x->center = hid_field_extract(ctlr->hdev, (raw_cal + 0), 0, 1102 12); 1103 cal_y->center = hid_field_extract(ctlr->hdev, (raw_cal + 1), 4, 1104 12); 1105 x_min_below = hid_field_extract(ctlr->hdev, (raw_cal + 3), 0, 1106 12); 1107 y_min_below = hid_field_extract(ctlr->hdev, (raw_cal + 4), 4, 1108 12); 1109 x_max_above = hid_field_extract(ctlr->hdev, (raw_cal + 6), 0, 1110 12); 1111 y_max_above = hid_field_extract(ctlr->hdev, (raw_cal + 7), 4, 1112 12); 1113 } 1114 1115 cal_x->max = cal_x->center + x_max_above; 1116 cal_x->min = cal_x->center - x_min_below; 1117 cal_y->max = cal_y->center + y_max_above; 1118 cal_y->min = cal_y->center - y_min_below; 1119 1120 /* check if calibration values are plausible */ 1121 if (cal_x->min >= cal_x->center || cal_x->center >= cal_x->max || 1122 cal_y->min >= cal_y->center || cal_y->center >= cal_y->max) 1123 ret = -EINVAL; 1124 1125 return ret; 1126} 1127 1128static const u16 DFLT_STICK_CAL_CEN = 2000; 1129static const u16 DFLT_STICK_CAL_MAX = 3500; 1130static const u16 DFLT_STICK_CAL_MIN = 500; 1131static void joycon_use_default_calibration(struct hid_device *hdev, 1132 struct joycon_stick_cal *cal_x, 1133 struct joycon_stick_cal *cal_y, 1134 const char *stick, int ret) 1135{ 1136 hid_warn(hdev, 1137 "Failed to read %s stick cal, using defaults; e=%d\n", 1138 stick, ret); 1139 1140 cal_x->center = cal_y->center = DFLT_STICK_CAL_CEN; 1141 cal_x->max = cal_y->max = DFLT_STICK_CAL_MAX; 1142 cal_x->min = cal_y->min = DFLT_STICK_CAL_MIN; 1143} 1144 1145static int joycon_request_calibration(struct joycon_ctlr *ctlr) 1146{ 1147 u16 left_stick_addr = JC_CAL_FCT_DATA_LEFT_ADDR; 1148 u16 right_stick_addr = JC_CAL_FCT_DATA_RIGHT_ADDR; 1149 int ret; 1150 1151 hid_dbg(ctlr->hdev, "requesting cal data\n"); 1152 1153 /* check if user stick calibrations are present */ 1154 if (!joycon_check_for_cal_magic(ctlr, JC_CAL_USR_LEFT_MAGIC_ADDR)) { 1155 left_stick_addr = JC_CAL_USR_LEFT_DATA_ADDR; 1156 hid_info(ctlr->hdev, "using user cal for left stick\n"); 1157 } else { 1158 hid_info(ctlr->hdev, "using factory cal for left stick\n"); 1159 } 1160 if (!joycon_check_for_cal_magic(ctlr, JC_CAL_USR_RIGHT_MAGIC_ADDR)) { 1161 right_stick_addr = JC_CAL_USR_RIGHT_DATA_ADDR; 1162 hid_info(ctlr->hdev, "using user cal for right stick\n"); 1163 } else { 1164 hid_info(ctlr->hdev, "using factory cal for right stick\n"); 1165 } 1166 1167 /* read the left stick calibration data */ 1168 ret = joycon_read_stick_calibration(ctlr, left_stick_addr, 1169 &ctlr->left_stick_cal_x, 1170 &ctlr->left_stick_cal_y, 1171 true); 1172 1173 if (ret) 1174 joycon_use_default_calibration(ctlr->hdev, 1175 &ctlr->left_stick_cal_x, 1176 &ctlr->left_stick_cal_y, 1177 "left", ret); 1178 1179 /* read the right stick calibration data */ 1180 ret = joycon_read_stick_calibration(ctlr, right_stick_addr, 1181 &ctlr->right_stick_cal_x, 1182 &ctlr->right_stick_cal_y, 1183 false); 1184 1185 if (ret) 1186 joycon_use_default_calibration(ctlr->hdev, 1187 &ctlr->right_stick_cal_x, 1188 &ctlr->right_stick_cal_y, 1189 "right", ret); 1190 1191 hid_dbg(ctlr->hdev, "calibration:\n" 1192 "l_x_c=%d l_x_max=%d l_x_min=%d\n" 1193 "l_y_c=%d l_y_max=%d l_y_min=%d\n" 1194 "r_x_c=%d r_x_max=%d r_x_min=%d\n" 1195 "r_y_c=%d r_y_max=%d r_y_min=%d\n", 1196 ctlr->left_stick_cal_x.center, 1197 ctlr->left_stick_cal_x.max, 1198 ctlr->left_stick_cal_x.min, 1199 ctlr->left_stick_cal_y.center, 1200 ctlr->left_stick_cal_y.max, 1201 ctlr->left_stick_cal_y.min, 1202 ctlr->right_stick_cal_x.center, 1203 ctlr->right_stick_cal_x.max, 1204 ctlr->right_stick_cal_x.min, 1205 ctlr->right_stick_cal_y.center, 1206 ctlr->right_stick_cal_y.max, 1207 ctlr->right_stick_cal_y.min); 1208 1209 return 0; 1210} 1211 1212/* 1213 * These divisors are calculated once rather than for each sample. They are only 1214 * dependent on the IMU calibration values. They are used when processing the 1215 * IMU input reports. 1216 */ 1217static void joycon_calc_imu_cal_divisors(struct joycon_ctlr *ctlr) 1218{ 1219 int i, divz = 0; 1220 1221 for (i = 0; i < 3; i++) { 1222 ctlr->imu_cal_accel_divisor[i] = ctlr->accel_cal.scale[i] - 1223 ctlr->accel_cal.offset[i]; 1224 ctlr->imu_cal_gyro_divisor[i] = ctlr->gyro_cal.scale[i] - 1225 ctlr->gyro_cal.offset[i]; 1226 1227 if (ctlr->imu_cal_accel_divisor[i] == 0) { 1228 ctlr->imu_cal_accel_divisor[i] = 1; 1229 divz++; 1230 } 1231 1232 if (ctlr->imu_cal_gyro_divisor[i] == 0) { 1233 ctlr->imu_cal_gyro_divisor[i] = 1; 1234 divz++; 1235 } 1236 } 1237 1238 if (divz) 1239 hid_warn(ctlr->hdev, "inaccurate IMU divisors (%d)\n", divz); 1240} 1241 1242static const s16 DFLT_ACCEL_OFFSET /*= 0*/; 1243static const s16 DFLT_ACCEL_SCALE = 16384; 1244static const s16 DFLT_GYRO_OFFSET /*= 0*/; 1245static const s16 DFLT_GYRO_SCALE = 13371; 1246static int joycon_request_imu_calibration(struct joycon_ctlr *ctlr) 1247{ 1248 u16 imu_cal_addr = JC_IMU_CAL_FCT_DATA_ADDR; 1249 u8 *raw_cal; 1250 int ret; 1251 int i; 1252 1253 /* check if user calibration exists */ 1254 if (!joycon_check_for_cal_magic(ctlr, JC_IMU_CAL_USR_MAGIC_ADDR)) { 1255 imu_cal_addr = JC_IMU_CAL_USR_DATA_ADDR; 1256 hid_info(ctlr->hdev, "using user cal for IMU\n"); 1257 } else { 1258 hid_info(ctlr->hdev, "using factory cal for IMU\n"); 1259 } 1260 1261 /* request IMU calibration data */ 1262 hid_dbg(ctlr->hdev, "requesting IMU cal data\n"); 1263 ret = joycon_request_spi_flash_read(ctlr, imu_cal_addr, 1264 JC_IMU_CAL_DATA_SIZE, &raw_cal); 1265 if (ret) { 1266 hid_warn(ctlr->hdev, 1267 "Failed to read IMU cal, using defaults; ret=%d\n", 1268 ret); 1269 1270 for (i = 0; i < 3; i++) { 1271 ctlr->accel_cal.offset[i] = DFLT_ACCEL_OFFSET; 1272 ctlr->accel_cal.scale[i] = DFLT_ACCEL_SCALE; 1273 ctlr->gyro_cal.offset[i] = DFLT_GYRO_OFFSET; 1274 ctlr->gyro_cal.scale[i] = DFLT_GYRO_SCALE; 1275 } 1276 joycon_calc_imu_cal_divisors(ctlr); 1277 return ret; 1278 } 1279 1280 /* IMU calibration parsing */ 1281 for (i = 0; i < 3; i++) { 1282 int j = i * 2; 1283 1284 ctlr->accel_cal.offset[i] = get_unaligned_le16(raw_cal + j); 1285 ctlr->accel_cal.scale[i] = get_unaligned_le16(raw_cal + j + 6); 1286 ctlr->gyro_cal.offset[i] = get_unaligned_le16(raw_cal + j + 12); 1287 ctlr->gyro_cal.scale[i] = get_unaligned_le16(raw_cal + j + 18); 1288 } 1289 1290 joycon_calc_imu_cal_divisors(ctlr); 1291 1292 hid_dbg(ctlr->hdev, "IMU calibration:\n" 1293 "a_o[0]=%d a_o[1]=%d a_o[2]=%d\n" 1294 "a_s[0]=%d a_s[1]=%d a_s[2]=%d\n" 1295 "g_o[0]=%d g_o[1]=%d g_o[2]=%d\n" 1296 "g_s[0]=%d g_s[1]=%d g_s[2]=%d\n", 1297 ctlr->accel_cal.offset[0], 1298 ctlr->accel_cal.offset[1], 1299 ctlr->accel_cal.offset[2], 1300 ctlr->accel_cal.scale[0], 1301 ctlr->accel_cal.scale[1], 1302 ctlr->accel_cal.scale[2], 1303 ctlr->gyro_cal.offset[0], 1304 ctlr->gyro_cal.offset[1], 1305 ctlr->gyro_cal.offset[2], 1306 ctlr->gyro_cal.scale[0], 1307 ctlr->gyro_cal.scale[1], 1308 ctlr->gyro_cal.scale[2]); 1309 1310 return 0; 1311} 1312 1313static int joycon_set_report_mode(struct joycon_ctlr *ctlr) 1314{ 1315 struct joycon_subcmd_request *req; 1316 u8 buffer[sizeof(*req) + 1] = { 0 }; 1317 1318 req = (struct joycon_subcmd_request *)buffer; 1319 req->subcmd_id = JC_SUBCMD_SET_REPORT_MODE; 1320 req->data[0] = 0x30; /* standard, full report mode */ 1321 1322 hid_dbg(ctlr->hdev, "setting controller report mode\n"); 1323 return joycon_send_subcmd(ctlr, req, 1, HZ); 1324} 1325 1326static int joycon_enable_rumble(struct joycon_ctlr *ctlr) 1327{ 1328 struct joycon_subcmd_request *req; 1329 u8 buffer[sizeof(*req) + 1] = { 0 }; 1330 1331 req = (struct joycon_subcmd_request *)buffer; 1332 req->subcmd_id = JC_SUBCMD_ENABLE_VIBRATION; 1333 req->data[0] = 0x01; /* note: 0x00 would disable */ 1334 1335 hid_dbg(ctlr->hdev, "enabling rumble\n"); 1336 return joycon_send_subcmd(ctlr, req, 1, HZ/4); 1337} 1338 1339static int joycon_enable_imu(struct joycon_ctlr *ctlr) 1340{ 1341 struct joycon_subcmd_request *req; 1342 u8 buffer[sizeof(*req) + 1] = { 0 }; 1343 1344 req = (struct joycon_subcmd_request *)buffer; 1345 req->subcmd_id = JC_SUBCMD_ENABLE_IMU; 1346 req->data[0] = 0x01; /* note: 0x00 would disable */ 1347 1348 hid_dbg(ctlr->hdev, "enabling IMU\n"); 1349 return joycon_send_subcmd(ctlr, req, 1, HZ); 1350} 1351 1352static s32 joycon_map_stick_val(struct joycon_stick_cal *cal, s32 val) 1353{ 1354 s32 center = cal->center; 1355 s32 min = cal->min; 1356 s32 max = cal->max; 1357 s32 new_val; 1358 1359 if (val > center) { 1360 new_val = (val - center) * JC_MAX_STICK_MAG; 1361 new_val /= (max - center); 1362 } else { 1363 new_val = (center - val) * -JC_MAX_STICK_MAG; 1364 new_val /= (center - min); 1365 } 1366 new_val = clamp(new_val, (s32)-JC_MAX_STICK_MAG, (s32)JC_MAX_STICK_MAG); 1367 return new_val; 1368} 1369 1370static void joycon_input_report_parse_imu_data(struct joycon_ctlr *ctlr, 1371 struct joycon_input_report *rep, 1372 struct joycon_imu_data *imu_data) 1373{ 1374 u8 *raw = rep->imu_raw_bytes; 1375 int i; 1376 1377 for (i = 0; i < 3; i++) { 1378 struct joycon_imu_data *data = &imu_data[i]; 1379 1380 data->accel_x = get_unaligned_le16(raw + 0); 1381 data->accel_y = get_unaligned_le16(raw + 2); 1382 data->accel_z = get_unaligned_le16(raw + 4); 1383 data->gyro_x = get_unaligned_le16(raw + 6); 1384 data->gyro_y = get_unaligned_le16(raw + 8); 1385 data->gyro_z = get_unaligned_le16(raw + 10); 1386 /* point to next imu sample */ 1387 raw += sizeof(struct joycon_imu_data); 1388 } 1389} 1390 1391static void joycon_parse_imu_report(struct joycon_ctlr *ctlr, 1392 struct joycon_input_report *rep) 1393{ 1394 struct joycon_imu_data imu_data[3] = {0}; /* 3 reports per packet */ 1395 struct input_dev *idev = ctlr->imu_input; 1396 unsigned int msecs = jiffies_to_msecs(jiffies); 1397 unsigned int last_msecs = ctlr->imu_last_pkt_ms; 1398 int i; 1399 int value[6]; 1400 1401 joycon_input_report_parse_imu_data(ctlr, rep, imu_data); 1402 1403 /* 1404 * There are complexities surrounding how we determine the timestamps we 1405 * associate with the samples we pass to userspace. The IMU input 1406 * reports do not provide us with a good timestamp. There's a quickly 1407 * incrementing 8-bit counter per input report, but it is not very 1408 * useful for this purpose (it is not entirely clear what rate it 1409 * increments at or if it varies based on packet push rate - more on 1410 * the push rate below...). 1411 * 1412 * The reverse engineering work done on the joy-cons and pro controllers 1413 * by the community seems to indicate the following: 1414 * - The controller samples the IMU every 1.35ms. It then does some of 1415 * its own processing, probably averaging the samples out. 1416 * - Each imu input report contains 3 IMU samples, (usually 5ms apart). 1417 * - In the standard reporting mode (which this driver uses exclusively) 1418 * input reports are pushed from the controller as follows: 1419 * * joy-con (bluetooth): every 15 ms 1420 * * joy-cons (in charging grip via USB): every 15 ms 1421 * * pro controller (USB): every 15 ms 1422 * * pro controller (bluetooth): every 8 ms (this is the wildcard) 1423 * 1424 * Further complicating matters is that some bluetooth stacks are known 1425 * to alter the controller's packet rate by hardcoding the bluetooth 1426 * SSR for the switch controllers (android's stack currently sets the 1427 * SSR to 11ms for both the joy-cons and pro controllers). 1428 * 1429 * In my own testing, I've discovered that my pro controller either 1430 * reports IMU sample batches every 11ms or every 15ms. This rate is 1431 * stable after connecting. It isn't 100% clear what determines this 1432 * rate. Importantly, even when sending every 11ms, none of the samples 1433 * are duplicates. This seems to indicate that the time deltas between 1434 * reported samples can vary based on the input report rate. 1435 * 1436 * The solution employed in this driver is to keep track of the average 1437 * time delta between IMU input reports. In testing, this value has 1438 * proven to be stable, staying at 15ms or 11ms, though other hardware 1439 * configurations and bluetooth stacks could potentially see other rates 1440 * (hopefully this will become more clear as more people use the 1441 * driver). 1442 * 1443 * Keeping track of the average report delta allows us to submit our 1444 * timestamps to userspace based on that. Each report contains 3 1445 * samples, so the IMU sampling rate should be avg_time_delta/3. We can 1446 * also use this average to detect events where we have dropped a 1447 * packet. The userspace timestamp for the samples will be adjusted 1448 * accordingly to prevent unwanted behvaior. 1449 */ 1450 if (!ctlr->imu_first_packet_received) { 1451 ctlr->imu_timestamp_us = 0; 1452 ctlr->imu_delta_samples_count = 0; 1453 ctlr->imu_delta_samples_sum = 0; 1454 ctlr->imu_avg_delta_ms = JC_IMU_DFLT_AVG_DELTA_MS; 1455 ctlr->imu_first_packet_received = true; 1456 } else { 1457 unsigned int delta = msecs - last_msecs; 1458 unsigned int dropped_pkts; 1459 unsigned int dropped_threshold; 1460 1461 /* avg imu report delta housekeeping */ 1462 ctlr->imu_delta_samples_sum += delta; 1463 ctlr->imu_delta_samples_count++; 1464 if (ctlr->imu_delta_samples_count >= 1465 JC_IMU_SAMPLES_PER_DELTA_AVG) { 1466 ctlr->imu_avg_delta_ms = ctlr->imu_delta_samples_sum / 1467 ctlr->imu_delta_samples_count; 1468 ctlr->imu_delta_samples_count = 0; 1469 ctlr->imu_delta_samples_sum = 0; 1470 } 1471 1472 /* don't ever want divide by zero shenanigans */ 1473 if (ctlr->imu_avg_delta_ms == 0) { 1474 ctlr->imu_avg_delta_ms = 1; 1475 hid_warn(ctlr->hdev, "calculated avg imu delta of 0\n"); 1476 } 1477 1478 /* useful for debugging IMU sample rate */ 1479 hid_dbg(ctlr->hdev, 1480 "imu_report: ms=%u last_ms=%u delta=%u avg_delta=%u\n", 1481 msecs, last_msecs, delta, ctlr->imu_avg_delta_ms); 1482 1483 /* check if any packets have been dropped */ 1484 dropped_threshold = ctlr->imu_avg_delta_ms * 3 / 2; 1485 dropped_pkts = (delta - min(delta, dropped_threshold)) / 1486 ctlr->imu_avg_delta_ms; 1487 ctlr->imu_timestamp_us += 1000 * ctlr->imu_avg_delta_ms; 1488 if (dropped_pkts > JC_IMU_DROPPED_PKT_WARNING) { 1489 hid_warn(ctlr->hdev, 1490 "compensating for %u dropped IMU reports\n", 1491 dropped_pkts); 1492 hid_warn(ctlr->hdev, 1493 "delta=%u avg_delta=%u\n", 1494 delta, ctlr->imu_avg_delta_ms); 1495 } 1496 } 1497 ctlr->imu_last_pkt_ms = msecs; 1498 1499 /* Each IMU input report contains three samples */ 1500 for (i = 0; i < 3; i++) { 1501 input_event(idev, EV_MSC, MSC_TIMESTAMP, 1502 ctlr->imu_timestamp_us); 1503 1504 /* 1505 * These calculations (which use the controller's calibration 1506 * settings to improve the final values) are based on those 1507 * found in the community's reverse-engineering repo (linked at 1508 * top of driver). For hid-nintendo, we make sure that the final 1509 * value given to userspace is always in terms of the axis 1510 * resolution we provided. 1511 * 1512 * Currently only the gyro calculations subtract the calibration 1513 * offsets from the raw value itself. In testing, doing the same 1514 * for the accelerometer raw values decreased accuracy. 1515 * 1516 * Note that the gyro values are multiplied by the 1517 * precision-saving scaling factor to prevent large inaccuracies 1518 * due to truncation of the resolution value which would 1519 * otherwise occur. To prevent overflow (without resorting to 64 1520 * bit integer math), the mult_frac macro is used. 1521 */ 1522 value[0] = mult_frac((JC_IMU_PREC_RANGE_SCALE * 1523 (imu_data[i].gyro_x - 1524 ctlr->gyro_cal.offset[0])), 1525 ctlr->gyro_cal.scale[0], 1526 ctlr->imu_cal_gyro_divisor[0]); 1527 value[1] = mult_frac((JC_IMU_PREC_RANGE_SCALE * 1528 (imu_data[i].gyro_y - 1529 ctlr->gyro_cal.offset[1])), 1530 ctlr->gyro_cal.scale[1], 1531 ctlr->imu_cal_gyro_divisor[1]); 1532 value[2] = mult_frac((JC_IMU_PREC_RANGE_SCALE * 1533 (imu_data[i].gyro_z - 1534 ctlr->gyro_cal.offset[2])), 1535 ctlr->gyro_cal.scale[2], 1536 ctlr->imu_cal_gyro_divisor[2]); 1537 1538 value[3] = ((s32)imu_data[i].accel_x * 1539 ctlr->accel_cal.scale[0]) / 1540 ctlr->imu_cal_accel_divisor[0]; 1541 value[4] = ((s32)imu_data[i].accel_y * 1542 ctlr->accel_cal.scale[1]) / 1543 ctlr->imu_cal_accel_divisor[1]; 1544 value[5] = ((s32)imu_data[i].accel_z * 1545 ctlr->accel_cal.scale[2]) / 1546 ctlr->imu_cal_accel_divisor[2]; 1547 1548 hid_dbg(ctlr->hdev, "raw_gyro: g_x=%d g_y=%d g_z=%d\n", 1549 imu_data[i].gyro_x, imu_data[i].gyro_y, 1550 imu_data[i].gyro_z); 1551 hid_dbg(ctlr->hdev, "raw_accel: a_x=%d a_y=%d a_z=%d\n", 1552 imu_data[i].accel_x, imu_data[i].accel_y, 1553 imu_data[i].accel_z); 1554 1555 /* 1556 * The right joy-con has 2 axes negated, Y and Z. This is due to 1557 * the orientation of the IMU in the controller. We negate those 1558 * axes' values in order to be consistent with the left joy-con 1559 * and the pro controller: 1560 * X: positive is pointing toward the triggers 1561 * Y: positive is pointing to the left 1562 * Z: positive is pointing up (out of the buttons/sticks) 1563 * The axes follow the right-hand rule. 1564 */ 1565 if (jc_type_is_joycon(ctlr) && jc_type_has_right(ctlr)) { 1566 int j; 1567 1568 /* negate all but x axis */ 1569 for (j = 1; j < 6; ++j) { 1570 if (j == 3) 1571 continue; 1572 value[j] *= -1; 1573 } 1574 } 1575 1576 input_report_abs(idev, ABS_RX, value[0]); 1577 input_report_abs(idev, ABS_RY, value[1]); 1578 input_report_abs(idev, ABS_RZ, value[2]); 1579 input_report_abs(idev, ABS_X, value[3]); 1580 input_report_abs(idev, ABS_Y, value[4]); 1581 input_report_abs(idev, ABS_Z, value[5]); 1582 input_sync(idev); 1583 /* convert to micros and divide by 3 (3 samples per report). */ 1584 ctlr->imu_timestamp_us += ctlr->imu_avg_delta_ms * 1000 / 3; 1585 } 1586} 1587 1588static void joycon_handle_rumble_report(struct joycon_ctlr *ctlr, struct joycon_input_report *rep) 1589{ 1590 unsigned long flags; 1591 unsigned long msecs = jiffies_to_msecs(jiffies); 1592 1593 spin_lock_irqsave(&ctlr->lock, flags); 1594 if (IS_ENABLED(CONFIG_NINTENDO_FF) && rep->vibrator_report && 1595 ctlr->ctlr_state != JOYCON_CTLR_STATE_REMOVED && 1596 (msecs - ctlr->rumble_msecs) >= JC_RUMBLE_PERIOD_MS && 1597 (ctlr->rumble_queue_head != ctlr->rumble_queue_tail || 1598 ctlr->rumble_zero_countdown > 0)) { 1599 /* 1600 * When this value reaches 0, we know we've sent multiple 1601 * packets to the controller instructing it to disable rumble. 1602 * We can safely stop sending periodic rumble packets until the 1603 * next ff effect. 1604 */ 1605 if (ctlr->rumble_zero_countdown > 0) 1606 ctlr->rumble_zero_countdown--; 1607 queue_work(ctlr->rumble_queue, &ctlr->rumble_worker); 1608 } 1609 1610 spin_unlock_irqrestore(&ctlr->lock, flags); 1611} 1612 1613static void joycon_parse_battery_status(struct joycon_ctlr *ctlr, struct joycon_input_report *rep) 1614{ 1615 u8 tmp; 1616 unsigned long flags; 1617 1618 spin_lock_irqsave(&ctlr->lock, flags); 1619 1620 tmp = rep->bat_con; 1621 ctlr->host_powered = tmp & BIT(0); 1622 ctlr->battery_charging = tmp & BIT(4); 1623 tmp = tmp >> 5; 1624 1625 switch (tmp) { 1626 case 0: /* empty */ 1627 ctlr->battery_capacity = POWER_SUPPLY_CAPACITY_LEVEL_CRITICAL; 1628 break; 1629 case 1: /* low */ 1630 ctlr->battery_capacity = POWER_SUPPLY_CAPACITY_LEVEL_LOW; 1631 break; 1632 case 2: /* medium */ 1633 ctlr->battery_capacity = POWER_SUPPLY_CAPACITY_LEVEL_NORMAL; 1634 break; 1635 case 3: /* high */ 1636 ctlr->battery_capacity = POWER_SUPPLY_CAPACITY_LEVEL_HIGH; 1637 break; 1638 case 4: /* full */ 1639 ctlr->battery_capacity = POWER_SUPPLY_CAPACITY_LEVEL_FULL; 1640 break; 1641 default: 1642 ctlr->battery_capacity = POWER_SUPPLY_CAPACITY_LEVEL_UNKNOWN; 1643 hid_warn(ctlr->hdev, "Invalid battery status\n"); 1644 break; 1645 } 1646 1647 spin_unlock_irqrestore(&ctlr->lock, flags); 1648} 1649 1650static void joycon_report_left_stick(struct joycon_ctlr *ctlr, 1651 struct joycon_input_report *rep) 1652{ 1653 u16 raw_x; 1654 u16 raw_y; 1655 s32 x; 1656 s32 y; 1657 1658 raw_x = hid_field_extract(ctlr->hdev, rep->left_stick, 0, 12); 1659 raw_y = hid_field_extract(ctlr->hdev, rep->left_stick + 1, 4, 12); 1660 1661 x = joycon_map_stick_val(&ctlr->left_stick_cal_x, raw_x); 1662 y = -joycon_map_stick_val(&ctlr->left_stick_cal_y, raw_y); 1663 1664 input_report_abs(ctlr->input, ABS_X, x); 1665 input_report_abs(ctlr->input, ABS_Y, y); 1666} 1667 1668static void joycon_report_right_stick(struct joycon_ctlr *ctlr, 1669 struct joycon_input_report *rep) 1670{ 1671 u16 raw_x; 1672 u16 raw_y; 1673 s32 x; 1674 s32 y; 1675 1676 raw_x = hid_field_extract(ctlr->hdev, rep->right_stick, 0, 12); 1677 raw_y = hid_field_extract(ctlr->hdev, rep->right_stick + 1, 4, 12); 1678 1679 x = joycon_map_stick_val(&ctlr->right_stick_cal_x, raw_x); 1680 y = -joycon_map_stick_val(&ctlr->right_stick_cal_y, raw_y); 1681 1682 input_report_abs(ctlr->input, ABS_RX, x); 1683 input_report_abs(ctlr->input, ABS_RY, y); 1684} 1685 1686static void joycon_report_dpad(struct joycon_ctlr *ctlr, 1687 struct joycon_input_report *rep) 1688{ 1689 int hatx = 0; 1690 int haty = 0; 1691 u32 btns = hid_field_extract(ctlr->hdev, rep->button_status, 0, 24); 1692 1693 if (btns & JC_BTN_LEFT) 1694 hatx = -1; 1695 else if (btns & JC_BTN_RIGHT) 1696 hatx = 1; 1697 1698 if (btns & JC_BTN_UP) 1699 haty = -1; 1700 else if (btns & JC_BTN_DOWN) 1701 haty = 1; 1702 1703 input_report_abs(ctlr->input, ABS_HAT0X, hatx); 1704 input_report_abs(ctlr->input, ABS_HAT0Y, haty); 1705} 1706 1707static void joycon_report_buttons(struct joycon_ctlr *ctlr, 1708 struct joycon_input_report *rep, 1709 const struct joycon_ctlr_button_mapping button_mappings[]) 1710{ 1711 const struct joycon_ctlr_button_mapping *button; 1712 u32 status = hid_field_extract(ctlr->hdev, rep->button_status, 0, 24); 1713 1714 for (button = button_mappings; button->code; button++) 1715 input_report_key(ctlr->input, button->code, status & button->bit); 1716} 1717 1718static void joycon_parse_report(struct joycon_ctlr *ctlr, 1719 struct joycon_input_report *rep) 1720{ 1721 unsigned long flags; 1722 unsigned long msecs = jiffies_to_msecs(jiffies); 1723 unsigned long report_delta_ms = msecs - ctlr->last_input_report_msecs; 1724 1725 if (joycon_has_rumble(ctlr)) 1726 joycon_handle_rumble_report(ctlr, rep); 1727 1728 joycon_parse_battery_status(ctlr, rep); 1729 1730 if (joycon_type_is_left_joycon(ctlr)) { 1731 joycon_report_left_stick(ctlr, rep); 1732 joycon_report_buttons(ctlr, rep, left_joycon_button_mappings); 1733 if (!joycon_device_is_chrggrip(ctlr)) 1734 joycon_report_buttons(ctlr, rep, left_joycon_s_button_mappings); 1735 } else if (joycon_type_is_right_joycon(ctlr)) { 1736 joycon_report_right_stick(ctlr, rep); 1737 joycon_report_buttons(ctlr, rep, right_joycon_button_mappings); 1738 if (!joycon_device_is_chrggrip(ctlr)) 1739 joycon_report_buttons(ctlr, rep, right_joycon_s_button_mappings); 1740 } else if (joycon_type_is_procon(ctlr)) { 1741 joycon_report_left_stick(ctlr, rep); 1742 joycon_report_right_stick(ctlr, rep); 1743 joycon_report_dpad(ctlr, rep); 1744 joycon_report_buttons(ctlr, rep, procon_button_mappings); 1745 } else if (joycon_type_is_any_nescon(ctlr)) { 1746 joycon_report_dpad(ctlr, rep); 1747 joycon_report_buttons(ctlr, rep, nescon_button_mappings); 1748 } else if (joycon_type_is_snescon(ctlr)) { 1749 joycon_report_dpad(ctlr, rep); 1750 joycon_report_buttons(ctlr, rep, snescon_button_mappings); 1751 } else if (joycon_type_is_gencon(ctlr)) { 1752 joycon_report_dpad(ctlr, rep); 1753 joycon_report_buttons(ctlr, rep, gencon_button_mappings); 1754 } else if (joycon_type_is_n64con(ctlr)) { 1755 joycon_report_left_stick(ctlr, rep); 1756 joycon_report_dpad(ctlr, rep); 1757 joycon_report_buttons(ctlr, rep, n64con_button_mappings); 1758 } 1759 1760 input_sync(ctlr->input); 1761 1762 spin_lock_irqsave(&ctlr->lock, flags); 1763 ctlr->last_input_report_msecs = msecs; 1764 /* 1765 * Was this input report a reasonable time delta compared to the prior 1766 * report? We use this information to decide when a safe time is to send 1767 * rumble packets or subcommand packets. 1768 */ 1769 if (report_delta_ms >= JC_INPUT_REPORT_MIN_DELTA && 1770 report_delta_ms <= JC_INPUT_REPORT_MAX_DELTA) { 1771 if (ctlr->consecutive_valid_report_deltas < JC_SUBCMD_VALID_DELTA_REQ) 1772 ctlr->consecutive_valid_report_deltas++; 1773 } else { 1774 ctlr->consecutive_valid_report_deltas = 0; 1775 } 1776 /* 1777 * Our consecutive valid report tracking is only relevant for 1778 * bluetooth-connected controllers. For USB devices, we're beholden to 1779 * USB's underlying polling rate anyway. Always set to the consecutive 1780 * delta requirement. 1781 */ 1782 if (ctlr->hdev->bus == BUS_USB) 1783 ctlr->consecutive_valid_report_deltas = JC_SUBCMD_VALID_DELTA_REQ; 1784 1785 spin_unlock_irqrestore(&ctlr->lock, flags); 1786 1787 /* 1788 * Immediately after receiving a report is the most reliable time to 1789 * send a subcommand to the controller. Wake any subcommand senders 1790 * waiting for a report. 1791 */ 1792 if (unlikely(mutex_is_locked(&ctlr->output_mutex))) { 1793 spin_lock_irqsave(&ctlr->lock, flags); 1794 ctlr->received_input_report = true; 1795 spin_unlock_irqrestore(&ctlr->lock, flags); 1796 wake_up(&ctlr->wait); 1797 } 1798 1799 /* parse IMU data if present */ 1800 if ((rep->id == JC_INPUT_IMU_DATA) && joycon_has_imu(ctlr)) 1801 joycon_parse_imu_report(ctlr, rep); 1802} 1803 1804static int joycon_send_rumble_data(struct joycon_ctlr *ctlr) 1805{ 1806 int ret; 1807 unsigned long flags; 1808 struct joycon_rumble_output rumble_output = { 0 }; 1809 1810 spin_lock_irqsave(&ctlr->lock, flags); 1811 /* 1812 * If the controller has been removed, just return ENODEV so the LED 1813 * subsystem doesn't print invalid errors on removal. 1814 */ 1815 if (ctlr->ctlr_state == JOYCON_CTLR_STATE_REMOVED) { 1816 spin_unlock_irqrestore(&ctlr->lock, flags); 1817 return -ENODEV; 1818 } 1819 memcpy(rumble_output.rumble_data, 1820 ctlr->rumble_data[ctlr->rumble_queue_tail], 1821 JC_RUMBLE_DATA_SIZE); 1822 spin_unlock_irqrestore(&ctlr->lock, flags); 1823 1824 rumble_output.output_id = JC_OUTPUT_RUMBLE_ONLY; 1825 rumble_output.packet_num = ctlr->subcmd_num; 1826 if (++ctlr->subcmd_num > 0xF) 1827 ctlr->subcmd_num = 0; 1828 1829 joycon_enforce_subcmd_rate(ctlr); 1830 1831 ret = __joycon_hid_send(ctlr->hdev, (u8 *)&rumble_output, 1832 sizeof(rumble_output)); 1833 return ret; 1834} 1835 1836static void joycon_rumble_worker(struct work_struct *work) 1837{ 1838 struct joycon_ctlr *ctlr = container_of(work, struct joycon_ctlr, 1839 rumble_worker); 1840 unsigned long flags; 1841 bool again = true; 1842 int ret; 1843 1844 while (again) { 1845 mutex_lock(&ctlr->output_mutex); 1846 ret = joycon_send_rumble_data(ctlr); 1847 mutex_unlock(&ctlr->output_mutex); 1848 1849 /* -ENODEV means the controller was just unplugged */ 1850 spin_lock_irqsave(&ctlr->lock, flags); 1851 if (ret < 0 && ret != -ENODEV && 1852 ctlr->ctlr_state != JOYCON_CTLR_STATE_REMOVED) 1853 hid_warn(ctlr->hdev, "Failed to set rumble; e=%d", ret); 1854 1855 ctlr->rumble_msecs = jiffies_to_msecs(jiffies); 1856 if (ctlr->rumble_queue_tail != ctlr->rumble_queue_head) { 1857 if (++ctlr->rumble_queue_tail >= JC_RUMBLE_QUEUE_SIZE) 1858 ctlr->rumble_queue_tail = 0; 1859 } else { 1860 again = false; 1861 } 1862 spin_unlock_irqrestore(&ctlr->lock, flags); 1863 } 1864} 1865 1866#if IS_ENABLED(CONFIG_NINTENDO_FF) 1867static struct joycon_rumble_freq_data joycon_find_rumble_freq(u16 freq) 1868{ 1869 const size_t length = ARRAY_SIZE(joycon_rumble_frequencies); 1870 const struct joycon_rumble_freq_data *data = joycon_rumble_frequencies; 1871 int i = 0; 1872 1873 if (freq > data[0].freq) { 1874 for (i = 1; i < length - 1; i++) { 1875 if (freq > data[i - 1].freq && freq <= data[i].freq) 1876 break; 1877 } 1878 } 1879 1880 return data[i]; 1881} 1882 1883static struct joycon_rumble_amp_data joycon_find_rumble_amp(u16 amp) 1884{ 1885 const size_t length = ARRAY_SIZE(joycon_rumble_amplitudes); 1886 const struct joycon_rumble_amp_data *data = joycon_rumble_amplitudes; 1887 int i = 0; 1888 1889 if (amp > data[0].amp) { 1890 for (i = 1; i < length - 1; i++) { 1891 if (amp > data[i - 1].amp && amp <= data[i].amp) 1892 break; 1893 } 1894 } 1895 1896 return data[i]; 1897} 1898 1899static void joycon_encode_rumble(u8 *data, u16 freq_low, u16 freq_high, u16 amp) 1900{ 1901 struct joycon_rumble_freq_data freq_data_low; 1902 struct joycon_rumble_freq_data freq_data_high; 1903 struct joycon_rumble_amp_data amp_data; 1904 1905 freq_data_low = joycon_find_rumble_freq(freq_low); 1906 freq_data_high = joycon_find_rumble_freq(freq_high); 1907 amp_data = joycon_find_rumble_amp(amp); 1908 1909 data[0] = (freq_data_high.high >> 8) & 0xFF; 1910 data[1] = (freq_data_high.high & 0xFF) + amp_data.high; 1911 data[2] = freq_data_low.low + ((amp_data.low >> 8) & 0xFF); 1912 data[3] = amp_data.low & 0xFF; 1913} 1914 1915static const u16 JOYCON_MAX_RUMBLE_HIGH_FREQ = 1253; 1916static const u16 JOYCON_MIN_RUMBLE_HIGH_FREQ = 82; 1917static const u16 JOYCON_MAX_RUMBLE_LOW_FREQ = 626; 1918static const u16 JOYCON_MIN_RUMBLE_LOW_FREQ = 41; 1919 1920static void joycon_clamp_rumble_freqs(struct joycon_ctlr *ctlr) 1921{ 1922 unsigned long flags; 1923 1924 spin_lock_irqsave(&ctlr->lock, flags); 1925 ctlr->rumble_ll_freq = clamp(ctlr->rumble_ll_freq, 1926 JOYCON_MIN_RUMBLE_LOW_FREQ, 1927 JOYCON_MAX_RUMBLE_LOW_FREQ); 1928 ctlr->rumble_lh_freq = clamp(ctlr->rumble_lh_freq, 1929 JOYCON_MIN_RUMBLE_HIGH_FREQ, 1930 JOYCON_MAX_RUMBLE_HIGH_FREQ); 1931 ctlr->rumble_rl_freq = clamp(ctlr->rumble_rl_freq, 1932 JOYCON_MIN_RUMBLE_LOW_FREQ, 1933 JOYCON_MAX_RUMBLE_LOW_FREQ); 1934 ctlr->rumble_rh_freq = clamp(ctlr->rumble_rh_freq, 1935 JOYCON_MIN_RUMBLE_HIGH_FREQ, 1936 JOYCON_MAX_RUMBLE_HIGH_FREQ); 1937 spin_unlock_irqrestore(&ctlr->lock, flags); 1938} 1939 1940static int joycon_set_rumble(struct joycon_ctlr *ctlr, u16 amp_r, u16 amp_l, 1941 bool schedule_now) 1942{ 1943 u8 data[JC_RUMBLE_DATA_SIZE]; 1944 u16 amp; 1945 u16 freq_r_low; 1946 u16 freq_r_high; 1947 u16 freq_l_low; 1948 u16 freq_l_high; 1949 unsigned long flags; 1950 int next_rq_head; 1951 1952 spin_lock_irqsave(&ctlr->lock, flags); 1953 freq_r_low = ctlr->rumble_rl_freq; 1954 freq_r_high = ctlr->rumble_rh_freq; 1955 freq_l_low = ctlr->rumble_ll_freq; 1956 freq_l_high = ctlr->rumble_lh_freq; 1957 /* limit number of silent rumble packets to reduce traffic */ 1958 if (amp_l != 0 || amp_r != 0) 1959 ctlr->rumble_zero_countdown = JC_RUMBLE_ZERO_AMP_PKT_CNT; 1960 spin_unlock_irqrestore(&ctlr->lock, flags); 1961 1962 /* right joy-con */ 1963 amp = amp_r * (u32)joycon_max_rumble_amp / 65535; 1964 joycon_encode_rumble(data + 4, freq_r_low, freq_r_high, amp); 1965 1966 /* left joy-con */ 1967 amp = amp_l * (u32)joycon_max_rumble_amp / 65535; 1968 joycon_encode_rumble(data, freq_l_low, freq_l_high, amp); 1969 1970 spin_lock_irqsave(&ctlr->lock, flags); 1971 1972 next_rq_head = ctlr->rumble_queue_head + 1; 1973 if (next_rq_head >= JC_RUMBLE_QUEUE_SIZE) 1974 next_rq_head = 0; 1975 1976 /* Did we overrun the circular buffer? 1977 * If so, be sure we keep the latest intended rumble state. 1978 */ 1979 if (next_rq_head == ctlr->rumble_queue_tail) { 1980 hid_dbg(ctlr->hdev, "rumble queue is full"); 1981 /* overwrite the prior value at the end of the circular buf */ 1982 next_rq_head = ctlr->rumble_queue_head; 1983 } 1984 1985 ctlr->rumble_queue_head = next_rq_head; 1986 memcpy(ctlr->rumble_data[ctlr->rumble_queue_head], data, 1987 JC_RUMBLE_DATA_SIZE); 1988 1989 /* don't wait for the periodic send (reduces latency) */ 1990 if (schedule_now && ctlr->ctlr_state != JOYCON_CTLR_STATE_REMOVED) 1991 queue_work(ctlr->rumble_queue, &ctlr->rumble_worker); 1992 1993 spin_unlock_irqrestore(&ctlr->lock, flags); 1994 1995 return 0; 1996} 1997 1998static int joycon_play_effect(struct input_dev *dev, void *data, 1999 struct ff_effect *effect) 2000{ 2001 struct joycon_ctlr *ctlr = input_get_drvdata(dev); 2002 2003 if (effect->type != FF_RUMBLE) 2004 return 0; 2005 2006 return joycon_set_rumble(ctlr, 2007 effect->u.rumble.weak_magnitude, 2008 effect->u.rumble.strong_magnitude, 2009 true); 2010} 2011#endif /* IS_ENABLED(CONFIG_NINTENDO_FF) */ 2012 2013static void joycon_config_left_stick(struct input_dev *idev) 2014{ 2015 input_set_abs_params(idev, 2016 ABS_X, 2017 -JC_MAX_STICK_MAG, 2018 JC_MAX_STICK_MAG, 2019 JC_STICK_FUZZ, 2020 JC_STICK_FLAT); 2021 input_set_abs_params(idev, 2022 ABS_Y, 2023 -JC_MAX_STICK_MAG, 2024 JC_MAX_STICK_MAG, 2025 JC_STICK_FUZZ, 2026 JC_STICK_FLAT); 2027} 2028 2029static void joycon_config_right_stick(struct input_dev *idev) 2030{ 2031 input_set_abs_params(idev, 2032 ABS_RX, 2033 -JC_MAX_STICK_MAG, 2034 JC_MAX_STICK_MAG, 2035 JC_STICK_FUZZ, 2036 JC_STICK_FLAT); 2037 input_set_abs_params(idev, 2038 ABS_RY, 2039 -JC_MAX_STICK_MAG, 2040 JC_MAX_STICK_MAG, 2041 JC_STICK_FUZZ, 2042 JC_STICK_FLAT); 2043} 2044 2045static void joycon_config_dpad(struct input_dev *idev) 2046{ 2047 input_set_abs_params(idev, 2048 ABS_HAT0X, 2049 -JC_MAX_DPAD_MAG, 2050 JC_MAX_DPAD_MAG, 2051 JC_DPAD_FUZZ, 2052 JC_DPAD_FLAT); 2053 input_set_abs_params(idev, 2054 ABS_HAT0Y, 2055 -JC_MAX_DPAD_MAG, 2056 JC_MAX_DPAD_MAG, 2057 JC_DPAD_FUZZ, 2058 JC_DPAD_FLAT); 2059} 2060 2061static void joycon_config_buttons(struct input_dev *idev, 2062 const struct joycon_ctlr_button_mapping button_mappings[]) 2063{ 2064 const struct joycon_ctlr_button_mapping *button; 2065 2066 for (button = button_mappings; button->code; button++) 2067 input_set_capability(idev, EV_KEY, button->code); 2068} 2069 2070static void joycon_config_rumble(struct joycon_ctlr *ctlr) 2071{ 2072#if IS_ENABLED(CONFIG_NINTENDO_FF) 2073 /* set up rumble */ 2074 input_set_capability(ctlr->input, EV_FF, FF_RUMBLE); 2075 input_ff_create_memless(ctlr->input, NULL, joycon_play_effect); 2076 ctlr->rumble_ll_freq = JC_RUMBLE_DFLT_LOW_FREQ; 2077 ctlr->rumble_lh_freq = JC_RUMBLE_DFLT_HIGH_FREQ; 2078 ctlr->rumble_rl_freq = JC_RUMBLE_DFLT_LOW_FREQ; 2079 ctlr->rumble_rh_freq = JC_RUMBLE_DFLT_HIGH_FREQ; 2080 joycon_clamp_rumble_freqs(ctlr); 2081 joycon_set_rumble(ctlr, 0, 0, false); 2082 ctlr->rumble_msecs = jiffies_to_msecs(jiffies); 2083#endif 2084} 2085 2086static int joycon_imu_input_create(struct joycon_ctlr *ctlr) 2087{ 2088 struct hid_device *hdev; 2089 const char *imu_name; 2090 int ret; 2091 2092 hdev = ctlr->hdev; 2093 2094 /* configure the imu input device */ 2095 ctlr->imu_input = devm_input_allocate_device(&hdev->dev); 2096 if (!ctlr->imu_input) 2097 return -ENOMEM; 2098 2099 ctlr->imu_input->id.bustype = hdev->bus; 2100 ctlr->imu_input->id.vendor = hdev->vendor; 2101 ctlr->imu_input->id.product = hdev->product; 2102 ctlr->imu_input->id.version = hdev->version; 2103 ctlr->imu_input->uniq = ctlr->mac_addr_str; 2104 ctlr->imu_input->phys = hdev->phys; 2105 2106 imu_name = devm_kasprintf(&hdev->dev, GFP_KERNEL, "%s (IMU)", ctlr->input->name); 2107 if (!imu_name) 2108 return -ENOMEM; 2109 2110 ctlr->imu_input->name = imu_name; 2111 2112 input_set_drvdata(ctlr->imu_input, ctlr); 2113 2114 /* configure imu axes */ 2115 input_set_abs_params(ctlr->imu_input, ABS_X, 2116 -JC_IMU_MAX_ACCEL_MAG, JC_IMU_MAX_ACCEL_MAG, 2117 JC_IMU_ACCEL_FUZZ, JC_IMU_ACCEL_FLAT); 2118 input_set_abs_params(ctlr->imu_input, ABS_Y, 2119 -JC_IMU_MAX_ACCEL_MAG, JC_IMU_MAX_ACCEL_MAG, 2120 JC_IMU_ACCEL_FUZZ, JC_IMU_ACCEL_FLAT); 2121 input_set_abs_params(ctlr->imu_input, ABS_Z, 2122 -JC_IMU_MAX_ACCEL_MAG, JC_IMU_MAX_ACCEL_MAG, 2123 JC_IMU_ACCEL_FUZZ, JC_IMU_ACCEL_FLAT); 2124 input_abs_set_res(ctlr->imu_input, ABS_X, JC_IMU_ACCEL_RES_PER_G); 2125 input_abs_set_res(ctlr->imu_input, ABS_Y, JC_IMU_ACCEL_RES_PER_G); 2126 input_abs_set_res(ctlr->imu_input, ABS_Z, JC_IMU_ACCEL_RES_PER_G); 2127 2128 input_set_abs_params(ctlr->imu_input, ABS_RX, 2129 -JC_IMU_MAX_GYRO_MAG, JC_IMU_MAX_GYRO_MAG, 2130 JC_IMU_GYRO_FUZZ, JC_IMU_GYRO_FLAT); 2131 input_set_abs_params(ctlr->imu_input, ABS_RY, 2132 -JC_IMU_MAX_GYRO_MAG, JC_IMU_MAX_GYRO_MAG, 2133 JC_IMU_GYRO_FUZZ, JC_IMU_GYRO_FLAT); 2134 input_set_abs_params(ctlr->imu_input, ABS_RZ, 2135 -JC_IMU_MAX_GYRO_MAG, JC_IMU_MAX_GYRO_MAG, 2136 JC_IMU_GYRO_FUZZ, JC_IMU_GYRO_FLAT); 2137 2138 input_abs_set_res(ctlr->imu_input, ABS_RX, JC_IMU_GYRO_RES_PER_DPS); 2139 input_abs_set_res(ctlr->imu_input, ABS_RY, JC_IMU_GYRO_RES_PER_DPS); 2140 input_abs_set_res(ctlr->imu_input, ABS_RZ, JC_IMU_GYRO_RES_PER_DPS); 2141 2142 __set_bit(EV_MSC, ctlr->imu_input->evbit); 2143 __set_bit(MSC_TIMESTAMP, ctlr->imu_input->mscbit); 2144 __set_bit(INPUT_PROP_ACCELEROMETER, ctlr->imu_input->propbit); 2145 2146 ret = input_register_device(ctlr->imu_input); 2147 if (ret) 2148 return ret; 2149 2150 return 0; 2151} 2152 2153static int joycon_input_create(struct joycon_ctlr *ctlr) 2154{ 2155 struct hid_device *hdev; 2156 int ret; 2157 2158 hdev = ctlr->hdev; 2159 2160 ctlr->input = devm_input_allocate_device(&hdev->dev); 2161 if (!ctlr->input) 2162 return -ENOMEM; 2163 ctlr->input->id.bustype = hdev->bus; 2164 ctlr->input->id.vendor = hdev->vendor; 2165 ctlr->input->id.product = hdev->product; 2166 ctlr->input->id.version = hdev->version; 2167 ctlr->input->uniq = ctlr->mac_addr_str; 2168 ctlr->input->name = hdev->name; 2169 ctlr->input->phys = hdev->phys; 2170 input_set_drvdata(ctlr->input, ctlr); 2171 2172 ret = input_register_device(ctlr->input); 2173 if (ret) 2174 return ret; 2175 2176 if (joycon_type_is_right_joycon(ctlr)) { 2177 joycon_config_right_stick(ctlr->input); 2178 joycon_config_buttons(ctlr->input, right_joycon_button_mappings); 2179 if (!joycon_device_is_chrggrip(ctlr)) 2180 joycon_config_buttons(ctlr->input, right_joycon_s_button_mappings); 2181 } else if (joycon_type_is_left_joycon(ctlr)) { 2182 joycon_config_left_stick(ctlr->input); 2183 joycon_config_buttons(ctlr->input, left_joycon_button_mappings); 2184 if (!joycon_device_is_chrggrip(ctlr)) 2185 joycon_config_buttons(ctlr->input, left_joycon_s_button_mappings); 2186 } else if (joycon_type_is_procon(ctlr)) { 2187 joycon_config_left_stick(ctlr->input); 2188 joycon_config_right_stick(ctlr->input); 2189 joycon_config_dpad(ctlr->input); 2190 joycon_config_buttons(ctlr->input, procon_button_mappings); 2191 } else if (joycon_type_is_any_nescon(ctlr)) { 2192 joycon_config_dpad(ctlr->input); 2193 joycon_config_buttons(ctlr->input, nescon_button_mappings); 2194 } else if (joycon_type_is_snescon(ctlr)) { 2195 joycon_config_dpad(ctlr->input); 2196 joycon_config_buttons(ctlr->input, snescon_button_mappings); 2197 } else if (joycon_type_is_gencon(ctlr)) { 2198 joycon_config_dpad(ctlr->input); 2199 joycon_config_buttons(ctlr->input, gencon_button_mappings); 2200 } else if (joycon_type_is_n64con(ctlr)) { 2201 joycon_config_dpad(ctlr->input); 2202 joycon_config_left_stick(ctlr->input); 2203 joycon_config_buttons(ctlr->input, n64con_button_mappings); 2204 } 2205 2206 if (joycon_has_imu(ctlr)) { 2207 ret = joycon_imu_input_create(ctlr); 2208 if (ret) 2209 return ret; 2210 } 2211 2212 if (joycon_has_rumble(ctlr)) 2213 joycon_config_rumble(ctlr); 2214 2215 return 0; 2216} 2217 2218/* Because the subcommand sets all the leds at once, the brightness argument is ignored */ 2219static int joycon_player_led_brightness_set(struct led_classdev *led, 2220 enum led_brightness brightness) 2221{ 2222 struct device *dev = led->dev->parent; 2223 struct hid_device *hdev = to_hid_device(dev); 2224 struct joycon_ctlr *ctlr; 2225 int val = 0; 2226 int i; 2227 int ret; 2228 2229 ctlr = hid_get_drvdata(hdev); 2230 if (!ctlr) { 2231 hid_err(hdev, "No controller data\n"); 2232 return -ENODEV; 2233 } 2234 2235 for (i = 0; i < JC_NUM_LEDS; i++) 2236 val |= ctlr->leds[i].brightness << i; 2237 2238 mutex_lock(&ctlr->output_mutex); 2239 ret = joycon_set_player_leds(ctlr, 0, val); 2240 mutex_unlock(&ctlr->output_mutex); 2241 2242 return ret; 2243} 2244 2245static int joycon_home_led_brightness_set(struct led_classdev *led, 2246 enum led_brightness brightness) 2247{ 2248 struct device *dev = led->dev->parent; 2249 struct hid_device *hdev = to_hid_device(dev); 2250 struct joycon_ctlr *ctlr; 2251 int ret; 2252 2253 ctlr = hid_get_drvdata(hdev); 2254 if (!ctlr) { 2255 hid_err(hdev, "No controller data\n"); 2256 return -ENODEV; 2257 } 2258 mutex_lock(&ctlr->output_mutex); 2259 ret = joycon_set_home_led(ctlr, brightness); 2260 mutex_unlock(&ctlr->output_mutex); 2261 return ret; 2262} 2263 2264static DEFINE_SPINLOCK(joycon_input_num_spinlock); 2265static int joycon_leds_create(struct joycon_ctlr *ctlr) 2266{ 2267 struct hid_device *hdev = ctlr->hdev; 2268 struct device *dev = &hdev->dev; 2269 const char *d_name = dev_name(dev); 2270 struct led_classdev *led; 2271 int led_val = 0; 2272 char *name; 2273 int ret; 2274 int i; 2275 unsigned long flags; 2276 int player_led_pattern; 2277 static int input_num; 2278 2279 /* 2280 * Set the player leds based on controller number 2281 * Because there is no standard concept of "player number", the pattern 2282 * number will simply increase by 1 every time a controller is connected. 2283 */ 2284 spin_lock_irqsave(&joycon_input_num_spinlock, flags); 2285 player_led_pattern = input_num++ % JC_NUM_LED_PATTERNS; 2286 spin_unlock_irqrestore(&joycon_input_num_spinlock, flags); 2287 2288 /* configure the player LEDs */ 2289 for (i = 0; i < JC_NUM_LEDS; i++) { 2290 name = devm_kasprintf(dev, GFP_KERNEL, "%s:%s:%s", 2291 d_name, 2292 "green", 2293 joycon_player_led_names[i]); 2294 if (!name) 2295 return -ENOMEM; 2296 2297 led = &ctlr->leds[i]; 2298 led->name = name; 2299 led->brightness = joycon_player_led_patterns[player_led_pattern][i]; 2300 led->max_brightness = 1; 2301 led->brightness_set_blocking = 2302 joycon_player_led_brightness_set; 2303 led->flags = LED_CORE_SUSPENDRESUME | LED_HW_PLUGGABLE; 2304 2305 led_val |= joycon_player_led_patterns[player_led_pattern][i] << i; 2306 } 2307 mutex_lock(&ctlr->output_mutex); 2308 ret = joycon_set_player_leds(ctlr, 0, led_val); 2309 mutex_unlock(&ctlr->output_mutex); 2310 if (ret) { 2311 hid_warn(hdev, "Failed to set players LEDs, skipping registration; ret=%d\n", ret); 2312 goto home_led; 2313 } 2314 2315 for (i = 0; i < JC_NUM_LEDS; i++) { 2316 led = &ctlr->leds[i]; 2317 ret = devm_led_classdev_register(&hdev->dev, led); 2318 if (ret) { 2319 hid_err(hdev, "Failed to register player %d LED; ret=%d\n", i + 1, ret); 2320 return ret; 2321 } 2322 } 2323 2324home_led: 2325 /* configure the home LED */ 2326 if (jc_type_has_right(ctlr)) { 2327 name = devm_kasprintf(dev, GFP_KERNEL, "%s:%s:%s", 2328 d_name, 2329 "blue", 2330 LED_FUNCTION_PLAYER5); 2331 if (!name) 2332 return -ENOMEM; 2333 2334 led = &ctlr->home_led; 2335 led->name = name; 2336 led->brightness = 0; 2337 led->max_brightness = 0xF; 2338 led->brightness_set_blocking = joycon_home_led_brightness_set; 2339 led->flags = LED_CORE_SUSPENDRESUME | LED_HW_PLUGGABLE; 2340 2341 /* Set the home LED to 0 as default state */ 2342 mutex_lock(&ctlr->output_mutex); 2343 ret = joycon_set_home_led(ctlr, 0); 2344 mutex_unlock(&ctlr->output_mutex); 2345 if (ret) { 2346 hid_warn(hdev, "Failed to set home LED, skipping registration; ret=%d\n", ret); 2347 return 0; 2348 } 2349 2350 ret = devm_led_classdev_register(&hdev->dev, led); 2351 if (ret) { 2352 hid_err(hdev, "Failed to register home LED; ret=%d\n", ret); 2353 return ret; 2354 } 2355 } 2356 2357 return 0; 2358} 2359 2360static int joycon_battery_get_property(struct power_supply *supply, 2361 enum power_supply_property prop, 2362 union power_supply_propval *val) 2363{ 2364 struct joycon_ctlr *ctlr = power_supply_get_drvdata(supply); 2365 unsigned long flags; 2366 int ret = 0; 2367 u8 capacity; 2368 bool charging; 2369 bool powered; 2370 2371 spin_lock_irqsave(&ctlr->lock, flags); 2372 capacity = ctlr->battery_capacity; 2373 charging = ctlr->battery_charging; 2374 powered = ctlr->host_powered; 2375 spin_unlock_irqrestore(&ctlr->lock, flags); 2376 2377 switch (prop) { 2378 case POWER_SUPPLY_PROP_PRESENT: 2379 val->intval = 1; 2380 break; 2381 case POWER_SUPPLY_PROP_SCOPE: 2382 val->intval = POWER_SUPPLY_SCOPE_DEVICE; 2383 break; 2384 case POWER_SUPPLY_PROP_CAPACITY_LEVEL: 2385 val->intval = capacity; 2386 break; 2387 case POWER_SUPPLY_PROP_STATUS: 2388 if (charging) 2389 val->intval = POWER_SUPPLY_STATUS_CHARGING; 2390 else if (capacity == POWER_SUPPLY_CAPACITY_LEVEL_FULL && 2391 powered) 2392 val->intval = POWER_SUPPLY_STATUS_FULL; 2393 else 2394 val->intval = POWER_SUPPLY_STATUS_DISCHARGING; 2395 break; 2396 default: 2397 ret = -EINVAL; 2398 break; 2399 } 2400 return ret; 2401} 2402 2403static enum power_supply_property joycon_battery_props[] = { 2404 POWER_SUPPLY_PROP_PRESENT, 2405 POWER_SUPPLY_PROP_CAPACITY_LEVEL, 2406 POWER_SUPPLY_PROP_SCOPE, 2407 POWER_SUPPLY_PROP_STATUS, 2408}; 2409 2410static int joycon_power_supply_create(struct joycon_ctlr *ctlr) 2411{ 2412 struct hid_device *hdev = ctlr->hdev; 2413 struct power_supply_config supply_config = { .drv_data = ctlr, }; 2414 const char * const name_fmt = "nintendo_switch_controller_battery_%s"; 2415 int ret = 0; 2416 2417 /* Set initially to unknown before receiving first input report */ 2418 ctlr->battery_capacity = POWER_SUPPLY_CAPACITY_LEVEL_UNKNOWN; 2419 2420 /* Configure the battery's description */ 2421 ctlr->battery_desc.properties = joycon_battery_props; 2422 ctlr->battery_desc.num_properties = 2423 ARRAY_SIZE(joycon_battery_props); 2424 ctlr->battery_desc.get_property = joycon_battery_get_property; 2425 ctlr->battery_desc.type = POWER_SUPPLY_TYPE_BATTERY; 2426 ctlr->battery_desc.use_for_apm = 0; 2427 ctlr->battery_desc.name = devm_kasprintf(&hdev->dev, GFP_KERNEL, 2428 name_fmt, 2429 dev_name(&hdev->dev)); 2430 if (!ctlr->battery_desc.name) 2431 return -ENOMEM; 2432 2433 ctlr->battery = devm_power_supply_register(&hdev->dev, 2434 &ctlr->battery_desc, 2435 &supply_config); 2436 if (IS_ERR(ctlr->battery)) { 2437 ret = PTR_ERR(ctlr->battery); 2438 hid_err(hdev, "Failed to register battery; ret=%d\n", ret); 2439 return ret; 2440 } 2441 2442 return power_supply_powers(ctlr->battery, &hdev->dev); 2443} 2444 2445static int joycon_read_info(struct joycon_ctlr *ctlr) 2446{ 2447 int ret; 2448 int i; 2449 int j; 2450 struct joycon_subcmd_request req = { 0 }; 2451 struct joycon_input_report *report; 2452 2453 req.subcmd_id = JC_SUBCMD_REQ_DEV_INFO; 2454 ret = joycon_send_subcmd(ctlr, &req, 0, HZ); 2455 if (ret) { 2456 hid_err(ctlr->hdev, "Failed to get joycon info; ret=%d\n", ret); 2457 return ret; 2458 } 2459 2460 report = (struct joycon_input_report *)ctlr->input_buf; 2461 2462 for (i = 4, j = 0; j < 6; i++, j++) 2463 ctlr->mac_addr[j] = report->subcmd_reply.data[i]; 2464 2465 ctlr->mac_addr_str = devm_kasprintf(&ctlr->hdev->dev, GFP_KERNEL, 2466 "%02X:%02X:%02X:%02X:%02X:%02X", 2467 ctlr->mac_addr[0], 2468 ctlr->mac_addr[1], 2469 ctlr->mac_addr[2], 2470 ctlr->mac_addr[3], 2471 ctlr->mac_addr[4], 2472 ctlr->mac_addr[5]); 2473 if (!ctlr->mac_addr_str) 2474 return -ENOMEM; 2475 hid_info(ctlr->hdev, "controller MAC = %s\n", ctlr->mac_addr_str); 2476 2477 /* 2478 * Retrieve the type so we can distinguish the controller type 2479 * Unfortantly the hdev->product can't always be used due to a ?bug? 2480 * with the NSO Genesis controller. Over USB, it will report the 2481 * PID as 0x201E, but over bluetooth it will report the PID as 0x2017 2482 * which is the same as the NSO SNES controller. This is different from 2483 * the rest of the controllers which will report the same PID over USB 2484 * and bluetooth. 2485 */ 2486 ctlr->ctlr_type = report->subcmd_reply.data[2]; 2487 hid_dbg(ctlr->hdev, "controller type = 0x%02X\n", ctlr->ctlr_type); 2488 2489 return 0; 2490} 2491 2492static int joycon_init(struct hid_device *hdev) 2493{ 2494 struct joycon_ctlr *ctlr = hid_get_drvdata(hdev); 2495 int ret = 0; 2496 2497 mutex_lock(&ctlr->output_mutex); 2498 /* if handshake command fails, assume ble pro controller */ 2499 if (joycon_using_usb(ctlr) && !joycon_send_usb(ctlr, JC_USB_CMD_HANDSHAKE, HZ)) { 2500 hid_dbg(hdev, "detected USB controller\n"); 2501 /* set baudrate for improved latency */ 2502 ret = joycon_send_usb(ctlr, JC_USB_CMD_BAUDRATE_3M, HZ); 2503 if (ret) { 2504 hid_err(hdev, "Failed to set baudrate; ret=%d\n", ret); 2505 goto out_unlock; 2506 } 2507 /* handshake */ 2508 ret = joycon_send_usb(ctlr, JC_USB_CMD_HANDSHAKE, HZ); 2509 if (ret) { 2510 hid_err(hdev, "Failed handshake; ret=%d\n", ret); 2511 goto out_unlock; 2512 } 2513 /* 2514 * Set no timeout (to keep controller in USB mode). 2515 * This doesn't send a response, so ignore the timeout. 2516 */ 2517 joycon_send_usb(ctlr, JC_USB_CMD_NO_TIMEOUT, HZ/10); 2518 } else if (jc_type_is_chrggrip(ctlr)) { 2519 hid_err(hdev, "Failed charging grip handshake\n"); 2520 ret = -ETIMEDOUT; 2521 goto out_unlock; 2522 } 2523 2524 /* needed to retrieve the controller type */ 2525 ret = joycon_read_info(ctlr); 2526 if (ret) { 2527 hid_err(hdev, "Failed to retrieve controller info; ret=%d\n", 2528 ret); 2529 goto out_unlock; 2530 } 2531 2532 if (joycon_has_joysticks(ctlr)) { 2533 /* get controller calibration data, and parse it */ 2534 ret = joycon_request_calibration(ctlr); 2535 if (ret) { 2536 /* 2537 * We can function with default calibration, but it may be 2538 * inaccurate. Provide a warning, and continue on. 2539 */ 2540 hid_warn(hdev, "Analog stick positions may be inaccurate\n"); 2541 } 2542 } 2543 2544 if (joycon_has_imu(ctlr)) { 2545 /* get IMU calibration data, and parse it */ 2546 ret = joycon_request_imu_calibration(ctlr); 2547 if (ret) { 2548 /* 2549 * We can function with default calibration, but it may be 2550 * inaccurate. Provide a warning, and continue on. 2551 */ 2552 hid_warn(hdev, "Unable to read IMU calibration data\n"); 2553 } 2554 2555 /* Enable the IMU */ 2556 ret = joycon_enable_imu(ctlr); 2557 if (ret) { 2558 hid_err(hdev, "Failed to enable the IMU; ret=%d\n", ret); 2559 goto out_unlock; 2560 } 2561 } 2562 2563 /* Set the reporting mode to 0x30, which is the full report mode */ 2564 ret = joycon_set_report_mode(ctlr); 2565 if (ret) { 2566 hid_err(hdev, "Failed to set report mode; ret=%d\n", ret); 2567 goto out_unlock; 2568 } 2569 2570 if (joycon_has_rumble(ctlr)) { 2571 /* Enable rumble */ 2572 ret = joycon_enable_rumble(ctlr); 2573 if (ret) { 2574 hid_err(hdev, "Failed to enable rumble; ret=%d\n", ret); 2575 goto out_unlock; 2576 } 2577 } 2578 2579out_unlock: 2580 mutex_unlock(&ctlr->output_mutex); 2581 return ret; 2582} 2583 2584/* Common handler for parsing inputs */ 2585static int joycon_ctlr_read_handler(struct joycon_ctlr *ctlr, u8 *data, 2586 int size) 2587{ 2588 if (data[0] == JC_INPUT_SUBCMD_REPLY || data[0] == JC_INPUT_IMU_DATA || 2589 data[0] == JC_INPUT_MCU_DATA) { 2590 if (size >= 12) /* make sure it contains the input report */ 2591 joycon_parse_report(ctlr, 2592 (struct joycon_input_report *)data); 2593 } 2594 2595 return 0; 2596} 2597 2598static int joycon_ctlr_handle_event(struct joycon_ctlr *ctlr, u8 *data, 2599 int size) 2600{ 2601 int ret = 0; 2602 bool match = false; 2603 struct joycon_input_report *report; 2604 2605 if (unlikely(mutex_is_locked(&ctlr->output_mutex)) && 2606 ctlr->msg_type != JOYCON_MSG_TYPE_NONE) { 2607 switch (ctlr->msg_type) { 2608 case JOYCON_MSG_TYPE_USB: 2609 if (size < 2) 2610 break; 2611 if (data[0] == JC_INPUT_USB_RESPONSE && 2612 data[1] == ctlr->usb_ack_match) 2613 match = true; 2614 break; 2615 case JOYCON_MSG_TYPE_SUBCMD: 2616 if (size < sizeof(struct joycon_input_report) || 2617 data[0] != JC_INPUT_SUBCMD_REPLY) 2618 break; 2619 report = (struct joycon_input_report *)data; 2620 if (report->subcmd_reply.id == ctlr->subcmd_ack_match) 2621 match = true; 2622 break; 2623 default: 2624 break; 2625 } 2626 2627 if (match) { 2628 memcpy(ctlr->input_buf, data, 2629 min(size, (int)JC_MAX_RESP_SIZE)); 2630 ctlr->msg_type = JOYCON_MSG_TYPE_NONE; 2631 ctlr->received_resp = true; 2632 wake_up(&ctlr->wait); 2633 2634 /* This message has been handled */ 2635 return 1; 2636 } 2637 } 2638 2639 if (ctlr->ctlr_state == JOYCON_CTLR_STATE_READ) 2640 ret = joycon_ctlr_read_handler(ctlr, data, size); 2641 2642 return ret; 2643} 2644 2645static int nintendo_hid_event(struct hid_device *hdev, 2646 struct hid_report *report, u8 *raw_data, int size) 2647{ 2648 struct joycon_ctlr *ctlr = hid_get_drvdata(hdev); 2649 2650 if (size < 1) 2651 return -EINVAL; 2652 2653 return joycon_ctlr_handle_event(ctlr, raw_data, size); 2654} 2655 2656static int nintendo_hid_probe(struct hid_device *hdev, 2657 const struct hid_device_id *id) 2658{ 2659 int ret; 2660 struct joycon_ctlr *ctlr; 2661 2662 hid_dbg(hdev, "probe - start\n"); 2663 2664 ctlr = devm_kzalloc(&hdev->dev, sizeof(*ctlr), GFP_KERNEL); 2665 if (!ctlr) { 2666 ret = -ENOMEM; 2667 goto err; 2668 } 2669 2670 ctlr->hdev = hdev; 2671 ctlr->ctlr_state = JOYCON_CTLR_STATE_INIT; 2672 ctlr->rumble_queue_head = 0; 2673 ctlr->rumble_queue_tail = 0; 2674 hid_set_drvdata(hdev, ctlr); 2675 mutex_init(&ctlr->output_mutex); 2676 init_waitqueue_head(&ctlr->wait); 2677 spin_lock_init(&ctlr->lock); 2678 ctlr->rumble_queue = alloc_workqueue("hid-nintendo-rumble_wq", 2679 WQ_FREEZABLE | WQ_MEM_RECLAIM, 0); 2680 if (!ctlr->rumble_queue) { 2681 ret = -ENOMEM; 2682 goto err; 2683 } 2684 INIT_WORK(&ctlr->rumble_worker, joycon_rumble_worker); 2685 2686 ret = hid_parse(hdev); 2687 if (ret) { 2688 hid_err(hdev, "HID parse failed\n"); 2689 goto err_wq; 2690 } 2691 2692 /* 2693 * Patch the hw version of pro controller/joycons, so applications can 2694 * distinguish between the default HID mappings and the mappings defined 2695 * by the Linux game controller spec. This is important for the SDL2 2696 * library, which has a game controller database, which uses device ids 2697 * in combination with version as a key. 2698 */ 2699 hdev->version |= 0x8000; 2700 2701 ret = hid_hw_start(hdev, HID_CONNECT_HIDRAW); 2702 if (ret) { 2703 hid_err(hdev, "HW start failed\n"); 2704 goto err_wq; 2705 } 2706 2707 ret = hid_hw_open(hdev); 2708 if (ret) { 2709 hid_err(hdev, "cannot start hardware I/O\n"); 2710 goto err_stop; 2711 } 2712 2713 hid_device_io_start(hdev); 2714 2715 ret = joycon_init(hdev); 2716 if (ret) { 2717 hid_err(hdev, "Failed to initialize controller; ret=%d\n", ret); 2718 goto err_close; 2719 } 2720 2721 /* Initialize the leds */ 2722 ret = joycon_leds_create(ctlr); 2723 if (ret) { 2724 hid_err(hdev, "Failed to create leds; ret=%d\n", ret); 2725 goto err_close; 2726 } 2727 2728 /* Initialize the battery power supply */ 2729 ret = joycon_power_supply_create(ctlr); 2730 if (ret) { 2731 hid_err(hdev, "Failed to create power_supply; ret=%d\n", ret); 2732 goto err_close; 2733 } 2734 2735 ret = joycon_input_create(ctlr); 2736 if (ret) { 2737 hid_err(hdev, "Failed to create input device; ret=%d\n", ret); 2738 goto err_close; 2739 } 2740 2741 ctlr->ctlr_state = JOYCON_CTLR_STATE_READ; 2742 2743 hid_dbg(hdev, "probe - success\n"); 2744 return 0; 2745 2746err_close: 2747 hid_hw_close(hdev); 2748err_stop: 2749 hid_hw_stop(hdev); 2750err_wq: 2751 destroy_workqueue(ctlr->rumble_queue); 2752err: 2753 hid_err(hdev, "probe - fail = %d\n", ret); 2754 return ret; 2755} 2756 2757static void nintendo_hid_remove(struct hid_device *hdev) 2758{ 2759 struct joycon_ctlr *ctlr = hid_get_drvdata(hdev); 2760 unsigned long flags; 2761 2762 hid_dbg(hdev, "remove\n"); 2763 2764 /* Prevent further attempts at sending subcommands. */ 2765 spin_lock_irqsave(&ctlr->lock, flags); 2766 ctlr->ctlr_state = JOYCON_CTLR_STATE_REMOVED; 2767 spin_unlock_irqrestore(&ctlr->lock, flags); 2768 2769 destroy_workqueue(ctlr->rumble_queue); 2770 2771 hid_hw_close(hdev); 2772 hid_hw_stop(hdev); 2773} 2774 2775#ifdef CONFIG_PM 2776 2777static int nintendo_hid_resume(struct hid_device *hdev) 2778{ 2779 int ret = joycon_init(hdev); 2780 2781 if (ret) 2782 hid_err(hdev, "Failed to restore controller after resume"); 2783 2784 return ret; 2785} 2786 2787#endif 2788 2789static const struct hid_device_id nintendo_hid_devices[] = { 2790 { HID_USB_DEVICE(USB_VENDOR_ID_NINTENDO, 2791 USB_DEVICE_ID_NINTENDO_PROCON) }, 2792 { HID_USB_DEVICE(USB_VENDOR_ID_NINTENDO, 2793 USB_DEVICE_ID_NINTENDO_SNESCON) }, 2794 { HID_USB_DEVICE(USB_VENDOR_ID_NINTENDO, 2795 USB_DEVICE_ID_NINTENDO_GENCON) }, 2796 { HID_USB_DEVICE(USB_VENDOR_ID_NINTENDO, 2797 USB_DEVICE_ID_NINTENDO_N64CON) }, 2798 { HID_BLUETOOTH_DEVICE(USB_VENDOR_ID_NINTENDO, 2799 USB_DEVICE_ID_NINTENDO_PROCON) }, 2800 { HID_USB_DEVICE(USB_VENDOR_ID_NINTENDO, 2801 USB_DEVICE_ID_NINTENDO_CHRGGRIP) }, 2802 { HID_BLUETOOTH_DEVICE(USB_VENDOR_ID_NINTENDO, 2803 USB_DEVICE_ID_NINTENDO_JOYCONL) }, 2804 { HID_BLUETOOTH_DEVICE(USB_VENDOR_ID_NINTENDO, 2805 USB_DEVICE_ID_NINTENDO_JOYCONR) }, 2806 { HID_BLUETOOTH_DEVICE(USB_VENDOR_ID_NINTENDO, 2807 USB_DEVICE_ID_NINTENDO_SNESCON) }, 2808 { HID_BLUETOOTH_DEVICE(USB_VENDOR_ID_NINTENDO, 2809 USB_DEVICE_ID_NINTENDO_GENCON) }, 2810 { HID_BLUETOOTH_DEVICE(USB_VENDOR_ID_NINTENDO, 2811 USB_DEVICE_ID_NINTENDO_N64CON) }, 2812 { } 2813}; 2814MODULE_DEVICE_TABLE(hid, nintendo_hid_devices); 2815 2816static struct hid_driver nintendo_hid_driver = { 2817 .name = "nintendo", 2818 .id_table = nintendo_hid_devices, 2819 .probe = nintendo_hid_probe, 2820 .remove = nintendo_hid_remove, 2821 .raw_event = nintendo_hid_event, 2822 2823#ifdef CONFIG_PM 2824 .resume = nintendo_hid_resume, 2825#endif 2826}; 2827module_hid_driver(nintendo_hid_driver); 2828 2829MODULE_LICENSE("GPL"); 2830MODULE_AUTHOR("Ryan McClelland <rymcclel@gmail.com>"); 2831MODULE_AUTHOR("Emily Strickland <linux@emily.st>"); 2832MODULE_AUTHOR("Daniel J. Ogorchock <djogorchock@gmail.com>"); 2833MODULE_DESCRIPTION("Driver for Nintendo Switch Controllers"); 2834