1/* SPDX-License-Identifier: GPL-2.0 */ 2 3/* include/asm-m68knommu/MC68VZ328.h: 'VZ328 control registers 4 * 5 * Copyright (c) 2000-2001 Lineo Inc. <www.lineo.com> 6 * Copyright (c) 2000-2001 Lineo Canada Corp. <www.lineo.ca> 7 * Copyright (C) 1999 Vladimir Gurevich <vgurevic@cisco.com> 8 * Bare & Hare Software, Inc. 9 * Based on include/asm-m68knommu/MC68332.h 10 * Copyright (C) 1998 Kenneth Albanowski <kjahds@kjahds.com>, 11 * The Silver Hammer Group, Ltd. 12 * 13 * M68VZ328 fixes by Evan Stawnyczy <evan@lineo.com> 14 * vz multiport fixes by Michael Leslie <mleslie@lineo.com> 15 */ 16 17#ifndef _MC68VZ328_H_ 18#define _MC68VZ328_H_ 19 20#define BYTE_REF(addr) (*((volatile unsigned char*)addr)) 21#define WORD_REF(addr) (*((volatile unsigned short*)addr)) 22#define LONG_REF(addr) (*((volatile unsigned long*)addr)) 23 24#define PUT_FIELD(field, val) (((val) << field##_SHIFT) & field##_MASK) 25#define GET_FIELD(reg, field) (((reg) & field##_MASK) >> field##_SHIFT) 26 27/********** 28 * 29 * 0xFFFFF0xx -- System Control 30 * 31 **********/ 32 33/* 34 * System Control Register (SCR) 35 */ 36#define SCR_ADDR 0xfffff000 37#define SCR BYTE_REF(SCR_ADDR) 38 39#define SCR_WDTH8 0x01 /* 8-Bit Width Select */ 40#define SCR_DMAP 0x04 /* Double Map */ 41#define SCR_SO 0x08 /* Supervisor Only */ 42#define SCR_BETEN 0x10 /* Bus-Error Time-Out Enable */ 43#define SCR_PRV 0x20 /* Privilege Violation */ 44#define SCR_WPV 0x40 /* Write Protect Violation */ 45#define SCR_BETO 0x80 /* Bus-Error TimeOut */ 46 47/* 48 * Silicon ID Register (Mask Revision Register (MRR) for '328 Compatibility) 49 */ 50#define MRR_ADDR 0xfffff004 51#define MRR LONG_REF(MRR_ADDR) 52 53/********** 54 * 55 * 0xFFFFF1xx -- Chip-Select logic 56 * 57 **********/ 58 59/* 60 * Chip Select Group Base Registers 61 */ 62#define CSGBA_ADDR 0xfffff100 63#define CSGBB_ADDR 0xfffff102 64 65#define CSGBC_ADDR 0xfffff104 66#define CSGBD_ADDR 0xfffff106 67 68#define CSGBA WORD_REF(CSGBA_ADDR) 69#define CSGBB WORD_REF(CSGBB_ADDR) 70#define CSGBC WORD_REF(CSGBC_ADDR) 71#define CSGBD WORD_REF(CSGBD_ADDR) 72 73/* 74 * Chip Select Registers 75 */ 76#define CSA_ADDR 0xfffff110 77#define CSB_ADDR 0xfffff112 78#define CSC_ADDR 0xfffff114 79#define CSD_ADDR 0xfffff116 80 81#define CSA WORD_REF(CSA_ADDR) 82#define CSB WORD_REF(CSB_ADDR) 83#define CSC WORD_REF(CSC_ADDR) 84#define CSD WORD_REF(CSD_ADDR) 85 86#define CSA_EN 0x0001 /* Chip-Select Enable */ 87#define CSA_SIZ_MASK 0x000e /* Chip-Select Size */ 88#define CSA_SIZ_SHIFT 1 89#define CSA_WS_MASK 0x0070 /* Wait State */ 90#define CSA_WS_SHIFT 4 91#define CSA_BSW 0x0080 /* Data Bus Width */ 92#define CSA_FLASH 0x0100 /* FLASH Memory Support */ 93#define CSA_RO 0x8000 /* Read-Only */ 94 95#define CSB_EN 0x0001 /* Chip-Select Enable */ 96#define CSB_SIZ_MASK 0x000e /* Chip-Select Size */ 97#define CSB_SIZ_SHIFT 1 98#define CSB_WS_MASK 0x0070 /* Wait State */ 99#define CSB_WS_SHIFT 4 100#define CSB_BSW 0x0080 /* Data Bus Width */ 101#define CSB_FLASH 0x0100 /* FLASH Memory Support */ 102#define CSB_UPSIZ_MASK 0x1800 /* Unprotected memory block size */ 103#define CSB_UPSIZ_SHIFT 11 104#define CSB_ROP 0x2000 /* Readonly if protected */ 105#define CSB_SOP 0x4000 /* Supervisor only if protected */ 106#define CSB_RO 0x8000 /* Read-Only */ 107 108#define CSC_EN 0x0001 /* Chip-Select Enable */ 109#define CSC_SIZ_MASK 0x000e /* Chip-Select Size */ 110#define CSC_SIZ_SHIFT 1 111#define CSC_WS_MASK 0x0070 /* Wait State */ 112#define CSC_WS_SHIFT 4 113#define CSC_BSW 0x0080 /* Data Bus Width */ 114#define CSC_FLASH 0x0100 /* FLASH Memory Support */ 115#define CSC_UPSIZ_MASK 0x1800 /* Unprotected memory block size */ 116#define CSC_UPSIZ_SHIFT 11 117#define CSC_ROP 0x2000 /* Readonly if protected */ 118#define CSC_SOP 0x4000 /* Supervisor only if protected */ 119#define CSC_RO 0x8000 /* Read-Only */ 120 121#define CSD_EN 0x0001 /* Chip-Select Enable */ 122#define CSD_SIZ_MASK 0x000e /* Chip-Select Size */ 123#define CSD_SIZ_SHIFT 1 124#define CSD_WS_MASK 0x0070 /* Wait State */ 125#define CSD_WS_SHIFT 4 126#define CSD_BSW 0x0080 /* Data Bus Width */ 127#define CSD_FLASH 0x0100 /* FLASH Memory Support */ 128#define CSD_DRAM 0x0200 /* Dram Selection */ 129#define CSD_COMB 0x0400 /* Combining */ 130#define CSD_UPSIZ_MASK 0x1800 /* Unprotected memory block size */ 131#define CSD_UPSIZ_SHIFT 11 132#define CSD_ROP 0x2000 /* Readonly if protected */ 133#define CSD_SOP 0x4000 /* Supervisor only if protected */ 134#define CSD_RO 0x8000 /* Read-Only */ 135 136/* 137 * Emulation Chip-Select Register 138 */ 139#define EMUCS_ADDR 0xfffff118 140#define EMUCS WORD_REF(EMUCS_ADDR) 141 142#define EMUCS_WS_MASK 0x0070 143#define EMUCS_WS_SHIFT 4 144 145/********** 146 * 147 * 0xFFFFF2xx -- Phase Locked Loop (PLL) & Power Control 148 * 149 **********/ 150 151/* 152 * PLL Control Register 153 */ 154#define PLLCR_ADDR 0xfffff200 155#define PLLCR WORD_REF(PLLCR_ADDR) 156 157#define PLLCR_DISPLL 0x0008 /* Disable PLL */ 158#define PLLCR_CLKEN 0x0010 /* Clock (CLKO pin) enable */ 159#define PLLCR_PRESC 0x0020 /* VCO prescaler */ 160#define PLLCR_SYSCLK_SEL_MASK 0x0700 /* System Clock Selection */ 161#define PLLCR_SYSCLK_SEL_SHIFT 8 162#define PLLCR_LCDCLK_SEL_MASK 0x3800 /* LCD Clock Selection */ 163#define PLLCR_LCDCLK_SEL_SHIFT 11 164 165/* '328-compatible definitions */ 166#define PLLCR_PIXCLK_SEL_MASK PLLCR_LCDCLK_SEL_MASK 167#define PLLCR_PIXCLK_SEL_SHIFT PLLCR_LCDCLK_SEL_SHIFT 168 169/* 170 * PLL Frequency Select Register 171 */ 172#define PLLFSR_ADDR 0xfffff202 173#define PLLFSR WORD_REF(PLLFSR_ADDR) 174 175#define PLLFSR_PC_MASK 0x00ff /* P Count */ 176#define PLLFSR_PC_SHIFT 0 177#define PLLFSR_QC_MASK 0x0f00 /* Q Count */ 178#define PLLFSR_QC_SHIFT 8 179#define PLLFSR_PROT 0x4000 /* Protect P & Q */ 180#define PLLFSR_CLK32 0x8000 /* Clock 32 (kHz) */ 181 182/* 183 * Power Control Register 184 */ 185#define PCTRL_ADDR 0xfffff207 186#define PCTRL BYTE_REF(PCTRL_ADDR) 187 188#define PCTRL_WIDTH_MASK 0x1f /* CPU Clock bursts width */ 189#define PCTRL_WIDTH_SHIFT 0 190#define PCTRL_PCEN 0x80 /* Power Control Enable */ 191 192/********** 193 * 194 * 0xFFFFF3xx -- Interrupt Controller 195 * 196 **********/ 197 198/* 199 * Interrupt Vector Register 200 */ 201#define IVR_ADDR 0xfffff300 202#define IVR BYTE_REF(IVR_ADDR) 203 204#define IVR_VECTOR_MASK 0xF8 205 206/* 207 * Interrupt control Register 208 */ 209#define ICR_ADDR 0xfffff302 210#define ICR WORD_REF(ICR_ADDR) 211 212#define ICR_POL5 0x0080 /* Polarity Control for IRQ5 */ 213#define ICR_ET6 0x0100 /* Edge Trigger Select for IRQ6 */ 214#define ICR_ET3 0x0200 /* Edge Trigger Select for IRQ3 */ 215#define ICR_ET2 0x0400 /* Edge Trigger Select for IRQ2 */ 216#define ICR_ET1 0x0800 /* Edge Trigger Select for IRQ1 */ 217#define ICR_POL6 0x1000 /* Polarity Control for IRQ6 */ 218#define ICR_POL3 0x2000 /* Polarity Control for IRQ3 */ 219#define ICR_POL2 0x4000 /* Polarity Control for IRQ2 */ 220#define ICR_POL1 0x8000 /* Polarity Control for IRQ1 */ 221 222/* 223 * Interrupt Mask Register 224 */ 225#define IMR_ADDR 0xfffff304 226#define IMR LONG_REF(IMR_ADDR) 227 228/* 229 * Define the names for bit positions first. This is useful for 230 * request_irq 231 */ 232#define SPI2_IRQ_NUM 0 /* SPI 2 interrupt */ 233#define TMR_IRQ_NUM 1 /* Timer 1 interrupt */ 234#define UART1_IRQ_NUM 2 /* UART 1 interrupt */ 235#define WDT_IRQ_NUM 3 /* Watchdog Timer interrupt */ 236#define RTC_IRQ_NUM 4 /* RTC interrupt */ 237#define TMR2_IRQ_NUM 5 /* Timer 2 interrupt */ 238#define KB_IRQ_NUM 6 /* Keyboard Interrupt */ 239#define PWM1_IRQ_NUM 7 /* Pulse-Width Modulator 1 int. */ 240#define INT0_IRQ_NUM 8 /* External INT0 */ 241#define INT1_IRQ_NUM 9 /* External INT1 */ 242#define INT2_IRQ_NUM 10 /* External INT2 */ 243#define INT3_IRQ_NUM 11 /* External INT3 */ 244#define UART2_IRQ_NUM 12 /* UART 2 interrupt */ 245#define PWM2_IRQ_NUM 13 /* Pulse-Width Modulator 1 int. */ 246#define IRQ1_IRQ_NUM 16 /* IRQ1 */ 247#define IRQ2_IRQ_NUM 17 /* IRQ2 */ 248#define IRQ3_IRQ_NUM 18 /* IRQ3 */ 249#define IRQ6_IRQ_NUM 19 /* IRQ6 */ 250#define IRQ5_IRQ_NUM 20 /* IRQ5 */ 251#define SPI1_IRQ_NUM 21 /* SPI 1 interrupt */ 252#define SAM_IRQ_NUM 22 /* Sampling Timer for RTC */ 253#define EMIQ_IRQ_NUM 23 /* Emulator Interrupt */ 254 255#define SPI_IRQ_NUM SPI2_IRQ_NUM 256 257/* '328-compatible definitions */ 258#define SPIM_IRQ_NUM SPI_IRQ_NUM 259#define TMR1_IRQ_NUM TMR_IRQ_NUM 260#define UART_IRQ_NUM UART1_IRQ_NUM 261 262/* 263 * Here go the bitmasks themselves 264 */ 265#define IMR_MSPI (1 << SPI_IRQ_NUM) /* Mask SPI interrupt */ 266#define IMR_MTMR (1 << TMR_IRQ_NUM) /* Mask Timer interrupt */ 267#define IMR_MUART (1 << UART_IRQ_NUM) /* Mask UART interrupt */ 268#define IMR_MWDT (1 << WDT_IRQ_NUM) /* Mask Watchdog Timer interrupt */ 269#define IMR_MRTC (1 << RTC_IRQ_NUM) /* Mask RTC interrupt */ 270#define IMR_MKB (1 << KB_IRQ_NUM) /* Mask Keyboard Interrupt */ 271#define IMR_MPWM (1 << PWM_IRQ_NUM) /* Mask Pulse-Width Modulator int. */ 272#define IMR_MINT0 (1 << INT0_IRQ_NUM) /* Mask External INT0 */ 273#define IMR_MINT1 (1 << INT1_IRQ_NUM) /* Mask External INT1 */ 274#define IMR_MINT2 (1 << INT2_IRQ_NUM) /* Mask External INT2 */ 275#define IMR_MINT3 (1 << INT3_IRQ_NUM) /* Mask External INT3 */ 276#define IMR_MIRQ1 (1 << IRQ1_IRQ_NUM) /* Mask IRQ1 */ 277#define IMR_MIRQ2 (1 << IRQ2_IRQ_NUM) /* Mask IRQ2 */ 278#define IMR_MIRQ3 (1 << IRQ3_IRQ_NUM) /* Mask IRQ3 */ 279#define IMR_MIRQ6 (1 << IRQ6_IRQ_NUM) /* Mask IRQ6 */ 280#define IMR_MIRQ5 (1 << IRQ5_IRQ_NUM) /* Mask IRQ5 */ 281#define IMR_MSAM (1 << SAM_IRQ_NUM) /* Mask Sampling Timer for RTC */ 282#define IMR_MEMIQ (1 << EMIQ_IRQ_NUM) /* Mask Emulator Interrupt */ 283 284/* '328-compatible definitions */ 285#define IMR_MSPIM IMR_MSPI 286#define IMR_MTMR1 IMR_MTMR 287 288/* 289 * Interrupt Status Register 290 */ 291#define ISR_ADDR 0xfffff30c 292#define ISR LONG_REF(ISR_ADDR) 293 294#define ISR_SPI (1 << SPI_IRQ_NUM) /* SPI interrupt */ 295#define ISR_TMR (1 << TMR_IRQ_NUM) /* Timer interrupt */ 296#define ISR_UART (1 << UART_IRQ_NUM) /* UART interrupt */ 297#define ISR_WDT (1 << WDT_IRQ_NUM) /* Watchdog Timer interrupt */ 298#define ISR_RTC (1 << RTC_IRQ_NUM) /* RTC interrupt */ 299#define ISR_KB (1 << KB_IRQ_NUM) /* Keyboard Interrupt */ 300#define ISR_PWM (1 << PWM_IRQ_NUM) /* Pulse-Width Modulator interrupt */ 301#define ISR_INT0 (1 << INT0_IRQ_NUM) /* External INT0 */ 302#define ISR_INT1 (1 << INT1_IRQ_NUM) /* External INT1 */ 303#define ISR_INT2 (1 << INT2_IRQ_NUM) /* External INT2 */ 304#define ISR_INT3 (1 << INT3_IRQ_NUM) /* External INT3 */ 305#define ISR_IRQ1 (1 << IRQ1_IRQ_NUM) /* IRQ1 */ 306#define ISR_IRQ2 (1 << IRQ2_IRQ_NUM) /* IRQ2 */ 307#define ISR_IRQ3 (1 << IRQ3_IRQ_NUM) /* IRQ3 */ 308#define ISR_IRQ6 (1 << IRQ6_IRQ_NUM) /* IRQ6 */ 309#define ISR_IRQ5 (1 << IRQ5_IRQ_NUM) /* IRQ5 */ 310#define ISR_SAM (1 << SAM_IRQ_NUM) /* Sampling Timer for RTC */ 311#define ISR_EMIQ (1 << EMIQ_IRQ_NUM) /* Emulator Interrupt */ 312 313/* '328-compatible definitions */ 314#define ISR_SPIM ISR_SPI 315#define ISR_TMR1 ISR_TMR 316 317/* 318 * Interrupt Pending Register 319 */ 320#define IPR_ADDR 0xfffff30c 321#define IPR LONG_REF(IPR_ADDR) 322 323#define IPR_SPI (1 << SPI_IRQ_NUM) /* SPI interrupt */ 324#define IPR_TMR (1 << TMR_IRQ_NUM) /* Timer interrupt */ 325#define IPR_UART (1 << UART_IRQ_NUM) /* UART interrupt */ 326#define IPR_WDT (1 << WDT_IRQ_NUM) /* Watchdog Timer interrupt */ 327#define IPR_RTC (1 << RTC_IRQ_NUM) /* RTC interrupt */ 328#define IPR_KB (1 << KB_IRQ_NUM) /* Keyboard Interrupt */ 329#define IPR_PWM (1 << PWM_IRQ_NUM) /* Pulse-Width Modulator interrupt */ 330#define IPR_INT0 (1 << INT0_IRQ_NUM) /* External INT0 */ 331#define IPR_INT1 (1 << INT1_IRQ_NUM) /* External INT1 */ 332#define IPR_INT2 (1 << INT2_IRQ_NUM) /* External INT2 */ 333#define IPR_INT3 (1 << INT3_IRQ_NUM) /* External INT3 */ 334#define IPR_IRQ1 (1 << IRQ1_IRQ_NUM) /* IRQ1 */ 335#define IPR_IRQ2 (1 << IRQ2_IRQ_NUM) /* IRQ2 */ 336#define IPR_IRQ3 (1 << IRQ3_IRQ_NUM) /* IRQ3 */ 337#define IPR_IRQ6 (1 << IRQ6_IRQ_NUM) /* IRQ6 */ 338#define IPR_IRQ5 (1 << IRQ5_IRQ_NUM) /* IRQ5 */ 339#define IPR_SAM (1 << SAM_IRQ_NUM) /* Sampling Timer for RTC */ 340#define IPR_EMIQ (1 << EMIQ_IRQ_NUM) /* Emulator Interrupt */ 341 342/* '328-compatible definitions */ 343#define IPR_SPIM IPR_SPI 344#define IPR_TMR1 IPR_TMR 345 346/********** 347 * 348 * 0xFFFFF4xx -- Parallel Ports 349 * 350 **********/ 351 352/* 353 * Port A 354 */ 355#define PADIR_ADDR 0xfffff400 /* Port A direction reg */ 356#define PADATA_ADDR 0xfffff401 /* Port A data register */ 357#define PAPUEN_ADDR 0xfffff402 /* Port A Pull-Up enable reg */ 358 359#define PADIR BYTE_REF(PADIR_ADDR) 360#define PADATA BYTE_REF(PADATA_ADDR) 361#define PAPUEN BYTE_REF(PAPUEN_ADDR) 362 363#define PA(x) (1 << (x)) 364 365/* 366 * Port B 367 */ 368#define PBDIR_ADDR 0xfffff408 /* Port B direction reg */ 369#define PBDATA_ADDR 0xfffff409 /* Port B data register */ 370#define PBPUEN_ADDR 0xfffff40a /* Port B Pull-Up enable reg */ 371#define PBSEL_ADDR 0xfffff40b /* Port B Select Register */ 372 373#define PBDIR BYTE_REF(PBDIR_ADDR) 374#define PBDATA BYTE_REF(PBDATA_ADDR) 375#define PBPUEN BYTE_REF(PBPUEN_ADDR) 376#define PBSEL BYTE_REF(PBSEL_ADDR) 377 378#define PB(x) (1 << (x)) 379 380#define PB_CSB0 0x01 /* Use CSB0 as PB[0] */ 381#define PB_CSB1 0x02 /* Use CSB1 as PB[1] */ 382#define PB_CSC0_RAS0 0x04 /* Use CSC0/RAS0 as PB[2] */ 383#define PB_CSC1_RAS1 0x08 /* Use CSC1/RAS1 as PB[3] */ 384#define PB_CSD0_CAS0 0x10 /* Use CSD0/CAS0 as PB[4] */ 385#define PB_CSD1_CAS1 0x20 /* Use CSD1/CAS1 as PB[5] */ 386#define PB_TIN_TOUT 0x40 /* Use TIN/TOUT as PB[6] */ 387#define PB_PWMO 0x80 /* Use PWMO as PB[7] */ 388 389/* 390 * Port C 391 */ 392#define PCDIR_ADDR 0xfffff410 /* Port C direction reg */ 393#define PCDATA_ADDR 0xfffff411 /* Port C data register */ 394#define PCPDEN_ADDR 0xfffff412 /* Port C Pull-Down enb. reg */ 395#define PCSEL_ADDR 0xfffff413 /* Port C Select Register */ 396 397#define PCDIR BYTE_REF(PCDIR_ADDR) 398#define PCDATA BYTE_REF(PCDATA_ADDR) 399#define PCPDEN BYTE_REF(PCPDEN_ADDR) 400#define PCSEL BYTE_REF(PCSEL_ADDR) 401 402#define PC(x) (1 << (x)) 403 404#define PC_LD0 0x01 /* Use LD0 as PC[0] */ 405#define PC_LD1 0x02 /* Use LD1 as PC[1] */ 406#define PC_LD2 0x04 /* Use LD2 as PC[2] */ 407#define PC_LD3 0x08 /* Use LD3 as PC[3] */ 408#define PC_LFLM 0x10 /* Use LFLM as PC[4] */ 409#define PC_LLP 0x20 /* Use LLP as PC[5] */ 410#define PC_LCLK 0x40 /* Use LCLK as PC[6] */ 411#define PC_LACD 0x80 /* Use LACD as PC[7] */ 412 413/* 414 * Port D 415 */ 416#define PDDIR_ADDR 0xfffff418 /* Port D direction reg */ 417#define PDDATA_ADDR 0xfffff419 /* Port D data register */ 418#define PDPUEN_ADDR 0xfffff41a /* Port D Pull-Up enable reg */ 419#define PDSEL_ADDR 0xfffff41b /* Port D Select Register */ 420#define PDPOL_ADDR 0xfffff41c /* Port D Polarity Register */ 421#define PDIRQEN_ADDR 0xfffff41d /* Port D IRQ enable register */ 422#define PDKBEN_ADDR 0xfffff41e /* Port D Keyboard Enable reg */ 423#define PDIQEG_ADDR 0xfffff41f /* Port D IRQ Edge Register */ 424 425#define PDDIR BYTE_REF(PDDIR_ADDR) 426#define PDDATA BYTE_REF(PDDATA_ADDR) 427#define PDPUEN BYTE_REF(PDPUEN_ADDR) 428#define PDSEL BYTE_REF(PDSEL_ADDR) 429#define PDPOL BYTE_REF(PDPOL_ADDR) 430#define PDIRQEN BYTE_REF(PDIRQEN_ADDR) 431#define PDKBEN BYTE_REF(PDKBEN_ADDR) 432#define PDIQEG BYTE_REF(PDIQEG_ADDR) 433 434#define PD(x) (1 << (x)) 435 436#define PD_INT0 0x01 /* Use INT0 as PD[0] */ 437#define PD_INT1 0x02 /* Use INT1 as PD[1] */ 438#define PD_INT2 0x04 /* Use INT2 as PD[2] */ 439#define PD_INT3 0x08 /* Use INT3 as PD[3] */ 440#define PD_IRQ1 0x10 /* Use IRQ1 as PD[4] */ 441#define PD_IRQ2 0x20 /* Use IRQ2 as PD[5] */ 442#define PD_IRQ3 0x40 /* Use IRQ3 as PD[6] */ 443#define PD_IRQ6 0x80 /* Use IRQ6 as PD[7] */ 444 445/* 446 * Port E 447 */ 448#define PEDIR_ADDR 0xfffff420 /* Port E direction reg */ 449#define PEDATA_ADDR 0xfffff421 /* Port E data register */ 450#define PEPUEN_ADDR 0xfffff422 /* Port E Pull-Up enable reg */ 451#define PESEL_ADDR 0xfffff423 /* Port E Select Register */ 452 453#define PEDIR BYTE_REF(PEDIR_ADDR) 454#define PEDATA BYTE_REF(PEDATA_ADDR) 455#define PEPUEN BYTE_REF(PEPUEN_ADDR) 456#define PESEL BYTE_REF(PESEL_ADDR) 457 458#define PE(x) (1 << (x)) 459 460#define PE_SPMTXD 0x01 /* Use SPMTXD as PE[0] */ 461#define PE_SPMRXD 0x02 /* Use SPMRXD as PE[1] */ 462#define PE_SPMCLK 0x04 /* Use SPMCLK as PE[2] */ 463#define PE_DWE 0x08 /* Use DWE as PE[3] */ 464#define PE_RXD 0x10 /* Use RXD as PE[4] */ 465#define PE_TXD 0x20 /* Use TXD as PE[5] */ 466#define PE_RTS 0x40 /* Use RTS as PE[6] */ 467#define PE_CTS 0x80 /* Use CTS as PE[7] */ 468 469/* 470 * Port F 471 */ 472#define PFDIR_ADDR 0xfffff428 /* Port F direction reg */ 473#define PFDATA_ADDR 0xfffff429 /* Port F data register */ 474#define PFPUEN_ADDR 0xfffff42a /* Port F Pull-Up enable reg */ 475#define PFSEL_ADDR 0xfffff42b /* Port F Select Register */ 476 477#define PFDIR BYTE_REF(PFDIR_ADDR) 478#define PFDATA BYTE_REF(PFDATA_ADDR) 479#define PFPUEN BYTE_REF(PFPUEN_ADDR) 480#define PFSEL BYTE_REF(PFSEL_ADDR) 481 482#define PF(x) (1 << (x)) 483 484#define PF_LCONTRAST 0x01 /* Use LCONTRAST as PF[0] */ 485#define PF_IRQ5 0x02 /* Use IRQ5 as PF[1] */ 486#define PF_CLKO 0x04 /* Use CLKO as PF[2] */ 487#define PF_A20 0x08 /* Use A20 as PF[3] */ 488#define PF_A21 0x10 /* Use A21 as PF[4] */ 489#define PF_A22 0x20 /* Use A22 as PF[5] */ 490#define PF_A23 0x40 /* Use A23 as PF[6] */ 491#define PF_CSA1 0x80 /* Use CSA1 as PF[7] */ 492 493/* 494 * Port G 495 */ 496#define PGDIR_ADDR 0xfffff430 /* Port G direction reg */ 497#define PGDATA_ADDR 0xfffff431 /* Port G data register */ 498#define PGPUEN_ADDR 0xfffff432 /* Port G Pull-Up enable reg */ 499#define PGSEL_ADDR 0xfffff433 /* Port G Select Register */ 500 501#define PGDIR BYTE_REF(PGDIR_ADDR) 502#define PGDATA BYTE_REF(PGDATA_ADDR) 503#define PGPUEN BYTE_REF(PGPUEN_ADDR) 504#define PGSEL BYTE_REF(PGSEL_ADDR) 505 506#define PG(x) (1 << (x)) 507 508#define PG_BUSW_DTACK 0x01 /* Use BUSW/DTACK as PG[0] */ 509#define PG_A0 0x02 /* Use A0 as PG[1] */ 510#define PG_EMUIRQ 0x04 /* Use EMUIRQ as PG[2] */ 511#define PG_HIZ_P_D 0x08 /* Use HIZ/P/D as PG[3] */ 512#define PG_EMUCS 0x10 /* Use EMUCS as PG[4] */ 513#define PG_EMUBRK 0x20 /* Use EMUBRK as PG[5] */ 514 515/* 516 * Port J 517 */ 518#define PJDIR_ADDR 0xfffff438 /* Port J direction reg */ 519#define PJDATA_ADDR 0xfffff439 /* Port J data register */ 520#define PJPUEN_ADDR 0xfffff43A /* Port J Pull-Up enb. reg */ 521#define PJSEL_ADDR 0xfffff43B /* Port J Select Register */ 522 523#define PJDIR BYTE_REF(PJDIR_ADDR) 524#define PJDATA BYTE_REF(PJDATA_ADDR) 525#define PJPUEN BYTE_REF(PJPUEN_ADDR) 526#define PJSEL BYTE_REF(PJSEL_ADDR) 527 528#define PJ(x) (1 << (x)) 529 530/* 531 * Port K 532 */ 533#define PKDIR_ADDR 0xfffff440 /* Port K direction reg */ 534#define PKDATA_ADDR 0xfffff441 /* Port K data register */ 535#define PKPUEN_ADDR 0xfffff442 /* Port K Pull-Up enb. reg */ 536#define PKSEL_ADDR 0xfffff443 /* Port K Select Register */ 537 538#define PKDIR BYTE_REF(PKDIR_ADDR) 539#define PKDATA BYTE_REF(PKDATA_ADDR) 540#define PKPUEN BYTE_REF(PKPUEN_ADDR) 541#define PKSEL BYTE_REF(PKSEL_ADDR) 542 543#define PK(x) (1 << (x)) 544 545#define PK_DATAREADY 0x01 /* Use ~DATA_READY as PK[0] */ 546#define PK_PWM2 0x01 /* Use PWM2 as PK[0] */ 547#define PK_R_W 0x02 /* Use R/W as PK[1] */ 548#define PK_LDS 0x04 /* Use /LDS as PK[2] */ 549#define PK_UDS 0x08 /* Use /UDS as PK[3] */ 550#define PK_LD4 0x10 /* Use LD4 as PK[4] */ 551#define PK_LD5 0x20 /* Use LD5 as PK[5] */ 552#define PK_LD6 0x40 /* Use LD6 as PK[6] */ 553#define PK_LD7 0x80 /* Use LD7 as PK[7] */ 554 555#define PJDIR_ADDR 0xfffff438 /* Port J direction reg */ 556#define PJDATA_ADDR 0xfffff439 /* Port J data register */ 557#define PJPUEN_ADDR 0xfffff43A /* Port J Pull-Up enable reg */ 558#define PJSEL_ADDR 0xfffff43B /* Port J Select Register */ 559 560#define PJDIR BYTE_REF(PJDIR_ADDR) 561#define PJDATA BYTE_REF(PJDATA_ADDR) 562#define PJPUEN BYTE_REF(PJPUEN_ADDR) 563#define PJSEL BYTE_REF(PJSEL_ADDR) 564 565#define PJ(x) (1 << (x)) 566 567#define PJ_MOSI 0x01 /* Use MOSI as PJ[0] */ 568#define PJ_MISO 0x02 /* Use MISO as PJ[1] */ 569#define PJ_SPICLK1 0x04 /* Use SPICLK1 as PJ[2] */ 570#define PJ_SS 0x08 /* Use SS as PJ[3] */ 571#define PJ_RXD2 0x10 /* Use RXD2 as PJ[4] */ 572#define PJ_TXD2 0x20 /* Use TXD2 as PJ[5] */ 573#define PJ_RTS2 0x40 /* Use RTS2 as PJ[5] */ 574#define PJ_CTS2 0x80 /* Use CTS2 as PJ[5] */ 575 576/* 577 * Port M 578 */ 579#define PMDIR_ADDR 0xfffff448 /* Port M direction reg */ 580#define PMDATA_ADDR 0xfffff449 /* Port M data register */ 581#define PMPUEN_ADDR 0xfffff44a /* Port M Pull-Up enable reg */ 582#define PMSEL_ADDR 0xfffff44b /* Port M Select Register */ 583 584#define PMDIR BYTE_REF(PMDIR_ADDR) 585#define PMDATA BYTE_REF(PMDATA_ADDR) 586#define PMPUEN BYTE_REF(PMPUEN_ADDR) 587#define PMSEL BYTE_REF(PMSEL_ADDR) 588 589#define PM(x) (1 << (x)) 590 591#define PM_SDCLK 0x01 /* Use SDCLK as PM[0] */ 592#define PM_SDCE 0x02 /* Use SDCE as PM[1] */ 593#define PM_DQMH 0x04 /* Use DQMH as PM[2] */ 594#define PM_DQML 0x08 /* Use DQML as PM[3] */ 595#define PM_SDA10 0x10 /* Use SDA10 as PM[4] */ 596#define PM_DMOE 0x20 /* Use DMOE as PM[5] */ 597 598/********** 599 * 600 * 0xFFFFF5xx -- Pulse-Width Modulator (PWM) 601 * 602 **********/ 603 604/* 605 * PWM Control Register 606 */ 607#define PWMC_ADDR 0xfffff500 608#define PWMC WORD_REF(PWMC_ADDR) 609 610#define PWMC_CLKSEL_MASK 0x0003 /* Clock Selection */ 611#define PWMC_CLKSEL_SHIFT 0 612#define PWMC_REPEAT_MASK 0x000c /* Sample Repeats */ 613#define PWMC_REPEAT_SHIFT 2 614#define PWMC_EN 0x0010 /* Enable PWM */ 615#define PMNC_FIFOAV 0x0020 /* FIFO Available */ 616#define PWMC_IRQEN 0x0040 /* Interrupt Request Enable */ 617#define PWMC_IRQ 0x0080 /* Interrupt Request (FIFO empty) */ 618#define PWMC_PRESCALER_MASK 0x7f00 /* Incoming Clock prescaler */ 619#define PWMC_PRESCALER_SHIFT 8 620#define PWMC_CLKSRC 0x8000 /* Clock Source Select */ 621 622/* '328-compatible definitions */ 623#define PWMC_PWMEN PWMC_EN 624 625/* 626 * PWM Sample Register 627 */ 628#define PWMS_ADDR 0xfffff502 629#define PWMS WORD_REF(PWMS_ADDR) 630 631/* 632 * PWM Period Register 633 */ 634#define PWMP_ADDR 0xfffff504 635#define PWMP BYTE_REF(PWMP_ADDR) 636 637/* 638 * PWM Counter Register 639 */ 640#define PWMCNT_ADDR 0xfffff505 641#define PWMCNT BYTE_REF(PWMCNT_ADDR) 642 643/********** 644 * 645 * 0xFFFFF6xx -- General-Purpose Timer 646 * 647 **********/ 648 649/* 650 * Timer Control register 651 */ 652#define TCTL_ADDR 0xfffff600 653#define TCTL WORD_REF(TCTL_ADDR) 654 655#define TCTL_TEN 0x0001 /* Timer Enable */ 656#define TCTL_CLKSOURCE_MASK 0x000e /* Clock Source: */ 657#define TCTL_CLKSOURCE_STOP 0x0000 /* Stop count (disabled) */ 658#define TCTL_CLKSOURCE_SYSCLK 0x0002 /* SYSCLK to prescaler */ 659#define TCTL_CLKSOURCE_SYSCLK_16 0x0004 /* SYSCLK/16 to prescaler */ 660#define TCTL_CLKSOURCE_TIN 0x0006 /* TIN to prescaler */ 661#define TCTL_CLKSOURCE_32KHZ 0x0008 /* 32kHz clock to prescaler */ 662#define TCTL_IRQEN 0x0010 /* IRQ Enable */ 663#define TCTL_OM 0x0020 /* Output Mode */ 664#define TCTL_CAP_MASK 0x00c0 /* Capture Edge: */ 665#define TCTL_CAP_RE 0x0040 /* Capture on rizing edge */ 666#define TCTL_CAP_FE 0x0080 /* Capture on falling edge */ 667#define TCTL_FRR 0x0010 /* Free-Run Mode */ 668 669/* '328-compatible definitions */ 670#define TCTL1_ADDR TCTL_ADDR 671#define TCTL1 TCTL 672 673/* 674 * Timer Prescaler Register 675 */ 676#define TPRER_ADDR 0xfffff602 677#define TPRER WORD_REF(TPRER_ADDR) 678 679/* '328-compatible definitions */ 680#define TPRER1_ADDR TPRER_ADDR 681#define TPRER1 TPRER 682 683/* 684 * Timer Compare Register 685 */ 686#define TCMP_ADDR 0xfffff604 687#define TCMP WORD_REF(TCMP_ADDR) 688 689/* '328-compatible definitions */ 690#define TCMP1_ADDR TCMP_ADDR 691#define TCMP1 TCMP 692 693/* 694 * Timer Capture register 695 */ 696#define TCR_ADDR 0xfffff606 697#define TCR WORD_REF(TCR_ADDR) 698 699/* '328-compatible definitions */ 700#define TCR1_ADDR TCR_ADDR 701#define TCR1 TCR 702 703/* 704 * Timer Counter Register 705 */ 706#define TCN_ADDR 0xfffff608 707#define TCN WORD_REF(TCN_ADDR) 708 709/* '328-compatible definitions */ 710#define TCN1_ADDR TCN_ADDR 711#define TCN1 TCN 712 713/* 714 * Timer Status Register 715 */ 716#define TSTAT_ADDR 0xfffff60a 717#define TSTAT WORD_REF(TSTAT_ADDR) 718 719#define TSTAT_COMP 0x0001 /* Compare Event occurred */ 720#define TSTAT_CAPT 0x0001 /* Capture Event occurred */ 721 722/* '328-compatible definitions */ 723#define TSTAT1_ADDR TSTAT_ADDR 724#define TSTAT1 TSTAT 725 726/********** 727 * 728 * 0xFFFFF8xx -- Serial Peripheral Interface Master (SPIM) 729 * 730 **********/ 731 732/* 733 * SPIM Data Register 734 */ 735#define SPIMDATA_ADDR 0xfffff800 736#define SPIMDATA WORD_REF(SPIMDATA_ADDR) 737 738/* 739 * SPIM Control/Status Register 740 */ 741#define SPIMCONT_ADDR 0xfffff802 742#define SPIMCONT WORD_REF(SPIMCONT_ADDR) 743 744#define SPIMCONT_BIT_COUNT_MASK 0x000f /* Transfer Length in Bytes */ 745#define SPIMCONT_BIT_COUNT_SHIFT 0 746#define SPIMCONT_POL 0x0010 /* SPMCLK Signel Polarity */ 747#define SPIMCONT_PHA 0x0020 /* Clock/Data phase relationship */ 748#define SPIMCONT_IRQEN 0x0040 /* IRQ Enable */ 749#define SPIMCONT_IRQ 0x0080 /* Interrupt Request */ 750#define SPIMCONT_XCH 0x0100 /* Exchange */ 751#define SPIMCONT_ENABLE 0x0200 /* Enable SPIM */ 752#define SPIMCONT_DATA_RATE_MASK 0xe000 /* SPIM Data Rate */ 753#define SPIMCONT_DATA_RATE_SHIFT 13 754 755/* '328-compatible definitions */ 756#define SPIMCONT_SPIMIRQ SPIMCONT_IRQ 757#define SPIMCONT_SPIMEN SPIMCONT_ENABLE 758 759/********** 760 * 761 * 0xFFFFF9xx -- UART 762 * 763 **********/ 764 765/* 766 * UART Status/Control Register 767 */ 768 769#define USTCNT_ADDR 0xfffff900 770#define USTCNT WORD_REF(USTCNT_ADDR) 771 772#define USTCNT_TXAE 0x0001 /* Transmitter Available Interrupt Enable */ 773#define USTCNT_TXHE 0x0002 /* Transmitter Half Empty Enable */ 774#define USTCNT_TXEE 0x0004 /* Transmitter Empty Interrupt Enable */ 775#define USTCNT_RXRE 0x0008 /* Receiver Ready Interrupt Enable */ 776#define USTCNT_RXHE 0x0010 /* Receiver Half-Full Interrupt Enable */ 777#define USTCNT_RXFE 0x0020 /* Receiver Full Interrupt Enable */ 778#define USTCNT_CTSD 0x0040 /* CTS Delta Interrupt Enable */ 779#define USTCNT_ODEN 0x0080 /* Old Data Interrupt Enable */ 780#define USTCNT_8_7 0x0100 /* Eight or seven-bit transmission */ 781#define USTCNT_STOP 0x0200 /* Stop bit transmission */ 782#define USTCNT_ODD 0x0400 /* Odd Parity */ 783#define USTCNT_PEN 0x0800 /* Parity Enable */ 784#define USTCNT_CLKM 0x1000 /* Clock Mode Select */ 785#define USTCNT_TXEN 0x2000 /* Transmitter Enable */ 786#define USTCNT_RXEN 0x4000 /* Receiver Enable */ 787#define USTCNT_UEN 0x8000 /* UART Enable */ 788 789/* '328-compatible definitions */ 790#define USTCNT_TXAVAILEN USTCNT_TXAE 791#define USTCNT_TXHALFEN USTCNT_TXHE 792#define USTCNT_TXEMPTYEN USTCNT_TXEE 793#define USTCNT_RXREADYEN USTCNT_RXRE 794#define USTCNT_RXHALFEN USTCNT_RXHE 795#define USTCNT_RXFULLEN USTCNT_RXFE 796#define USTCNT_CTSDELTAEN USTCNT_CTSD 797#define USTCNT_ODD_EVEN USTCNT_ODD 798#define USTCNT_PARITYEN USTCNT_PEN 799#define USTCNT_CLKMODE USTCNT_CLKM 800#define USTCNT_UARTEN USTCNT_UEN 801 802/* 803 * UART Baud Control Register 804 */ 805#define UBAUD_ADDR 0xfffff902 806#define UBAUD WORD_REF(UBAUD_ADDR) 807 808#define UBAUD_PRESCALER_MASK 0x003f /* Actual divisor is 65 - PRESCALER */ 809#define UBAUD_PRESCALER_SHIFT 0 810#define UBAUD_DIVIDE_MASK 0x0700 /* Baud Rate freq. divisor */ 811#define UBAUD_DIVIDE_SHIFT 8 812#define UBAUD_BAUD_SRC 0x0800 /* Baud Rate Source */ 813#define UBAUD_UCLKDIR 0x2000 /* UCLK Direction */ 814 815/* 816 * UART Receiver Register 817 */ 818#define URX_ADDR 0xfffff904 819#define URX WORD_REF(URX_ADDR) 820 821#define URX_RXDATA_ADDR 0xfffff905 822#define URX_RXDATA BYTE_REF(URX_RXDATA_ADDR) 823 824#define URX_RXDATA_MASK 0x00ff /* Received data */ 825#define URX_RXDATA_SHIFT 0 826#define URX_PARITY_ERROR 0x0100 /* Parity Error */ 827#define URX_BREAK 0x0200 /* Break Detected */ 828#define URX_FRAME_ERROR 0x0400 /* Framing Error */ 829#define URX_OVRUN 0x0800 /* Serial Overrun */ 830#define URX_OLD_DATA 0x1000 /* Old data in FIFO */ 831#define URX_DATA_READY 0x2000 /* Data Ready (FIFO not empty) */ 832#define URX_FIFO_HALF 0x4000 /* FIFO is Half-Full */ 833#define URX_FIFO_FULL 0x8000 /* FIFO is Full */ 834 835/* 836 * UART Transmitter Register 837 */ 838#define UTX_ADDR 0xfffff906 839#define UTX WORD_REF(UTX_ADDR) 840 841#define UTX_TXDATA_ADDR 0xfffff907 842#define UTX_TXDATA BYTE_REF(UTX_TXDATA_ADDR) 843 844#define UTX_TXDATA_MASK 0x00ff /* Data to be transmitted */ 845#define UTX_TXDATA_SHIFT 0 846#define UTX_CTS_DELTA 0x0100 /* CTS changed */ 847#define UTX_CTS_STAT 0x0200 /* CTS State */ 848#define UTX_BUSY 0x0400 /* FIFO is busy, sending a character */ 849#define UTX_NOCTS 0x0800 /* Ignore CTS */ 850#define UTX_SEND_BREAK 0x1000 /* Send a BREAK */ 851#define UTX_TX_AVAIL 0x2000 /* Transmit FIFO has a slot available */ 852#define UTX_FIFO_HALF 0x4000 /* Transmit FIFO is half empty */ 853#define UTX_FIFO_EMPTY 0x8000 /* Transmit FIFO is empty */ 854 855/* '328-compatible definitions */ 856#define UTX_CTS_STATUS UTX_CTS_STAT 857#define UTX_IGNORE_CTS UTX_NOCTS 858 859/* 860 * UART Miscellaneous Register 861 */ 862#define UMISC_ADDR 0xfffff908 863#define UMISC WORD_REF(UMISC_ADDR) 864 865#define UMISC_TX_POL 0x0004 /* Transmit Polarity */ 866#define UMISC_RX_POL 0x0008 /* Receive Polarity */ 867#define UMISC_IRDA_LOOP 0x0010 /* IrDA Loopback Enable */ 868#define UMISC_IRDA_EN 0x0020 /* Infra-Red Enable */ 869#define UMISC_RTS 0x0040 /* Set RTS status */ 870#define UMISC_RTSCONT 0x0080 /* Choose RTS control */ 871#define UMISC_IR_TEST 0x0400 /* IRDA Test Enable */ 872#define UMISC_BAUD_RESET 0x0800 /* Reset Baud Rate Generation Counters */ 873#define UMISC_LOOP 0x1000 /* Serial Loopback Enable */ 874#define UMISC_FORCE_PERR 0x2000 /* Force Parity Error */ 875#define UMISC_CLKSRC 0x4000 /* Clock Source */ 876#define UMISC_BAUD_TEST 0x8000 /* Enable Baud Test Mode */ 877 878/* 879 * UART Non-integer Prescaler Register 880 */ 881#define NIPR_ADDR 0xfffff90a 882#define NIPR WORD_REF(NIPR_ADDR) 883 884#define NIPR_STEP_VALUE_MASK 0x00ff /* NI prescaler step value */ 885#define NIPR_STEP_VALUE_SHIFT 0 886#define NIPR_SELECT_MASK 0x0700 /* Tap Selection */ 887#define NIPR_SELECT_SHIFT 8 888#define NIPR_PRE_SEL 0x8000 /* Non-integer prescaler select */ 889 890 891/* generalization of uart control registers to support multiple ports: */ 892typedef struct { 893 volatile unsigned short int ustcnt; 894 volatile unsigned short int ubaud; 895 union { 896 volatile unsigned short int w; 897 struct { 898 volatile unsigned char status; 899 volatile unsigned char rxdata; 900 } b; 901 } urx; 902 union { 903 volatile unsigned short int w; 904 struct { 905 volatile unsigned char status; 906 volatile unsigned char txdata; 907 } b; 908 } utx; 909 volatile unsigned short int umisc; 910 volatile unsigned short int nipr; 911 volatile unsigned short int hmark; 912 volatile unsigned short int unused; 913} __packed m68328_uart; 914 915 916 917 918/********** 919 * 920 * 0xFFFFFAxx -- LCD Controller 921 * 922 **********/ 923 924/* 925 * LCD Screen Starting Address Register 926 */ 927#define LSSA_ADDR 0xfffffa00 928#define LSSA LONG_REF(LSSA_ADDR) 929 930#define LSSA_SSA_MASK 0x1ffffffe /* Bits 0 and 29-31 are reserved */ 931 932/* 933 * LCD Virtual Page Width Register 934 */ 935#define LVPW_ADDR 0xfffffa05 936#define LVPW BYTE_REF(LVPW_ADDR) 937 938/* 939 * LCD Screen Width Register (not compatible with '328 !!!) 940 */ 941#define LXMAX_ADDR 0xfffffa08 942#define LXMAX WORD_REF(LXMAX_ADDR) 943 944#define LXMAX_XM_MASK 0x02f0 /* Bits 0-3 and 10-15 are reserved */ 945 946/* 947 * LCD Screen Height Register 948 */ 949#define LYMAX_ADDR 0xfffffa0a 950#define LYMAX WORD_REF(LYMAX_ADDR) 951 952#define LYMAX_YM_MASK 0x01ff /* Bits 9-15 are reserved */ 953 954/* 955 * LCD Cursor X Position Register 956 */ 957#define LCXP_ADDR 0xfffffa18 958#define LCXP WORD_REF(LCXP_ADDR) 959 960#define LCXP_CC_MASK 0xc000 /* Cursor Control */ 961#define LCXP_CC_TRAMSPARENT 0x0000 962#define LCXP_CC_BLACK 0x4000 963#define LCXP_CC_REVERSED 0x8000 964#define LCXP_CC_WHITE 0xc000 965#define LCXP_CXP_MASK 0x02ff /* Cursor X position */ 966 967/* 968 * LCD Cursor Y Position Register 969 */ 970#define LCYP_ADDR 0xfffffa1a 971#define LCYP WORD_REF(LCYP_ADDR) 972 973#define LCYP_CYP_MASK 0x01ff /* Cursor Y Position */ 974 975/* 976 * LCD Cursor Width and Heigth Register 977 */ 978#define LCWCH_ADDR 0xfffffa1c 979#define LCWCH WORD_REF(LCWCH_ADDR) 980 981#define LCWCH_CH_MASK 0x001f /* Cursor Height */ 982#define LCWCH_CH_SHIFT 0 983#define LCWCH_CW_MASK 0x1f00 /* Cursor Width */ 984#define LCWCH_CW_SHIFT 8 985 986/* 987 * LCD Blink Control Register 988 */ 989#define LBLKC_ADDR 0xfffffa1f 990#define LBLKC BYTE_REF(LBLKC_ADDR) 991 992#define LBLKC_BD_MASK 0x7f /* Blink Divisor */ 993#define LBLKC_BD_SHIFT 0 994#define LBLKC_BKEN 0x80 /* Blink Enabled */ 995 996/* 997 * LCD Panel Interface Configuration Register 998 */ 999#define LPICF_ADDR 0xfffffa20 1000#define LPICF BYTE_REF(LPICF_ADDR) 1001 1002#define LPICF_GS_MASK 0x03 /* Gray-Scale Mode */ 1003#define LPICF_GS_BW 0x00 1004#define LPICF_GS_GRAY_4 0x01 1005#define LPICF_GS_GRAY_16 0x02 1006#define LPICF_PBSIZ_MASK 0x0c /* Panel Bus Width */ 1007#define LPICF_PBSIZ_1 0x00 1008#define LPICF_PBSIZ_2 0x04 1009#define LPICF_PBSIZ_4 0x08 1010 1011/* 1012 * LCD Polarity Configuration Register 1013 */ 1014#define LPOLCF_ADDR 0xfffffa21 1015#define LPOLCF BYTE_REF(LPOLCF_ADDR) 1016 1017#define LPOLCF_PIXPOL 0x01 /* Pixel Polarity */ 1018#define LPOLCF_LPPOL 0x02 /* Line Pulse Polarity */ 1019#define LPOLCF_FLMPOL 0x04 /* Frame Marker Polarity */ 1020#define LPOLCF_LCKPOL 0x08 /* LCD Shift Lock Polarity */ 1021 1022/* 1023 * LACD (LCD Alternate Crystal Direction) Rate Control Register 1024 */ 1025#define LACDRC_ADDR 0xfffffa23 1026#define LACDRC BYTE_REF(LACDRC_ADDR) 1027 1028#define LACDRC_ACDSLT 0x80 /* Signal Source Select */ 1029#define LACDRC_ACD_MASK 0x0f /* Alternate Crystal Direction Control */ 1030#define LACDRC_ACD_SHIFT 0 1031 1032/* 1033 * LCD Pixel Clock Divider Register 1034 */ 1035#define LPXCD_ADDR 0xfffffa25 1036#define LPXCD BYTE_REF(LPXCD_ADDR) 1037 1038#define LPXCD_PCD_MASK 0x3f /* Pixel Clock Divider */ 1039#define LPXCD_PCD_SHIFT 0 1040 1041/* 1042 * LCD Clocking Control Register 1043 */ 1044#define LCKCON_ADDR 0xfffffa27 1045#define LCKCON BYTE_REF(LCKCON_ADDR) 1046 1047#define LCKCON_DWS_MASK 0x0f /* Display Wait-State */ 1048#define LCKCON_DWS_SHIFT 0 1049#define LCKCON_DWIDTH 0x40 /* Display Memory Width */ 1050#define LCKCON_LCDON 0x80 /* Enable LCD Controller */ 1051 1052/* '328-compatible definitions */ 1053#define LCKCON_DW_MASK LCKCON_DWS_MASK 1054#define LCKCON_DW_SHIFT LCKCON_DWS_SHIFT 1055 1056/* 1057 * LCD Refresh Rate Adjustment Register 1058 */ 1059#define LRRA_ADDR 0xfffffa29 1060#define LRRA BYTE_REF(LRRA_ADDR) 1061 1062/* 1063 * LCD Panning Offset Register 1064 */ 1065#define LPOSR_ADDR 0xfffffa2d 1066#define LPOSR BYTE_REF(LPOSR_ADDR) 1067 1068#define LPOSR_POS_MASK 0x0f /* Pixel Offset Code */ 1069#define LPOSR_POS_SHIFT 0 1070 1071/* 1072 * LCD Frame Rate Control Modulation Register 1073 */ 1074#define LFRCM_ADDR 0xfffffa31 1075#define LFRCM BYTE_REF(LFRCM_ADDR) 1076 1077#define LFRCM_YMOD_MASK 0x0f /* Vertical Modulation */ 1078#define LFRCM_YMOD_SHIFT 0 1079#define LFRCM_XMOD_MASK 0xf0 /* Horizontal Modulation */ 1080#define LFRCM_XMOD_SHIFT 4 1081 1082/* 1083 * LCD Gray Palette Mapping Register 1084 */ 1085#define LGPMR_ADDR 0xfffffa33 1086#define LGPMR BYTE_REF(LGPMR_ADDR) 1087 1088#define LGPMR_G1_MASK 0x0f 1089#define LGPMR_G1_SHIFT 0 1090#define LGPMR_G2_MASK 0xf0 1091#define LGPMR_G2_SHIFT 4 1092 1093/* 1094 * PWM Contrast Control Register 1095 */ 1096#define PWMR_ADDR 0xfffffa36 1097#define PWMR WORD_REF(PWMR_ADDR) 1098 1099#define PWMR_PW_MASK 0x00ff /* Pulse Width */ 1100#define PWMR_PW_SHIFT 0 1101#define PWMR_CCPEN 0x0100 /* Contrast Control Enable */ 1102#define PWMR_SRC_MASK 0x0600 /* Input Clock Source */ 1103#define PWMR_SRC_LINE 0x0000 /* Line Pulse */ 1104#define PWMR_SRC_PIXEL 0x0200 /* Pixel Clock */ 1105#define PWMR_SRC_LCD 0x4000 /* LCD clock */ 1106 1107/********** 1108 * 1109 * 0xFFFFFBxx -- Real-Time Clock (RTC) 1110 * 1111 **********/ 1112 1113/* 1114 * RTC Hours Minutes and Seconds Register 1115 */ 1116#define RTCTIME_ADDR 0xfffffb00 1117#define RTCTIME LONG_REF(RTCTIME_ADDR) 1118 1119#define RTCTIME_SECONDS_MASK 0x0000003f /* Seconds */ 1120#define RTCTIME_SECONDS_SHIFT 0 1121#define RTCTIME_MINUTES_MASK 0x003f0000 /* Minutes */ 1122#define RTCTIME_MINUTES_SHIFT 16 1123#define RTCTIME_HOURS_MASK 0x1f000000 /* Hours */ 1124#define RTCTIME_HOURS_SHIFT 24 1125 1126/* 1127 * RTC Alarm Register 1128 */ 1129#define RTCALRM_ADDR 0xfffffb04 1130#define RTCALRM LONG_REF(RTCALRM_ADDR) 1131 1132#define RTCALRM_SECONDS_MASK 0x0000003f /* Seconds */ 1133#define RTCALRM_SECONDS_SHIFT 0 1134#define RTCALRM_MINUTES_MASK 0x003f0000 /* Minutes */ 1135#define RTCALRM_MINUTES_SHIFT 16 1136#define RTCALRM_HOURS_MASK 0x1f000000 /* Hours */ 1137#define RTCALRM_HOURS_SHIFT 24 1138 1139/* 1140 * Watchdog Timer Register 1141 */ 1142#define WATCHDOG_ADDR 0xfffffb0a 1143#define WATCHDOG WORD_REF(WATCHDOG_ADDR) 1144 1145#define WATCHDOG_EN 0x0001 /* Watchdog Enabled */ 1146#define WATCHDOG_ISEL 0x0002 /* Select the watchdog interrupt */ 1147#define WATCHDOG_INTF 0x0080 /* Watchdog interrupt occurred */ 1148#define WATCHDOG_CNT_MASK 0x0300 /* Watchdog Counter */ 1149#define WATCHDOG_CNT_SHIFT 8 1150 1151/* 1152 * RTC Control Register 1153 */ 1154#define RTCCTL_ADDR 0xfffffb0c 1155#define RTCCTL WORD_REF(RTCCTL_ADDR) 1156 1157#define RTCCTL_XTL 0x0020 /* Crystal Selection */ 1158#define RTCCTL_EN 0x0080 /* RTC Enable */ 1159 1160/* '328-compatible definitions */ 1161#define RTCCTL_384 RTCCTL_XTL 1162#define RTCCTL_ENABLE RTCCTL_EN 1163 1164/* 1165 * RTC Interrupt Status Register 1166 */ 1167#define RTCISR_ADDR 0xfffffb0e 1168#define RTCISR WORD_REF(RTCISR_ADDR) 1169 1170#define RTCISR_SW 0x0001 /* Stopwatch timed out */ 1171#define RTCISR_MIN 0x0002 /* 1-minute interrupt has occurred */ 1172#define RTCISR_ALM 0x0004 /* Alarm interrupt has occurred */ 1173#define RTCISR_DAY 0x0008 /* 24-hour rollover interrupt has occurred */ 1174#define RTCISR_1HZ 0x0010 /* 1Hz interrupt has occurred */ 1175#define RTCISR_HR 0x0020 /* 1-hour interrupt has occurred */ 1176#define RTCISR_SAM0 0x0100 /* 4Hz / 4.6875Hz interrupt has occurred */ 1177#define RTCISR_SAM1 0x0200 /* 8Hz / 9.3750Hz interrupt has occurred */ 1178#define RTCISR_SAM2 0x0400 /* 16Hz / 18.7500Hz interrupt has occurred */ 1179#define RTCISR_SAM3 0x0800 /* 32Hz / 37.5000Hz interrupt has occurred */ 1180#define RTCISR_SAM4 0x1000 /* 64Hz / 75.0000Hz interrupt has occurred */ 1181#define RTCISR_SAM5 0x2000 /* 128Hz / 150.0000Hz interrupt has occurred */ 1182#define RTCISR_SAM6 0x4000 /* 256Hz / 300.0000Hz interrupt has occurred */ 1183#define RTCISR_SAM7 0x8000 /* 512Hz / 600.0000Hz interrupt has occurred */ 1184 1185/* 1186 * RTC Interrupt Enable Register 1187 */ 1188#define RTCIENR_ADDR 0xfffffb10 1189#define RTCIENR WORD_REF(RTCIENR_ADDR) 1190 1191#define RTCIENR_SW 0x0001 /* Stopwatch interrupt enable */ 1192#define RTCIENR_MIN 0x0002 /* 1-minute interrupt enable */ 1193#define RTCIENR_ALM 0x0004 /* Alarm interrupt enable */ 1194#define RTCIENR_DAY 0x0008 /* 24-hour rollover interrupt enable */ 1195#define RTCIENR_1HZ 0x0010 /* 1Hz interrupt enable */ 1196#define RTCIENR_HR 0x0020 /* 1-hour interrupt enable */ 1197#define RTCIENR_SAM0 0x0100 /* 4Hz / 4.6875Hz interrupt enable */ 1198#define RTCIENR_SAM1 0x0200 /* 8Hz / 9.3750Hz interrupt enable */ 1199#define RTCIENR_SAM2 0x0400 /* 16Hz / 18.7500Hz interrupt enable */ 1200#define RTCIENR_SAM3 0x0800 /* 32Hz / 37.5000Hz interrupt enable */ 1201#define RTCIENR_SAM4 0x1000 /* 64Hz / 75.0000Hz interrupt enable */ 1202#define RTCIENR_SAM5 0x2000 /* 128Hz / 150.0000Hz interrupt enable */ 1203#define RTCIENR_SAM6 0x4000 /* 256Hz / 300.0000Hz interrupt enable */ 1204#define RTCIENR_SAM7 0x8000 /* 512Hz / 600.0000Hz interrupt enable */ 1205 1206/* 1207 * Stopwatch Minutes Register 1208 */ 1209#define STPWCH_ADDR 0xfffffb12 1210#define STPWCH WORD_REF(STPWCH_ADDR) 1211 1212#define STPWCH_CNT_MASK 0x003f /* Stopwatch countdown value */ 1213#define SPTWCH_CNT_SHIFT 0 1214 1215/* 1216 * RTC Day Count Register 1217 */ 1218#define DAYR_ADDR 0xfffffb1a 1219#define DAYR WORD_REF(DAYR_ADDR) 1220 1221#define DAYR_DAYS_MASK 0x1ff /* Day Setting */ 1222#define DAYR_DAYS_SHIFT 0 1223 1224/* 1225 * RTC Day Alarm Register 1226 */ 1227#define DAYALARM_ADDR 0xfffffb1c 1228#define DAYALARM WORD_REF(DAYALARM_ADDR) 1229 1230#define DAYALARM_DAYSAL_MASK 0x01ff /* Day Setting of the Alarm */ 1231#define DAYALARM_DAYSAL_SHIFT 0 1232 1233/********** 1234 * 1235 * 0xFFFFFCxx -- DRAM Controller 1236 * 1237 **********/ 1238 1239/* 1240 * DRAM Memory Configuration Register 1241 */ 1242#define DRAMMC_ADDR 0xfffffc00 1243#define DRAMMC WORD_REF(DRAMMC_ADDR) 1244 1245#define DRAMMC_ROW12_MASK 0xc000 /* Row address bit for MD12 */ 1246#define DRAMMC_ROW12_PA10 0x0000 1247#define DRAMMC_ROW12_PA21 0x4000 1248#define DRAMMC_ROW12_PA23 0x8000 1249#define DRAMMC_ROW0_MASK 0x3000 /* Row address bit for MD0 */ 1250#define DRAMMC_ROW0_PA11 0x0000 1251#define DRAMMC_ROW0_PA22 0x1000 1252#define DRAMMC_ROW0_PA23 0x2000 1253#define DRAMMC_ROW11 0x0800 /* Row address bit for MD11 PA20/PA22 */ 1254#define DRAMMC_ROW10 0x0400 /* Row address bit for MD10 PA19/PA21 */ 1255#define DRAMMC_ROW9 0x0200 /* Row address bit for MD9 PA9/PA19 */ 1256#define DRAMMC_ROW8 0x0100 /* Row address bit for MD8 PA10/PA20 */ 1257#define DRAMMC_COL10 0x0080 /* Col address bit for MD10 PA11/PA0 */ 1258#define DRAMMC_COL9 0x0040 /* Col address bit for MD9 PA10/PA0 */ 1259#define DRAMMC_COL8 0x0020 /* Col address bit for MD8 PA9/PA0 */ 1260#define DRAMMC_REF_MASK 0x001f /* Refresh Cycle */ 1261#define DRAMMC_REF_SHIFT 0 1262 1263/* 1264 * DRAM Control Register 1265 */ 1266#define DRAMC_ADDR 0xfffffc02 1267#define DRAMC WORD_REF(DRAMC_ADDR) 1268 1269#define DRAMC_DWE 0x0001 /* DRAM Write Enable */ 1270#define DRAMC_RST 0x0002 /* Reset Burst Refresh Enable */ 1271#define DRAMC_LPR 0x0004 /* Low-Power Refresh Enable */ 1272#define DRAMC_SLW 0x0008 /* Slow RAM */ 1273#define DRAMC_LSP 0x0010 /* Light Sleep */ 1274#define DRAMC_MSW 0x0020 /* Slow Multiplexing */ 1275#define DRAMC_WS_MASK 0x00c0 /* Wait-states */ 1276#define DRAMC_WS_SHIFT 6 1277#define DRAMC_PGSZ_MASK 0x0300 /* Page Size for fast page mode */ 1278#define DRAMC_PGSZ_SHIFT 8 1279#define DRAMC_PGSZ_256K 0x0000 1280#define DRAMC_PGSZ_512K 0x0100 1281#define DRAMC_PGSZ_1024K 0x0200 1282#define DRAMC_PGSZ_2048K 0x0300 1283#define DRAMC_EDO 0x0400 /* EDO DRAM */ 1284#define DRAMC_CLK 0x0800 /* Refresh Timer Clock source select */ 1285#define DRAMC_BC_MASK 0x3000 /* Page Access Clock Cycle (FP mode) */ 1286#define DRAMC_BC_SHIFT 12 1287#define DRAMC_RM 0x4000 /* Refresh Mode */ 1288#define DRAMC_EN 0x8000 /* DRAM Controller enable */ 1289 1290 1291/********** 1292 * 1293 * 0xFFFFFDxx -- In-Circuit Emulation (ICE) 1294 * 1295 **********/ 1296 1297/* 1298 * ICE Module Address Compare Register 1299 */ 1300#define ICEMACR_ADDR 0xfffffd00 1301#define ICEMACR LONG_REF(ICEMACR_ADDR) 1302 1303/* 1304 * ICE Module Address Mask Register 1305 */ 1306#define ICEMAMR_ADDR 0xfffffd04 1307#define ICEMAMR LONG_REF(ICEMAMR_ADDR) 1308 1309/* 1310 * ICE Module Control Compare Register 1311 */ 1312#define ICEMCCR_ADDR 0xfffffd08 1313#define ICEMCCR WORD_REF(ICEMCCR_ADDR) 1314 1315#define ICEMCCR_PD 0x0001 /* Program/Data Cycle Selection */ 1316#define ICEMCCR_RW 0x0002 /* Read/Write Cycle Selection */ 1317 1318/* 1319 * ICE Module Control Mask Register 1320 */ 1321#define ICEMCMR_ADDR 0xfffffd0a 1322#define ICEMCMR WORD_REF(ICEMCMR_ADDR) 1323 1324#define ICEMCMR_PDM 0x0001 /* Program/Data Cycle Mask */ 1325#define ICEMCMR_RWM 0x0002 /* Read/Write Cycle Mask */ 1326 1327/* 1328 * ICE Module Control Register 1329 */ 1330#define ICEMCR_ADDR 0xfffffd0c 1331#define ICEMCR WORD_REF(ICEMCR_ADDR) 1332 1333#define ICEMCR_CEN 0x0001 /* Compare Enable */ 1334#define ICEMCR_PBEN 0x0002 /* Program Break Enable */ 1335#define ICEMCR_SB 0x0004 /* Single Breakpoint */ 1336#define ICEMCR_HMDIS 0x0008 /* HardMap disable */ 1337#define ICEMCR_BBIEN 0x0010 /* Bus Break Interrupt Enable */ 1338 1339/* 1340 * ICE Module Status Register 1341 */ 1342#define ICEMSR_ADDR 0xfffffd0e 1343#define ICEMSR WORD_REF(ICEMSR_ADDR) 1344 1345#define ICEMSR_EMUEN 0x0001 /* Emulation Enable */ 1346#define ICEMSR_BRKIRQ 0x0002 /* A-Line Vector Fetch Detected */ 1347#define ICEMSR_BBIRQ 0x0004 /* Bus Break Interrupt Detected */ 1348#define ICEMSR_EMIRQ 0x0008 /* EMUIRQ Falling Edge Detected */ 1349 1350#endif /* _MC68VZ328_H_ */ 1351