1// SPDX-License-Identifier: GPL-2.0
2/*
3 * Device Tree file for ITian Square One SQ201 NAS
4 */
5
6/dts-v1/;
7
8#include "gemini.dtsi"
9#include <dt-bindings/input/input.h>
10
11/ {
12	model = "ITian Square One SQ201";
13	compatible = "itian,sq201", "cortina,gemini";
14	#address-cells = <1>;
15	#size-cells = <1>;
16
17	memory@0 { /* 128 MB */
18		device_type = "memory";
19		reg = <0x00000000 0x8000000>;
20	};
21
22	chosen {
23		bootargs = "console=ttyS0,115200n8 root=/dev/mtdblock2 rw rootfstype=squashfs,jffs2 rootwait";
24		stdout-path = &uart0;
25	};
26
27	gpio_keys {
28		compatible = "gpio-keys";
29
30		button-setup {
31			debounce-interval = <100>;
32			wakeup-source;
33			linux,code = <KEY_RESTART>;
34			label = "factory reset";
35			/* Conflict with NAND flash */
36			gpios = <&gpio0 18 GPIO_ACTIVE_LOW>;
37		};
38	};
39
40	leds {
41		compatible = "gpio-leds";
42		led-green-info {
43			label = "sq201:green:info";
44			gpios = <&gpio0 20 GPIO_ACTIVE_HIGH>;
45			default-state = "on";
46			linux,default-trigger = "heartbeat";
47		};
48		led-green-usb {
49			label = "sq201:green:usb";
50			gpios = <&gpio0 31 GPIO_ACTIVE_HIGH>;
51			default-state = "off";
52			linux,default-trigger = "usb-host";
53		};
54	};
55
56	mdio0: mdio {
57		compatible = "virtual,mdio-gpio";
58		/* Uses MDC and MDIO */
59		gpios = <&gpio0 22 GPIO_ACTIVE_HIGH>, /* MDC */
60			<&gpio0 21 GPIO_ACTIVE_HIGH>; /* MDIO */
61		#address-cells = <1>;
62		#size-cells = <0>;
63
64		/* This is a Marvell 88E1111 ethernet transciever */
65		phy0: ethernet-phy@1 {
66			reg = <1>;
67		};
68	};
69
70	spi {
71		compatible = "spi-gpio";
72		#address-cells = <1>;
73		#size-cells = <0>;
74		/* Check pin collisions */
75		sck-gpios = <&gpio1 28 GPIO_ACTIVE_HIGH>;
76		miso-gpios = <&gpio1 30 GPIO_ACTIVE_HIGH>;
77		mosi-gpios = <&gpio1 29 GPIO_ACTIVE_HIGH>;
78		cs-gpios = <&gpio1 31 GPIO_ACTIVE_HIGH>;
79		num-chipselects = <1>;
80
81		ethernet-switch@0 {
82			compatible = "vitesse,vsc7395";
83			reg = <0>;
84			/* Specified for 2.5 MHz or below */
85			spi-max-frequency = <2500000>;
86			gpio-controller;
87			#gpio-cells = <2>;
88
89			ethernet-ports {
90				#address-cells = <1>;
91				#size-cells = <0>;
92
93				ethernet-port@0 {
94					reg = <0>;
95					label = "lan1";
96				};
97				ethernet-port@1 {
98					reg = <1>;
99					label = "lan2";
100				};
101				ethernet-port@2 {
102					reg = <2>;
103					label = "lan3";
104				};
105				ethernet-port@3 {
106					reg = <3>;
107					label = "lan4";
108				};
109				vsc: ethernet-port@6 {
110					reg = <6>;
111					label = "cpu";
112					ethernet = <&gmac1>;
113					phy-mode = "rgmii";
114					fixed-link {
115						speed = <1000>;
116						full-duplex;
117						pause;
118					};
119				};
120			};
121		};
122	};
123
124
125	soc {
126		flash@30000000 {
127			status = "okay";
128			pinctrl-names = "enabled", "disabled";
129			pinctrl-0 = <&pflash_default_pins>;
130			pinctrl-1 = <&pflash_disabled_pins>;
131			/* 16MB of flash */
132			reg = <0x30000000 0x01000000>;
133
134			partitions {
135				compatible = "redboot-fis";
136				/* Eraseblock at 0xfe0000 */
137				fis-index-block = <0x1fc>;
138			};
139		};
140
141		syscon: syscon@40000000 {
142			pinctrl {
143				/*
144				 * gpio0fgrp cover line 18 used by reset button
145				 * gpio0ggrp cover line 20 used by info LED
146				 * gpio0hgrp cover line 21, 22 used by MDIO for Marvell PHY
147				 * gpio0kgrp cover line 31 used by USB LED
148				 */
149				gpio0_default_pins: pinctrl-gpio0 {
150					mux {
151						function = "gpio0";
152						groups = "gpio0fgrp",
153						"gpio0hgrp";
154					};
155				};
156				/*
157				 * gpio0dgrp cover lines used by the SPI
158				 * to the Vitesse G5x chip.
159				 */
160				gpio1_default_pins: pinctrl-gpio1 {
161					mux {
162						function = "gpio1";
163						groups = "gpio1dgrp";
164					};
165				};
166				/*
167				 * These GPIO groups will be mapped in over some
168				 * of the flash pins when the flash is not in
169				 * active use.
170				 */
171				pflash_disabled_pins: pinctrl-pflash-disabled {
172					mux {
173						function = "gpio0";
174						groups = "gpio0ggrp", "gpio0igrp", "gpio0jgrp",
175							 "gpio0kgrp";
176					};
177				};
178				pinctrl-gmii {
179					mux {
180						function = "gmii";
181						groups = "gmii_gmac0_grp", "gmii_gmac1_grp";
182					};
183					/* Settings come from memory dump in PLATO */
184					conf0 {
185						pins = "V8 GMAC0 RXDV";
186						skew-delay = <0>;
187					};
188					conf1 {
189						pins = "Y7 GMAC0 RXC";
190						skew-delay = <15>;
191					};
192					conf2 {
193						pins = "T8 GMAC0 TXEN";
194						skew-delay = <7>;
195					};
196					conf3 {
197						pins = "U8 GMAC0 TXC";
198						skew-delay = <10>;
199					};
200					conf4 {
201						pins = "T10 GMAC1 RXDV";
202						skew-delay = <7>;
203					};
204					conf5 {
205						pins = "Y11 GMAC1 RXC";
206						skew-delay = <8>;
207					};
208					conf6 {
209						pins = "W11 GMAC1 TXEN";
210						skew-delay = <7>;
211					};
212					conf7 {
213						pins = "V11 GMAC1 TXC";
214						skew-delay = <5>;
215					};
216					conf8 {
217						/* The data lines all have default skew */
218						pins = "W8 GMAC0 RXD0", "V9 GMAC0 RXD1",
219						       "Y8 GMAC0 RXD2", "U9 GMAC0 RXD3",
220						       "T7 GMAC0 TXD0", "U6 GMAC0 TXD1",
221						       "V7 GMAC0 TXD2", "U7 GMAC0 TXD3",
222						       "Y12 GMAC1 RXD0", "V12 GMAC1 RXD1",
223						       "T11 GMAC1 RXD2", "W12 GMAC1 RXD3",
224						       "U10 GMAC1 TXD0", "Y10 GMAC1 TXD1",
225						       "W10 GMAC1 TXD2", "T9 GMAC1 TXD3";
226						skew-delay = <7>;
227					};
228					/* Set up drive strength on GMAC0 and GMAC1 to 16 mA */
229					conf9 {
230						groups = "gmii_gmac0_grp", "gmii_gmac1_grp";
231						drive-strength = <16>;
232					};
233				};
234			};
235		};
236
237		sata: sata@46000000 {
238			cortina,gemini-ata-muxmode = <0>;
239			cortina,gemini-enable-sata-bridge;
240			status = "okay";
241		};
242
243		gpio0: gpio@4d000000 {
244			pinctrl-names = "default";
245			pinctrl-0 = <&gpio0_default_pins>;
246		};
247
248		gpio1: gpio@4e000000 {
249			pinctrl-names = "default";
250			pinctrl-0 = <&gpio1_default_pins>;
251		};
252
253		pci@50000000 {
254			status = "okay";
255		};
256
257		ethernet@60000000 {
258			status = "okay";
259
260			ethernet-port@0 {
261				phy-mode = "rgmii";
262				phy-handle = <&phy0>;
263			};
264			ethernet-port@1 {
265				phy-mode = "rgmii";
266				fixed-link {
267					speed = <1000>;
268					full-duplex;
269					pause;
270				};
271			};
272		};
273
274		ide@63000000 {
275			status = "okay";
276		};
277
278		usb@68000000 {
279			status = "okay";
280		};
281
282		usb@69000000 {
283			status = "okay";
284		};
285	};
286};
287