1/* 2 * Copyright (c) 2002-2008 Sam Leffler, Errno Consulting 3 * Copyright (c) 2002-2008 Atheros Communications, Inc. 4 * 5 * Permission to use, copy, modify, and/or distribute this software for any 6 * purpose with or without fee is hereby granted, provided that the above 7 * copyright notice and this permission notice appear in all copies. 8 * 9 * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES 10 * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF 11 * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR 12 * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES 13 * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN 14 * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF 15 * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE. 16 * 17 * $FreeBSD$ 18 */ 19 20#ifndef _DEV_ATH_DESC_H 21#define _DEV_ATH_DESC_H 22 23#include "opt_ah.h" /* NB: required for AH_SUPPORT_AR5416 */ 24 25/* 26 * Transmit descriptor status. This structure is filled 27 * in only after the tx descriptor process method finds a 28 * ``done'' descriptor; at which point it returns something 29 * other than HAL_EINPROGRESS. 30 * 31 * Note that ts_antenna may not be valid for all h/w. It 32 * should be used only if non-zero. 33 */ 34struct ath_tx_status { 35 uint16_t ts_seqnum; /* h/w assigned sequence number */ 36 uint16_t ts_tstamp; /* h/w assigned timestamp */ 37 uint8_t ts_status; /* frame status, 0 => xmit ok */ 38 uint8_t ts_rate; /* h/w transmit rate index */ 39 int8_t ts_rssi; /* tx ack RSSI */ 40 uint8_t ts_shortretry; /* # short retries */ 41 uint8_t ts_longretry; /* # long retries */ 42 uint8_t ts_virtcol; /* virtual collision count */ 43 uint8_t ts_antenna; /* antenna information */ 44 uint8_t ts_finaltsi; /* final transmit series index */ 45#ifdef AH_SUPPORT_AR5416 46 /* 802.11n status */ 47 uint8_t ts_flags; /* misc flags */ 48 int8_t ts_rssi_ctl[3]; /* tx ack RSSI [ctl, chain 0-2] */ 49 int8_t ts_rssi_ext[3]; /* tx ack RSSI [ext, chain 0-2] */ 50/* #define ts_rssi ts_rssi_combined */ 51 uint32_t ts_ba_low; /* blockack bitmap low */ 52 uint32_t ts_ba_high; /* blockack bitmap high */ 53 uint32_t ts_evm0; /* evm bytes */ 54 uint32_t ts_evm1; 55 uint32_t ts_evm2; 56#endif /* AH_SUPPORT_AR5416 */ 57}; 58 59/* bits found in ts_status */ 60#define HAL_TXERR_XRETRY 0x01 /* excessive retries */ 61#define HAL_TXERR_FILT 0x02 /* blocked by tx filtering */ 62#define HAL_TXERR_FIFO 0x04 /* fifo underrun */ 63#define HAL_TXERR_XTXOP 0x08 /* txop exceeded */ 64#define HAL_TXERR_TIMER_EXPIRED 0x10 /* Tx timer expired */ 65 66/* bits found in ts_flags */ 67#define HAL_TX_BA 0x01 /* Block Ack seen */ 68#define HAL_TX_AGGR 0x02 /* Aggregate */ 69#define HAL_TX_DESC_CFG_ERR 0x10 /* Error in 20/40 desc config */ 70#define HAL_TX_DATA_UNDERRUN 0x20 /* Tx buffer underrun */ 71#define HAL_TX_DELIM_UNDERRUN 0x40 /* Tx delimiter underrun */ 72 73/* 74 * Receive descriptor status. This structure is filled 75 * in only after the rx descriptor process method finds a 76 * ``done'' descriptor; at which point it returns something 77 * other than HAL_EINPROGRESS. 78 * 79 * If rx_status is zero, then the frame was received ok; 80 * otherwise the error information is indicated and rs_phyerr 81 * contains a phy error code if HAL_RXERR_PHY is set. In general 82 * the frame contents is undefined when an error occurred thought 83 * for some errors (e.g. a decryption error), it may be meaningful. 84 * 85 * Note that the receive timestamp is expanded using the TSF to 86 * at least 15 bits (regardless of what the h/w provides directly). 87 * Newer hardware supports a full 32-bits; use HAL_CAP_32TSTAMP to 88 * find out if the hardware is capable. 89 * 90 * rx_rssi is in units of dbm above the noise floor. This value 91 * is measured during the preamble and PLCP; i.e. with the initial 92 * 4us of detection. The noise floor is typically a consistent 93 * -96dBm absolute power in a 20MHz channel. 94 */ 95struct ath_rx_status { 96 uint16_t rs_datalen; /* rx frame length */ 97 uint8_t rs_status; /* rx status, 0 => recv ok */ 98 uint8_t rs_phyerr; /* phy error code */ 99 int8_t rs_rssi; /* rx frame RSSI (combined for 11n) */ 100 uint8_t rs_keyix; /* key cache index */ 101 uint8_t rs_rate; /* h/w receive rate index */ 102 uint8_t rs_more; /* more descriptors follow */ 103 uint32_t rs_tstamp; /* h/w assigned timestamp */ 104 uint32_t rs_antenna; /* antenna information */ 105#ifdef AH_SUPPORT_AR5416 106 /* 802.11n status */ 107 int8_t rs_rssi_ctl[3]; /* rx frame RSSI [ctl, chain 0-2] */ 108 int8_t rs_rssi_ext[3]; /* rx frame RSSI [ext, chain 0-2] */ 109 uint8_t rs_isaggr; /* is part of the aggregate */ 110 uint8_t rs_moreaggr; /* more frames in aggr to follow */ 111 uint8_t rs_num_delims; /* number of delims in aggr */ 112 uint8_t rs_flags; /* misc flags */ 113 uint32_t rs_evm0; /* evm bytes */ 114 uint32_t rs_evm1; 115 uint32_t rs_evm2; 116 uint32_t rs_evm3; /* needed for ar9300 and later */ 117 uint32_t rs_evm4; /* needed for ar9300 and later */ 118#endif /* AH_SUPPORT_AR5416 */ 119}; 120 121/* bits found in rs_status */ 122#define HAL_RXERR_CRC 0x01 /* CRC error on frame */ 123#define HAL_RXERR_PHY 0x02 /* PHY error, rs_phyerr is valid */ 124#define HAL_RXERR_FIFO 0x04 /* fifo overrun */ 125#define HAL_RXERR_DECRYPT 0x08 /* non-Michael decrypt error */ 126#define HAL_RXERR_MIC 0x10 /* Michael MIC decrypt error */ 127 128/* bits found in rs_flags */ 129#define HAL_RX_MORE 0x01 /* more descriptors follow */ 130#define HAL_RX_MORE_AGGR 0x02 /* more frames in aggr */ 131#define HAL_RX_GI 0x04 /* full gi */ 132#define HAL_RX_2040 0x08 /* 40 Mhz */ 133#define HAL_RX_DELIM_CRC_PRE 0x10 /* crc error in delimiter pre */ 134#define HAL_RX_DELIM_CRC_POST 0x20 /* crc error in delim after */ 135#define HAL_RX_DECRYPT_BUSY 0x40 /* decrypt was too slow */ 136#define HAL_RX_HI_RX_CHAIN 0x80 /* SM power save: hi Rx chain control */ 137 138enum { 139 HAL_PHYERR_UNDERRUN = 0, /* Transmit underrun */ 140 HAL_PHYERR_TIMING = 1, /* Timing error */ 141 HAL_PHYERR_PARITY = 2, /* Illegal parity */ 142 HAL_PHYERR_RATE = 3, /* Illegal rate */ 143 HAL_PHYERR_LENGTH = 4, /* Illegal length */ 144 HAL_PHYERR_RADAR = 5, /* Radar detect */ 145 HAL_PHYERR_SERVICE = 6, /* Illegal service */ 146 HAL_PHYERR_TOR = 7, /* Transmit override receive */ 147 /* NB: these are specific to the 5212 and later */ 148 HAL_PHYERR_OFDM_TIMING = 17, /* */ 149 HAL_PHYERR_OFDM_SIGNAL_PARITY = 18, /* */ 150 HAL_PHYERR_OFDM_RATE_ILLEGAL = 19, /* */ 151 HAL_PHYERR_OFDM_LENGTH_ILLEGAL = 20, /* */ 152 HAL_PHYERR_OFDM_POWER_DROP = 21, /* */ 153 HAL_PHYERR_OFDM_SERVICE = 22, /* */ 154 HAL_PHYERR_OFDM_RESTART = 23, /* */ 155 HAL_PHYERR_FALSE_RADAR_EXT = 24, /* */ 156 HAL_PHYERR_CCK_TIMING = 25, /* */ 157 HAL_PHYERR_CCK_HEADER_CRC = 26, /* */ 158 HAL_PHYERR_CCK_RATE_ILLEGAL = 27, /* */ 159 HAL_PHYERR_CCK_SERVICE = 30, /* */ 160 HAL_PHYERR_CCK_RESTART = 31, /* */ 161 HAL_PHYERR_CCK_LENGTH_ILLEGAL = 32, /* */ 162 HAL_PHYERR_CCK_POWER_DROP = 33, /* */ 163 /* AR5416 and later */ 164 HAL_PHYERR_HT_CRC_ERROR = 34, /* */ 165 HAL_PHYERR_HT_LENGTH_ILLEGAL = 35, /* */ 166 HAL_PHYERR_HT_RATE_ILLEGAL = 36, /* */ 167}; 168 169/* value found in rs_keyix to mark invalid entries */ 170#define HAL_RXKEYIX_INVALID ((uint8_t) -1) 171/* value used to specify no encryption key for xmit */ 172#define HAL_TXKEYIX_INVALID ((u_int) -1) 173 174/* XXX rs_antenna definitions */ 175 176/* 177 * Definitions for the software frame/packet descriptors used by 178 * the Atheros HAL. This definition obscures hardware-specific 179 * details from the driver. Drivers are expected to fillin the 180 * portions of a descriptor that are not opaque then use HAL calls 181 * to complete the work. Status for completed frames is returned 182 * in a device-independent format. 183 */ 184#ifdef AH_SUPPORT_AR5416 185#define HAL_DESC_HW_SIZE 20 186#else 187#define HAL_DESC_HW_SIZE 4 188#endif /* AH_SUPPORT_AR5416 */ 189 190struct ath_desc { 191 /* 192 * The following definitions are passed directly 193 * the hardware and managed by the HAL. Drivers 194 * should not touch those elements marked opaque. 195 */ 196 uint32_t ds_link; /* phys address of next descriptor */ 197 uint32_t ds_data; /* phys address of data buffer */ 198 uint32_t ds_ctl0; /* opaque DMA control 0 */ 199 uint32_t ds_ctl1; /* opaque DMA control 1 */ 200 uint32_t ds_hw[HAL_DESC_HW_SIZE]; /* opaque h/w region */ 201}; 202 203struct ath_desc_status { 204 union { 205 struct ath_tx_status tx;/* xmit status */ 206 struct ath_rx_status rx;/* recv status */ 207 } ds_us; 208}; 209 210#define ds_txstat ds_us.tx 211#define ds_rxstat ds_us.rx 212 213/* flags passed to tx descriptor setup methods */ 214#define HAL_TXDESC_CLRDMASK 0x0001 /* clear destination filter mask */ 215#define HAL_TXDESC_NOACK 0x0002 /* don't wait for ACK */ 216#define HAL_TXDESC_RTSENA 0x0004 /* enable RTS */ 217#define HAL_TXDESC_CTSENA 0x0008 /* enable CTS */ 218#define HAL_TXDESC_INTREQ 0x0010 /* enable per-descriptor interrupt */ 219#define HAL_TXDESC_VEOL 0x0020 /* mark virtual EOL */ 220/* NB: this only affects frame, not any RTS/CTS */ 221#define HAL_TXDESC_DURENA 0x0040 /* enable h/w write of duration field */ 222#define HAL_TXDESC_EXT_ONLY 0x0080 /* send on ext channel only (11n) */ 223#define HAL_TXDESC_EXT_AND_CTL 0x0100 /* send on ext + ctl channels (11n) */ 224#define HAL_TXDESC_VMF 0x0200 /* virtual more frag */ 225 226/* flags passed to rx descriptor setup methods */ 227#define HAL_RXDESC_INTREQ 0x0020 /* enable per-descriptor interrupt */ 228#endif /* _DEV_ATH_DESC_H */ 229