1/* 2 * Copyright (c) 1996, Sujal M. Patel 3 * All rights reserved. 4 * 5 * Redistribution and use in source and binary forms, with or without 6 * modification, are permitted provided that the following conditions 7 * are met: 8 * 1. Redistributions of source code must retain the above copyright 9 * notice, this list of conditions and the following disclaimer. 10 * 2. Redistributions in binary form must reproduce the above copyright 11 * notice, this list of conditions and the following disclaimer in the 12 * documentation and/or other materials provided with the distribution. 13 * 3. All advertising materials mentioning features or use of this software 14 * must display the following acknowledgement: 15 * This product includes software developed by Sujal M. Patel 16 * 4. Neither the name of the author nor the names of any co-contributors 17 * may be used to endorse or promote products derived from this software 18 * without specific prior written permission. 19 * 20 * THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND 21 * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE 22 * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE 23 * ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE 24 * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL 25 * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS 26 * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) 27 * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT 28 * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY 29 * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF 30 * SUCH DAMAGE. 31 */ 32 33#ifndef _I386_ISA_PNP_H_ 34#define _I386_ISA_PNP_H_ 35 36/* Maximum Number of PnP Devices. 8 should be plenty */ 37#define MAX_PNP_CARDS 8 38/* 39 * the following is the maximum number of PnP Logical devices that 40 * userconfig can handle. 41 */ 42#define MAX_PNP_LDN 20 43 44/* Static ports to access PnP state machine */ 45#ifndef _KERNEL 46#define _PNP_ADDRESS 0x279 47#define _PNP_WRITE_DATA 0xa79 48#endif 49 50/* PnP Registers. Write to ADDRESS and then use WRITE/READ_DATA */ 51#define SET_RD_DATA 0x00 52 /*** 53 Writing to this location modifies the address of the port used for 54 reading from the Plug and Play ISA cards. Bits[7:0] become I/O 55 read port address bits[9:2]. Reads from this register are ignored. 56 ***/ 57 58#define SERIAL_ISOLATION 0x01 59 /*** 60 A read to this register causes a Plug and Play cards in the Isolation 61 state to compare one bit of the boards ID. 62 This register is read only. 63 ***/ 64 65#define CONFIG_CONTROL 0x02 66 /*** 67 Bit[2] Reset CSN to 0 68 Bit[1] Return to the Wait for Key state 69 Bit[0] Reset all logical devices and restore configuration 70 registers to their power-up values. 71 72 A write to bit[0] of this register performs a reset function on 73 all logical devices. This resets the contents of configuration 74 registers to their default state. All card's logical devices 75 enter their default state and the CSN is preserved. 76 77 A write to bit[1] of this register causes all cards to enter the 78 Wait for Key state but all CSNs are preserved and logical devices 79 are not affected. 80 81 A write to bit[2] of this register causes all cards to reset their 82 CSN to zero . 83 84 This register is write-only. The values are not sticky, that is, 85 hardware will automatically clear them and there is no need for 86 software to clear the bits. 87 ***/ 88 89#define WAKE 0x03 90 /*** 91 A write to this port will cause all cards that have a CSN that 92 matches the write data[7:0] to go from the Sleep state to the either 93 the Isolation state if the write data for this command is zero or 94 the Config state if the write data is not zero. Additionally, the 95 pointer to the byte-serial device is reset. This register is 96 writeonly. 97 ***/ 98 99#define RESOURCE_DATA 0x04 100 /*** 101 A read from this address reads the next byte of resource information. 102 The Status register must be polled until bit[0] is set before this 103 register may be read. This register is read only. 104 ***/ 105 106#define STATUS 0x05 107 /*** 108 Bit[0] when set indicates it is okay to read the next data byte 109 from the Resource Data register. This register is readonly. 110 ***/ 111 112#define SET_CSN 0x06 113 /*** 114 A write to this port sets a card's CSN. The CSN is a value uniquely 115 assigned to each ISA card after the serial identification process 116 so that each card may be individually selected during a Wake[CSN] 117 command. This register is read/write. 118 ***/ 119 120#define SET_LDN 0x07 121 /*** 122 Selects the current logical device. All reads and writes of memory, 123 I/O, interrupt and DMA configuration information access the registers 124 of the logical device written here. In addition, the I/O Range 125 Check and Activate commands operate only on the selected logical 126 device. This register is read/write. If a card has only 1 logical 127 device, this location should be a read-only value of 0x00. 128 ***/ 129 130/*** addresses 0x08 - 0x1F Card Level Reserved for future use ***/ 131/*** addresses 0x20 - 0x2F Card Level, Vendor Defined ***/ 132 133#define ACTIVATE 0x30 134 /*** 135 For each logical device there is one activate register that controls 136 whether or not the logical device is active on the ISA bus. Bit[0], 137 if set, activates the logical device. Bits[7:1] are reserved and 138 must return 0 on reads. This is a read/write register. Before a 139 logical device is activated, I/O range check must be disabled. 140 ***/ 141 142#define IO_RANGE_CHECK 0x31 143 /*** 144 This register is used to perform a conflict check on the I/O port 145 range programmed for use by a logical device. 146 147 Bit[7:2] Reserved and must return 0 on reads 148 Bit[1] Enable I/O Range check, if set then I/O Range Check 149 is enabled. I/O range check is only valid when the logical 150 device is inactive. 151 152 Bit[0], if set, forces the logical device to respond to I/O reads 153 of the logical device's assigned I/O range with a 0x55 when I/O 154 range check is in operation. If clear, the logical device drives 155 0xAA. This register is read/write. 156 ***/ 157 158/*** addr 0x32 - 0x37 Logical Device Control Reserved for future use ***/ 159/*** addr 0x38 - 0x3F Logical Device Control Vendor Define ***/ 160 161#define MEM_CONFIG 0x40 162 /*** 163 Four memory resource registers per range, four ranges. 164 Fill with 0 if no ranges are enabled. 165 166 Offset 0: RW Memory base address bits[23:16] 167 Offset 1: RW Memory base address bits[15:8] 168 Offset 2: Memory control 169 Bit[1] specifies 8/16-bit control. This bit is set to indicate 170 16-bit memory, and cleared to indicate 8-bit memory. 171 Bit[0], if cleared, indicates the next field can be used as a range 172 length for decode (implies range length and base alignment of memory 173 descriptor are equal). 174 Bit[0], if set, indicates the next field is the upper limit for 175 the address. - - Bit[0] is read-only. 176 Offset 3: RW upper limit or range len, bits[23:16] 177 Offset 4: RW upper limit or range len, bits[15:8] 178 Offset 5-Offset 7: filler, unused. 179 ***/ 180 181#define IO_CONFIG_BASE 0x60 182 /*** 183 Eight ranges, two bytes per range. 184 Offset 0: I/O port base address bits[15:8] 185 Offset 1: I/O port base address bits[7:0] 186 ***/ 187 188#define IRQ_CONFIG 0x70 189 /*** 190 Two entries, two bytes per entry. 191 Offset 0: RW interrupt level (1..15, 0=unused). 192 Offset 1: Bit[1]: level(1:hi, 0:low), 193 Bit[0]: type (1:level, 0:edge) 194 byte 1 can be readonly if 1 type of int is used. 195 ***/ 196 197#define DRQ_CONFIG 0x74 198 /*** 199 Two entries, one byte per entry. Bits[2:0] select 200 which DMA channel is in use for DMA 0. Zero selects DMA channel 201 0, seven selects DMA channel 7. DMA channel 4, the cascade channel 202 is used to indicate no DMA channel is active. 203 ***/ 204 205/*** 32-bit memory accesses are at 0x76 ***/ 206 207/* Macros to parse Resource IDs */ 208#define PNP_RES_TYPE(a) (a >> 7) 209#define PNP_SRES_NUM(a) (a >> 3) 210#define PNP_SRES_LEN(a) (a & 0x07) 211#define PNP_LRES_NUM(a) (a & 0x7f) 212 213/* Small Resource Item names */ 214#define PNP_VERSION 0x1 215#define LOG_DEVICE_ID 0x2 216#define COMP_DEVICE_ID 0x3 217#define IRQ_FORMAT 0x4 218#define DMA_FORMAT 0x5 219#define START_DEPEND_FUNC 0x6 220#define END_DEPEND_FUNC 0x7 221#define IO_PORT_DESC 0x8 222#define FIXED_IO_PORT_DESC 0x9 223#define SM_RES_RESERVED 0xa-0xd 224#define SM_VENDOR_DEFINED 0xe 225#define END_TAG 0xf 226 227/* Large Resource Item names */ 228#define MEMORY_RANGE_DESC 0x1 229#define ID_STRING_ANSI 0x2 230#define ID_STRING_UNICODE 0x3 231#define LG_VENDOR_DEFINED 0x4 232#define _32BIT_MEM_RANGE_DESC 0x5 233#define _32BIT_FIXED_LOC_DESC 0x6 234#define LG_RES_RESERVED 0x7-0x7f 235 236/* 237 * pnp_cinfo contains Configuration Information. They are used 238 * to communicate to the device driver the actual configuration 239 * of the device, and also by the userconfig menu to let the 240 * operating system override any configuration set by the bios. 241 * 242 */ 243struct pnp_cinfo { 244 u_int vendor_id; /* board id */ 245 u_int serial; /* Board's Serial Number */ 246 u_long flags; /* OS-reserved flags */ 247 u_char csn; /* assigned Card Select Number */ 248 u_char ldn; /* Logical Device Number */ 249 u_char enable; /* pnp enable */ 250 u_char override; /* override bios parms (in userconfig) */ 251 u_char irq[2]; /* IRQ Number */ 252 u_char irq_type[2]; /* IRQ Type */ 253 u_char drq[2]; 254 u_short port[8]; /* The Base Address of the Port */ 255 struct { 256 u_long base; /* Memory Base Address */ 257 int control; /* Memory Control Register */ 258 u_long range; /* Memory Range *OR* Upper Limit */ 259 } mem[4]; 260}; 261 262#ifdef _KERNEL 263 264struct pnp_device { 265 char *pd_name; 266 char * (*pd_probe ) (u_long csn, u_long vendor_id); 267 void (*pd_attach ) (u_long csn, u_long vend_id, char * name, 268 struct isa_device *dev); 269 u_long *pd_count; 270 u_int *imask ; 271}; 272 273struct _pnp_id { 274 u_long vendor_id; 275 u_long serial; 276 u_char checksum; 277} ; 278 279struct pnp_dlist_node { 280 struct pnp_device *pnp; 281 struct isa_device dev; 282 struct pnp_dlist_node *next; 283}; 284 285typedef struct _pnp_id pnp_id; 286extern struct pnp_dlist_node *pnp_device_list; 287extern pnp_id pnp_devices[MAX_PNP_CARDS]; 288extern struct pnp_cinfo pnp_ldn_overrides[MAX_PNP_LDN]; 289extern int pnp_overrides_valid; 290 291/* 292 * these two functions are for use in drivers 293 */ 294int read_pnp_parms(struct pnp_cinfo *d, int ldn); 295int write_pnp_parms(struct pnp_cinfo *d, int ldn); 296int enable_pnp_card(void); 297 298/* 299 * used by autoconfigure to actually probe and attach drivers 300 */ 301void pnp_configure(void); 302 303#endif /* _KERNEL */ 304 305#endif /* !_I386_ISA_PNP_H_ */ 306