1/*- 2 * SPDX-License-Identifier: BSD-2-Clause-FreeBSD 3 * 4 * Copyright (c) 2012, 2013 The FreeBSD Foundation 5 * All rights reserved. 6 * 7 * This software was developed by Oleksandr Rybalko under sponsorship 8 * from the FreeBSD Foundation. 9 * 10 * Redistribution and use in source and binary forms, with or without 11 * modification, are permitted provided that the following conditions 12 * are met: 13 * 1. Redistributions of source code must retain the above copyright 14 * notice, this list of conditions and the following disclaimer. 15 * 2. Redistributions in binary form must reproduce the above copyright 16 * notice, this list of conditions and the following disclaimer in the 17 * documentation and/or other materials provided with the distribution. 18 * 19 * THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND 20 * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE 21 * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE 22 * ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE 23 * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL 24 * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS 25 * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) 26 * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT 27 * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY 28 * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF 29 * SUCH DAMAGE. 30 */ 31 32#include <sys/cdefs.h> 33__FBSDID("$FreeBSD$"); 34 35#include <sys/param.h> 36#include <sys/systm.h> 37#include <sys/bus.h> 38#include <sys/kernel.h> 39#include <sys/module.h> 40#include <sys/rman.h> 41#include <sys/timeet.h> 42#include <sys/timetc.h> 43#include <machine/bus.h> 44#include <machine/intr.h> 45#include <machine/machdep.h> /* For arm_set_delay */ 46 47#include <dev/ofw/openfirm.h> 48#include <dev/ofw/ofw_bus.h> 49#include <dev/ofw/ofw_bus_subr.h> 50 51#include <arm/freescale/imx/imx_ccmvar.h> 52#include <arm/freescale/imx/imx_gptreg.h> 53 54#define WRITE4(_sc, _r, _v) \ 55 bus_space_write_4((_sc)->sc_iot, (_sc)->sc_ioh, (_r), (_v)) 56#define READ4(_sc, _r) \ 57 bus_space_read_4((_sc)->sc_iot, (_sc)->sc_ioh, (_r)) 58#define SET4(_sc, _r, _m) \ 59 WRITE4((_sc), (_r), READ4((_sc), (_r)) | (_m)) 60#define CLEAR4(_sc, _r, _m) \ 61 WRITE4((_sc), (_r), READ4((_sc), (_r)) & ~(_m)) 62 63static u_int imx_gpt_get_timecount(struct timecounter *); 64static int imx_gpt_timer_start(struct eventtimer *, sbintime_t, 65 sbintime_t); 66static int imx_gpt_timer_stop(struct eventtimer *); 67 68static void imx_gpt_do_delay(int, void *); 69 70static int imx_gpt_intr(void *); 71static int imx_gpt_probe(device_t); 72static int imx_gpt_attach(device_t); 73 74static struct timecounter imx_gpt_timecounter = { 75 .tc_name = "iMXGPT", 76 .tc_get_timecount = imx_gpt_get_timecount, 77 .tc_counter_mask = ~0u, 78 .tc_frequency = 0, 79 .tc_quality = 1000, 80}; 81 82struct imx_gpt_softc { 83 device_t sc_dev; 84 struct resource * res[2]; 85 bus_space_tag_t sc_iot; 86 bus_space_handle_t sc_ioh; 87 void * sc_ih; /* interrupt handler */ 88 uint32_t sc_period; 89 uint32_t sc_clksrc; 90 uint32_t clkfreq; 91 uint32_t ir_reg; 92 struct eventtimer et; 93}; 94 95/* Try to divide down an available fast clock to this frequency. */ 96#define TARGET_FREQUENCY 1000000000 97 98static struct resource_spec imx_gpt_spec[] = { 99 { SYS_RES_MEMORY, 0, RF_ACTIVE }, 100 { SYS_RES_IRQ, 0, RF_ACTIVE }, 101 { -1, 0 } 102}; 103 104static struct ofw_compat_data compat_data[] = { 105 {"fsl,imx6dl-gpt", 1}, 106 {"fsl,imx6q-gpt", 1}, 107 {"fsl,imx6ul-gpt", 1}, 108 {"fsl,imx53-gpt", 1}, 109 {"fsl,imx51-gpt", 1}, 110 {"fsl,imx31-gpt", 1}, 111 {"fsl,imx27-gpt", 1}, 112 {"fsl,imx25-gpt", 1}, 113 {NULL, 0} 114}; 115 116static int 117imx_gpt_probe(device_t dev) 118{ 119 120 if (!ofw_bus_status_okay(dev)) 121 return (ENXIO); 122 123 /* 124 * We only support a single unit, because the only thing this driver 125 * does with the complex timer hardware is supply the system 126 * timecounter and eventtimer. There is nothing useful we can do with 127 * the additional device instances that exist in some chips. 128 */ 129 if (device_get_unit(dev) > 0) 130 return (ENXIO); 131 132 if (ofw_bus_search_compatible(dev, compat_data)->ocd_data != 0) { 133 device_set_desc(dev, "Freescale i.MX GPT timer"); 134 return (BUS_PROBE_DEFAULT); 135 } 136 137 return (ENXIO); 138} 139 140static int 141imx_gpt_attach(device_t dev) 142{ 143 struct imx_gpt_softc *sc; 144 int ctlreg, err; 145 uint32_t basefreq, prescale, setup_ticks, t1, t2; 146 147 sc = device_get_softc(dev); 148 149 if (bus_alloc_resources(dev, imx_gpt_spec, sc->res)) { 150 device_printf(dev, "could not allocate resources\n"); 151 return (ENXIO); 152 } 153 154 sc->sc_dev = dev; 155 sc->sc_iot = rman_get_bustag(sc->res[0]); 156 sc->sc_ioh = rman_get_bushandle(sc->res[0]); 157 158 /* 159 * For now, just automatically choose a good clock for the hardware 160 * we're running on. Eventually we could allow selection from the fdt; 161 * the code in this driver will cope with any clock frequency. 162 */ 163 sc->sc_clksrc = GPT_CR_CLKSRC_IPG; 164 165 ctlreg = 0; 166 167 switch (sc->sc_clksrc) { 168 case GPT_CR_CLKSRC_32K: 169 basefreq = 32768; 170 break; 171 case GPT_CR_CLKSRC_IPG: 172 basefreq = imx_ccm_ipg_hz(); 173 break; 174 case GPT_CR_CLKSRC_IPG_HIGH: 175 basefreq = imx_ccm_ipg_hz() * 2; 176 break; 177 case GPT_CR_CLKSRC_24M: 178 ctlreg |= GPT_CR_24MEN; 179 basefreq = 24000000; 180 break; 181 case GPT_CR_CLKSRC_NONE:/* Can't run without a clock. */ 182 case GPT_CR_CLKSRC_EXT: /* No way to get the freq of an ext clock. */ 183 default: 184 device_printf(dev, "Unsupported clock source '%d'\n", 185 sc->sc_clksrc); 186 return (EINVAL); 187 } 188 189 /* 190 * The following setup sequence is from the I.MX6 reference manual, 191 * "Selecting the clock source". First, disable the clock and 192 * interrupts. This also clears input and output mode bits and in 193 * general completes several of the early steps in the procedure. 194 */ 195 WRITE4(sc, IMX_GPT_CR, 0); 196 WRITE4(sc, IMX_GPT_IR, 0); 197 198 /* Choose the clock and the power-saving behaviors. */ 199 ctlreg |= 200 sc->sc_clksrc | /* Use selected clock */ 201 GPT_CR_FRR | /* Just count (FreeRunner mode) */ 202 GPT_CR_STOPEN | /* Run in STOP mode */ 203 GPT_CR_DOZEEN | /* Run in DOZE mode */ 204 GPT_CR_WAITEN | /* Run in WAIT mode */ 205 GPT_CR_DBGEN; /* Run in DEBUG mode */ 206 WRITE4(sc, IMX_GPT_CR, ctlreg); 207 208 /* 209 * The datasheet says to do the software reset after choosing the clock 210 * source. It says nothing about needing to wait for the reset to 211 * complete, but the register description does document the fact that 212 * the reset isn't complete until the SWR bit reads 0, so let's be safe. 213 * The reset also clears all registers except for a few of the bits in 214 * CR, but we'll rewrite all the CR bits when we start the counter. 215 */ 216 WRITE4(sc, IMX_GPT_CR, ctlreg | GPT_CR_SWR); 217 while (READ4(sc, IMX_GPT_CR) & GPT_CR_SWR) 218 continue; 219 220 /* Set a prescaler value that gets us near the target frequency. */ 221 if (basefreq < TARGET_FREQUENCY) { 222 prescale = 0; 223 sc->clkfreq = basefreq; 224 } else { 225 prescale = basefreq / TARGET_FREQUENCY; 226 sc->clkfreq = basefreq / prescale; 227 prescale -= 1; /* 1..n range is 0..n-1 in hardware. */ 228 } 229 WRITE4(sc, IMX_GPT_PR, prescale); 230 231 /* Clear the status register. */ 232 WRITE4(sc, IMX_GPT_SR, GPT_IR_ALL); 233 234 /* Start the counter. */ 235 WRITE4(sc, IMX_GPT_CR, ctlreg | GPT_CR_EN); 236 237 if (bootverbose) 238 device_printf(dev, "Running on %dKHz clock, base freq %uHz CR=0x%08x, PR=0x%08x\n", 239 sc->clkfreq / 1000, basefreq, READ4(sc, IMX_GPT_CR), READ4(sc, IMX_GPT_PR)); 240 241 /* Setup the timer interrupt. */ 242 err = bus_setup_intr(dev, sc->res[1], INTR_TYPE_CLK, imx_gpt_intr, 243 NULL, sc, &sc->sc_ih); 244 if (err != 0) { 245 bus_release_resources(dev, imx_gpt_spec, sc->res); 246 device_printf(dev, "Unable to setup the clock irq handler, " 247 "err = %d\n", err); 248 return (ENXIO); 249 } 250 251 /* 252 * Measure how many clock ticks it takes to setup a one-shot event (it's 253 * longer than you might think, due to wait states in accessing gpt 254 * registers). Scale up the result by a factor of 1.5 to be safe, 255 * and use that to set the minimum eventtimer period we can schedule. In 256 * the real world, the value works out to about 750ns on imx5 hardware. 257 */ 258 t1 = READ4(sc, IMX_GPT_CNT); 259 WRITE4(sc, IMX_GPT_OCR3, 0); 260 t2 = READ4(sc, IMX_GPT_CNT); 261 setup_ticks = ((t2 - t1 + 1) * 3) / 2; 262 263 /* Register as an eventtimer. */ 264 sc->et.et_name = "iMXGPT"; 265 sc->et.et_flags = ET_FLAGS_ONESHOT | ET_FLAGS_PERIODIC; 266 sc->et.et_quality = 800; 267 sc->et.et_frequency = sc->clkfreq; 268 sc->et.et_min_period = ((uint64_t)setup_ticks << 32) / sc->clkfreq; 269 sc->et.et_max_period = ((uint64_t)0xfffffffe << 32) / sc->clkfreq; 270 sc->et.et_start = imx_gpt_timer_start; 271 sc->et.et_stop = imx_gpt_timer_stop; 272 sc->et.et_priv = sc; 273 et_register(&sc->et); 274 275 /* Register as a timecounter. */ 276 imx_gpt_timecounter.tc_frequency = sc->clkfreq; 277 imx_gpt_timecounter.tc_priv = sc; 278 tc_init(&imx_gpt_timecounter); 279 280 /* If this is the first unit, store the softc for use in DELAY. */ 281 if (device_get_unit(dev) == 0) { 282 arm_set_delay(imx_gpt_do_delay, sc); 283 } 284 285 return (0); 286} 287 288static int 289imx_gpt_timer_start(struct eventtimer *et, sbintime_t first, sbintime_t period) 290{ 291 struct imx_gpt_softc *sc; 292 uint32_t ticks; 293 294 sc = (struct imx_gpt_softc *)et->et_priv; 295 296 if (period != 0) { 297 sc->sc_period = ((uint32_t)et->et_frequency * period) >> 32; 298 /* Set expected value */ 299 WRITE4(sc, IMX_GPT_OCR2, READ4(sc, IMX_GPT_CNT) + sc->sc_period); 300 /* Enable compare register 2 Interrupt */ 301 sc->ir_reg |= GPT_IR_OF2; 302 WRITE4(sc, IMX_GPT_IR, sc->ir_reg); 303 return (0); 304 } else if (first != 0) { 305 /* Enable compare register 3 interrupt if not already on. */ 306 if ((sc->ir_reg & GPT_IR_OF3) == 0) { 307 sc->ir_reg |= GPT_IR_OF3; 308 WRITE4(sc, IMX_GPT_IR, sc->ir_reg); 309 } 310 ticks = ((uint32_t)et->et_frequency * first) >> 32; 311 /* Do not disturb, otherwise event will be lost */ 312 spinlock_enter(); 313 /* Set expected value */ 314 WRITE4(sc, IMX_GPT_OCR3, READ4(sc, IMX_GPT_CNT) + ticks); 315 /* Now everybody can relax */ 316 spinlock_exit(); 317 return (0); 318 } 319 320 return (EINVAL); 321} 322 323static int 324imx_gpt_timer_stop(struct eventtimer *et) 325{ 326 struct imx_gpt_softc *sc; 327 328 sc = (struct imx_gpt_softc *)et->et_priv; 329 330 /* Disable interrupts and clear any pending status. */ 331 sc->ir_reg &= ~(GPT_IR_OF2 | GPT_IR_OF3); 332 WRITE4(sc, IMX_GPT_IR, sc->ir_reg); 333 WRITE4(sc, IMX_GPT_SR, GPT_IR_OF2 | GPT_IR_OF3); 334 sc->sc_period = 0; 335 336 return (0); 337} 338 339static int 340imx_gpt_intr(void *arg) 341{ 342 struct imx_gpt_softc *sc; 343 uint32_t status; 344 345 sc = (struct imx_gpt_softc *)arg; 346 347 status = READ4(sc, IMX_GPT_SR); 348 349 /* 350 * Clear interrupt status before invoking event callbacks. The callback 351 * often sets up a new one-shot timer event and if the interval is short 352 * enough it can fire before we get out of this function. If we cleared 353 * at the bottom we'd miss the interrupt and hang until the clock wraps. 354 */ 355 WRITE4(sc, IMX_GPT_SR, status); 356 357 /* Handle one-shot timer events. */ 358 if (status & GPT_IR_OF3) { 359 if (sc->et.et_active) { 360 sc->et.et_event_cb(&sc->et, sc->et.et_arg); 361 } 362 } 363 364 /* Handle periodic timer events. */ 365 if (status & GPT_IR_OF2) { 366 if (sc->et.et_active) 367 sc->et.et_event_cb(&sc->et, sc->et.et_arg); 368 if (sc->sc_period != 0) 369 WRITE4(sc, IMX_GPT_OCR2, READ4(sc, IMX_GPT_CNT) + 370 sc->sc_period); 371 } 372 373 return (FILTER_HANDLED); 374} 375 376static u_int 377imx_gpt_get_timecount(struct timecounter *tc) 378{ 379 struct imx_gpt_softc *sc; 380 381 sc = tc->tc_priv; 382 return (READ4(sc, IMX_GPT_CNT)); 383} 384 385static device_method_t imx_gpt_methods[] = { 386 DEVMETHOD(device_probe, imx_gpt_probe), 387 DEVMETHOD(device_attach, imx_gpt_attach), 388 389 DEVMETHOD_END 390}; 391 392static driver_t imx_gpt_driver = { 393 "imx_gpt", 394 imx_gpt_methods, 395 sizeof(struct imx_gpt_softc), 396}; 397 398static devclass_t imx_gpt_devclass; 399 400EARLY_DRIVER_MODULE(imx_gpt, simplebus, imx_gpt_driver, imx_gpt_devclass, 0, 401 0, BUS_PASS_TIMER); 402 403static void 404imx_gpt_do_delay(int usec, void *arg) 405{ 406 struct imx_gpt_softc *sc = arg; 407 uint64_t curcnt, endcnt, startcnt, ticks; 408 409 /* 410 * Calculate the tick count with 64-bit values so that it works for any 411 * clock frequency. Loop until the hardware count reaches start+ticks. 412 * If the 32-bit hardware count rolls over while we're looping, just 413 * manually do a carry into the high bits after each read; don't worry 414 * that doing this on each loop iteration is inefficient -- we're trying 415 * to waste time here. 416 */ 417 ticks = 1 + ((uint64_t)usec * sc->clkfreq) / 1000000; 418 curcnt = startcnt = READ4(sc, IMX_GPT_CNT); 419 endcnt = startcnt + ticks; 420 while (curcnt < endcnt) { 421 curcnt = READ4(sc, IMX_GPT_CNT); 422 if (curcnt < startcnt) 423 curcnt += 1ULL << 32; 424 } 425} 426