xref: /freebsd-11.0-release/sys/pc98/conf/NOTES

#
# NOTES -- Lines that can be cut/pasted into kernel and hints configs.
#
# This file contains machine dependent kernel configuration notes.  For
# machine independent notes, look in /sys/conf/NOTES.
#
# $FreeBSD: head/sys/pc98/conf/NOTES 126708 2004-03-07 04:09:18Z nyan $
#

#
# This directive is mandatory; it defines the architecture to be
# configured for; in this case, the 386 family based PC-98 and
# compatibles.
#
machine		pc98
options 	PC98

#
# We want LINT to cover profiling as well
profile         2


#####################################################################
# SMP OPTIONS:
#
# The apic device enables the use of the I/O APIC for interrupt delivery.
# The apic device can be used in both UP and SMP kernels, but is required
# for SMP kernels.  Thus, the apic device is not strictly an SMP option,
# but it is a prerequisite for SMP.
#
# Notes:
#
# Be sure to disable 'cpu I386_CPU' for SMP kernels.
#
# By default, mixed mode is used to route IRQ0 from the AT timer via
# the 8259A master PIC through the ExtINT pin on the first I/O APIC.
# This can be disabled via the NO_MIXED_MODE option.  In that case,
# IRQ0 will be routed via an intpin on the first I/O APIC.  Not all
# motherboards hook IRQ0 up to the first I/O APIC even though their
# MP table or MADT may claim to do so.  That is why mixed mode is
# enabled by default.
#

# Mandatory:
device		apic			# I/O apic

# Optional:
options 	NO_MIXED_MODE		# Disable use of mixed mode


#####################################################################
# CPU OPTIONS

#
# You must specify at least one CPU (the one you intend to run on);
# deleting the specification for CPUs you don't need to use may make
# parts of the system run faster.
# I386_CPU is mutually exclusive with the other CPU types.
#
#cpu		I386_CPU
cpu		I486_CPU
cpu		I586_CPU		# aka Pentium(tm)
cpu		I686_CPU		# aka Pentium Pro(tm)

#
# Options for CPU features.
#
# CPU_BLUELIGHTNING_3X enables triple-clock mode on IBM Blue Lightning
# CPU if CPU supports it.  The default is double-clock mode on
# BlueLightning CPU box.
#
# CPU_BLUELIGHTNING_FPU_OP_CACHE enables FPU operand cache on IBM
# BlueLightning CPU.  It works only with Cyrix FPU, and this option
# should not be used with Intel FPU.
#
# CPU_BTB_EN enables branch target buffer on Cyrix 5x86 (NOTE 1).
#
# CPU_CYRIX_NO_LOCK enables weak locking for the entire address space
# of Cyrix 6x86 and 6x86MX CPUs by setting the NO_LOCK bit of CCR1.
# Otherwise, the NO_LOCK bit of CCR1 is cleared.  (NOTE 3)
#
# CPU_DIRECT_MAPPED_CACHE sets L1 cache of Cyrix 486DLC CPU in direct
# mapped mode.  Default is 2-way set associative mode.
#
# CPU_DISABLE_5X86_LSSER disables load store serialize (i.e. enables
# reorder).  This option should not be used if you use memory mapped
# I/O device(s).
#
# CPU_DISABLE_CMPXCHG disables the CMPXCHG instruction on > i386 IA32
# machines.  VmWare seems to emulate this instruction poorly, causing
# the guest OS to run very slowly.  Enabling this with a SMP kernel
# will cause the kernel to be unusable.
#
# CPU_DISABLE_SSE explicitly prevent I686_CPU from turning on SSE.
#
# CPU_ENABLE_SSE enables SSE/MMX2 instructions support.  This is default
# on I686_CPU and above.
#
# CPU_FASTER_5X86_FPU enables faster FPU exception handler.
#
# CPU_I486_ON_386 enables CPU cache on i486 based CPU upgrade products
# for i386 machines.
#
# CPU_IORT defines I/O clock delay time (NOTE 1).  Default values of
# I/O clock delay time on Cyrix 5x86 and 6x86 are 0 and 7,respectively
# (no clock delay).
#
# CPU_L2_LATENCY specifies the L2 cache latency value.  This option is used
# only when CPU_PPRO2CELERON is defined and Mendocino Celeron is detected.
# The default value is 5.
#
# CPU_LOOP_EN prevents flushing the prefetch buffer if the destination
# of a jump is already present in the prefetch buffer on Cyrix 5x86(NOTE
# 1).
#
# CPU_PPRO2CELERON enables L2 cache of Mendocino Celeron CPUs.  This option
# is useful when you use Socket 8 to Socket 370 converter, because most Pentium
# Pro BIOSs do not enable L2 cache of Mendocino Celeron CPUs.
#
# CPU_RSTK_EN enables return stack on Cyrix 5x86 (NOTE 1).
#
# CPU_SUSP_HLT enables suspend on HALT.  If this option is set, CPU
# enters suspend mode following execution of HALT instruction.
#
# CPU_UPGRADE_HW_CACHE eliminates unneeded cache flush instruction(s).
#
# CPU_WT_ALLOC enables write allocation on Cyrix 6x86/6x86MX and AMD
# K5/K6/K6-2 CPUs.
#
# CYRIX_CACHE_WORKS enables CPU cache on Cyrix 486 CPUs with cache
# flush at hold state.
#
# CYRIX_CACHE_REALLY_WORKS enables (1) CPU cache on Cyrix 486 CPUs
# without cache flush at hold state, and (2) write-back CPU cache on
# Cyrix 6x86 whose revision < 2.7 (NOTE 2).
#
# NO_F00F_HACK disables the hack that prevents Pentiums (and ONLY
# Pentiums) from locking up when a LOCK CMPXCHG8B instruction is
# executed.  This option is only needed if I586_CPU is also defined,
# and should be included for any non-Pentium CPU that defines it.
#
# NO_MEMORY_HOLE is an optimisation for systems with AMD K6 processors
# which indicates that the 15-16MB range is *definitely* not being
# occupied by an ISA memory hole.
#
# NOTE 1: The options, CPU_BTB_EN, CPU_LOOP_EN, CPU_IORT,
# CPU_LOOP_EN and CPU_RSTK_EN should not be used because of CPU bugs.
# These options may crash your system.
#
# NOTE 2: If CYRIX_CACHE_REALLY_WORKS is not set, CPU cache is enabled
# in write-through mode when revision < 2.7.  If revision of Cyrix
# 6x86 >= 2.7, CPU cache is always enabled in write-back mode.
#
# NOTE 3: This option may cause failures for software that requires
# locked cycles in order to operate correctly.
#
options 	CPU_BLUELIGHTNING_3X
options 	CPU_BLUELIGHTNING_FPU_OP_CACHE
options 	CPU_BTB_EN
options 	CPU_DIRECT_MAPPED_CACHE
options 	CPU_DISABLE_5X86_LSSER
options 	CPU_DISABLE_CMPXCHG
#options 	CPU_DISABLE_SSE
options 	CPU_ENABLE_SSE
options 	CPU_FASTER_5X86_FPU
options 	CPU_I486_ON_386
options 	CPU_IORT
options 	CPU_L2_LATENCY=5
options 	CPU_LOOP_EN
options 	CPU_PPRO2CELERON
options 	CPU_RSTK_EN
options 	CPU_SUSP_HLT
options 	CPU_UPGRADE_HW_CACHE
options 	CPU_WT_ALLOC
options 	CYRIX_CACHE_WORKS
options 	CYRIX_CACHE_REALLY_WORKS
#options 	NO_F00F_HACK

# Debug options
options 	NPX_DEBUG	# enable npx debugging

#
# PERFMON causes the driver for Pentium/Pentium Pro performance counters
# to be compiled.  See perfmon(4) for more information.
#
options 	PERFMON


#####################################################################
# NETWORKING OPTIONS

#
# DEVICE_POLLING adds support for mixed interrupt-polling handling
# of network device drivers, which has significant benefits in terms
# of robustness to overloads and responsivity, as well as permitting
# accurate scheduling of the CPU time between kernel network processing
# and other activities.  The drawback is a moderate (up to 1/HZ seconds)
# potential increase in response times.
# It is strongly recommended to use HZ=1000 or 2000 with DEVICE_POLLING
# to achieve smoother behaviour.
# Additionally, you can enable/disable polling at runtime with the
# sysctl variable kern.polling.enable (defaults off), and select
# the CPU fraction reserved to userland with the sysctl variable
# kern.polling.user_frac (default 50, range 0..100).
#
# Not all device drivers support this mode of operation at the time of
# this writing.  See polling(4) for more details.

options 	DEVICE_POLLING


#####################################################################
# CLOCK OPTIONS

# The following options are used for debugging clock behavior only, and
# should not be used for production systems.

# CLK_CALIBRATION_LOOP causes clock calibration to be run in a loop at
# startup until the user presses a key.  (The i8254 clock is always
# calibrated relative to the RTC (mc146818a) and this option causes the
# calibration to be repeated.)
options 	CLK_CALIBRATION_LOOP

# CLK_USE_I8254_CALIBRATION causes the calibrated frequency of the i8254
# clock to actually be used.
options 	CLK_USE_I8254_CALIBRATION


#####################################################################
# MISCELLANEOUS DEVICES AND OPTIONS

device		speaker		#Play IBM BASIC-style noises out your speaker
hint.speaker.0.at="isa"
hint.speaker.0.port="0x35"
device		gzip		#Exec gzipped a.out's.  REQUIRES COMPAT_AOUT!
device		apm_saver	# Requires APM


#####################################################################
# HARDWARE BUS CONFIGURATION

#
# ISA bus
#
device		isa

#
# Options for `isa':
#
# AUTO_EOI_1 enables the `automatic EOI' feature for the master 8259A
# interrupt controller.  This saves about 0.7-1.25 usec for each interrupt.
# This option breaks suspend/resume on some portables.
#
# MAXMEM specifies the amount of RAM on the machine; if this is not
# specified, FreeBSD will first read the amount of memory from the CMOS
# RAM, so the amount of memory will initially be limited to 64MB or 16MB
# depending on the BIOS.  If the BIOS reports 64MB, a memory probe will
# then attempt to detect the installed amount of RAM.  If this probe
# fails to detect >64MB RAM you will have to use the MAXMEM option.
# The amount is in kilobytes, so for a machine with 128MB of RAM, it would
# be 131072 (128 * 1024).
#
# BROKEN_KEYBOARD_RESET disables the use of the keyboard controller to
# reset the CPU for reboot.  This is needed on some systems with broken
# keyboard controllers.

options 	COMPAT_OLDISA	#Use ISA shims and glue for old drivers
options 	AUTO_EOI_1

options 	MAXMEM=(128*1024)
#options 	BROKEN_KEYBOARD_RESET
options 	EPSON_BOUNCEDMA
options 	EPSON_MEMWIN

#
# PCI bus & PCI options:
#
device		pci

#
# AGP GART support
device		agp


#####################################################################
# HARDWARE DEVICE CONFIGURATION

# PC98 keyboard
device		pckbd
hint.pckbd.0.at="isa"
hint.pckbd.0.port="0x041"
hint.pckbd.0.irq="1"

# These options are valid for other keyboard drivers as well.
options 	KBD_DISABLE_KEYMAP_LOAD	# refuse to load a keymap
options 	KBD_INSTALL_CDEV	# install a CDEV entry in /dev

# GDC screen
device		gdc
hint.gdc.0.at="isa"
options 	LINE30

#
# The Numeric Processing eXtension driver.  In addition to this, you
# may configure a math emulator (see above).  If your machine has a
# hardware FPU and the kernel configuration includes the npx device
# *and* a math emulator compiled into the kernel, the hardware FPU
# will be used, unless it is found to be broken or unless "flags" to
# npx0 includes "0x08", which requests preference for the emulator.
device		npx

#
# `flags' for npx0:
#	0x01	don't use the npx registers to optimize bcopy.
#	0x02	don't use the npx registers to optimize bzero.
#	0x04	don't use the npx registers to optimize copyin or copyout.
#	0x08	use emulator even if hardware FPU is available.
# The npx registers are normally used to optimize copying and zeroing when
# all of the following conditions are satisfied:
#	I586_CPU is an option
#	the cpu is an i586 (perhaps not a Pentium)
#	the probe for npx0 succeeds
#	INT 16 exception handling works.
# Then copying and zeroing using the npx registers is normally 30-100% faster.
# The flags can be used to control cases where it doesn't work or is slower.
# Setting them at boot time using userconfig works right (the optimizations
# are not used until later in the bootstrap when npx0 is attached).
# Flag 0x08 automatically disables the i586 optimized routines.
#

#
# Optional devices:
#

# 3Dfx Voodoo Graphics, Voodoo II /dev/3dfx CDEV support.  This will create
# the /dev/3dfx0 device to work with glide implementations.  This should get
# linked to /dev/3dfx and /dev/voodoo.  Note that this is not the same as
# the tdfx DRI module from XFree86 and is completely unrelated.
#
# To enable Linuxulator support, one must also include COMPAT_LINUX in the
# config as well, or you will not have the dependencies.  The other option
# is to load both as modules.

device		tdfx			# Enable 3Dfx Voodoo support
options 	TDFX_LINUX		# Enable Linuxulator support

# DRM options:
# mgadrm:    AGP Matrox G200, G400, G450, G550
# r128drm:   ATI Rage 128
# radeondrm: ATI Radeon up to 9000/9100
# sisdrm:    SiS 300/305,540,630
# tdfxdrm:   3dfx Voodoo 3/4/5 and Banshee
# DRM_DEBUG: include debug printfs, very slow
#
# mga requires AGP in the kernel, and it is recommended
# for AGP r128 and radeon cards.

device		mgadrm
device		"r128drm"
device		radeondrm
device		sisdrm
device		tdfxdrm

options 	DRM_DEBUG

#
# Bus mouse
#
device		mse
hint.mse.0.at="isa"
hint.mse.0.port="0x7fd9"
hint.mse.0.irq="13"

#
# Network interfaces:
#

# ar:   Arnet SYNC/570i hdlc sync 2/4 port V.35/X.21 serial driver
#       (requires sppp)
# ed:   Western Digital and SMC 80xx; Novell NE1000 and NE2000; 3Com 3C503
#       HP PC Lan+, various PC Card devices (refer to etc/defaults/pccard.conf)
#       (requires miibus)
# el:   3Com 3C501 (slow!)
# ie:   AT&T StarLAN 10 and EN100; 3Com 3C507; unknown NI5210;
#       Intel EtherExpress
# le:   Digital Equipment EtherWorks 2 and EtherWorks 3 (DEPCA, DE100,
#       DE101, DE200, DE201, DE202, DE203, DE204, DE205, DE422)
# lnc:  Lance/PCnet cards (Isolan, Novell NE2100, NE32-VL, AMD Am7990 and
#       Am79C960)
# oltr: Olicom ISA token-ring adapters OC-3115, OC-3117, OC-3118 and OC-3133.
#       Olicom PCI token-ring adapters OC-3136, OC-3137, OC-3139, OC-3140,
#       OC-3141, OC-3540 and OC-3250.
# rdp:  RealTek RTL 8002-based pocket ethernet adapters
# sbni: Granch SBNI12-xx ISA and PCI adapters
# sr:   RISCom/N2 hdlc sync 1/2 port V.35/X.21 serial driver (requires sppp)
# wl:   Lucent Wavelan (ISA card only).

# Order for ISA/EISA devices is important here

device		ar
hint.ar.0.at="isa"
hint.ar.0.port="0x300"
hint.ar.0.irq="10"
hint.ar.0.maddr="0xd0000"
device		ed
#options 	ED_NO_MIIBUS		# Disable ed miibus support
hint.ed.0.at="isa"
hint.ed.0.port="0x280"
hint.ed.0.irq="5"
hint.ed.0.maddr="0xd8000"
device		el	1
hint.el.0.at="isa"
hint.el.0.port="0x300"
hint.el.0.irq="9"
device		ie			# Hints only required for Starlan
hint.ie.2.at="isa"
hint.ie.2.port="0x300"
hint.ie.2.irq="5"
hint.ie.2.maddr="0xd0000"
device		le	1
hint.le.0.at="isa"
hint.le.0.port="0x300"
hint.le.0.irq="5"
hint.le.0.maddr="0xd0000"
device		lnc
hint.lnc.0.at="isa"
hint.lnc.0.port="0x280"
hint.lnc.0.irq="10"
hint.lnc.0.drq="0"
device		rdp	1
hint.rdp.0.at="isa"
hint.rdp.0.port="0x378"
hint.rdp.0.irq="7"
hint.rdp.0.flags="2"
device		sbni
hint.sbni.0.at="isa"
hint.sbni.0.port="0x210"
hint.sbni.0.irq="0xefdead"
hint.sbni.0.flags="0"
device		snc
hint.snc.0.at="isa"
hint.snc.0.port="0x888"
hint.snc.0.irq="6"
hint.snc.0.maddr="0xc0000"
device		sr
hint.sr.0.at="isa"
hint.sr.0.port="0x300"
hint.sr.0.irq="5"
hint.sr.0.maddr="0xd0000"
device		oltr
hint.oltr.0.at="isa"
device		wl
hint.wl.0.at="isa"
hint.wl.0.port="0x300"
options 	WLCACHE		# enables the signal-strength cache
options 	WLDEBUG		# enables verbose debugging output

#
# SCSI host adapters:
#
# ct: WD33C93[ABC] based SCSI host adapters.
# ncv: NCR 53C500 based SCSI host adapters.
# nsp: Workbit Ninja SCSI-3 based PC Card SCSI host adapters.
# stg: TMC 18C30, 18C50 based SCSI host adapters.

device		ct
hint.ct.0.at="isa"
device		ncv
device		nsp
device		stg
hint.stg.0.at="isa"
hint.stg.0.port="0x140"
hint.stg.0.port="11"

#
# SafeNet crypto driver: can be moved to the MI NOTES as soon as
# it's tested on a big-endian machine
#
device		safe		# SafeNet 1141
options		SAFE_DEBUG	# enable debugging support: hw.safe.debug
options		SAFE_RNDTEST	# enable rndtest support

#####################################################################

#
# Miscellaneous hardware:
#
# wt: Wangtek and Archive QIC-02/QIC-36 tape drives
# ctx: Cortex-I frame grabber
# apm: Laptop Advanced Power Management (experimental)
# pmtimer: Timer device driver for power management events (APM or ACPI)
# spigot: The Creative Labs Video Spigot video-acquisition board
# cy: Cyclades serial driver
# digi: Digiboard driver
# gp:  National Instruments AT-GPIB and AT-GPIB/TNT board, PCMCIA-GPIB
# stl: Stallion EasyIO and EasyConnection 8/32 (cd1400 based)
# stli: Stallion EasyConnection 8/64, ONboard, Brumby (intelligent)

# Notes on APM
#  The flags takes the following meaning for apm0:
#    0x0020  Statclock is broken.

# Notes on the spigot:
#  The video spigot is at 0xad6.  This port address can not be changed.
#  The irq values may only be 10, 11, or 15
#  I/O memory is an 8kb region.  Possible values are:
#    0a0000, 0a2000, ..., 0fffff, f00000, f02000, ..., ffffff
#    The start address must be on an even boundary.
#  Add the following option if you want to allow non-root users to be able
#  to access the spigot.  This option is not secure because it allows users
#  direct access to the I/O page.
#  	options SPIGOT_UNSECURE

# Notes on the Specialix SI/XIO driver:
#  The host card is memory, not IO mapped.
#  The Rev 1 host cards use a 64K chunk, on a 32K boundary.
#  The Rev 2 host cards use a 32K chunk, on a 32K boundary.
#  The cards can use an IRQ of 11, 12 or 15.

# Notes on the Sony Programmable I/O controller
#  This is a temporary driver that should someday be replaced by something
#  that hooks into the ACPI layer.  The device is hooked to the PIIX4's
#  General Device 10 decoder, which means you have to fiddle with PCI
#  registers to map it in, even though it is otherwise treated here as
#  an ISA device.  At the moment, the driver polls, although the device
#  is capable of generating interrupts.  It largely undocumented.
#  The port location in the hint is where you WANT the device to be
#  mapped.  0x10a0 seems to be traditional.  At the moment the jogdial
#  is the only thing truly supported, but apparently a fair percentage
#  of the Vaio extra features are controlled by this device.

# Notes on the Stallion stl and stli drivers:
#  See src/i386/isa/README.stl for complete instructions.
#  This is version 0.0.5alpha, unsupported by Stallion.
#  The stl driver has a secondary IO port hard coded at 0x280.  You need
#     to change src/i386/isa/stallion.c if you reconfigure this on the boards.
#  The "flags" and "msize" settings on the stli driver depend on the board:
#	EasyConnection 8/64 ISA:     flags 23         msize 0x1000
#	EasyConnection 8/64 EISA:    flags 24         msize 0x10000
#	EasyConnection 8/64 MCA:     flags 25         msize 0x1000
#	ONboard ISA:                 flags 4          msize 0x10000
#	ONboard EISA:                flags 7          msize 0x10000
#	ONboard MCA:                 flags 3          msize 0x10000
#	Brumby:                      flags 2          msize 0x4000
#	Stallion:                    flags 1          msize 0x10000

device		wt	1
hint.wt.0.at="isa"
hint.wt.0.port="0x300"
hint.wt.0.irq="5"
hint.wt.0.drq="1"
device		ctx
hint.ctx.0.at="isa"
hint.ctx.0.port="0x230"
hint.ctx.0.maddr="0xd0000"
device		spigot	1
hint.spigot.0.at="isa"
hint.spigot.0.port="0xad6"
hint.spigot.0.irq="15"
hint.spigot.0.maddr="0xee000"
device		apm
hint.apm.0.flags="0x20"
device		canbus
device		canbepm
device		pmc
hint.pmc.0.at="isa"
hint.pmc.0.port="0x8f0"
device		pmtimer			# Adjust system timer at wakeup time
device		cy	1
options 	CY_PCI_FASTINTR		# Use with cy_pci unless irq is shared
hint.cy.0.at="isa"
hint.cy.0.irq="10"
hint.cy.0.maddr="0xd4000"
hint.cy.0.msize="0x2000"
device		digi
hint.digi.0.at="isa"
hint.digi.0.port="0x104"
hint.digi.0.maddr="0xd0000"
# BIOS & FEP/OS components of device digi.
device		digi_CX
device		digi_CX_PCI
device		digi_EPCX
device		digi_EPCX_PCI
device		digi_Xe
device		digi_Xem
device		digi_Xr
device		gp
hint.gp.0.at="isa"
hint.gp.0.port="0x2c0"
device		olpt
hint.olpt.0.at="isa"
hint.olpt.0.port="0x040"
device		stl
hint.stl.0.at="isa"
hint.stl.0.port="0x2a0"
hint.stl.0.irq="10"
device		stli
hint.stli.0.at="isa"
hint.stli.0.port="0x2a0"
hint.stli.0.maddr="0xcc000"
hint.stli.0.flags="23"
hint.stli.0.msize="0x1000"

#
# Laptop/Notebook options:
#
# See also:
#  apm under `Miscellaneous hardware'
# above.

# For older notebooks that signal a powerfail condition (external
# power supply dropped, or battery state low) by issuing an NMI:

options 	POWERFAIL_NMI	# make it beep instead of panicing

#
# PC Card/PCMCIA
# (OLDCARD)
#
# card: pccard slots
# pcic: isa/pccard bridge
device		pcic
hint.pcic.0.at="isa"
#hint.pcic.1.at="isa"
device		card	1

#---------------------------------------------------------------------------
# ISDN4BSD
#
# See /usr/share/examples/isdn/ROADMAP for an introduction to isdn4bsd.
#
# i4b passive ISDN cards support contains the following hardware drivers:
#
#	isic  - Siemens/Infineon ISDN ISAC/HSCX/IPAC chipset driver
#	iwic  - Winbond W6692 PCI bus ISDN S/T interface controller
#	ifpi  - AVM Fritz!Card PCI driver
#	ifpi2  - AVM Fritz!Card PCI version 2 driver
#	ihfc  - Cologne Chip HFC ISA/ISA-PnP chipset driver
#	ifpnp - AVM Fritz!Card PnP driver
#	itjc  - Siemens ISAC / TJNet Tiger300/320 chipset
#
# i4b active ISDN cards support contains the following hardware drivers:
#
#	iavc  - AVM B1 PCI, AVM B1 ISA, AVM T1
#
# Note that the ``options'' (if given) and ``device'' lines must BOTH
# be uncommented to enable support for a given card !
#
# In addition to a hardware driver (and probably an option) the mandatory
# ISDN protocol stack devices and the mandatory support device must be
# enabled as well as one or more devices from the optional devices section.
#
#---------------------------------------------------------------------------
#	isic driver (Siemens/Infineon chipsets)
#
device	isic
#
# PCI bus Cards:
# --------------
#
# ELSA MicroLink ISDN/PCI (same as ELSA QuickStep 1000pro PCI)
options 	ELSA_QS1PCI
#
#---------------------------------------------------------------------------
#	ifpnp driver for AVM Fritz!Card PnP
#
# AVM Fritz!Card PnP
device		ifpnp
#
#---------------------------------------------------------------------------
#	ihfc driver for Cologne Chip ISA chipsets (experimental!)
#
# Teles 16.3c ISA PnP
# AcerISDN P10 ISA PnP
# TELEINT ISDN SPEED No.1
device		ihfc
#
#---------------------------------------------------------------------------
#	ifpi driver for AVM Fritz!Card PCI
#
# AVM Fritz!Card PCI
device		ifpi
#
#---------------------------------------------------------------------------
#	ifpi2 driver for AVM Fritz!Card PCI version 2
#
# AVM Fritz!Card PCI version 2
device		"ifpi2"
#
#---------------------------------------------------------------------------
#	iwic driver for Winbond W6692 chipset
#
# ASUSCOM P-IN100-ST-D (and other Winbond W6692 based cards)
device		iwic
#
#---------------------------------------------------------------------------
#	itjc driver for Siemens ISAC / TJNet Tiger300/320 chipset
#
# Traverse Technologies NETjet-S
# Teles PCI-TJ
device		itjc
#
#---------------------------------------------------------------------------
#	iavc driver (AVM active cards, needs i4bcapi driver!)
#
device		iavc
#
# AVM B1 ISA bus (PnP mode not supported!)
# ----------------------------------------
hint.iavc.0.at="isa"
hint.iavc.0.port="0x150"
hint.iavc.0.irq="5"
#
#---------------------------------------------------------------------------
#	ISDN Protocol Stack - mandatory for all hardware drivers
#
# Q.921 / layer 2 - i4b passive cards D channel handling
device		"i4bq921"
#
# Q.931 / layer 3 - i4b passive cards D channel handling
device		"i4bq931"
#
# layer 4 - i4b common passive and active card handling
device		"i4b"
#
#---------------------------------------------------------------------------
#	ISDN devices - mandatory for all hardware drivers
#
# userland driver to do ISDN tracing (for passive cards only)
device		"i4btrc"	4
#
# userland driver to control the whole thing
device		"i4bctl"
#
#---------------------------------------------------------------------------
#	ISDN devices - optional
#
# userland driver for access to raw B channel
device		"i4brbch"	4
#
# userland driver for telephony
device		"i4btel"	2
#
# network driver for IP over raw HDLC ISDN
device		"i4bipr"	4
# enable VJ header compression detection for ipr i/f
options 	IPR_VJ
# enable logging of the first n IP packets to isdnd (n=32 here)
options 	IPR_LOG=32
#
# network driver for sync PPP over ISDN; requires an equivalent
# number of sppp device to be configured
device		"i4bisppp"	4
#
# B-channel interface to the netgraph subsystem
device		"i4bing"	2
#
# CAPI driver needed for active ISDN cards (see iavc driver above)
device		"i4bcapi"
#
#---------------------------------------------------------------------------

#
# Set the number of PV entries per process.  Increasing this can
# stop panics related to heavy use of shared memory.  However, that can
# (combined with large amounts of physical memory) cause panics at
# boot time due the kernel running out of VM space.
#
# If you're tweaking this, you might also want to increase the sysctls
# "vm.v_free_min", "vm.v_free_reserved", and "vm.v_free_target".
#
# The value below is the one more than the default.
#
options 	PMAP_SHPGPERPROC=201

#
# Change the size of the kernel virtual address space.  Due to
# constraints in loader(8) on i386, this must be a multiple of 4.
# 256 = 1 GB of kernel address space.  Increasing this also causes
# a reduction of the address space in user processes.  512 splits
# the 4GB cpu address space in half (2GB user, 2GB kernel).
#
options 	KVA_PAGES=260


#####################################################################
# ABI Emulation

# Enable iBCS2 runtime support for SCO and ISC binaries
options 	IBCS2

# Emulate spx device for client side of SVR3 local X interface
options 	SPX_HACK

# Enable Linux ABI emulation
options 	COMPAT_LINUX

# Enable i386 a.out binary support
options 	COMPAT_AOUT

# Enable the linux-like proc filesystem support (requires COMPAT_LINUX
# and PSEUDOFS)
options 	LINPROCFS

#
# SysVR4 ABI emulation
#
# The svr4 ABI emulator can be statically compiled into the kernel or loaded as
# a KLD module.
# The STREAMS network emulation code can also be compiled statically or as a
# module.  If loaded as a module, it must be loaded before the svr4 module
# (the /usr/sbin/svr4 script does this for you).  If compiling statically,
# the `streams' device must be configured into any kernel which also
# specifies COMPAT_SVR4.  It is possible to have a statically-configured
# STREAMS device and a dynamically loadable svr4 emulator;  the /usr/sbin/svr4
# script understands that it doesn't need to load the `streams' module under
# those circumstances.
# Caveat:  At this time, `options KTRACE' is required for the svr4 emulator
# (whether static or dynamic).
#
options 	COMPAT_SVR4	# build emulator statically
options 	DEBUG_SVR4	# enable verbose debugging
device		streams		# STREAMS network driver (required for svr4).


#####################################################################
# VM OPTIONS

# Disable the 4 MByte page PSE CPU feature.  The PSE feature allows the
# kernel to use a 4 MByte pages to map the kernel instead of 4k pages.
# This saves on the amount of memory needed for page tables needed to
# map the kernel.  You should only disable this feature as a temporary
# workaround if you are having problems with it enabled.
#
#options 	DISABLE_PSE

# Disable the global pages PGE CPU feature.  The PGE feature allows pages
# to be marked with the PG_G bit.  TLB entries for these pages are not
# flushed from the cache when %cr3 is reloaded.  This can make context
# switches less expensive.  You should only disable this feature as a
# temporary workaround if you are having problems with it enabled.
#
#options 	DISABLE_PG_G

# KSTACK_PAGES is the number of memory pages to assign to the kernel
# stack of each thread.

options 	KSTACK_PAGES=3

#####################################################################

# More undocumented options for linting.
# Note that documenting these are not considered an affront.

options 	FB_INSTALL_CDEV		# install a CDEV entry in /dev

# PECOFF module (Win32 Execution Format)
options 	PECOFF_SUPPORT
options 	PECOFF_DEBUG

options 	ENABLE_ALART
options 	I4B_SMP_WORKAROUND
options 	I586_PMC_GUPROF=0x70000
options 	KBDIO_DEBUG=2
options 	KBD_MAXRETRY=4
options 	KBD_MAXWAIT=6
options 	KBD_RESETDELAY=201

options 	TIMER_FREQ=((14318182+6)/12)

options 	VM_KMEM_SIZE
options 	VM_KMEM_SIZE_MAX
options 	VM_KMEM_SIZE_SCALE


#####################################################################
# Devices we don't want to deal with

nodevice	atkbdc
nodevice	atkbd
nodevice	psm
nodevice	vga
nodevice	bt
nodevice	adw
nodevice	aha
nodevice	ahb
nodevice	ahd
nodevice	mpt
nodevice	trm
nodevice	wds
nodevice	asr
nodevice	dpt
nodevice	ciss
nodevice	iir
nodevice	mly
nodevice	ida		# Compaq Smart RAID
nodevice	mlx		# Mylex DAC960
nodevice	amr		# AMI MegaRAID
nodevice	twe		# 3ware ATA RAID
nodevice	ataraid
nodevice	cm
nodevice	cs
nodevice	ex
nodevice	fea
nodevice	cbb
nodevice	pccard
nodevice	cardbus
nodevice	intpm
nodevice	alpm
nodevice	ichsmb
nodevice	viapm
nodevice	amdpm
nodevice	nfpm


#####################################################################
# Options we don't want to deal with

nooption	VGA_DEBUG
nooption	VGA_WIDTH90
nooption	VGA_SLOW_IOACCESS
nooption	VGA_ALT_SEQACCESS
nooption	PSM_RESETAFTERSUSPEND
nooption	PSM_HOOKRESUME
nooption	ATKBD_DFLT_KEYMAP
nooption	AHD_DEBUG
nooption	AHD_DEBUG_OPTS
nooption	AHD_REG_PRETTY_PRINT
nooption	ADW_ALLOW_MEMIO
nooption	DPT_LOST_IRQ
nooption	DPT_RESET_HBA
nooption	DPT_TIMEOUT_FACTOR
nooption	AAC_DEBUG
nooption	ACPI_MAX_THREADS


#####################################################################
# Make options we don't want to deal with

nomakeoption	ATKBD_DFLT_KEYMAP