am335x-wega.dtsi revision 302408
1/* 2 * Copyright (C) 2015 Phytec Messtechnik GmbH 3 * Author: Teresa Remmet <t.remmet@phytec.de> 4 * 5 * This program is free software; you can redistribute it and/or modify 6 * it under the terms of the GNU General Public License version 2 as 7 * published by the Free Software Foundation. 8 */ 9 10/ { 11 model = "Phytec AM335x phyBOARD-WEGA"; 12 compatible = "phytec,am335x-wega", "phytec,am335x-phycore-som", "ti,am33xx"; 13 14 regulators { 15 compatible = "simple-bus"; 16 17 vcc3v3: fixedregulator@1 { 18 compatible = "regulator-fixed"; 19 regulator-name = "vcc3v3"; 20 regulator-min-microvolt = <3300000>; 21 regulator-max-microvolt = <3300000>; 22 regulator-boot-on; 23 }; 24 }; 25}; 26 27/* CAN Busses */ 28&am33xx_pinmux { 29 dcan1_pins: pinmux_dcan1 { 30 pinctrl-single,pins = < 31 AM33XX_IOPAD(0x968, PIN_OUTPUT_PULLUP | MUX_MODE2) /* uart0_ctsn.d_can1_tx */ 32 AM33XX_IOPAD(0x96c, PIN_INPUT_PULLUP | MUX_MODE2) /* uart0_rtsn.d_can1_rx */ 33 >; 34 }; 35}; 36 37&dcan1 { 38 pinctrl-names = "default"; 39 pinctrl-0 = <&dcan1_pins>; 40 status = "okay"; 41}; 42 43/* Ethernet */ 44&am33xx_pinmux { 45 ethernet1_pins: pinmux_ethernet1 { 46 pinctrl-single,pins = < 47 AM33XX_IOPAD(0x840, PIN_OUTPUT | MUX_MODE1) /* gpmc_a0.mii2_txen */ 48 AM33XX_IOPAD(0x844, PIN_INPUT_PULLDOWN | MUX_MODE1) /* gpmc_a1.mii2_rxdv */ 49 AM33XX_IOPAD(0x848, PIN_OUTPUT | MUX_MODE1) /* gpmc_a2.mii2_txd3 */ 50 AM33XX_IOPAD(0x84c, PIN_OUTPUT | MUX_MODE1) /* gpmc_a3.mii2_txd2 */ 51 AM33XX_IOPAD(0x850, PIN_OUTPUT | MUX_MODE1) /* gpmc_a4.mii2_txd1 */ 52 AM33XX_IOPAD(0x854, PIN_OUTPUT | MUX_MODE1) /* gpmc_a5.mii2_txd0 */ 53 AM33XX_IOPAD(0x858, PIN_INPUT_PULLDOWN | MUX_MODE1) /* gpmc_a6.mii2_txclk */ 54 AM33XX_IOPAD(0x85c, PIN_INPUT_PULLDOWN | MUX_MODE1) /* gpmc_a7.mii2_rxclk */ 55 AM33XX_IOPAD(0x860, PIN_INPUT_PULLDOWN | MUX_MODE1) /* gpmc_a8.mii2_rxd3 */ 56 AM33XX_IOPAD(0x864, PIN_INPUT_PULLDOWN | MUX_MODE1) /* gpmc_a9.mii2_rxd2 */ 57 AM33XX_IOPAD(0x868, PIN_INPUT_PULLDOWN | MUX_MODE1) /* gpmc_a10.mii2_rxd1 */ 58 AM33XX_IOPAD(0x86c, PIN_INPUT_PULLDOWN | MUX_MODE1) /* gpmc_a11.mii2_rxd0 */ 59 AM33XX_IOPAD(0x874, PIN_INPUT_PULLDOWN | MUX_MODE1) /* gpmc_wpn.mii2_rxerr */ 60 AM33XX_IOPAD(0x878, PIN_INPUT_PULLDOWN | MUX_MODE1) /* gpmc_ben1.mii2_col */ 61 >; 62 }; 63}; 64 65&cpsw_emac1 { 66 phy_id = <&davinci_mdio>, <1>; 67 phy-mode = "mii"; 68 dual_emac_res_vlan = <2>; 69}; 70 71&mac { 72 slaves = <2>; 73 pinctrl-names = "default"; 74 pinctrl-0 = <ðernet0_pins ðernet1_pins>; 75 dual_emac = <1>; 76}; 77 78/* MMC */ 79&am33xx_pinmux { 80 mmc1_pins: pinmux_mmc1 { 81 pinctrl-single,pins = < 82 AM33XX_IOPAD(0x8f0, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat3.mmc0_dat3 */ 83 AM33XX_IOPAD(0x8f4, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat2.mmc0_dat2 */ 84 AM33XX_IOPAD(0x8f8, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat1.mmc0_dat1 */ 85 AM33XX_IOPAD(0x8fc, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat0.mmc0_dat0 */ 86 AM33XX_IOPAD(0x900, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_clk.mmc0_clk */ 87 AM33XX_IOPAD(0x904, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_cmd.mmc0_cmd */ 88 AM33XX_IOPAD(0x960, PIN_INPUT_PULLUP | MUX_MODE7) /* spi0_cs1.mmc0_sdcd */ 89 >; 90 }; 91}; 92 93&mmc1 { 94 vmmc-supply = <&vcc3v3>; 95 bus-width = <4>; 96 pinctrl-names = "default"; 97 pinctrl-0 = <&mmc1_pins>; 98 cd-gpios = <&gpio0 6 GPIO_ACTIVE_HIGH>; 99 status = "okay"; 100}; 101 102/* UARTs */ 103&am33xx_pinmux { 104 uart0_pins: pinmux_uart0 { 105 pinctrl-single,pins = < 106 AM33XX_IOPAD(0x970, PIN_INPUT_PULLUP | MUX_MODE0) /* uart0_rxd.uart0_rxd */ 107 AM33XX_IOPAD(0x974, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart0_txd.uart0_txd */ 108 >; 109 }; 110 111 uart1_pins: pinmux_uart1_pins { 112 pinctrl-single,pins = < 113 AM33XX_IOPAD(0x980, PIN_INPUT_PULLUP | MUX_MODE0) /* uart1_rxd.uart1_rxd */ 114 AM33XX_IOPAD(0x984, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart1_txd.uart1_txd */ 115 AM33XX_IOPAD(0x978, PIN_INPUT | MUX_MODE0) /* uart1_ctsn.uart1_ctsn */ 116 AM33XX_IOPAD(0x97c, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart1_rtsn.uart1_rtsn */ 117 >; 118 }; 119}; 120 121&uart0 { 122 pinctrl-names = "default"; 123 pinctrl-0 = <&uart0_pins>; 124 status = "okay"; 125}; 126 127&uart1 { 128 pinctrl-names = "default"; 129 pinctrl-0 = <&uart1_pins>; 130 status = "okay"; 131}; 132 133/* USB */ 134&cppi41dma { 135 status = "okay"; 136}; 137 138&usb_ctrl_mod { 139 status = "okay"; 140}; 141 142&usb { 143 status = "okay"; 144}; 145 146&usb0 { 147 dr_mode = "peripheral"; 148 status = "okay"; 149}; 150 151&usb0_phy { 152 status = "okay"; 153}; 154 155&usb1 { 156 dr_mode = "host"; 157 status = "okay"; 158}; 159 160&usb1_phy { 161 status = "okay"; 162}; 163