nsphyreg.h revision 303975
1/* $NetBSD: nsphyreg.h,v 1.1 1998/08/10 23:58:39 thorpej Exp $ */ 2 3/*- 4 * Copyright (c) 1998 The NetBSD Foundation, Inc. 5 * All rights reserved. 6 * 7 * This code is derived from software contributed to The NetBSD Foundation 8 * by Jason R. Thorpe of the Numerical Aerospace Simulation Facility, 9 * NASA Ames Research Center. 10 * 11 * Redistribution and use in source and binary forms, with or without 12 * modification, are permitted provided that the following conditions 13 * are met: 14 * 1. Redistributions of source code must retain the above copyright 15 * notice, this list of conditions and the following disclaimer. 16 * 2. Redistributions in binary form must reproduce the above copyright 17 * notice, this list of conditions and the following disclaimer in the 18 * documentation and/or other materials provided with the distribution. 19 * 20 * THIS SOFTWARE IS PROVIDED BY THE NETBSD FOUNDATION, INC. AND CONTRIBUTORS 21 * ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED 22 * TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR 23 * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE FOUNDATION OR CONTRIBUTORS 24 * BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR 25 * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF 26 * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS 27 * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN 28 * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) 29 * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE 30 * POSSIBILITY OF SUCH DAMAGE. 31 * 32 * $FreeBSD: releng/11.0/sys/dev/mii/nsphyreg.h 204646 2010-03-03 17:55:51Z joel $ 33 */ 34 35#ifndef _DEV_MII_NSPHYREG_H_ 36#define _DEV_MII_NSPHYREG_H_ 37 38/* 39 * DP83840 registers. 40 */ 41 42#define MII_NSPHY_DCR 0x12 /* Disconnect counter */ 43 44#define MII_NSPHY_FCSCR 0x13 /* False carrier sense counter */ 45 46#define MII_NSPHY_RECR 0x15 /* Receive error counter */ 47 48#define MII_NSPHY_SRR 0x16 /* Silicon revision */ 49 50#define MII_NSPHY_PCR 0x17 /* PCS sub-layer configuration */ 51#define PCR_NRZI 0x8000 /* NRZI encoding enabled for 100TX */ 52#define PCR_DESCRTOSEL 0x4000 /* descrambler t/o select (2ms) */ 53#define PCR_DESCRTODIS 0x2000 /* descrambler t/o disable */ 54#define PCR_REPEATER 0x1000 /* repeater mode */ 55#define PCR_ENCSEL 0x0800 /* encoder mode select */ 56#define PCR_CLK25MDIS 0x0080 /* CLK25M disable */ 57#define PCR_FLINK100 0x0040 /* force good link in 100mbps */ 58#define PCR_CIMDIS 0x0020 /* carrier integrity monitor disable */ 59#define PCR_TXOFF 0x0010 /* force transmit off */ 60#define PCR_LED1MODE 0x0004 /* LED1 mode: see below */ 61#define PCR_LED4MODE 0x0002 /* LED4 mode: see below */ 62 63/* 64 * LED1 Mode: 65 * 66 * 1 LED1 output configured to PAR's CON_STATUS, useful for 67 * network management in 100baseTX mode. 68 * 69 * 0 Normal LED1 operation - 10baseTX and 100baseTX transmission 70 * activity. 71 * 72 * LED4 Mode: 73 * 74 * 1 LED4 output configured to indicate full-duplex in both 75 * 10baseT and 100baseTX modes. 76 * 77 * 0 LED4 output configured to indicate polarity in 10baseT 78 * mode and full-duplex in 100baseTX mode. 79 */ 80 81#define MII_NSPHY_LBREMR 0x18 /* Loopback, bypass, error mask */ 82#define LBREMR_BADSSDEN 0x8000 /* enable bad SSD detection */ 83#define LBREMR_BP4B5B 0x4000 /* bypass 4b/5b encoding */ 84#define LBREMR_BPSCR 0x2000 /* bypass scrambler */ 85#define LBREMR_BPALIGN 0x1000 /* bypass alignment function */ 86#define LBREMR_10LOOP 0x0800 /* 10baseT loopback */ 87#define LBREMR_LB1 0x0200 /* loopback ctl 1 */ 88#define LBREMR_LB0 0x0100 /* loopback ctl 0 */ 89#define LBREMR_ALTCRS 0x0040 /* alt crs operation */ 90#define LBREMR_LOOPXMTDIS 0x0020 /* disable transmit in 100TX loopbk */ 91#define LBREMR_CODEERR 0x0010 /* code errors */ 92#define LBREMR_PEERR 0x0008 /* premature end errors */ 93#define LBREMR_LINKERR 0x0004 /* link errors */ 94#define LBREMR_PKTERR 0x0002 /* packet errors */ 95 96#define MII_NSPHY_PAR 0x19 /* Physical address and status */ 97#define PAR_DISCRSJAB 0x0800 /* disable car sense during jab */ 98#define PAR_ANENSTAT 0x0400 /* autoneg mode status */ 99#define PAR_FEFIEN 0x0100 /* far end fault enable */ 100#define PAR_FDX 0x0080 /* full duplex status */ 101#define PAR_10 0x0040 /* 10mbps mode */ 102#define PAR_CON 0x0020 /* connect status */ 103#define PAR_AMASK 0x001f /* PHY address bits */ 104 105#define MII_NSPHY_10BTSR 0x1b /* 10baseT status */ 106#define MII_NSPHY_10BTCR 0x1c /* 10baseT configuration */ 107 108#endif /* _DEV_MII_NSPHYREG_H_ */ 109