nsphyreg.h revision 50120
1/* $NetBSD: nsphyreg.h,v 1.1 1998/08/10 23:58:39 thorpej Exp $ */ 2 3/*- 4 * Copyright (c) 1998 The NetBSD Foundation, Inc. 5 * All rights reserved. 6 * 7 * This code is derived from software contributed to The NetBSD Foundation 8 * by Jason R. Thorpe of the Numerical Aerospace Simulation Facility, 9 * NASA Ames Research Center. 10 * 11 * Redistribution and use in source and binary forms, with or without 12 * modification, are permitted provided that the following conditions 13 * are met: 14 * 1. Redistributions of source code must retain the above copyright 15 * notice, this list of conditions and the following disclaimer. 16 * 2. Redistributions in binary form must reproduce the above copyright 17 * notice, this list of conditions and the following disclaimer in the 18 * documentation and/or other materials provided with the distribution. 19 * 3. All advertising materials mentioning features or use of this software 20 * must display the following acknowledgement: 21 * This product includes software developed by the NetBSD 22 * Foundation, Inc. and its contributors. 23 * 4. Neither the name of The NetBSD Foundation nor the names of its 24 * contributors may be used to endorse or promote products derived 25 * from this software without specific prior written permission. 26 * 27 * THIS SOFTWARE IS PROVIDED BY THE NETBSD FOUNDATION, INC. AND CONTRIBUTORS 28 * ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED 29 * TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR 30 * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE FOUNDATION OR CONTRIBUTORS 31 * BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR 32 * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF 33 * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS 34 * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN 35 * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) 36 * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE 37 * POSSIBILITY OF SUCH DAMAGE. 38 * 39 * $Id$ 40 */ 41 42#ifndef _DEV_MII_NSPHYREG_H_ 43#define _DEV_MII_NSPHYREG_H_ 44 45/* 46 * DP83840 registers. 47 */ 48 49#define MII_NSPHY_DCR 0x12 /* Disconnect counter */ 50 51#define MII_NSPHY_FCSCR 0x13 /* False carrier sense counter */ 52 53#define MII_NSPHY_RECR 0x15 /* Receive error counter */ 54 55#define MII_NSPHY_SRR 0x16 /* Silicon revision */ 56 57#define MII_NSPHY_PCR 0x17 /* PCS sub-layer configuration */ 58#define PCR_NRZI 0x8000 /* NRZI encoding enabled for 100TX */ 59#define PCR_DESCRTOSEL 0x4000 /* descrambler t/o select (2ms) */ 60#define PCR_DESCRTODIS 0x2000 /* descrambler t/o disable */ 61#define PCR_REPEATER 0x1000 /* repeater mode */ 62#define PCR_ENCSEL 0x0800 /* encoder mode select */ 63#define PCR_CLK25MDIS 0x0080 /* CLK25M disable */ 64#define PCR_FLINK100 0x0040 /* force good link in 100mbps */ 65#define PCR_CIMDIS 0x0020 /* carrier integrity monitor disable */ 66#define PCR_TXOFF 0x0010 /* force transmit off */ 67#define PCR_LED1MODE 0x0004 /* LED1 mode: see below */ 68#define PCR_LED4MODE 0x0002 /* LED4 mode: see below */ 69 70/* 71 * LED1 Mode: 72 * 73 * 1 LED1 output configured to PAR's CON_STATUS, useful for 74 * network management in 100baseTX mode. 75 * 76 * 0 Normal LED1 operation - 10baseTX and 100baseTX transmission 77 * activity. 78 * 79 * LED4 Mode: 80 * 81 * 1 LED4 output configured to indicate full-duplex in both 82 * 10baseT and 100baseTX modes. 83 * 84 * 0 LED4 output configured to indicate polarity in 10baseT 85 * mode and full-duplex in 100baseTX mode. 86 */ 87 88#define MII_NSPHY_LBREMR 0x18 /* Loopback, bypass, error mask */ 89#define LBREMR_BADSSDEN 0x8000 /* enable bad SSD detection */ 90#define LBREMR_BP4B5B 0x4000 /* bypass 4b/5b encoding */ 91#define LBREMR_BPSCR 0x2000 /* bypass scrambler */ 92#define LBREMR_BPALIGN 0x1000 /* bypass alignment function */ 93#define LBREMR_10LOOP 0x0800 /* 10baseT loopback */ 94#define LBREMR_LB1 0x0200 /* loopback ctl 1 */ 95#define LBREMR_LB0 0x0100 /* loopback ctl 0 */ 96#define LBREMR_ALTCRS 0x0040 /* alt crs operation */ 97#define LBREMR_LOOPXMTDIS 0x0020 /* disable transmit in 100TX loopbk */ 98#define LBREMR_CODEERR 0x0010 /* code errors */ 99#define LBREMR_PEERR 0x0008 /* premature end errors */ 100#define LBREMR_LINKERR 0x0004 /* link errors */ 101#define LBREMR_PKTERR 0x0002 /* packet errors */ 102 103#define MII_NSPHY_PAR 0x19 /* Physical address and status */ 104#define PAR_DISCRSJAB 0x0800 /* disable car sense during jab */ 105#define PAR_ANENSTAT 0x0400 /* autoneg mode status */ 106#define PAR_FEFIEN 0x0100 /* far end fault enable */ 107#define PAR_FDX 0x0080 /* full duplex status */ 108#define PAR_10 0x0040 /* 10mbps mode */ 109#define PAR_CON 0x0020 /* connect status */ 110#define PAR_AMASK 0x001f /* PHY address bits */ 111 112#define MII_NSPHY_10BTSR 0x1b /* 10baseT status */ 113#define MII_NSPHY_10BTCR 0x1c /* 10baseT configuration */ 114 115#endif /* _DEV_MII_NSPHYREG_H_ */ 116