e1000_80003es2lan.h revision 169589
1/******************************************************************************* 2 3 Copyright (c) 2001-2007, Intel Corporation 4 All rights reserved. 5 6 Redistribution and use in source and binary forms, with or without 7 modification, are permitted provided that the following conditions are met: 8 9 1. Redistributions of source code must retain the above copyright notice, 10 this list of conditions and the following disclaimer. 11 12 2. Redistributions in binary form must reproduce the above copyright 13 notice, this list of conditions and the following disclaimer in the 14 documentation and/or other materials provided with the distribution. 15 16 3. Neither the name of the Intel Corporation nor the names of its 17 contributors may be used to endorse or promote products derived from 18 this software without specific prior written permission. 19 20 THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" 21 AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE 22 IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE 23 ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE 24 LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR 25 CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF 26 SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS 27 INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN 28 CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) 29 ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE 30 POSSIBILITY OF SUCH DAMAGE. 31 32*******************************************************************************/ 33/*$FreeBSD: head/sys/dev/em/e1000_80003es2lan.h 169589 2007-05-16 00:14:23Z jfv $*/ 34 35 36#ifndef _E1000_80003ES2LAN_H_ 37#define _E1000_80003ES2LAN_H_ 38 39#define E1000_KMRNCTRLSTA_OFFSET_FIFO_CTRL 0x00 40#define E1000_KMRNCTRLSTA_OFFSET_INB_CTRL 0x02 41#define E1000_KMRNCTRLSTA_OFFSET_HD_CTRL 0x10 42 43#define E1000_KMRNCTRLSTA_FIFO_CTRL_RX_BYPASS 0x0008 44#define E1000_KMRNCTRLSTA_FIFO_CTRL_TX_BYPASS 0x0800 45#define E1000_KMRNCTRLSTA_INB_CTRL_DIS_PADDING 0x0010 46 47#define E1000_KMRNCTRLSTA_HD_CTRL_10_100_DEFAULT 0x0004 48#define E1000_KMRNCTRLSTA_HD_CTRL_1000_DEFAULT 0x0000 49 50#define E1000_TCTL_EXT_GCEX_MASK 0x000FFC00 /* Gigabit Carry Extend Padding */ 51#define DEFAULT_TCTL_EXT_GCEX_80003ES2LAN 0x00010000 52 53#define DEFAULT_TIPG_IPGT_1000_80003ES2LAN 0x8 54#define DEFAULT_TIPG_IPGT_10_100_80003ES2LAN 0x9 55 56/* GG82563 PHY Specific Status Register (Page 0, Register 16 */ 57#define GG82563_PSCR_POLARITY_REVERSAL_DISABLE 0x0002 /* 1=Reversal Disabled */ 58#define GG82563_PSCR_CROSSOVER_MODE_MASK 0x0060 59#define GG82563_PSCR_CROSSOVER_MODE_MDI 0x0000 /* 00=Manual MDI */ 60#define GG82563_PSCR_CROSSOVER_MODE_MDIX 0x0020 /* 01=Manual MDIX */ 61#define GG82563_PSCR_CROSSOVER_MODE_AUTO 0x0060 /* 11=Auto crossover */ 62 63/* PHY Specific Control Register 2 (Page 0, Register 26) */ 64#define GG82563_PSCR2_REVERSE_AUTO_NEG 0x2000 65 /* 1=Reverse Auto-Negotiation */ 66 67/* MAC Specific Control Register (Page 2, Register 21) */ 68/* Tx clock speed for Link Down and 1000BASE-T for the following speeds */ 69#define GG82563_MSCR_TX_CLK_MASK 0x0007 70#define GG82563_MSCR_TX_CLK_10MBPS_2_5 0x0004 71#define GG82563_MSCR_TX_CLK_100MBPS_25 0x0005 72#define GG82563_MSCR_TX_CLK_1000MBPS_2_5 0x0006 73#define GG82563_MSCR_TX_CLK_1000MBPS_25 0x0007 74 75#define GG82563_MSCR_ASSERT_CRS_ON_TX 0x0010 /* 1=Assert */ 76 77/* DSP Distance Register (Page 5, Register 26) */ 78#define GG82563_DSPD_CABLE_LENGTH 0x0007 /* 0 = <50M; 79 1 = 50-80M; 80 2 = 80-110M; 81 3 = 110-140M; 82 4 = >140M */ 83 84/* Kumeran Mode Control Register (Page 193, Register 16) */ 85#define GG82563_KMCR_PASS_FALSE_CARRIER 0x0800 86 87/* Max number of times Kumeran read/write should be validated */ 88#define GG82563_MAX_KMRN_RETRY 0x5 89 90/* Power Management Control Register (Page 193, Register 20) */ 91#define GG82563_PMCR_ENABLE_ELECTRICAL_IDLE 0x0001 92 /* 1=Enable SERDES Electrical Idle */ 93 94/* In-Band Control Register (Page 194, Register 18) */ 95#define GG82563_ICR_DIS_PADDING 0x0010 /* Disable Padding */ 96 97#endif 98