RPI-B revision 302408
1# 2# RPI-B -- Custom configuration for the Raspberry Pi 3# 4# For more information on this file, please read the config(5) manual page, 5# and/or the handbook section on Kernel Configuration Files: 6# 7# http://www.FreeBSD.org/doc/en_US.ISO8859-1/books/handbook/kernelconfig-config.html 8# 9# The handbook is also available locally in /usr/share/doc/handbook 10# if you've installed the doc distribution, otherwise always see the 11# FreeBSD World Wide Web server (http://www.FreeBSD.org/) for the 12# latest information. 13# 14# An exhaustive list of options and more detailed explanations of the 15# device lines is also present in the ../../conf/NOTES and NOTES files. 16# If you are in doubt as to the purpose or necessity of a line, check first 17# in NOTES. 18# 19# $FreeBSD: stable/11/sys/arm/conf/RPI-B 298068 2016-04-15 16:05:41Z andrew $ 20 21ident RPI-B 22 23include "std.armv6" 24include "../broadcom/bcm2835/std.rpi" 25include "../broadcom/bcm2835/std.bcm2835" 26 27options INTRNG 28 29options HZ=100 30options SCHED_4BSD # 4BSD scheduler 31options PLATFORM 32 33# Debugging for use in -current 34makeoptions DEBUG=-g # Build kernel with gdb(1) debug symbols 35options ALT_BREAK_TO_DEBUGGER 36#options VERBOSE_SYSINIT # Enable verbose sysinit messages 37options KDB # Enable kernel debugger support 38# For minimum debugger support (stable branch) use: 39#options KDB_TRACE # Print a stack trace for a panic 40# For full debugger support use this instead: 41options DDB # Enable the kernel debugger 42options INVARIANTS # Enable calls of extra sanity checking 43options INVARIANT_SUPPORT # Extra sanity checks of internal structures, required by INVARIANTS 44#options WITNESS # Enable checks to detect deadlocks and cycles 45#options WITNESS_SKIPSPIN # Don't run witness on spinlocks for speed 46#options DIAGNOSTIC 47 48# NFS root from boopt/dhcp 49#options BOOTP 50#options BOOTP_NFSROOT 51#options BOOTP_COMPAT 52#options BOOTP_NFSV3 53#options BOOTP_WIRED_TO=ue0 54 55#options ROOTDEVNAME=\"ufs:mmcsd0s2\" 56 57device bpf 58device loop 59device ether 60device uart 61device pty 62device snp 63device pl011 64 65# Comment following lines for boot console on serial port 66device vt 67device kbdmux 68device ukbd 69 70device sdhci 71device mmc 72device mmcsd 73 74device gpio 75device gpioled 76 77# I2C 78device iic 79device iicbus 80device bcm2835_bsc 81 82device md 83device random # Entropy device 84 85# USB support 86device usb 87options USB_DEBUG 88device dwcotg # DWC OTG controller 89 90# USB storage support 91device scbus 92device da 93device umass 94 95# USB ethernet support 96device smcphy 97device mii 98device smsc 99 100# SPI 101device spibus 102device bcm2835_spi 103 104device vchiq 105device sound 106 107# Flattened Device Tree 108options FDT # Configure using FDT/DTB data 109# Note: DTB is normally loaded and modified by RPi boot loader, then 110# handed to kernel via U-Boot and ubldr. 111#options FDT_DTB_STATIC 112#makeoptions FDT_DTS_FILE=rpi.dts 113makeoptions MODULES_EXTRA=dtb/rpi 114