RPI-B revision 282576
1# 2# RPI-B -- Custom configuration for the Raspberry Pi 3# 4# For more information on this file, please read the config(5) manual page, 5# and/or the handbook section on Kernel Configuration Files: 6# 7# http://www.FreeBSD.org/doc/en_US.ISO8859-1/books/handbook/kernelconfig-config.html 8# 9# The handbook is also available locally in /usr/share/doc/handbook 10# if you've installed the doc distribution, otherwise always see the 11# FreeBSD World Wide Web server (http://www.FreeBSD.org/) for the 12# latest information. 13# 14# An exhaustive list of options and more detailed explanations of the 15# device lines is also present in the ../../conf/NOTES and NOTES files. 16# If you are in doubt as to the purpose or necessity of a line, check first 17# in NOTES. 18# 19# $FreeBSD: head/sys/arm/conf/RPI-B 282576 2015-05-07 12:38:23Z andrew $ 20 21ident RPI-B 22 23include "std.armv6" 24include "../broadcom/bcm2835/std.rpi" 25include "../broadcom/bcm2835/std.bcm2835" 26 27options HZ=100 28options SCHED_4BSD # 4BSD scheduler 29options PLATFORM 30 31# Debugging for use in -current 32makeoptions DEBUG=-g # Build kernel with gdb(1) debug symbols 33options BREAK_TO_DEBUGGER 34options ALT_BREAK_TO_DEBUGGER 35#options VERBOSE_SYSINIT # Enable verbose sysinit messages 36options KDB # Enable kernel debugger support 37# For minimum debugger support (stable branch) use: 38#options KDB_TRACE # Print a stack trace for a panic 39# For full debugger support use this instead: 40options DDB # Enable the kernel debugger 41options INVARIANTS # Enable calls of extra sanity checking 42options INVARIANT_SUPPORT # Extra sanity checks of internal structures, required by INVARIANTS 43#options WITNESS # Enable checks to detect deadlocks and cycles 44#options WITNESS_SKIPSPIN # Don't run witness on spinlocks for speed 45#options DIAGNOSTIC 46 47# NFS root from boopt/dhcp 48#options BOOTP 49#options BOOTP_NFSROOT 50#options BOOTP_COMPAT 51#options BOOTP_NFSV3 52#options BOOTP_WIRED_TO=ue0 53 54#options ROOTDEVNAME=\"ufs:mmcsd0s2\" 55 56device bpf 57device loop 58device ether 59device uart 60device pty 61device snp 62device pl011 63 64# Comment following lines for boot console on serial port 65device vt 66device kbdmux 67device ukbd 68 69device sdhci 70device mmc 71device mmcsd 72 73device gpio 74device gpioled 75 76# I2C 77device iic 78device iicbus 79device bcm2835_bsc 80 81device md 82device random # Entropy device 83 84# USB support 85device usb 86options USB_DEBUG 87device dwcotg # DWC OTG controller 88 89# USB storage support 90device scbus 91device da 92device umass 93 94# USB ethernet support 95device smcphy 96device mii 97device smsc 98 99# SPI 100device spibus 101device bcm2835_spi 102 103device vchiq 104device sound 105 106# Flattened Device Tree 107options FDT # Configure using FDT/DTB data 108# Note: DTB is normally loaded and modified by RPi boot loader, then 109# handed to kernel via U-Boot and ubldr. 110#options FDT_DTB_STATIC 111#makeoptions FDT_DTS_FILE=rpi.dts 112makeoptions MODULES_EXTRA=dtb/rpi 113