$KAME: ndp.8,v 1.28 2002/07/17 08:46:33 itojun Exp $
Copyright (C) 1995, 1996, 1997, and 1998 WIDE Project.
All rights reserved.
Redistribution and use in source and binary forms, with or without
modification, are permitted provided that the following conditions
are met:
1. Redistributions of source code must retain the above copyright
notice, this list of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright
notice, this list of conditions and the following disclaimer in the
documentation and/or other materials provided with the distribution.
3. Neither the name of the project nor the names of its contributors
may be used to endorse or promote products derived from this software
without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE PROJECT AND CONTRIBUTORS ``AS IS'' AND
ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
ARE DISCLAIMED. IN NO EVENT SHALL THE PROJECT OR CONTRIBUTORS BE LIABLE
FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
SUCH DAMAGE.
.Dd May 17, 1998 .Dt NDP 8 .Os
.Sh NAME .Nm ndp .Nd control/diagnose IPv6 neighbor discovery protocol
.Sh SYNOPSIS .Nm ndp .Op Fl nt .Ar hostname .Nm ndp .Op Fl nt .Fl a | Fl c | Fl p .Nm ndp .Op Fl nt .Fl r .Nm ndp .Op Fl nt .Fl H | Fl P | Fl R .Nm ndp .Op Fl nt .Fl A Ar wait .Nm ndp .Op Fl nt .Fl d Ar hostname .Nm ndp .Op Fl nt .Fl f Ar filename .Nm ndp .Op Fl nt .Fl i .Ar interface .Op Ar flags ... .Nm ndp .Op Fl nt .Fl I Op Ar interface | Li delete .Nm ndp .Op Fl nt .Fl s Ar nodename etheraddr .Op Li temp .Op Li proxy
.Sh DESCRIPTION The .Nm command manipulates the address mapping table used by the Neighbor Discovery Protocol (NDP). l -tag -width Ds t Fl a Dump the currently existing NDP entries. The following information will be printed: l -tag -width NeighborXX t Neighbor IPv6 address of the neighbor. t Linklayer Address Linklayer address of the neighbor. It could be .Dq Li (incomplete) when the address is not available. t Netif Network interface associated with the neighbor cache entry. t Expire The time until expiry of the entry. The entry could become .Dq Li permanent , in which case it will never expire. t S State of the neighbor cache entry, as a single letter:
p l -tag -width indent -compact t N Nostate t W Waitdelete t I Incomplete t R Reachable t S Stale t D Delay t P Probe t ? Unknown state (should never happen). .El t Flags Flags on the neighbor cache entry, in a single letter. They are: Router, proxy neighbor advertisement
q Dq p . The field could be followed by a decimal number, which means the number of NS probes the node has sent during the current state. .El t Fl A Ar wait Repeat .Fl a
q dump NDP entries
every
.Ar wait
seconds.
t Fl c Erase all the NDP entries.
t Fl d Delete specified NDP entry.
t Fl f Parse the file specified by
.Ar filename .
t Fl H Harmonize consistency between the routing table and the default router
list; install the top entry of the list into the kernel routing table.
t Fl I Shows the default interface used as the default route when
there is no default router.
t Fl I Ar interface Specifies the default interface used as the default route when
there is no default router.
The
.Ar interface
will be used as the default.
t Fl I Li delete The current default interface will be deleted from the kernel.
t Fl i Ar interface Op Ar flags ... View ND information for the specified interface.
If additional arguments
.Ar flags
are given,
.Nm
sets or clears the specified flags for the interface.
Each flag should be separated by white spaces or tab characters.
Possible flags are as follows.
All of the flags can begin with the
special character
.Ql - ,
which means the flag should be cleared.
Note that you need
.Fl -
before
.Fl foo
in this case.
p l -tag -width Ds -compact t Xo c nud .Xc Turn on or off NUD (Neighbor Unreachability Detection) on the interface. NUD is usually turned on by default. t Xo c accept_rtadv .Xc Specify whether or not to accept Router Advertisement messages received on the .Ar interface . Note that the kernel does not accept Router Advertisement messages unless the .Li net.inet6.ip6.accept_rtadv variable is non-0, even if the flag is on. This flag is set to 1 by default. t Xo c prefer_source .Xc Prefer addresses on the .Ar interface as candidates of the source address for outgoing packets. The default value of this flag is off. For more details about the entire algorithm of source address selection, see the
a IMPLEMENTATION
file supplied with the KAME kit.
.El
t Fl n Do not try to resolve numeric addresses to hostnames.
t Fl p Show prefix list.
t Fl P Flush all the entries in the prefix list.
t Fl r Show default router list.
t Fl R Flush all the entries in the default router list.
t Fl s Register a NDP entry for a node.
The entry will be permanent unless the word
.Li temp
is given in the command.
If the word
.Li proxy
is given, this system will act as an proxy NDP server,
responding to requests for
.Ar hostname
even though the host address is not its own.
t Fl t Print timestamp on each entry,
making it possible to merge output with
.Xr tcpdump 8 .
Most useful when used with
.Fl A .
.El
.Sh RETURN VALUES
The
.Nm
command will exit with 0 on success, and non-zero on errors.
.Sh SEE ALSO
.Xr arp 8
.Sh HISTORY
The
.Nm
command first appeared in the WIDE Hydrangea IPv6 protocol stack kit.
.Sh BUGS
(to be written)