psycho.c revision 182020
1/*- 2 * Copyright (c) 1999, 2000 Matthew R. Green 3 * Copyright (c) 2001 - 2003 by Thomas Moestl <tmm@FreeBSD.org> 4 * Copyright (c) 2005 - 2006 Marius Strobl <marius@FreeBSD.org> 5 * All rights reserved. 6 * 7 * Redistribution and use in source and binary forms, with or without 8 * modification, are permitted provided that the following conditions 9 * are met: 10 * 1. Redistributions of source code must retain the above copyright 11 * notice, this list of conditions and the following disclaimer. 12 * 2. Redistributions in binary form must reproduce the above copyright 13 * notice, this list of conditions and the following disclaimer in the 14 * documentation and/or other materials provided with the distribution. 15 * 3. The name of the author may not be used to endorse or promote products 16 * derived from this software without specific prior written permission. 17 * 18 * THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS'' AND ANY EXPRESS OR 19 * IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES 20 * OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. 21 * IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT, 22 * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, 23 * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; 24 * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED 25 * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, 26 * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY 27 * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF 28 * SUCH DAMAGE. 29 * 30 * from: NetBSD: psycho.c,v 1.39 2001/10/07 20:30:41 eeh Exp 31 */ 32 33#include <sys/cdefs.h> 34__FBSDID("$FreeBSD: head/sys/sparc64/pci/psycho.c 182020 2008-08-22 20:28:19Z marius $"); 35 36/* 37 * Support for `Hummingbird' (UltraSPARC IIe), `Psycho' and `Psycho+' 38 * (UltraSPARC II) and `Sabre' (UltraSPARC IIi) UPA to PCI bridges. 39 */ 40 41#include "opt_ofw_pci.h" 42#include "opt_psycho.h" 43 44#include <sys/param.h> 45#include <sys/systm.h> 46#include <sys/bus.h> 47#include <sys/endian.h> 48#include <sys/kdb.h> 49#include <sys/kernel.h> 50#include <sys/lock.h> 51#include <sys/malloc.h> 52#include <sys/module.h> 53#include <sys/mutex.h> 54#include <sys/pcpu.h> 55#include <sys/reboot.h> 56#include <sys/rman.h> 57 58#include <dev/ofw/ofw_bus.h> 59#include <dev/ofw/ofw_pci.h> 60#include <dev/ofw/openfirm.h> 61 62#include <machine/bus.h> 63#include <machine/bus_common.h> 64#include <machine/bus_private.h> 65#include <machine/iommureg.h> 66#include <machine/iommuvar.h> 67#include <machine/ofw_bus.h> 68#include <machine/resource.h> 69#include <machine/ver.h> 70 71#include <dev/pci/pcireg.h> 72#include <dev/pci/pcivar.h> 73 74#include <sparc64/pci/ofw_pci.h> 75#include <sparc64/pci/psychoreg.h> 76#include <sparc64/pci/psychovar.h> 77 78#include "pcib_if.h" 79 80static const struct psycho_desc *psycho_find_desc(const struct psycho_desc *, 81 const char *); 82static const struct psycho_desc *psycho_get_desc(device_t); 83static void psycho_set_intr(struct psycho_softc *, u_int, bus_addr_t, 84 driver_filter_t, driver_intr_t); 85static int psycho_find_intrmap(struct psycho_softc *, u_int, bus_addr_t *, 86 bus_addr_t *, u_long *); 87static driver_filter_t psycho_dmasync; 88static void psycho_intr_enable(void *); 89static void psycho_intr_disable(void *); 90static void psycho_intr_assign(void *); 91static void psycho_intr_clear(void *); 92static bus_space_tag_t psycho_alloc_bus_tag(struct psycho_softc *, int); 93 94/* Interrupt handlers */ 95static driver_filter_t psycho_ue; 96static driver_filter_t psycho_ce; 97static driver_filter_t psycho_pci_bus; 98static driver_filter_t psycho_powerfail; 99static driver_intr_t psycho_overtemp; 100#ifdef PSYCHO_MAP_WAKEUP 101static driver_filter_t psycho_wakeup; 102#endif 103 104/* IOMMU support */ 105static void psycho_iommu_init(struct psycho_softc *, int, uint32_t); 106 107/* 108 * Methods 109 */ 110static device_probe_t psycho_probe; 111static device_attach_t psycho_attach; 112static bus_read_ivar_t psycho_read_ivar; 113static bus_setup_intr_t psycho_setup_intr; 114static bus_teardown_intr_t psycho_teardown_intr; 115static bus_alloc_resource_t psycho_alloc_resource; 116static bus_activate_resource_t psycho_activate_resource; 117static bus_deactivate_resource_t psycho_deactivate_resource; 118static bus_release_resource_t psycho_release_resource; 119static bus_get_dma_tag_t psycho_get_dma_tag; 120static pcib_maxslots_t psycho_maxslots; 121static pcib_read_config_t psycho_read_config; 122static pcib_write_config_t psycho_write_config; 123static pcib_route_interrupt_t psycho_route_interrupt; 124static ofw_bus_get_node_t psycho_get_node; 125 126static device_method_t psycho_methods[] = { 127 /* Device interface */ 128 DEVMETHOD(device_probe, psycho_probe), 129 DEVMETHOD(device_attach, psycho_attach), 130 DEVMETHOD(device_shutdown, bus_generic_shutdown), 131 DEVMETHOD(device_suspend, bus_generic_suspend), 132 DEVMETHOD(device_resume, bus_generic_resume), 133 134 /* Bus interface */ 135 DEVMETHOD(bus_print_child, bus_generic_print_child), 136 DEVMETHOD(bus_read_ivar, psycho_read_ivar), 137 DEVMETHOD(bus_setup_intr, psycho_setup_intr), 138 DEVMETHOD(bus_teardown_intr, psycho_teardown_intr), 139 DEVMETHOD(bus_alloc_resource, psycho_alloc_resource), 140 DEVMETHOD(bus_activate_resource, psycho_activate_resource), 141 DEVMETHOD(bus_deactivate_resource, psycho_deactivate_resource), 142 DEVMETHOD(bus_release_resource, psycho_release_resource), 143 DEVMETHOD(bus_get_dma_tag, psycho_get_dma_tag), 144 145 /* pcib interface */ 146 DEVMETHOD(pcib_maxslots, psycho_maxslots), 147 DEVMETHOD(pcib_read_config, psycho_read_config), 148 DEVMETHOD(pcib_write_config, psycho_write_config), 149 DEVMETHOD(pcib_route_interrupt, psycho_route_interrupt), 150 151 /* ofw_bus interface */ 152 DEVMETHOD(ofw_bus_get_node, psycho_get_node), 153 154 { 0, 0 } 155}; 156 157static devclass_t psycho_devclass; 158 159DEFINE_CLASS_0(pcib, psycho_driver, psycho_methods, 160 sizeof(struct psycho_softc)); 161DRIVER_MODULE(psycho, nexus, psycho_driver, psycho_devclass, 0, 0); 162 163static SLIST_HEAD(, psycho_softc) psycho_softcs = 164 SLIST_HEAD_INITIALIZER(psycho_softcs); 165 166static const struct intr_controller psycho_ic = { 167 psycho_intr_enable, 168 psycho_intr_disable, 169 psycho_intr_assign, 170 psycho_intr_clear 171}; 172 173struct psycho_icarg { 174 struct psycho_softc *pica_sc; 175 bus_addr_t pica_map; 176 bus_addr_t pica_clr; 177}; 178 179struct psycho_dmasync { 180 struct psycho_softc *pds_sc; 181 driver_filter_t *pds_handler; /* handler to call */ 182 void *pds_arg; /* argument for the handler */ 183 void *pds_cookie; /* parent bus int. cookie */ 184 device_t pds_ppb; /* farest PCI-PCI bridge */ 185 uint8_t pds_bus; /* bus of farest PCI device */ 186 uint8_t pds_slot; /* slot of farest PCI device */ 187 uint8_t pds_func; /* func. of farest PCI device */ 188}; 189 190#define PSYCHO_READ8(sc, off) \ 191 bus_read_8((sc)->sc_mem_res, (off)) 192#define PSYCHO_WRITE8(sc, off, v) \ 193 bus_write_8((sc)->sc_mem_res, (off), (v)) 194#define PCICTL_READ8(sc, off) \ 195 PSYCHO_READ8((sc), (sc)->sc_pcictl + (off)) 196#define PCICTL_WRITE8(sc, off, v) \ 197 PSYCHO_WRITE8((sc), (sc)->sc_pcictl + (off), (v)) 198 199/* 200 * "Sabre" is the UltraSPARC IIi onboard UPA to PCI bridge. It manages a 201 * single PCI bus and does not have a streaming buffer. It often has an APB 202 * (advanced PCI bridge) connected to it, which was designed specifically for 203 * the IIi. The APB let's the IIi handle two independednt PCI buses, and 204 * appears as two "Simba"'s underneath the Sabre. 205 * 206 * "Hummingbird" is the UltraSPARC IIe onboard UPA to PCI bridge. It's 207 * basically the same as Sabre but without an APB underneath it. 208 * 209 * "Psycho" and "Psycho+" are dual UPA to PCI bridges. They sit on the UPA bus 210 * and manage two PCI buses. "Psycho" has two 64-bit 33MHz buses, while 211 * "Psycho+" controls both a 64-bit 33Mhz and a 64-bit 66Mhz PCI bus. You 212 * will usually find a "Psycho+" since I don't think the original "Psycho" 213 * ever shipped, and if it did it would be in the U30. 214 * 215 * Each "Psycho" PCI bus appears as a separate OFW node, but since they are 216 * both part of the same IC, they only have a single register space. As such, 217 * they need to be configured together, even though the autoconfiguration will 218 * attach them separately. 219 * 220 * On UltraIIi machines, "Sabre" itself usually takes pci0, with "Simba" often 221 * as pci1 and pci2, although they have been implemented with other PCI bus 222 * numbers on some machines. 223 * 224 * On UltraII machines, there can be any number of "Psycho+" ICs, each 225 * providing two PCI buses. 226 */ 227 228#define OFW_PCI_TYPE "pci" 229 230struct psycho_desc { 231 const char *pd_string; 232 int pd_mode; 233 const char *pd_name; 234}; 235 236static const struct psycho_desc psycho_compats[] = { 237 { "pci108e,8000", PSYCHO_MODE_PSYCHO, "Psycho compatible" }, 238 { "pci108e,a000", PSYCHO_MODE_SABRE, "Sabre compatible" }, 239 { "pci108e,a001", PSYCHO_MODE_SABRE, "Hummingbird compatible" }, 240 { NULL, 0, NULL } 241}; 242 243static const struct psycho_desc psycho_models[] = { 244 { "SUNW,psycho", PSYCHO_MODE_PSYCHO, "Psycho" }, 245 { "SUNW,sabre", PSYCHO_MODE_SABRE, "Sabre" }, 246 { NULL, 0, NULL } 247}; 248 249static const struct psycho_desc * 250psycho_find_desc(const struct psycho_desc *table, const char *string) 251{ 252 const struct psycho_desc *desc; 253 254 if (string == NULL) 255 return (NULL); 256 for (desc = table; desc->pd_string != NULL; desc++) 257 if (strcmp(desc->pd_string, string) == 0) 258 return (desc); 259 return (NULL); 260} 261 262static const struct psycho_desc * 263psycho_get_desc(device_t dev) 264{ 265 const struct psycho_desc *rv; 266 267 rv = psycho_find_desc(psycho_models, ofw_bus_get_model(dev)); 268 if (rv == NULL) 269 rv = psycho_find_desc(psycho_compats, ofw_bus_get_compat(dev)); 270 return (rv); 271} 272 273static int 274psycho_probe(device_t dev) 275{ 276 const char *dtype; 277 278 dtype = ofw_bus_get_type(dev); 279 if (dtype != NULL && strcmp(dtype, OFW_PCI_TYPE) == 0 && 280 psycho_get_desc(dev) != NULL) { 281 device_set_desc(dev, "U2P UPA-PCI bridge"); 282 return (0); 283 } 284 return (ENXIO); 285} 286 287static int 288psycho_attach(device_t dev) 289{ 290 char name[sizeof("pci108e,1000")]; 291 struct psycho_icarg *pica; 292 struct psycho_softc *asc, *sc, *osc; 293 struct ofw_pci_ranges *range; 294 const struct psycho_desc *desc; 295 bus_addr_t intrclr, intrmap; 296 uint64_t csr, dr; 297 phandle_t child, node; 298 uint32_t dvmabase, prop_array[2]; 299 int32_t rev; 300 u_int ver; 301 int i, n, nrange, rid; 302 303 node = ofw_bus_get_node(dev); 304 sc = device_get_softc(dev); 305 desc = psycho_get_desc(dev); 306 307 sc->sc_node = node; 308 sc->sc_dev = dev; 309 sc->sc_mode = desc->pd_mode; 310 311 /* 312 * The Psycho gets three register banks: 313 * (0) per-PBM configuration and status registers 314 * (1) per-PBM PCI configuration space, containing only the 315 * PBM 256-byte PCI header 316 * (2) the shared Psycho configuration registers 317 */ 318 if (sc->sc_mode == PSYCHO_MODE_PSYCHO) { 319 rid = 2; 320 sc->sc_pcictl = 321 bus_get_resource_start(dev, SYS_RES_MEMORY, 0) - 322 bus_get_resource_start(dev, SYS_RES_MEMORY, 2); 323 switch (sc->sc_pcictl) { 324 case PSR_PCICTL0: 325 sc->sc_half = 0; 326 break; 327 case PSR_PCICTL1: 328 sc->sc_half = 1; 329 break; 330 default: 331 panic("%s: bogus PCI control register location", 332 __func__); 333 /* NOTREACHED */ 334 } 335 } else { 336 rid = 0; 337 sc->sc_pcictl = PSR_PCICTL0; 338 sc->sc_half = 0; 339 } 340 sc->sc_mem_res = bus_alloc_resource_any(dev, SYS_RES_MEMORY, &rid, 341 (sc->sc_mode == PSYCHO_MODE_PSYCHO ? RF_SHAREABLE : 0) | 342 RF_ACTIVE); 343 if (sc->sc_mem_res == NULL) 344 panic("%s: could not allocate registers", __func__); 345 346 /* 347 * Match other Psycho's that are already configured against 348 * the base physical address. This will be the same for a 349 * pair of devices that share register space. 350 */ 351 osc = NULL; 352 SLIST_FOREACH(asc, &psycho_softcs, sc_link) { 353 if (rman_get_start(asc->sc_mem_res) == 354 rman_get_start(sc->sc_mem_res)) { 355 /* Found partner. */ 356 osc = asc; 357 break; 358 } 359 } 360 if (osc == NULL) { 361 sc->sc_mtx = malloc(sizeof(*sc->sc_mtx), M_DEVBUF, 362 M_NOWAIT | M_ZERO); 363 if (sc->sc_mtx == NULL) 364 panic("%s: could not malloc mutex", __func__); 365 mtx_init(sc->sc_mtx, "pcib_mtx", NULL, MTX_SPIN); 366 } else { 367 if (mtx_initialized(osc->sc_mtx) == 0) 368 panic("%s: mutex not initialized", __func__); 369 sc->sc_mtx = osc->sc_mtx; 370 } 371 372 /* Clear PCI AFSR. */ 373 PCICTL_WRITE8(sc, PCR_AFS, PCIAFSR_ERRMASK); 374 375 csr = PSYCHO_READ8(sc, PSR_CS); 376 ver = PSYCHO_GCSR_VERS(csr); 377 sc->sc_ign = 0x1f; /* Hummingbird/Sabre IGN is always 0x1f. */ 378 if (sc->sc_mode == PSYCHO_MODE_PSYCHO) 379 sc->sc_ign = PSYCHO_GCSR_IGN(csr); 380 381 device_printf(dev, "%s, impl %d, version %d, IGN %#x, bus %c\n", 382 desc->pd_name, (u_int)PSYCHO_GCSR_IMPL(csr), ver, sc->sc_ign, 383 'A' + sc->sc_half); 384 385 /* Set up the PCI control and PCI diagnostic registers. */ 386 387 /* 388 * Revision 0 EBus bridges have a bug which prevents them from 389 * working when bus parking is enabled. 390 */ 391 rev = -1; 392 csr = PCICTL_READ8(sc, PCR_CS); 393 csr &= ~PCICTL_ARB_PARK; 394 for (child = OF_child(node); child != 0; child = OF_peer(child)) { 395 if (OF_getprop(child, "name", name, sizeof(name)) == -1) 396 continue; 397 if ((strcmp(name, "ebus") == 0 || 398 strcmp(name, "pci108e,1000") == 0) && 399 OF_getprop(child, "revision-id", &rev, sizeof(rev)) > 0 && 400 rev == 0) 401 break; 402 } 403 if (rev != 0 && OF_getproplen(node, "no-bus-parking") < 0) 404 csr |= PCICTL_ARB_PARK; 405 406 /* Workarounds for version specific bugs. */ 407 dr = PCICTL_READ8(sc, PCR_DIAG); 408 switch (ver) { 409 case 0: 410 dr |= DIAG_RTRY_DIS; 411 dr &= ~DIAG_DWSYNC_DIS; 412 /* XXX need to also disable rerun of the streaming buffers. */ 413 break; 414 case 1: 415 csr &= ~PCICTL_ARB_PARK; 416 dr |= DIAG_RTRY_DIS | DIAG_DWSYNC_DIS; 417 /* XXX need to also disable rerun of the streaming buffers. */ 418 break; 419 default: 420 dr |= DIAG_DWSYNC_DIS; 421 dr &= ~DIAG_RTRY_DIS; 422 break; 423 } 424 425 csr |= PCICTL_SERR | PCICTL_ERRINTEN | PCICTL_ARB_4; 426 csr &= ~(PCICTL_SBHINTEN | PCICTL_WAKEUPEN); 427#ifdef PSYCHO_DEBUG 428 device_printf(dev, "PCI CSR 0x%016llx -> 0x%016llx\n", 429 (unsigned long long)PCICTL_READ8(sc, PCR_CS), 430 (unsigned long long)csr); 431#endif 432 PCICTL_WRITE8(sc, PCR_CS, csr); 433 434 dr &= ~DIAG_ISYNC_DIS; 435#ifdef PSYCHO_DEBUG 436 device_printf(dev, "PCI DR 0x%016llx -> 0x%016llx\n", 437 (unsigned long long)PCICTL_READ8(sc, PCR_DIAG), 438 (unsigned long long)dr); 439#endif 440 PCICTL_WRITE8(sc, PCR_DIAG, dr); 441 442 if (sc->sc_mode == PSYCHO_MODE_SABRE) { 443 /* Use the PROM preset for now. */ 444 csr = PCICTL_READ8(sc, PCR_TAS); 445 if (csr == 0) 446 panic("%s: Hummingbird/Sabre TAS not initialized.", 447 __func__); 448 dvmabase = (ffs(csr) - 1) << PCITAS_ADDR_SHIFT; 449 } else 450 dvmabase = -1; 451 452 /* Initialize memory and I/O rmans. */ 453 sc->sc_pci_io_rman.rm_type = RMAN_ARRAY; 454 sc->sc_pci_io_rman.rm_descr = "Psycho PCI I/O Ports"; 455 if (rman_init(&sc->sc_pci_io_rman) != 0 || 456 rman_manage_region(&sc->sc_pci_io_rman, 0, PSYCHO_IO_SIZE) != 0) 457 panic("%s: failed to set up I/O rman", __func__); 458 sc->sc_pci_mem_rman.rm_type = RMAN_ARRAY; 459 sc->sc_pci_mem_rman.rm_descr = "Psycho PCI Memory"; 460 if (rman_init(&sc->sc_pci_mem_rman) != 0 || 461 rman_manage_region(&sc->sc_pci_mem_rman, 0, PSYCHO_MEM_SIZE) != 0) 462 panic("%s: failed to set up memory rman", __func__); 463 464 nrange = OF_getprop_alloc(node, "ranges", sizeof(*range), 465 (void **)&range); 466 /* 467 * Make sure that the expected ranges are present. The 468 * OFW_PCI_CS_MEM64 one is not currently used though. 469 */ 470 if (nrange != PSYCHO_NRANGE) 471 panic("%s: unsupported number of ranges", __func__); 472 /* 473 * Find the addresses of the various bus spaces. 474 * There should not be multiple ones of one kind. 475 * The physical start addresses of the ranges are the configuration, 476 * memory and I/O handles. 477 */ 478 for (n = 0; n < PSYCHO_NRANGE; n++) { 479 i = OFW_PCI_RANGE_CS(&range[n]); 480 if (sc->sc_pci_bh[i] != 0) 481 panic("%s: duplicate range for space %d", __func__, i); 482 sc->sc_pci_bh[i] = OFW_PCI_RANGE_PHYS(&range[n]); 483 } 484 free(range, M_OFWPROP); 485 486 /* Register the softc, this is needed for paired Psychos. */ 487 SLIST_INSERT_HEAD(&psycho_softcs, sc, sc_link); 488 489 /* 490 * If we're a Hummingbird/Sabre or the first of a pair of Psychos 491 * to arrive here, do the interrupt setup and start up the IOMMU. 492 */ 493 if (osc == NULL) { 494 /* 495 * Hunt through all the interrupt mapping regs and register 496 * our interrupt controller for the corresponding interrupt 497 * vectors. 498 */ 499 for (n = 0; n <= PSYCHO_MAX_INO; n++) { 500 if (psycho_find_intrmap(sc, n, &intrmap, &intrclr, 501 NULL) == 0) 502 continue; 503 pica = malloc(sizeof(*pica), M_DEVBUF, M_NOWAIT); 504 if (pica == NULL) 505 panic("%s: could not allocate interrupt " 506 "controller argument", __func__); 507 pica->pica_sc = sc; 508 pica->pica_map = intrmap; 509 pica->pica_clr = intrclr; 510#ifdef PSYCHO_DEBUG 511 /* 512 * Enable all interrupts and clear all interrupt 513 * states. This aids the debugging of interrupt 514 * routing problems. 515 */ 516 device_printf(dev, 517 "intr map (INO %d, %s) %#lx: %#lx, clr: %#lx\n", 518 n, intrmap <= PSR_PCIB3_INT_MAP ? "PCI" : "OBIO", 519 (u_long)intrmap, (u_long)PSYCHO_READ8(sc, intrmap), 520 (u_long)intrclr); 521 PSYCHO_WRITE8(sc, intrmap, INTMAP_VEC(sc->sc_ign, n)); 522 PSYCHO_WRITE8(sc, intrclr, 0); 523 PSYCHO_WRITE8(sc, intrmap, 524 INTMAP_ENABLE(INTMAP_VEC(sc->sc_ign, n), 525 PCPU_GET(mid))); 526#endif 527 if (intr_controller_register(INTMAP_VEC(sc->sc_ign, n), 528 &psycho_ic, pica) != 0) 529 panic("%s: could not register interrupt " 530 "controller for INO %d", __func__, n); 531 } 532 533 /* 534 * Establish handlers for interesting interrupts... 535 * 536 * XXX We need to remember these and remove this to support 537 * hotplug on the UPA/FHC bus. 538 * 539 * XXX Not all controllers have these, but installing them 540 * is better than trying to sort through this mess. 541 */ 542 psycho_set_intr(sc, 1, PSR_UE_INT_MAP, psycho_ue, NULL); 543 psycho_set_intr(sc, 2, PSR_CE_INT_MAP, psycho_ce, NULL); 544#ifdef DEBUGGER_ON_POWERFAIL 545 psycho_set_intr(sc, 3, PSR_POWER_INT_MAP, psycho_powerfail, 546 NULL); 547#else 548 psycho_set_intr(sc, 3, PSR_POWER_INT_MAP, NULL, 549 (driver_intr_t *)psycho_powerfail); 550#endif 551 /* Psycho-specific initialization */ 552 if (sc->sc_mode == PSYCHO_MODE_PSYCHO) { 553 /* 554 * Hummingbirds/Sabres do not have the following two 555 * interrupts. 556 */ 557 558 /* 559 * The spare hardware interrupt is used for the 560 * over-temperature interrupt. 561 */ 562 psycho_set_intr(sc, 4, PSR_SPARE_INT_MAP, 563 NULL, psycho_overtemp); 564#ifdef PSYCHO_MAP_WAKEUP 565 /* 566 * psycho_wakeup() doesn't do anything useful right 567 * now. 568 */ 569 psycho_set_intr(sc, 5, PSR_PWRMGT_INT_MAP, 570 psycho_wakeup, NULL); 571#endif /* PSYCHO_MAP_WAKEUP */ 572 573 /* Initialize the counter-timer. */ 574 sparc64_counter_init(device_get_nameunit(dev), 575 rman_get_bustag(sc->sc_mem_res), 576 rman_get_bushandle(sc->sc_mem_res), PSR_TC0); 577 } 578 579 /* 580 * Set up IOMMU and PCI configuration if we're the first 581 * of a pair of Psycho's to arrive here. 582 * 583 * We should calculate a TSB size based on amount of RAM 584 * and number of bus controllers and number and type of 585 * child devices. 586 * 587 * For the moment, 32KB should be more than enough. 588 */ 589 sc->sc_is = malloc(sizeof(struct iommu_state), M_DEVBUF, 590 M_NOWAIT | M_ZERO); 591 if (sc->sc_is == NULL) 592 panic("%s: malloc iommu_state failed", __func__); 593 if (sc->sc_mode == PSYCHO_MODE_SABRE) 594 sc->sc_is->is_pmaxaddr = 595 IOMMU_MAXADDR(SABRE_IOMMU_BITS); 596 else 597 sc->sc_is->is_pmaxaddr = 598 IOMMU_MAXADDR(PSYCHO_IOMMU_BITS); 599 sc->sc_is->is_sb[0] = 0; 600 sc->sc_is->is_sb[1] = 0; 601 if (OF_getproplen(node, "no-streaming-cache") < 0) 602 sc->sc_is->is_sb[0] = sc->sc_pcictl + PCR_STRBUF; 603 psycho_iommu_init(sc, 3, dvmabase); 604 } else { 605 /* Just copy IOMMU state, config tag and address. */ 606 sc->sc_is = osc->sc_is; 607 if (OF_getproplen(node, "no-streaming-cache") < 0) 608 sc->sc_is->is_sb[1] = sc->sc_pcictl + PCR_STRBUF; 609 iommu_reset(sc->sc_is); 610 } 611 612 /* 613 * Register a PCI bus error interrupt handler according to which 614 * half this is. Hummingbird/Sabre don't have a PCI bus B error 615 * interrupt but they are also only used for PCI bus A. 616 */ 617 psycho_set_intr(sc, 0, sc->sc_half == 0 ? PSR_PCIAERR_INT_MAP : 618 PSR_PCIBERR_INT_MAP, psycho_pci_bus, NULL); 619 620 /* Allocate our tags. */ 621 sc->sc_pci_memt = psycho_alloc_bus_tag(sc, PCI_MEMORY_BUS_SPACE); 622 sc->sc_pci_iot = psycho_alloc_bus_tag(sc, PCI_IO_BUS_SPACE); 623 sc->sc_pci_cfgt = psycho_alloc_bus_tag(sc, PCI_CONFIG_BUS_SPACE); 624 if (bus_dma_tag_create(bus_get_dma_tag(dev), 8, 0, 625 sc->sc_is->is_pmaxaddr, ~0, NULL, NULL, sc->sc_is->is_pmaxaddr, 626 0xff, 0xffffffff, 0, NULL, NULL, &sc->sc_pci_dmat) != 0) 627 panic("%s: bus_dma_tag_create failed", __func__); 628 /* Customize the tag. */ 629 sc->sc_pci_dmat->dt_cookie = sc->sc_is; 630 sc->sc_pci_dmat->dt_mt = &iommu_dma_methods; 631 632 n = OF_getprop(node, "bus-range", (void *)prop_array, 633 sizeof(prop_array)); 634 if (n == -1) 635 panic("%s: could not get bus-range", __func__); 636 if (n != sizeof(prop_array)) 637 panic("%s: broken bus-range (%d)", __func__, n); 638 if (bootverbose) 639 device_printf(dev, "bus range %u to %u; PCI bus %d\n", 640 prop_array[0], prop_array[1], prop_array[0]); 641 sc->sc_pci_secbus = prop_array[0]; 642 643 /* Clear PCI status error bits. */ 644 PCIB_WRITE_CONFIG(dev, sc->sc_pci_secbus, PCS_DEVICE, PCS_FUNC, 645 PCIR_STATUS, PCIM_STATUS_PERR | PCIM_STATUS_RMABORT | 646 PCIM_STATUS_RTABORT | PCIM_STATUS_STABORT | 647 PCIM_STATUS_PERRREPORT, 2); 648 649 /* 650 * Set the latency timer register as this isn't always done by the 651 * firmware. 652 */ 653 PCIB_WRITE_CONFIG(dev, sc->sc_pci_secbus, PCS_DEVICE, PCS_FUNC, 654 PCIR_LATTIMER, OFW_PCI_LATENCY, 1); 655 656 for (n = PCIR_VENDOR; n < PCIR_STATUS; n += sizeof(uint16_t)) 657 le16enc(&sc->sc_pci_hpbcfg[n], bus_space_read_2( 658 sc->sc_pci_cfgt, sc->sc_pci_bh[OFW_PCI_CS_CONFIG], 659 PSYCHO_CONF_OFF(sc->sc_pci_secbus, PCS_DEVICE, 660 PCS_FUNC, n))); 661 for (n = PCIR_REVID; n <= PCIR_BIST; n += sizeof(uint8_t)) 662 sc->sc_pci_hpbcfg[n] = bus_space_read_1(sc->sc_pci_cfgt, 663 sc->sc_pci_bh[OFW_PCI_CS_CONFIG], PSYCHO_CONF_OFF( 664 sc->sc_pci_secbus, PCS_DEVICE, PCS_FUNC, n)); 665 666 ofw_bus_setup_iinfo(node, &sc->sc_pci_iinfo, sizeof(ofw_pci_intr_t)); 667 /* 668 * On E250 the interrupt map entry for the EBus bridge is wrong, 669 * causing incorrect interrupts to be assigned to some devices on 670 * the EBus. Work around it by changing our copy of the interrupt 671 * map mask to perform a full comparison of the INO. That way 672 * the interrupt map entry for the EBus bridge won't match at all 673 * and the INOs specified in the "interrupts" properties of the 674 * EBus devices will be used directly instead. 675 */ 676 if (strcmp(sparc64_model, "SUNW,Ultra-250") == 0 && 677 sc->sc_pci_iinfo.opi_imapmsk != NULL) 678 *(ofw_pci_intr_t *)(&sc->sc_pci_iinfo.opi_imapmsk[ 679 sc->sc_pci_iinfo.opi_addrc]) = INTMAP_INO_MASK; 680 681 device_add_child(dev, "pci", -1); 682 return (bus_generic_attach(dev)); 683} 684 685static void 686psycho_set_intr(struct psycho_softc *sc, u_int index, bus_addr_t intrmap, 687 driver_filter_t filt, driver_intr_t intr) 688{ 689 u_long vec; 690 int rid; 691 692 rid = index; 693 sc->sc_irq_res[index] = bus_alloc_resource_any(sc->sc_dev, SYS_RES_IRQ, 694 &rid, RF_ACTIVE); 695 if (sc->sc_irq_res[index] == NULL || 696 INTIGN(vec = rman_get_start(sc->sc_irq_res[index])) != sc->sc_ign || 697 INTVEC(PSYCHO_READ8(sc, intrmap)) != vec || 698 intr_vectors[vec].iv_ic != &psycho_ic || 699 bus_setup_intr(sc->sc_dev, sc->sc_irq_res[index], INTR_TYPE_MISC, 700 filt, intr, sc, &sc->sc_ihand[index]) != 0) 701 panic("%s: failed to set up interrupt %d", __func__, index); 702} 703 704static int 705psycho_find_intrmap(struct psycho_softc *sc, u_int ino, bus_addr_t *intrmapptr, 706 bus_addr_t *intrclrptr, bus_addr_t *intrdiagptr) 707{ 708 bus_addr_t intrclr, intrmap; 709 uint64_t diag; 710 int found; 711 712 /* 713 * XXX we only compare INOs rather than INRs since the firmware may 714 * not provide the IGN and the IGN is constant for all devices on 715 * that PCI controller. 716 * This could cause problems for the FFB/external interrupt which 717 * has a full vector that can be set arbitrarily. 718 */ 719 720 if (ino > PSYCHO_MAX_INO) { 721 device_printf(sc->sc_dev, "out of range INO %d requested\n", 722 ino); 723 return (0); 724 } 725 726 found = 0; 727 /* Hunt through OBIO first. */ 728 diag = PSYCHO_READ8(sc, PSR_OBIO_INT_DIAG); 729 for (intrmap = PSR_SCSI_INT_MAP, intrclr = PSR_SCSI_INT_CLR; 730 intrmap <= PSR_PWRMGT_INT_MAP; intrmap += 8, intrclr += 8, 731 diag >>= 2) { 732 if (sc->sc_mode == PSYCHO_MODE_SABRE && 733 (intrmap == PSR_TIMER0_INT_MAP || 734 intrmap == PSR_TIMER1_INT_MAP || 735 intrmap == PSR_PCIBERR_INT_MAP || 736 intrmap == PSR_PWRMGT_INT_MAP)) 737 continue; 738 if (INTINO(PSYCHO_READ8(sc, intrmap)) == ino) { 739 diag &= 2; 740 found = 1; 741 break; 742 } 743 } 744 745 if (!found) { 746 diag = PSYCHO_READ8(sc, PSR_PCI_INT_DIAG); 747 /* Now do PCI interrupts. */ 748 for (intrmap = PSR_PCIA0_INT_MAP, intrclr = PSR_PCIA0_INT_CLR; 749 intrmap <= PSR_PCIB3_INT_MAP; intrmap += 8, intrclr += 32, 750 diag >>= 8) { 751 if (sc->sc_mode == PSYCHO_MODE_PSYCHO && 752 (intrmap == PSR_PCIA2_INT_MAP || 753 intrmap == PSR_PCIA3_INT_MAP)) 754 continue; 755 if (((PSYCHO_READ8(sc, intrmap) ^ ino) & 0x3c) == 0) { 756 intrclr += 8 * (ino & 3); 757 diag = (diag >> ((ino & 3) * 2)) & 2; 758 found = 1; 759 break; 760 } 761 } 762 } 763 if (intrmapptr != NULL) 764 *intrmapptr = intrmap; 765 if (intrclrptr != NULL) 766 *intrclrptr = intrclr; 767 if (intrdiagptr != NULL) 768 *intrdiagptr = diag; 769 return (found); 770} 771 772/* 773 * Interrupt handlers 774 */ 775static int 776psycho_ue(void *arg) 777{ 778 struct psycho_softc *sc = arg; 779 uint64_t afar, afsr; 780 781 afar = PSYCHO_READ8(sc, PSR_UE_AFA); 782 afsr = PSYCHO_READ8(sc, PSR_UE_AFS); 783 /* 784 * On the UltraSPARC-IIi/IIe, IOMMU misses/protection faults cause 785 * the AFAR to be set to the physical address of the TTE entry that 786 * was invalid/write protected. Call into the IOMMU code to have 787 * them decoded to virtual I/O addresses. 788 */ 789 if ((afsr & UEAFSR_P_DTE) != 0) 790 iommu_decode_fault(sc->sc_is, afar); 791 panic("%s: uncorrectable DMA error AFAR %#lx AFSR %#lx", 792 device_get_name(sc->sc_dev), (u_long)afar, (u_long)afsr); 793 return (FILTER_HANDLED); 794} 795 796static int 797psycho_ce(void *arg) 798{ 799 struct psycho_softc *sc = arg; 800 uint64_t afar, afsr; 801 802 mtx_lock_spin(sc->sc_mtx); 803 afar = PSYCHO_READ8(sc, PSR_CE_AFA); 804 afsr = PSYCHO_READ8(sc, PSR_CE_AFS); 805 device_printf(sc->sc_dev, "correctable DMA error AFAR %#lx " 806 "AFSR %#lx\n", (u_long)afar, (u_long)afsr); 807 /* Clear the error bits that we caught. */ 808 PSYCHO_WRITE8(sc, PSR_CE_AFS, afsr & CEAFSR_ERRMASK); 809 mtx_unlock_spin(sc->sc_mtx); 810 return (FILTER_HANDLED); 811} 812 813static int 814psycho_pci_bus(void *arg) 815{ 816 struct psycho_softc *sc = arg; 817 uint64_t afar, afsr; 818 819 afar = PCICTL_READ8(sc, PCR_AFA); 820 afsr = PCICTL_READ8(sc, PCR_AFS); 821 panic("%s: PCI bus %c error AFAR %#lx AFSR %#lx", 822 device_get_name(sc->sc_dev), 'A' + sc->sc_half, (u_long)afar, 823 (u_long)afsr); 824 return (FILTER_HANDLED); 825} 826 827static int 828psycho_powerfail(void *arg) 829{ 830#ifdef DEBUGGER_ON_POWERFAIL 831 struct psycho_softc *sc = arg; 832 833 kdb_enter(KDB_WHY_POWERFAIL, "powerfail"); 834#else 835 static int shutdown; 836 837 /* As the interrupt is cleared we may be called multiple times. */ 838 if (shutdown != 0) 839 return (FILTER_HANDLED); 840 shutdown++; 841 printf("Power Failure Detected: Shutting down NOW.\n"); 842 shutdown_nice(0); 843#endif 844 return (FILTER_HANDLED); 845} 846 847static void 848psycho_overtemp(void *arg) 849{ 850 static int shutdown; 851 852 /* As the interrupt is cleared we may be called multiple times. */ 853 if (shutdown != 0) 854 return; 855 shutdown++; 856 printf("DANGER: OVER TEMPERATURE detected.\nShutting down NOW.\n"); 857 shutdown_nice(RB_POWEROFF); 858} 859 860#ifdef PSYCHO_MAP_WAKEUP 861static int 862psycho_wakeup(void *arg) 863{ 864 struct psycho_softc *sc = arg; 865 866 /* Gee, we don't really have a framework to deal with this properly. */ 867 device_printf(sc->sc_dev, "power management wakeup\n"); 868 return (FILTER_HANDLED); 869} 870#endif /* PSYCHO_MAP_WAKEUP */ 871 872static void 873psycho_iommu_init(struct psycho_softc *sc, int tsbsize, uint32_t dvmabase) 874{ 875 struct iommu_state *is = sc->sc_is; 876 877 /* Punch in our copies. */ 878 is->is_bustag = rman_get_bustag(sc->sc_mem_res); 879 is->is_bushandle = rman_get_bushandle(sc->sc_mem_res); 880 is->is_iommu = PSR_IOMMU; 881 is->is_dtag = PSR_IOMMU_TLB_TAG_DIAG; 882 is->is_ddram = PSR_IOMMU_TLB_DATA_DIAG; 883 is->is_dqueue = PSR_IOMMU_QUEUE_DIAG; 884 is->is_dva = PSR_IOMMU_SVADIAG; 885 is->is_dtcmp = PSR_IOMMU_TLB_CMP_DIAG; 886 887 iommu_init(device_get_nameunit(sc->sc_dev), is, tsbsize, dvmabase, 0); 888} 889 890static int 891psycho_maxslots(device_t dev) 892{ 893 894 /* XXX: is this correct? */ 895 return (PCI_SLOTMAX); 896} 897 898static uint32_t 899psycho_read_config(device_t dev, u_int bus, u_int slot, u_int func, u_int reg, 900 int width) 901{ 902 struct psycho_softc *sc; 903 bus_space_handle_t bh; 904 u_long offset = 0; 905 uint8_t byte; 906 uint16_t shrt; 907 uint32_t r, wrd; 908 int i; 909 910 sc = device_get_softc(dev); 911 bh = sc->sc_pci_bh[OFW_PCI_CS_CONFIG]; 912 913 /* 914 * The Hummingbird and Sabre bridges are picky in that they 915 * only allow their config space to be accessed using the 916 * "native" width of the respective register being accessed 917 * and return semi-random other content of their config space 918 * otherwise. Given that the PCI specs don't say anything 919 * about such a (unusual) limitation and lots of stuff expects 920 * to be able to access the contents of the config space at 921 * any width we allow just that. We do this by using a copy 922 * of the header of the bridge (the rest is all zero anyway) 923 * read during attach (expect for PCIR_STATUS) in order to 924 * simplify things. 925 * The Psycho bridges contain a dupe of their header at 0x80 926 * which we nullify that way also. 927 */ 928 if (bus == sc->sc_pci_secbus && slot == PCS_DEVICE && 929 func == PCS_FUNC) { 930 if (offset % width != 0) 931 return (-1); 932 933 if (reg >= sizeof(sc->sc_pci_hpbcfg)) 934 return (0); 935 936 if ((reg < PCIR_STATUS && reg + width > PCIR_STATUS) || 937 reg == PCIR_STATUS || reg == PCIR_STATUS + 1) 938 le16enc(&sc->sc_pci_hpbcfg[PCIR_STATUS], 939 bus_space_read_2(sc->sc_pci_cfgt, bh, 940 PSYCHO_CONF_OFF(sc->sc_pci_secbus, 941 PCS_DEVICE, PCS_FUNC, PCIR_STATUS))); 942 943 switch (width) { 944 case 1: 945 return (sc->sc_pci_hpbcfg[reg]); 946 case 2: 947 return (le16dec(&sc->sc_pci_hpbcfg[reg])); 948 case 4: 949 return (le32dec(&sc->sc_pci_hpbcfg[reg])); 950 } 951 } 952 953 offset = PSYCHO_CONF_OFF(bus, slot, func, reg); 954 switch (width) { 955 case 1: 956 i = bus_space_peek_1(sc->sc_pci_cfgt, bh, offset, &byte); 957 r = byte; 958 break; 959 case 2: 960 i = bus_space_peek_2(sc->sc_pci_cfgt, bh, offset, &shrt); 961 r = shrt; 962 break; 963 case 4: 964 i = bus_space_peek_4(sc->sc_pci_cfgt, bh, offset, &wrd); 965 r = wrd; 966 break; 967 default: 968 panic("%s: bad width", __func__); 969 /* NOTREACHED */ 970 } 971 972 if (i) { 973#ifdef PSYCHO_DEBUG 974 printf("%s: read data error reading: %d.%d.%d: 0x%x\n", 975 __func__, bus, slot, func, reg); 976#endif 977 r = -1; 978 } 979 return (r); 980} 981 982static void 983psycho_write_config(device_t dev, u_int bus, u_int slot, u_int func, u_int reg, 984 uint32_t val, int width) 985{ 986 struct psycho_softc *sc; 987 bus_space_handle_t bh; 988 u_long offset = 0; 989 990 sc = device_get_softc(dev); 991 offset = PSYCHO_CONF_OFF(bus, slot, func, reg); 992 bh = sc->sc_pci_bh[OFW_PCI_CS_CONFIG]; 993 switch (width) { 994 case 1: 995 bus_space_write_1(sc->sc_pci_cfgt, bh, offset, val); 996 break; 997 case 2: 998 bus_space_write_2(sc->sc_pci_cfgt, bh, offset, val); 999 break; 1000 case 4: 1001 bus_space_write_4(sc->sc_pci_cfgt, bh, offset, val); 1002 break; 1003 default: 1004 panic("%s: bad width", __func__); 1005 /* NOTREACHED */ 1006 } 1007} 1008 1009static int 1010psycho_route_interrupt(device_t bridge, device_t dev, int pin) 1011{ 1012 struct psycho_softc *sc; 1013 struct ofw_pci_register reg; 1014 bus_addr_t intrmap; 1015 ofw_pci_intr_t pintr, mintr; 1016 uint8_t maskbuf[sizeof(reg) + sizeof(pintr)]; 1017 1018 sc = device_get_softc(bridge); 1019 pintr = pin; 1020 if (ofw_bus_lookup_imap(ofw_bus_get_node(dev), &sc->sc_pci_iinfo, ®, 1021 sizeof(reg), &pintr, sizeof(pintr), &mintr, sizeof(mintr), maskbuf)) 1022 return (mintr); 1023 /* 1024 * If this is outside of the range for an intpin, it's likely a full 1025 * INO, and no mapping is required at all; this happens on the U30, 1026 * where there's no interrupt map at the Psycho node. Fortunately, 1027 * there seem to be no INOs in the intpin range on this boxen, so 1028 * this easy heuristics will do. 1029 */ 1030 if (pin > 4) 1031 return (pin); 1032 /* 1033 * Guess the INO; we always assume that this is a non-OBIO 1034 * device, and that pin is a "real" intpin number. Determine 1035 * the mapping register to be used by the slot number. 1036 * We only need to do this on E450s, it seems; here, the slot numbers 1037 * for bus A are one-based, while those for bus B seemingly have an 1038 * offset of 2 (hence the factor of 3 below). 1039 */ 1040 intrmap = PSR_PCIA0_INT_MAP + 1041 8 * (pci_get_slot(dev) - 1 + 3 * sc->sc_half); 1042 mintr = INTINO(PSYCHO_READ8(sc, intrmap)) + pin - 1; 1043 device_printf(bridge, "guessing interrupt %d for device %d.%d pin %d\n", 1044 (int)mintr, pci_get_slot(dev), pci_get_function(dev), pin); 1045 return (mintr); 1046} 1047 1048static int 1049psycho_read_ivar(device_t dev, device_t child, int which, uintptr_t *result) 1050{ 1051 struct psycho_softc *sc; 1052 1053 sc = device_get_softc(dev); 1054 switch (which) { 1055 case PCIB_IVAR_DOMAIN: 1056 *result = device_get_unit(dev); 1057 return (0); 1058 case PCIB_IVAR_BUS: 1059 *result = sc->sc_pci_secbus; 1060 return (0); 1061 } 1062 return (ENOENT); 1063} 1064 1065static int 1066psycho_dmasync(void *arg) 1067{ 1068 struct psycho_dmasync *pds = arg; 1069 1070 (void)PCIB_READ_CONFIG(pds->pds_ppb, pds->pds_bus, pds->pds_slot, 1071 pds->pds_func, PCIR_VENDOR, 2); 1072 (void)PSYCHO_READ8(pds->pds_sc, PSR_DMA_WRITE_SYNC); 1073 return (pds->pds_handler(pds->pds_arg)); 1074} 1075 1076static void 1077psycho_intr_enable(void *arg) 1078{ 1079 struct intr_vector *iv = arg; 1080 struct psycho_icarg *pica = iv->iv_icarg; 1081 1082 PSYCHO_WRITE8(pica->pica_sc, pica->pica_map, 1083 INTMAP_ENABLE(iv->iv_vec, iv->iv_mid)); 1084} 1085 1086static void 1087psycho_intr_disable(void *arg) 1088{ 1089 struct intr_vector *iv = arg; 1090 struct psycho_icarg *pica = iv->iv_icarg; 1091 1092 PSYCHO_WRITE8(pica->pica_sc, pica->pica_map, iv->iv_vec); 1093} 1094 1095static void 1096psycho_intr_assign(void *arg) 1097{ 1098 struct intr_vector *iv = arg; 1099 struct psycho_icarg *pica = iv->iv_icarg; 1100 1101 PSYCHO_WRITE8(pica->pica_sc, pica->pica_map, INTMAP_TID( 1102 PSYCHO_READ8(pica->pica_sc, pica->pica_map), iv->iv_mid)); 1103} 1104 1105static void 1106psycho_intr_clear(void *arg) 1107{ 1108 struct intr_vector *iv = arg; 1109 struct psycho_icarg *pica = iv->iv_icarg; 1110 1111 PSYCHO_WRITE8(pica->pica_sc, pica->pica_clr, 0); 1112} 1113 1114static int 1115psycho_setup_intr(device_t dev, device_t child, struct resource *ires, 1116 int flags, driver_filter_t *filt, driver_intr_t *intr, void *arg, 1117 void **cookiep) 1118{ 1119 struct { 1120 int apb:1; 1121 int ppb:1; 1122 } found; 1123 devclass_t pci_devclass; 1124 device_t cdev, pdev, pcidev; 1125 struct psycho_softc *sc; 1126 struct psycho_dmasync *pds; 1127 u_long vec; 1128 int error; 1129 1130 sc = device_get_softc(dev); 1131 /* 1132 * Make sure the vector is fully specified and we registered 1133 * our interrupt controller for it. 1134 */ 1135 vec = rman_get_start(ires); 1136 if (INTIGN(vec) != sc->sc_ign || 1137 intr_vectors[vec].iv_ic != &psycho_ic) { 1138 device_printf(dev, "invalid interrupt vector 0x%lx\n", vec); 1139 return (EINVAL); 1140 } 1141 1142 /* 1143 * The Sabre-APB-combination has a bug where it does not drain 1144 * DMA write data for devices behind additional PCI-PCI bridges 1145 * underneath the APB PCI-PCI bridge. The workaround is to do 1146 * a read on the farest PCI-PCI bridge followed by a read of the 1147 * PCI DMA write sync register of the Sabre. 1148 * XXX installing the wrapper for an affected device and the 1149 * actual workaround in psycho_dmasync() should be moved to 1150 * psycho(4)-specific bus_dma_tag_create() and bus_dmamap_sync() 1151 * methods, respectively, once DMA tag creation is newbus'ified, 1152 * so the workaround isn't only applied for interrupt handlers 1153 * but also for polling(4) callbacks. 1154 */ 1155 if (sc->sc_mode == PSYCHO_MODE_SABRE) { 1156 pds = malloc(sizeof(*pds), M_DEVBUF, M_NOWAIT | M_ZERO); 1157 if (pds == NULL) 1158 return (ENOMEM); 1159 pcidev = NULL; 1160 found.apb = found.ppb = 0; 1161 pci_devclass = devclass_find("pci"); 1162 for (cdev = child; cdev != dev; cdev = pdev) { 1163 pdev = device_get_parent(cdev); 1164 if (pcidev == NULL) { 1165 if (device_get_devclass(pdev) != pci_devclass) 1166 continue; 1167 pcidev = cdev; 1168 continue; 1169 } 1170 /* 1171 * NB: APB would also match as PCI-PCI bridges. 1172 */ 1173 if (pci_get_vendor(cdev) == 0x108e && 1174 pci_get_device(cdev) == 0x5000) { 1175 found.apb = 1; 1176 break; 1177 } 1178 if (pci_get_class(cdev) == PCIC_BRIDGE && 1179 pci_get_subclass(cdev) == PCIS_BRIDGE_PCI) 1180 found.ppb = 1; 1181 } 1182 if (found.apb && found.ppb && pcidev != NULL) { 1183 pds->pds_sc = sc; 1184 pds->pds_arg = arg; 1185 pds->pds_ppb = 1186 device_get_parent(device_get_parent(pcidev)); 1187 pds->pds_bus = pci_get_bus(pcidev); 1188 pds->pds_slot = pci_get_slot(pcidev); 1189 pds->pds_func = pci_get_function(pcidev); 1190 if (bootverbose) 1191 device_printf(dev, "installed DMA sync " 1192 "workaround for device %d.%d on bus %d\n", 1193 pds->pds_slot, pds->pds_func, 1194 pds->pds_bus); 1195 if (intr == NULL) { 1196 pds->pds_handler = filt; 1197 error = bus_generic_setup_intr(dev, child, 1198 ires, flags, psycho_dmasync, intr, pds, 1199 cookiep); 1200 } else { 1201 pds->pds_handler = (driver_filter_t *)intr; 1202 error = bus_generic_setup_intr(dev, child, 1203 ires, flags, filt, 1204 (driver_intr_t *)psycho_dmasync, pds, 1205 cookiep); 1206 } 1207 } else 1208 error = bus_generic_setup_intr(dev, child, ires, 1209 flags, filt, intr, arg, cookiep); 1210 if (error != 0) { 1211 free(pds, M_DEVBUF); 1212 return (error); 1213 } 1214 pds->pds_cookie = *cookiep; 1215 *cookiep = pds; 1216 return (error); 1217 } 1218 return (bus_generic_setup_intr(dev, child, ires, flags, filt, intr, 1219 arg, cookiep)); 1220} 1221 1222static int 1223psycho_teardown_intr(device_t dev, device_t child, struct resource *vec, 1224 void *cookie) 1225{ 1226 struct psycho_softc *sc; 1227 struct psycho_dmasync *pds; 1228 int error; 1229 1230 sc = device_get_softc(dev); 1231 if (sc->sc_mode == PSYCHO_MODE_SABRE) { 1232 pds = cookie; 1233 error = bus_generic_teardown_intr(dev, child, vec, 1234 pds->pds_cookie); 1235 if (error == 0) 1236 free(pds, M_DEVBUF); 1237 return (error); 1238 } 1239 return (bus_generic_teardown_intr(dev, child, vec, cookie)); 1240} 1241 1242static struct resource * 1243psycho_alloc_resource(device_t bus, device_t child, int type, int *rid, 1244 u_long start, u_long end, u_long count, u_int flags) 1245{ 1246 struct psycho_softc *sc; 1247 struct resource *rv; 1248 struct rman *rm; 1249 bus_space_tag_t bt; 1250 bus_space_handle_t bh; 1251 int needactivate = flags & RF_ACTIVE; 1252 1253 flags &= ~RF_ACTIVE; 1254 1255 sc = device_get_softc(bus); 1256 if (type == SYS_RES_IRQ) { 1257 /* 1258 * XXX: Don't accept blank ranges for now, only single 1259 * interrupts. The other case should not happen with 1260 * the MI PCI code... 1261 * XXX: This may return a resource that is out of the 1262 * range that was specified. Is this correct...? 1263 */ 1264 if (start != end) 1265 panic("%s: XXX: interrupt range", __func__); 1266 start = end = INTMAP_VEC(sc->sc_ign, end); 1267 return (BUS_ALLOC_RESOURCE(device_get_parent(bus), child, type, 1268 rid, start, end, count, flags)); 1269 } 1270 switch (type) { 1271 case SYS_RES_MEMORY: 1272 rm = &sc->sc_pci_mem_rman; 1273 bt = sc->sc_pci_memt; 1274 bh = sc->sc_pci_bh[OFW_PCI_CS_MEM32]; 1275 break; 1276 case SYS_RES_IOPORT: 1277 rm = &sc->sc_pci_io_rman; 1278 bt = sc->sc_pci_iot; 1279 bh = sc->sc_pci_bh[OFW_PCI_CS_IO]; 1280 break; 1281 default: 1282 return (NULL); 1283 /* NOTREACHED */ 1284 } 1285 1286 rv = rman_reserve_resource(rm, start, end, count, flags, child); 1287 if (rv == NULL) 1288 return (NULL); 1289 rman_set_rid(rv, *rid); 1290 bh += rman_get_start(rv); 1291 rman_set_bustag(rv, bt); 1292 rman_set_bushandle(rv, bh); 1293 1294 if (needactivate) { 1295 if (bus_activate_resource(child, type, *rid, rv)) { 1296 rman_release_resource(rv); 1297 return (NULL); 1298 } 1299 } 1300 return (rv); 1301} 1302 1303static int 1304psycho_activate_resource(device_t bus, device_t child, int type, int rid, 1305 struct resource *r) 1306{ 1307 void *p; 1308 int error; 1309 1310 if (type == SYS_RES_IRQ) 1311 return (BUS_ACTIVATE_RESOURCE(device_get_parent(bus), child, 1312 type, rid, r)); 1313 if (type == SYS_RES_MEMORY) { 1314 /* 1315 * Need to memory-map the device space, as some drivers depend 1316 * on the virtual address being set and useable. 1317 */ 1318 error = sparc64_bus_mem_map(rman_get_bustag(r), 1319 rman_get_bushandle(r), rman_get_size(r), 0, 0, &p); 1320 if (error != 0) 1321 return (error); 1322 rman_set_virtual(r, p); 1323 } 1324 return (rman_activate_resource(r)); 1325} 1326 1327static int 1328psycho_deactivate_resource(device_t bus, device_t child, int type, int rid, 1329 struct resource *r) 1330{ 1331 1332 if (type == SYS_RES_IRQ) 1333 return (BUS_DEACTIVATE_RESOURCE(device_get_parent(bus), child, 1334 type, rid, r)); 1335 if (type == SYS_RES_MEMORY) { 1336 sparc64_bus_mem_unmap(rman_get_virtual(r), rman_get_size(r)); 1337 rman_set_virtual(r, NULL); 1338 } 1339 return (rman_deactivate_resource(r)); 1340} 1341 1342static int 1343psycho_release_resource(device_t bus, device_t child, int type, int rid, 1344 struct resource *r) 1345{ 1346 int error; 1347 1348 if (type == SYS_RES_IRQ) 1349 return (BUS_RELEASE_RESOURCE(device_get_parent(bus), child, 1350 type, rid, r)); 1351 if (rman_get_flags(r) & RF_ACTIVE) { 1352 error = bus_deactivate_resource(child, type, rid, r); 1353 if (error) 1354 return (error); 1355 } 1356 return (rman_release_resource(r)); 1357} 1358 1359static bus_dma_tag_t 1360psycho_get_dma_tag(device_t bus, device_t child) 1361{ 1362 struct psycho_softc *sc; 1363 1364 sc = device_get_softc(bus); 1365 return (sc->sc_pci_dmat); 1366} 1367 1368static phandle_t 1369psycho_get_node(device_t bus, device_t dev) 1370{ 1371 struct psycho_softc *sc; 1372 1373 sc = device_get_softc(bus); 1374 /* We only have one child, the PCI bus, which needs our own node. */ 1375 return (sc->sc_node); 1376} 1377 1378static bus_space_tag_t 1379psycho_alloc_bus_tag(struct psycho_softc *sc, int type) 1380{ 1381 bus_space_tag_t bt; 1382 1383 bt = malloc(sizeof(struct bus_space_tag), M_DEVBUF, M_NOWAIT | M_ZERO); 1384 if (bt == NULL) 1385 panic("%s: out of memory", __func__); 1386 1387 bt->bst_cookie = sc; 1388 bt->bst_parent = rman_get_bustag(sc->sc_mem_res); 1389 bt->bst_type = type; 1390 return (bt); 1391} 1392