if_xereg.h revision 48117
1/*- 2 * Copyright (c) 1998, 1999 Scott Mitchell 3 * All rights reserved. 4 * 5 * Redistribution and use in source and binary forms, with or without 6 * modification, are permitted provided that the following conditions 7 * are met: 8 * 1. Redistributions of source code must retain the above copyright 9 * notice, this list of conditions and the following disclaimer. 10 * 2. Redistributions in binary form must reproduce the above copyright 11 * notice, this list of conditions and the following disclaimer in the 12 * documentation and/or other materials provided with the distribution. 13 * 14 * THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND 15 * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE 16 * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE 17 * ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE 18 * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL 19 * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS 20 * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) 21 * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT 22 * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY 23 * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF 24 * SUCH DAMAGE. 25 * 26 * $Id: if_xereg.h,v 1.5 1999/05/20 21:53:58 scott Exp $ 27 * $FreeBSD: head/sys/dev/xe/if_xereg.h 48117 1999-06-22 19:19:46Z obrien $ 28 */ 29 30/* 31 * Register definitions for Xircom PCMCIA Ethernet controllers, based on 32 * Rev. B of the "Dingo" 10/100 controller used in Xircom CEM56 and RealPort 33 * Ethernet/modem cards. The Dingo can be configured to be register 34 * compatible with the "Mohawk" 10/100 controller used in Xircom CE3 cards 35 * (also some Intel and Compaq OEM versions of the CE3). The older 10Mbps CE2 36 * cards seem to use earlier revisions of the same device. Some registers and 37 * bits below are marked 'CE2 only'; these are used by Werner Koch's xirc2ps 38 * driver that was originally for the CE2 but, according to the spec, aren't 39 * present on the Dingo. They often seem to relate to operation on coax 40 * cables, which Mohawk can do in theory (it has the SSI interface) so they 41 * _might_ also work on Mohawk. I've also noted the few registers that are 42 * specific to Dingo. 43 * 44 * As far as I can tell, the Dingo is basically a Mohawk device with a few 45 * registers and support for a second PCMCIA function (the modem) added. In 46 * Dingo mode the SSI (non-MII) PHY interface of the Mohawk is not available. 47 * The CE2 chip is most likely a Mohawk without the MII and definitely with a 48 * slightly different register set. 49 * 50 * In all cases, the controller uses a paged model of register access. The 51 * first eight registers are always the same, the function of the second eight 52 * is selected by the value in the Page Register (reg 0x01). 53 * 54 * References: 55 * 1. Dingo External Reference Specification, Revision B. Xircom Inc., 56 * Thousand Oaks, California. August 1998. Available under licence from 57 * Xircom, http://www.xircom.com/ 58 * 2. ML6692 100BASE-TX Physical Layer with MII specification. MicroLinear 59 * Corp, San Jose, California. May 1997. Available for download from 60 * http://www.microlinear.com/ 61 * 3. DP83840 10/100 Mb/s Ethernet Physical Layer specification. National 62 * Semiconductor Corp., Arlington, Texas. March 1997. Available for 63 * download from http://www.ns.com/ 64 * 4. Werner Koch's xirc2ps driver for Linux, for all the CE2 and CE3 frobs 65 * that aren't documented in the Xircom spec. Available for download from 66 * http://www.d.shuttle.de/isil/xircom/xirc2ps.html 67 */ 68 69#include "xe.h" 70#if NXE > 0 71 72 73 74/******************* 75 * PCMCIA registers 76 *******************/ 77 78/* 79 * These are probably Dingo-specific, but you won't need them unless you have 80 * a CEM card that needs a bit of hackery to get the Ethernet function to 81 * operate. All addresses are in card attribute space. 82 */ 83#define DINGO_CIS 0x0000 /* Start of CIS tuples */ 84#define DINGO_ETH 0x0800 /* Ethernet configuration registers */ 85#define DINGO_COR 0x0820 /* Dingo configuration option registers */ 86#define DINGO_2ND 0x0840 /* 2nd function configuration registers */ 87 88 89/* 90 * Ethernet configuration registers 91 */ 92#define DINGO_ECOR (DINGO_ETH+0) /* Ethernet Configuration Option Register */ 93#define DINGO_ECSR (DINGO_ETH+2) /* Ethernet Configuration Status Register */ 94#define DINGO_EBAR0 (DINGO_ETH+10) /* Ethernet Base Address Register bits 7:4 (3:0 always 0) */ 95#define DINGO_EBAR1 (DINGO_ETH+12) /* Ethernet Base Address Register bits 15:8 */ 96 97/* DINGO_ECOR bits */ 98#define DINGO_ECOR_ETH_ENABLE 0x01 /* 1 = Enable Ethernet part of adapter */ 99#define DINGO_ECOR_IOB_ENABLE 0x02 /* 1 = Enable EBAR, else use INDEX bits */ 100#define DINGO_ECOR_INT_ENABLE 0x04 /* 1 = Enable Ethernet interrupts */ 101#define DINGO_ECOR_IOB_INDEX 0x18 /* 00 = 0x300; 01 = 0x310; 10 = 0x320; 11 = no IO base */ 102#define DINGO_ECOR_IOB_SHIFT 0x03 103#define DINGO_ECOR_IRQ_STSCHG 0x20 /* 1 = Route interrupts to -STSCHG pin, else use -INT pin */ 104#define DINGO_ECOR_IRQ_LEVEL 0x40 /* 1 = Level-triggered interrupts, else edge-triggered */ 105#define DINGO_ECOR_SRESET 0x80 /* 1 = Soft reset Ethernet adpater. Must write to 0 */ 106 107/* DINGO_ECSR bits */ 108#define DINGO_ECSR_INT_ACK 0x01 /* 1 = Host must acknowledge interrupts (Clear ECSR_INT bit) */ 109#define DINGO_ECSR_INT 0x02 /* 1 = Interrupt service requested */ 110#define DINGO_ECSR_POWER_DOWN 0x04 /* 1 = Power down Ethernet adapter */ 111 112/* 113 * EBAR0/EBAR1 set the I/O base address of the Ethernet adapter when 114 * ECOR_IOB_ENABLE is set. 12 significant bits. 115 */ 116 117 118/* 119 * Dingo configuration registers 120 */ 121#define DINGO_DCOR0 (DINGO_COR+0) /* Dingo Configuration Options Register 0 */ 122#define DINGO_DCOR1 (DINGO_COR+2) /* Dingo Configuration Options Register 1 */ 123#define DINGO_DCOR2 (DINGO_COR+4) /* Dingo Configuration Options Register 2 */ 124#define DINGO_DCOR3 (DINGO_COR+6) /* Dingo Configuration Options Register 3 */ 125#define DINGO_DCOR4 (DINGO_COR+8) /* Dingo Configuration Options Register 4 */ 126 127/* DINGO_DCOR0 bits */ 128#define DINGO_DCOR0_SF_INT 0x01 /* 1 = Enable 2ndF interrupts (alternate to SFCOR:2) */ 129#define DINGO_DCOR0_DECODE 0x04 /* 1 = Decode 2ndF interrupts in Dingo, else in 2ndF */ 130#define DINGO_DCOR0_BUS 0x08 /* 1 = 2ndF bus is ISA, else PCMCIA */ 131#define DINGO_DCOR0_LED3_POWER 0x10 /* 1 = Drive LED3 line from SFCSR:2 */ 132#define DINGO_DCOR0_LED3_RESET 0x20 /* 1 = Drive LED3 line from SFCOR:7 */ 133#define DINGO_DCOR0_MR_POWER 0x40 /* 1 = Drive MRESET line from SFCSR:2 */ 134#define DINGO_DCOR0_MR_RESET 0x80 /* 1 = Drive MRESET line from SFCOR:7 */ 135 136/* DINGO_DCOR1 bits */ 137#define DINGO_DCOR1_INT_STSCHG 0x01 /* 1 = Route 2ndF interrupts to -STSCHG (alternate to SFCOR:5) */ 138#define DINGO_DCOR1_MSTSCHG 0x02 /* 1 = Route 2ndF -MSTSCHG line to -STSCHG */ 139#define DINGO_DCOR1_EEDIO 0x04 /* 1 = Use EEDIO pin as data line 6 to 2ndF */ 140#define DINGO_DCOR1_INT_LEVEL 0x08 /* 1 = Force level-triggered interrupts from 2ndF */ 141#define DINGO_DCOR1_SHADOW_CSR 0x10 /* Reserved, always write 0 */ 142#define DINGO_DCOR1_SHADOW_IOB 0x20 /* Reserved, always write 0 */ 143#define DINGO_DCOR1_CSR_WAIT 0xC0 /* Reserved, always write 0 */ 144#define DINGO_DCOR1_CSR_SHIFT 0x06 145 146/* DINGO_DCOR2 bits */ 147#define DINGO_DCOR2_SHM_BASE 0x0f /* Bits 15-12 of Ethernet shared memory window */ 148#define DINGO_DCOR2_SHM_SHIFT 0x00 149#define DINGO_DCOR2_SHADOW_COR 0x10 /* Reserved, always write 0 */ 150 151/* 152 * DCOR3/DCOR4 configure Dingo to assert -IOIS16 on any access to each pair of 153 * ports in the range SFIOB+0 .. SFIOB+31. Each pair can be set individually, 154 * eg. DCOR3:0 enables this function on ports SFIOB+0 and SFIOB+1. 155 */ 156 157 158/* 159 * Second function configuration registers 160 */ 161#define DINGO_SFCOR (DINGO_2ND+0) /* 2nd Function Configuration Option Register */ 162#define DINGO_SFCSR (DINGO_2ND+2) /* 2nd Function Configuration Status Register */ 163#define DINGO_SFBAR0 (DINGO_2ND+10) /* 2nd Function Base Address Register bits 7:0 */ 164#define DINGO_SFBAR1 (DINGO_2ND+12) /* 2nd Function Base Address Register bits 15:8 */ 165#define DINGO_SFILR (DINGO_2ND+18) /* 2nd Function I/O Limit Register */ 166 167/* DINGO_SFCOR bits */ 168#define DINGO_SFCOR_SF_ENABLE 0x01 /* 1 = Enable second fuction */ 169#define DINGO_SFCOR_IOB_ENABLE 0x02 /* 1 = Enable SFBAR, else use COM_SELECT bits */ 170#define DINGO_SFCOR_INT_ENABLE 0x04 /* 1 = Enable second function interrupts */ 171#define DINGO_SFCOR_COM_SELECT 0x18 /* 00 = 0x3f8; 01 = 0x2f8; 10 = 0x3e8; 11 = 0x2e8 */ 172#define DINGO_SFCOR_COM_SHIFT 0x03 173#define DINGO_SFCOR_IRQ_STSCHG 0x20 /* 1 = Route interrupts to -STSCHG pin, else use -INT pin */ 174#define DINGO_SFCOR_IRQ_LEVEL 0x40 /* 1 = Level-triggered interrupts, else edge-triggered */ 175#define DINGO_SFCOR_SRESET 0x80 /* 1 = Soft reset second function. Must write to 0 */ 176 177/* DINGO_SFCSR bits */ 178#define DINGO_SFCSR_INT_ACK 0x01 /* 1 = Host must acknowledge interrupts (Clear SFCSR_INT bit) */ 179#define DINGO_SFCSR_INT 0x02 /* 1 = Interrupt service requested */ 180#define DINGO_SFCSR_POWER_DOWN 0x04 /* 1 = Power down second function */ 181 182/* 183 * SFBAR0/SFBAR1 set the I/O base address of the second function when 184 * SFCOR_IOB_ENABLE is set. 16 significant bits. 185 */ 186 187/* 188 * SFILR is a bitmap of address lines 7:0 decoded by the second function 189 * device. Eg. a device with 16 ports should write 0x0f to this register. 190 */ 191 192 193 194/******************************** 195 * Ethernet controller registers 196 ********************************/ 197 198/* 199 * Common registers (available from any register page) 200 * 201 * Note: The EDP is actually 32 bits wide, occupying registers 2-5. In PCMCIA 202 * operation we can only access 16 bits at once, through registers 4 & 5. 203 */ 204#define XE_CR 0x00 /* Command register (write) */ 205#define XE_ESR 0x00 /* Ethernet status register (read) */ 206#define XE_PR 0x01 /* Page select register */ 207#define XE_EDP 0x04 /* Ethernet data port */ 208#define XE_ISR 0x06 /* Ethernet interrupt status register (read) */ 209#define XE_GIR 0x07 /* Global interrupt register (Dingo only) */ 210 211/* XE_CR bits */ 212#define XE_CR_TX_PACKET 0x01 /* Transmit packet */ 213#define XE_CR_SOFT_RESET 0x02 /* Software reset */ 214#define XE_CR_ENABLE_INTR 0x04 /* Enable interrupts */ 215#define XE_CR_FORCE_INTR 0x08 /* Force an interrupt */ 216#define XE_CR_CLEAR_FIFO 0x10 /* Clear FIFO after transmit overrun */ 217#define XE_CR_CLEAR_OVERRUN 0x20 /* Clear receive overrun condition */ 218#define XE_CR_RESTART_TX 0x40 /* Restart TX after 16 collisions or TX underrun */ 219 220/* XE_ESR bits */ 221#define XE_ESR_FULL_PACKET_RX 0x01 /* At least one full packet received */ 222#define XE_ESR_PART_PACKET_RX 0x02 /* At least 64 bytes of packet received */ 223#define XE_ESR_REJECT_PACKET 0x04 /* Partial packet rejected */ 224#define XE_ESR_TX_PENDING 0x08 /* At least one packet waiting to transmit */ 225#define XE_ESR_BAD_POLARITY 0x10 /* Bad cable polarity? (CE2 only) */ 226#define XE_ESR_MEDIA_SELECT 0x20 /* SSI(?) media select: 1 = Twisted pair; 0 = AUI */ 227 228/* XE_ISR bits */ 229#define XE_ISR_TX_OVERFLOW 0x01 /* No space in transmit buffer */ 230#define XE_ISR_TX_PACKET 0x02 /* Packet sent successfully */ 231#define XE_ISR_MAC_INTR 0x04 /* Some kind of MAC interrupt happened */ 232#define XE_ISR_RX_EARLY 0x10 /* Incoming packet in early receive mode */ 233#define XE_ISR_RX_PACKET 0x20 /* Complete packet received successfully */ 234#define XE_ISR_RX_REJECT 0x40 /* Partial incoming packet rejected by MAC */ 235#define XE_ISR_FORCE_INTR 0x80 /* Interrupt forced */ 236 237/* XE_GIR bits */ 238#define XE_GIR_ETH_IRQ 0x01 /* Ethernet IRQ pending */ 239#define XE_GIR_ETH_MASK 0x02 /* 1 = Mask Ethernet interrupts to host */ 240#define XE_GIR_SF_IRQ 0x04 /* Second function IRQ pending */ 241#define XE_GIR_SF_MASK 0x08 /* 1 = Mask second function interrupts to host */ 242 243 244/* 245 * Page 0 registers 246 */ 247#define XE_TSO 0x08 /* Transmit space open (17 bits) */ 248#define XE_TRS 0x0a /* Transmit reservation size (CE2 only, removed in rev. 1) */ 249#define XE_DO 0x0c /* Data offset register (13 bits/3 flags, write) */ 250#define XE_RSR 0x0c /* Receive status register (read) */ 251#define XE_TPR 0x0d /* Packets transmitted register (read) */ 252#define XE_RBC 0x0e /* Received byte count (13 bits/3 flags, read) */ 253 254/* XE_DO bits */ 255#define XE_DO_OFFSET 0x1fff /* First byte fetched when CHANGE_OFFSET issued */ 256#define XE_DO_OFFSET_SHIFT 0x00 257#define XE_DO_CHANGE_OFFSET 0x2000 /* Flush RX FIFO, start fetching from OFFSET */ 258#define XE_DO_SHARED_MEM 0x4000 /* Enable shared memory mode */ 259#define XE_DO_SKIP_RX_PACKET 0x8000 /* Skip to next packet in buffer memory */ 260 261/* XE_RSR bits */ 262#define XE_RSR_PHYS_PACKET 0x01 /* 1 = Physical packet, 0 = Multicast packet */ 263#define XE_RSR_BCAST_PACKET 0x02 /* Broadcast packet */ 264#define XE_RSR_LONG_PACKET 0x04 /* Packet >1518 bytes */ 265#define XE_RSR_ADDR_MATCH 0x08 /* Packet matched one of our node addresses */ 266#define XE_RSR_ALIGN_ERROR 0x10 /* Bad alignment? (CE2 only) */ 267#define XE_RSR_CRC_ERROR 0x20 /* Incorrect CRC */ 268#define XE_RSR_RX_OK 0x80 /* No errors on received packet */ 269 270/* XE_RBC bits */ 271#define XE_RBC_BYTE_COUNT 0x1fff /* Bytes received for current packet */ 272#define XE_RBC_COUNT_SHIFT 0x00 273#define XE_RBC_FULL_PACKET_RX 0x2000 /* These mirror bits 2:0 of ESR, if ECR:7 is set */ 274#define XE_RBC_PART_PACKET_RX 0x4000 275#define XE_RBC_REJECT_PACKET 0x8000 276 277 278/* 279 * Page 1 registers 280 */ 281#define XE_IMR0 0x0c /* Interrupt mask register 0 */ 282#define XE_IMR1 0x0d /* Interrupt mask register 1 (CE2 only) */ 283#define XE_ECR 0x0e /* Ethernet configuration register */ 284 285/* XE_IMR0 bits */ 286#define XE_IMR0_TX_OVERFLOW 0x01 /* Masks for bits in ISR */ 287#define XE_IMR0_TX_PACKET 0x02 288#define XE_IMR0_MAC_INTR 0x04 289#define XE_IMR0_RX_EARLY 0x10 290#define XE_IMR0_RX_PACKET 0x20 291#define XE_IMR0_RX_REJECT 0x40 292#define XE_IMR0_FORCE_INTR 0x80 293 294/* XE_ECR bits */ 295#define XE_ECR_EARLY_TX 0x01 /* Enable early transmit mode */ 296#define XE_ECR_EARLY_RX 0x02 /* Enable early receive mode */ 297#define XE_ECR_FULL_DUPLEX 0x04 /* Enable full-duplex (disable collision detection) */ 298#define XE_ECR_LONG_TPCABLE 0x08 /* CE2 only */ 299#define XE_ECR_NO_POL_COL 0x10 /* CE2 only */ 300#define XE_ECR_NO_LINK_PULSE 0x20 /* Don't check/send link pulses (not 10BT compliant) */ 301#define XE_ECR_NO_AUTO_TX 0x40 /* CE2 only */ 302#define XE_ECR_SOFT_COMPAT 0x80 /* Map ESR bits 2:0 to RBC bits 15:13 */ 303 304 305/* 306 * Page 2 registers 307 */ 308#define XE_RBS 0x08 /* Receive buffer start (16 bits) */ 309#define XE_LED 0x0a /* LED control register */ 310#define XE_LED3 0x0b /* LED3 control register */ 311#define XE_MSR 0x0c /* Misc. setup register (Mohawk specific register?) */ 312#define XE_GPR2 0x0d /* General purpose register 2 */ 313 314/* 315 * LED function selection: 316 * 000 - Disabled 317 * 001 - Collision activity 318 * 010 - !Collision activity 319 * 011 - 10Mbit link detected 320 * 100 - 100Mbit link detected 321 * 101 - 10/100Mbit link detected 322 * 110 - Automatic assertion 323 * 111 - Transmit activity 324 */ 325 326/* XE_LED bits */ 327#define XE_LED_LED0_MASK 0x07 /* LED0 function selection */ 328#define XE_LED_LED0_SHIFT 0x00 329#define XE_LED_LED1_MASK 0x38 /* LED1 function selection */ 330#define XE_LED_LED1_SHIFT 0x03 331#define XE_LED_LED0_RX 0x40 /* Add receive activity to LED0 */ 332#define XE_LED_LED1_RX 0x80 /* Add receive activity to LED1 */ 333 334/* XE_LED3 bits */ 335#define XE_LED3_MASK 0x07 /* LED3 function selection */ 336#define XE_LED3_SHIFT 0x00 337#define XE_LED3_RX 0x40 /* Add receive activity to LED3 */ 338 339/* XE_MSR bits */ 340#define XE_MSR_128K_SRAM 0x01 /* Select 128K SRAM */ 341#define XE_MSR_RBS_BIT16 0x02 /* Bit 16 of RBS (only useful with big SRAM) */ 342#define XE_MSR_MII_SELECT 0x08 /* Select MII instead of SSI interface */ 343#define XE_MSR_HASH_TABLE 0x20 /* Enable hash table filtering */ 344 345/* XE_GPR2 bits */ 346#define XE_GPR2_GP3_OUT 0x01 /* Value written to GP3 line */ 347#define XE_GPR2_GP4_OUT 0x02 /* Value written to GP4 line */ 348#define XE_GPR2_GP3_SELECT 0x04 /* 1 = GP3 is output, 0 = GP3 is input */ 349#define XE_GPR2_GP4_SELECT 0x08 /* 1 = GP4 is output, 0 = GP3 is input */ 350#define XE_GPR2_GP3_IN 0x10 /* Value read from GP3 line */ 351#define XE_GPR2_GP4_IN 0x20 /* Value read from GP4 line */ 352 353 354/* 355 * Page 3 registers 356 */ 357#define XE_TPT 0x0a /* Transmit packet threshold (13 bits) */ 358 359 360/* 361 * Page 4 registers 362 */ 363#define XE_GPR0 0x08 /* General purpose register 0 */ 364#define XE_GPR1 0x09 /* General purpose register 1 */ 365#define XE_BOV 0x0a /* Bonding version register (read) */ 366#define XE_EES 0x0b /* EEPROM control register */ 367#define XE_LMA 0x0c /* Local memory address (CE2 only) */ 368#define XE_LMD 0x0e /* Local memory data (CE2 only) */ 369 370/* XE_GPR0 bits */ 371#define XE_GPR0_GP1_OUT 0x01 /* Value written to GP1 line */ 372#define XE_GPR0_GP2_OUT 0x02 /* Value wirtten to GP2 line */ 373#define XE_GPR0_GP1_SELECT 0x04 /* 1 = GP1 is output, 0 = GP1 is input */ 374#define XE_GPR0_GP2_SELECT 0x08 /* 1 = GP2 is output, 0 = GP2 is input */ 375#define XE_GPR0_GP1_IN 0x10 /* Value read from GP1 line */ 376#define XE_GPR0_GP2_IN 0x20 /* Value read from GP2 line */ 377 378/* XE_GPR1 bits */ 379#define XE_GPR1_POWER_DOWN 0x01 /* Power down analog section (down to 20mA load) */ 380 381/* XE_BOV values */ 382#define XE_BOV_DINGO 0x55 /* Dingo in Dingo mode */ 383#define XE_BOV_MOHAWK 0x41 /* Original Mohawk */ 384#define XE_BOV_MOHAWK_REV1 0x45 /* Rev. 1 Mohawk, or Dingo in Mohawk mode */ 385#define XE_BOV_CEM28 0x11 /* CEM28 */ 386 387/* XE_EES bits */ 388#define XE_EES_SCL_OUTPUT 0x01 /* Value written to SCL line, when MANUAL_ROM set */ 389#define XE_EES_SDA_OUTPUT 0x02 /* Value written to SDA line, when MANUAL_ROM set */ 390#define XE_EES_SDA_INPUT 0x04 /* Value read from SDA line */ 391#define XE_EES_SDA_TRISTATE 0x08 /* 1 = SDA is output, 0 = SDA is input */ 392#define XE_EES_MANUAL_ROM 0x20 /* Enable manual contro of serial EEPROM */ 393 394 395/* 396 * Page 5 registers (all read only) 397 */ 398#define XE_CRHA 0x08 /* Current Rx host address (16 bits) */ 399#define XE_RHSA 0x0a /* Rx host start address (16 bits) */ 400#define XE_RNSA 0x0c /* Rx network start address (16 bits) */ 401#define XE_CRNA 0x0e /* Current Rx network address (16 bits) */ 402 403 404/* 405 * Page 6 registers (all read only) 406 */ 407#define XE_CTHA 0x08 /* Current Tx host address (16 bits) */ 408#define XE_THSA 0x0a /* Tx host start address (16 bits) */ 409#define XE_TNSA 0x0c /* Tx network statr address (16 bits) */ 410#define XE_CTNA 0x0e /* Current Tx network address (16 bits) */ 411 412 413/* 414 * Page 8 registers (all read only) 415 */ 416#define XE_THBC 0x08 /* Tx host byte count (16 bits) */ 417#define XE_THPS 0x0a /* Tx host packet size (16 bits) */ 418#define XE_TNBC 0x0c /* Tx network byte count (16 bits) */ 419#define XE_TNPS 0x0e /* Tx network packet size (16 bits) */ 420 421 422/* 423 * Page 0x10 registers (all read only) 424 */ 425#define XE_DINGOID 0x08 /* Dingo ID register (16 bits) (Dingo only) */ 426#define XE_RevID 0x0a /* Dingo revision ID (16 bits) (Dingo only) */ 427#define XE_VendorID 0x0c /* Dingo vendor ID (16 bits) (Dingo only) */ 428 429/* Values for the above registers */ 430#define XE_DINGOID_DINGO3 0x444b /* In both Dingo and Mohawk modes */ 431#define XE_RevID_DINGO3 0x0001 432#define XE_VendorID_DINGO3 0x0041 433 434 435/* 436 * Page 0x40 registers 437 */ 438#define XE_CMD0 0x08 /* MAC Command register (write) */ 439#define XE_RST0 0x09 /* Receive status register */ 440#define XE_TXST0 0x0b /* Transmit status register 0 */ 441#define XE_TXST1 0x0c /* Transmit status register 1 */ 442#define XE_RX0Msk 0x0d /* Receive status mask register */ 443#define XE_TX0Msk 0x0e /* Transmit status 0 mask register */ 444#define XE_TX1Msk 0x0f /* Transmit status 1 mask register */ 445 446/* CMD0 bits */ 447#define XE_CMD0_TX 0x01 /* CE2 only */ 448#define XE_CMD0_RX_ENABLE 0x04 /* Enable receiver */ 449#define XE_CMD0_RX_DISABLE 0x08 /* Disable receiver */ 450#define XE_CMD0_ABORT 0x10 /* CE2 only */ 451#define XE_CMD0_ONLINE 0x20 /* Take MAC online */ 452#define XE_CMD0_ACK_INTR 0x40 /* CE2 only */ 453#define XE_CMD0_OFFLINE 0x80 /* Take MAC offline */ 454 455/* RST0 bits */ 456#define XE_RST0_LONG_PACKET 0x02 /* Packet received with >1518 and <8184 bytes */ 457#define XE_RST0_CRC_ERROR 0x08 /* Packet received with incorrect CRC */ 458#define XE_RST0_RX_OVERRUN 0x10 /* Receiver overrun, byte(s) dropped */ 459#define XE_RST0_RX_ENABLE 0x20 /* Receiver enabled */ 460#define XE_RST0_RX_ABORT 0x40 /* Receive aborted: CRC, FIFO overrun or addr mismatch */ 461#define XE_RST0_RX_OK 0x80 /* Complete packet received OK */ 462 463/* TXST0 bits */ 464#define XE_TXST0_NO_CARRIER 0x01 /* Lost carrier. Only valid in 10Mbit half-duplex */ 465#define XE_TXST0_16_COLLISIONS 0x02 /* Packet aborted after 16 collisions */ 466#define XE_TXST0_TX_UNDERRUN 0x08 /* MAC ran out of data to send */ 467#define XE_TXST0_LATE_COLLISION 0x10 /* Collision later than 512 bits */ 468#define XE_TXST0_SQE_FAIL 0x20 /* SQE test failed. */ 469#define XE_TXST0_TX_ABORT 0x40 /* Transmit aborted: collisions, underrun or overrun */ 470#define XE_TXST0_TX_OK 0x80 /* Complete packet sent OK */ 471 472/* TXST1 bits */ 473#define XE_TXST1_RETRY_COUNT 0x0f /* Collision counter for current packet */ 474#define XE_TXST1_LINK_STATUS 0x10 /* Valid link status */ 475 476/* RX0Msk bits */ 477#define XE_RX0M_LONG_PACKET 0x02 /* Masks for bits in RXST0 */ 478#define XE_RX0M_ALIGN_ERROR 0x04 /* Alignment error (CE2 only) */ 479#define XE_RX0M_CRC_ERROR 0x08 480#define XE_RX0M_RX_OVERRUN 0x10 481#define XE_RX0M_RX_ABORT 0x40 482#define XE_RX0M_RX_OK 0x80 483 484/* TX0Msk bits */ 485#define XE_TX0M_NO_CARRIER 0x01 /* Masks for bits in TXST0 */ 486#define XE_TX0M_16_COLLISIONS 0x02 487#define XE_TX0M_TX_UNDERRUN 0x08 488#define XE_TX0M_LATE_COLLISION 0x10 489#define XE_TX0M_SQE_FAIL 0x20 490#define XE_TX0M_TX_ABORT 0x40 491#define XE_TX0M_TX_OK 0x80 492 493/* TX1Msk bits */ 494#define XE_TX1M_PKTDEF 0x20 495 496 497/* 498 * Page 0x42 registers 499 */ 500#define XE_SWC0 0x08 /* Software configuration 0 */ 501#define XE_SWC1 0x09 /* Software configuration 1 */ 502#define XE_BOC 0x0a /* Back-off configuration */ 503#define XE_TCD 0x0b /* Transmit collision deferral */ 504 505/* SWC0 bits */ 506#define XE_SWC0_LOOPBACK_ENABLE 0x01 /* Enable loopback operation */ 507#define XE_SWC0_LOOPBACK_SOURCE 0x02 /* 1 = Transceiver, 0 = MAC */ 508#define XE_SWC0_ACCEPT_ERROR 0x04 /* Accept otherwise OK packets with CRC errors */ 509#define XE_SWC0_ACCEPT_SHORT 0x08 /* Accept otherwise OK packets that are too short */ 510#define XE_SWC0_NO_CRC_INSERT 0x40 /* Don't add CRC to outgoing packets */ 511 512/* SWC1 bits */ 513#define XE_SWC1_IA_ENABLE 0x01 /* Enable individual address filters */ 514#define XE_SWC1_ALLMULTI 0x02 /* Accept all multicast packets */ 515#define XE_SWC1_PROMISCUOUS 0x04 /* Accept all non-multicast packets */ 516#define XE_SWC1_BCAST_DISABLE 0x08 /* Reject broadcast packets */ 517#define XE_SWC1_MEDIA_SELECT 0x40 /* AUI media select (Mohawk only) */ 518#define XE_SWC1_AUTO_MEDIA 0x80 /* Auto media select (Mohawk only) */ 519 520 521/* 522 * Page 0x44 registers (CE2 only) 523 */ 524#define XE_TDR0 0x08 /* Time domain reflectometry register 0 */ 525#define XE_TDR1 0x09 /* Time domain reflectometry register 1 */ 526#define XE_RXC0 0x0a /* Receive byte count low */ 527#define XE_RXC1 0x0b /* Receive byte count high */ 528 529 530/* 531 * Page 0x45 registers (CE2 only) 532 */ 533#define XE_REV 0x0f /* Revision (read) */ 534 535 536/* 537 * Page 0x50-0x57: Individual address 0-9 538 * 539 * Used to filter incoming packets by matching against individual node 540 * addresses. If IA matching is enabled (SWC1, bit0) any incoming packet with 541 * a destination matching one of these 10 addresses will be received. IA0 is 542 * always enabled and usually matches the card's unique address. 543 * 544 * Addresses are stored LSB first, ie. IA00 (reg. 8 on page 0x50) contains the 545 * LSB of IA0, and so on. The data is stored contiguously, in that addresses 546 * can be broken across page boundaries. That is: 547 * 548 * Reg: 50/8 50/9 50/a 50/b 50/c 50/d 50/e 50/f 51/8 51/9 ... 57/a 57/b 549 * IA00 IA01 IA02 IA03 IA04 IA05 IA10 IA11 IA12 IA13 ... IA94 IA95 550 */ 551 552/* 553 * Page 0x58: Multicast hash table filter 554 * 555 * In case the 10 individual addresses aren't enough, we also have a multicast 556 * hash filter, enabled through MSR:5. The most significant six bits of the 557 * CRC on each incoming packet are reversed and used as an index into the 64 558 * bits of the hash table. If the appropriate bit is set the packet it 559 * received, although higher layers may still need to filter it out. The CRC 560 * calculation is as follows: 561 * 562 * crc = 0xffffffff; 563 * poly = 0x04c11db6; 564 * for (i = 0; i < 6; i++) { 565 * current = mcast_addr[i]; 566 * for (k = 1; k <= 8; k++) { 567 * if (crc & 0x80000000); 568 * crc31 = 0x01; 569 * else 570 * crc31 = 0; 571 * bit = crc31 ^ (current & 0x01); 572 * crc <<= 1; 573 * current >>= 1; 574 * if (bit) 575 * crc = (crc ^ poly)|1 576 * } 577 * } 578 */ 579 580 581 582/**************** 583 * MII registers 584 ****************/ 585 586/* 587 * Basic MII-compliant PHY register definitions. According to the Dingo spec, 588 * PHYs from (at least) MicroLinear, National Semiconductor, ICS, TDK and 589 * Quality Semiconductor have been used. These apparently all come up with 590 * PHY ID 0x00 unless the "interceptor module" on the Dingo 3 is in use. With 591 * the interceptor enabled, the PHY is faked up to look like an ICS unit with 592 * ID 0x16. The interceptor can be enabled/disabled in software. 593 * 594 * The ML6692 (and maybe others) doesn't have a 10Mbps mode -- this is handled 595 * by an internal 10Mbps transceiver that we know nothing about... some cards 596 * seem to work with the MII in 10Mbps mode, so I guess some PHYs must support 597 * it. The question is, how can you figure out which one you have? Just to 598 * add to the fun there are also 10Mbps _only_ Mohawk/Dingo cards. Aaargh! 599 */ 600 601/* 602 * Masks for the MII-related bits in GPR2 603 */ 604#define XE_MII_CLK XE_GPR2_GP3_OUT 605#define XE_MII_DIR XE_GPR2_GP4_SELECT 606#define XE_MII_WRD XE_GPR2_GP4_OUT 607#define XE_MII_RDD XE_GPR2_GP4_IN 608 609/* 610 * MII PHY ID register values 611 */ 612#define PHY_ID_ML6692 0x0000 /* MicroLinear ML6692? Or unknown */ 613#define PHY_ID_ICS1890 0x0015 /* ICS1890 */ 614#define PHY_ID_QS6612 0x0181 /* Quality QS6612 */ 615#define PHY_ID_DP83840 0x2000 /* National DP83840 */ 616 617/* 618 * MII command (etc) bit strings. 619 */ 620#define XE_MII_STARTDELIM 0x01 621#define XE_MII_READOP 0x02 622#define XE_MII_WRITEOP 0x01 623#define XE_MII_TURNAROUND 0x02 624 625/* 626 * PHY registers. 627 */ 628#define PHY_BMCR 0x00 /* Basic Mode Control Register */ 629#define PHY_BMSR 0x01 /* Basic Mode Status Register */ 630#define PHY_ID1 0x02 /* PHY ID 1 */ 631#define PHY_ID2 0x03 /* PHY ID 2 */ 632#define PHY_ANAR 0x04 /* Auto-Negotiation Advertisment Register */ 633#define PHY_LPAR 0x05 /* Auto-Negotiation Link Partner Ability Register */ 634#define PHY_ANER 0x06 /* Auto-Negotiation Expansion Register */ 635 636/* BMCR bits */ 637#define PHY_BMCR_RESET 0x8000 /* Soft reset PHY. Self-clearing */ 638#define PHY_BMCR_LOOPBK 0x4000 /* Enable loopback */ 639#define PHY_BMCR_SPEEDSEL 0x2000 /* 1=100Mbps, 0=10Mbps */ 640#define PHY_BMCR_AUTONEGENBL 0x1000 /* Auto-negotiation enabled */ 641#define PHY_BMCR_ISOLATE 0x0400 /* Isolate ML6692 from MII */ 642#define PHY_BMCR_AUTONEGRSTR 0x0200 /* Restart auto-negotiation. Self-clearing */ 643#define PHY_BMCR_DUPLEX 0x0100 /* Full duplex operation */ 644#define PHY_BMCR_COLLTEST 0x0080 /* Enable collision test */ 645 646/* BMSR bits */ 647#define PHY_BMSR_100BT4 0x8000 /* 100Base-T4 capable */ 648#define PHY_BMSR_100BTXFULL 0x4000 /* 100Base-TX full duplex capable */ 649#define PHY_BMSR_100BTXHALF 0x2000 /* 100Base-TX half duplex capable */ 650#define PHY_BMSR_10BTFULL 0x1000 /* 10Base-T full duplex capable */ 651#define PHY_BMSR_10BTHALF 0x0800 /* 10Base-T half duplex capable */ 652#define PHY_BMSR_AUTONEGCOMP 0x0020 /* Auto-negotiation complete */ 653#define PHY_BMSR_CANAUTONEG 0x0008 /* Auto-negotiation supported */ 654#define PHY_BMSR_LINKSTAT 0x0004 /* Link is up */ 655#define PHY_BMSR_EXTENDED 0x0001 /* Extended register capabilities */ 656 657/* ANAR bits */ 658#define PHY_ANAR_NEXTPAGE 0x8000 /* Additional link code word pages */ 659#define PHY_ANAR_TLRFLT 0x2000 /* Remote wire fault detected */ 660#define PHY_ANAR_100BT4 0x0200 /* 100Base-T4 capable */ 661#define PHY_ANAR_100BTXFULL 0x0100 /* 100Base-TX full duplex capable */ 662#define PHY_ANAR_100BTXHALF 0x0080 /* 100Base-TX half duplex capable */ 663#define PHY_ANAR_10BTFULL 0x0040 /* 10Base-T full duplex capable */ 664#define PHY_ANAR_10BTHALF 0x0020 /* 10Base-T half duplex capable */ 665#define PHY_ANAR_PROTO4 0x0010 /* Protocol selection (00001 = 802.3) */ 666#define PHY_ANAR_PROTO3 0x0008 667#define PHY_ANAR_PROTO2 0x0004 668#define PHY_ANAR_PROTO1 0x0002 669#define PHY_ANAR_PROTO0 0x0001 670#define PHY_ANAR_8023 PHY_ANAR_PROTO0 671#define PHY_ANAR_DINGO PHY_ANAR_100BT+PHY_ANAR_10BT_FD+PHY_ANAR_10BT+PHY_ANAR_8023 672#define PHY_ANAR_MOHAWK PHY_ANAR_100BT+PHY_ANAR_10BT_FD+PHY_ANAR_10BT+PHY_ANAR_8023 673 674/* LPAR bits */ 675#define PHY_LPAR_NEXTPAGE 0x8000 /* Additional link code word pages */ 676#define PHY_LPAR_LPACK 0x4000 /* Link partner acknowledged receipt */ 677#define PHY_LPAR_TLRFLT 0x2000 /* Remote wire fault detected */ 678#define PHY_LPAR_100BT4 0x0200 /* 100Base-T4 capable */ 679#define PHY_LPAR_100BTXFULL 0x0100 /* 100Base-TX full duplex capable */ 680#define PHY_LPAR_100BTXHALF 0x0080 /* 100Base-TX half duplex capable */ 681#define PHY_LPAR_10BTFULL 0x0040 /* 10Base-T full duplex capable */ 682#define PHY_LPAR_10BTHALF 0x0020 /* 10Base-T half duplex capable */ 683#define PHY_LPAR_PROTO4 0x0010 /* Protocol selection (00001 = 802.3) */ 684#define PHY_LPAR_PROTO3 0x0008 685#define PHY_LPAR_PROTO2 0x0004 686#define PHY_LPAR_PROTO1 0x0002 687#define PHY_LPAR_PROTO0 0x0001 688 689/* ANER bits */ 690#define PHY_ANER_MLFAULT 0x0010 /* More than one link is up! */ 691#define PHY_ANER_LPNPABLE 0x0008 /* Link partner supports next page */ 692#define PHY_ANER_NPABLE 0x0004 /* Local port supports next page */ 693#define PHY_ANER_PAGERX 0x0002 /* Page received */ 694#define PHY_ANER_LPAUTONEG 0x0001 /* Link partner can auto-negotiate */ 695 696 697#endif /* NXE > 0 */ 698