ispvar.h revision 238869
1/* $FreeBSD: head/sys/dev/isp/ispvar.h 238869 2012-07-28 20:06:29Z mjacob $ */ 2/*- 3 * Copyright (c) 1997-2009 by Matthew Jacob 4 * All rights reserved. 5 * 6 * Redistribution and use in source and binary forms, with or without 7 * modification, are permitted provided that the following conditions 8 * are met: 9 * 10 * 1. Redistributions of source code must retain the above copyright 11 * notice, this list of conditions and the following disclaimer. 12 * 2. Redistributions in binary form must reproduce the above copyright 13 * notice, this list of conditions and the following disclaimer in the 14 * documentation and/or other materials provided with the distribution. 15 * 16 * THIS SOFTWARE IS PROVIDED BY AUTHOR AND CONTRIBUTORS ``AS IS'' AND 17 * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE 18 * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE 19 * ARE DISCLAIMED. IN NO EVENT SHALL AUTHOR OR CONTRIBUTORS BE LIABLE 20 * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL 21 * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS 22 * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) 23 * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT 24 * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY 25 * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF 26 * SUCH DAMAGE. 27 * 28 */ 29/* 30 * Soft Definitions for for Qlogic ISP SCSI adapters. 31 */ 32 33#ifndef _ISPVAR_H 34#define _ISPVAR_H 35 36#if defined(__NetBSD__) || defined(__OpenBSD__) 37#include <dev/ic/isp_stds.h> 38#include <dev/ic/ispmbox.h> 39#endif 40#ifdef __FreeBSD__ 41#include <dev/isp/isp_stds.h> 42#include <dev/isp/ispmbox.h> 43#endif 44#ifdef __linux__ 45#include "isp_stds.h" 46#include "ispmbox.h" 47#endif 48#ifdef __svr4__ 49#include "isp_stds.h" 50#include "ispmbox.h" 51#endif 52 53#define ISP_CORE_VERSION_MAJOR 7 54#define ISP_CORE_VERSION_MINOR 0 55 56/* 57 * Vector for bus specific code to provide specific services. 58 */ 59typedef struct ispsoftc ispsoftc_t; 60struct ispmdvec { 61 int (*dv_rd_isr) (ispsoftc_t *, uint32_t *, uint16_t *, uint16_t *); 62 uint32_t (*dv_rd_reg) (ispsoftc_t *, int); 63 void (*dv_wr_reg) (ispsoftc_t *, int, uint32_t); 64 int (*dv_mbxdma) (ispsoftc_t *); 65 int (*dv_dmaset) (ispsoftc_t *, XS_T *, void *); 66 void (*dv_dmaclr) (ispsoftc_t *, XS_T *, uint32_t); 67 void (*dv_reset0) (ispsoftc_t *); 68 void (*dv_reset1) (ispsoftc_t *); 69 void (*dv_dregs) (ispsoftc_t *, const char *); 70 const void * dv_ispfw; /* ptr to f/w */ 71 uint16_t dv_conf1; 72 uint16_t dv_clock; /* clock frequency */ 73}; 74 75/* 76 * Overall parameters 77 */ 78#define MAX_TARGETS 16 79#ifndef MAX_FC_TARG 80#define MAX_FC_TARG 256 81#endif 82#define ISP_MAX_TARGETS(isp) (IS_FC(isp)? MAX_FC_TARG : MAX_TARGETS) 83#define ISP_MAX_LUNS(isp) (isp)->isp_maxluns 84 85/* 86 * Macros to access ISP registers through bus specific layers- 87 * mostly wrappers to vector through the mdvec structure. 88 */ 89#define ISP_READ_ISR(isp, isrp, semap, mbox0p) \ 90 (*(isp)->isp_mdvec->dv_rd_isr)(isp, isrp, semap, mbox0p) 91 92#define ISP_READ(isp, reg) \ 93 (*(isp)->isp_mdvec->dv_rd_reg)((isp), (reg)) 94 95#define ISP_WRITE(isp, reg, val) \ 96 (*(isp)->isp_mdvec->dv_wr_reg)((isp), (reg), (val)) 97 98#define ISP_MBOXDMASETUP(isp) \ 99 (*(isp)->isp_mdvec->dv_mbxdma)((isp)) 100 101#define ISP_DMASETUP(isp, xs, req) \ 102 (*(isp)->isp_mdvec->dv_dmaset)((isp), (xs), (req)) 103 104#define ISP_DMAFREE(isp, xs, hndl) \ 105 if ((isp)->isp_mdvec->dv_dmaclr) \ 106 (*(isp)->isp_mdvec->dv_dmaclr)((isp), (xs), (hndl)) 107 108#define ISP_RESET0(isp) \ 109 if ((isp)->isp_mdvec->dv_reset0) (*(isp)->isp_mdvec->dv_reset0)((isp)) 110#define ISP_RESET1(isp) \ 111 if ((isp)->isp_mdvec->dv_reset1) (*(isp)->isp_mdvec->dv_reset1)((isp)) 112#define ISP_DUMPREGS(isp, m) \ 113 if ((isp)->isp_mdvec->dv_dregs) (*(isp)->isp_mdvec->dv_dregs)((isp),(m)) 114 115#define ISP_SETBITS(isp, reg, val) \ 116 (*(isp)->isp_mdvec->dv_wr_reg)((isp), (reg), ISP_READ((isp), (reg)) | (val)) 117 118#define ISP_CLRBITS(isp, reg, val) \ 119 (*(isp)->isp_mdvec->dv_wr_reg)((isp), (reg), ISP_READ((isp), (reg)) & ~(val)) 120 121/* 122 * The MEMORYBARRIER macro is defined per platform (to provide synchronization 123 * on Request and Response Queues, Scratch DMA areas, and Registers) 124 * 125 * Defined Memory Barrier Synchronization Types 126 */ 127#define SYNC_REQUEST 0 /* request queue synchronization */ 128#define SYNC_RESULT 1 /* result queue synchronization */ 129#define SYNC_SFORDEV 2 /* scratch, sync for ISP */ 130#define SYNC_SFORCPU 3 /* scratch, sync for CPU */ 131#define SYNC_REG 4 /* for registers */ 132#define SYNC_ATIOQ 5 /* atio result queue (24xx) */ 133 134/* 135 * Request/Response Queue defines and macros. 136 * The maximum is defined per platform (and can be based on board type). 137 */ 138/* This is the size of a queue entry (request and response) */ 139#define QENTRY_LEN 64 140/* Both request and result queue length must be a power of two */ 141#define RQUEST_QUEUE_LEN(x) MAXISPREQUEST(x) 142#ifdef ISP_TARGET_MODE 143#define RESULT_QUEUE_LEN(x) MAXISPREQUEST(x) 144#else 145#define RESULT_QUEUE_LEN(x) \ 146 (((MAXISPREQUEST(x) >> 2) < 64)? 64 : MAXISPREQUEST(x) >> 2) 147#endif 148#define ISP_QUEUE_ENTRY(q, idx) (((uint8_t *)q) + ((idx) * QENTRY_LEN)) 149#define ISP_QUEUE_SIZE(n) ((n) * QENTRY_LEN) 150#define ISP_NXT_QENTRY(idx, qlen) (((idx) + 1) & ((qlen)-1)) 151#define ISP_QFREE(in, out, qlen) \ 152 ((in == out)? (qlen - 1) : ((in > out)? \ 153 ((qlen - 1) - (in - out)) : (out - in - 1))) 154#define ISP_QAVAIL(isp) \ 155 ISP_QFREE(isp->isp_reqidx, isp->isp_reqodx, RQUEST_QUEUE_LEN(isp)) 156 157#define ISP_ADD_REQUEST(isp, nxti) \ 158 MEMORYBARRIER(isp, SYNC_REQUEST, isp->isp_reqidx, QENTRY_LEN, -1); \ 159 ISP_WRITE(isp, isp->isp_rqstinrp, nxti); \ 160 isp->isp_reqidx = nxti 161 162#define ISP_SYNC_REQUEST(isp) \ 163 MEMORYBARRIER(isp, SYNC_REQUEST, isp->isp_reqidx, QENTRY_LEN, -1); \ 164 isp->isp_reqidx = ISP_NXT_QENTRY(isp->isp_reqidx, RQUEST_QUEUE_LEN(isp)); \ 165 ISP_WRITE(isp, isp->isp_rqstinrp, isp->isp_reqidx) 166 167/* 168 * SCSI Specific Host Adapter Parameters- per bus, per target 169 */ 170typedef struct { 171 uint32_t : 8, 172 update : 1, 173 sendmarker : 1, 174 role : 2, 175 isp_req_ack_active_neg : 1, 176 isp_data_line_active_neg: 1, 177 isp_cmd_dma_burst_enable: 1, 178 isp_data_dma_burst_enabl: 1, 179 isp_fifo_threshold : 3, 180 isp_ptisp : 1, 181 isp_ultramode : 1, 182 isp_diffmode : 1, 183 isp_lvdmode : 1, 184 isp_fast_mttr : 1, /* fast sram */ 185 isp_initiator_id : 4, 186 isp_async_data_setup : 4; 187 uint16_t isp_selection_timeout; 188 uint16_t isp_max_queue_depth; 189 uint8_t isp_tag_aging; 190 uint8_t isp_bus_reset_delay; 191 uint8_t isp_retry_count; 192 uint8_t isp_retry_delay; 193 struct { 194 uint32_t 195 exc_throttle : 8, 196 : 1, 197 dev_enable : 1, /* ignored */ 198 dev_update : 1, 199 dev_refresh : 1, 200 actv_offset : 4, 201 goal_offset : 4, 202 nvrm_offset : 4; 203 uint8_t actv_period; /* current sync period */ 204 uint8_t goal_period; /* goal sync period */ 205 uint8_t nvrm_period; /* nvram sync period */ 206 uint16_t actv_flags; /* current device flags */ 207 uint16_t goal_flags; /* goal device flags */ 208 uint16_t nvrm_flags; /* nvram device flags */ 209 } isp_devparam[MAX_TARGETS]; 210} sdparam; 211 212/* 213 * Device Flags 214 */ 215#define DPARM_DISC 0x8000 216#define DPARM_PARITY 0x4000 217#define DPARM_WIDE 0x2000 218#define DPARM_SYNC 0x1000 219#define DPARM_TQING 0x0800 220#define DPARM_ARQ 0x0400 221#define DPARM_QFRZ 0x0200 222#define DPARM_RENEG 0x0100 223#define DPARM_NARROW 0x0080 224#define DPARM_ASYNC 0x0040 225#define DPARM_PPR 0x0020 226#define DPARM_DEFAULT (0xFF00 & ~DPARM_QFRZ) 227#define DPARM_SAFE_DFLT (DPARM_DEFAULT & ~(DPARM_WIDE|DPARM_SYNC|DPARM_TQING)) 228 229/* technically, not really correct, as they need to be rated based upon clock */ 230#define ISP_80M_SYNCPARMS 0x0c09 231#define ISP_40M_SYNCPARMS 0x0c0a 232#define ISP_20M_SYNCPARMS 0x0c0c 233#define ISP_20M_SYNCPARMS_1040 0x080c 234#define ISP_10M_SYNCPARMS 0x0c19 235#define ISP_08M_SYNCPARMS 0x0c25 236#define ISP_05M_SYNCPARMS 0x0c32 237#define ISP_04M_SYNCPARMS 0x0c41 238 239/* 240 * Fibre Channel Specifics 241 */ 242/* These are for non-2K Login Firmware cards */ 243#define FL_ID 0x7e /* FL_Port Special ID */ 244#define SNS_ID 0x80 /* SNS Server Special ID */ 245#define NPH_MAX 0xfe 246 247/* Use this handle for the base for multi-id firmware SNS logins */ 248#define NPH_SNS_HDLBASE 0x400 249 250/* These are for 2K Login Firmware cards */ 251#define NPH_RESERVED 0x7F0 /* begin of reserved N-port handles */ 252#define NPH_MGT_ID 0x7FA /* Management Server Special ID */ 253#define NPH_SNS_ID 0x7FC /* SNS Server Special ID */ 254#define NPH_FABRIC_CTLR 0x7FD /* Fabric Controller (0xFFFFFD) */ 255#define NPH_FL_ID 0x7FE /* F Port Special ID (0xFFFFFE) */ 256#define NPH_IP_BCST 0x7ff /* IP Broadcast Special ID (0xFFFFFF) */ 257#define NPH_MAX_2K 0x800 258 259/* 260 * "Unassigned" handle to be used internally 261 */ 262#define NIL_HANDLE 0xffff 263 264/* 265 * Limit for devices on an arbitrated loop. 266 */ 267#define LOCAL_LOOP_LIM 126 268 269/* 270 * Limit for (2K login) N-port handle amounts 271 */ 272#define MAX_NPORT_HANDLE 2048 273 274/* 275 * Special Constants 276 */ 277#define INI_NONE ((uint64_t) 0) 278#define ISP_NOCHAN 0xff 279 280/* 281 * Special Port IDs 282 */ 283#define MANAGEMENT_PORT_ID 0xFFFFFA 284#define SNS_PORT_ID 0xFFFFFC 285#define FABRIC_PORT_ID 0xFFFFFE 286#define PORT_ANY 0xFFFFFF 287#define PORT_NONE 0 288#define DOMAIN_CONTROLLER_BASE 0xFFFC00 289#define DOMAIN_CONTROLLER_END 0xFFFCFF 290 291/* 292 * Command Handles 293 * 294 * Most QLogic initiator or target have 32 bit handles associated with them. 295 * We want to have a quick way to index back and forth between a local SCSI 296 * command context and what the firmware is passing back to us. We also 297 * want to avoid working on stale information. This structure handles both 298 * at the expense of some local memory. 299 * 300 * The handle is architected thusly: 301 * 302 * 0 means "free handle" 303 * bits 0..12 index commands 304 * bits 13..15 bits index usage 305 * bits 16..31 contain a rolling sequence 306 * 307 * 308 */ 309typedef struct { 310 void * cmd; /* associated command context */ 311 uint32_t handle; /* handle associated with this command */ 312} isp_hdl_t; 313#define ISP_HANDLE_FREE 0x00000000 314#define ISP_HANDLE_CMD_MASK 0x00001fff 315#define ISP_HANDLE_USAGE_MASK 0x0000e000 316#define ISP_HANDLE_USAGE_SHIFT 13 317#define ISP_H2HT(hdl) ((hdl & ISP_HANDLE_USAGE_MASK) >> ISP_HANDLE_USAGE_SHIFT) 318# define ISP_HANDLE_NONE 0 319# define ISP_HANDLE_INITIATOR 1 320# define ISP_HANDLE_TARGET 2 321#define ISP_HANDLE_SEQ_MASK 0xffff0000 322#define ISP_HANDLE_SEQ_SHIFT 16 323#define ISP_H2SEQ(hdl) ((hdl & ISP_HANDLE_SEQ_MASK) >> ISP_HANDLE_SEQ_SHIFT) 324#define ISP_VALID_INI_HANDLE(c, hdl) \ 325 (ISP_H2HT(hdl) == ISP_HANDLE_INITIATOR && (hdl & ISP_HANDLE_CMD_MASK) < (c)->isp_maxcmds && \ 326 ISP_H2SEQ(hdl) == ISP_H2SEQ((c)->isp_xflist[hdl & ISP_HANDLE_CMD_MASK].handle)) 327#ifdef ISP_TARGET_MODE 328#define ISP_VALID_TGT_HANDLE(c, hdl) \ 329 (ISP_H2HT(hdl) == ISP_HANDLE_TARGET && (hdl & ISP_HANDLE_CMD_MASK) < (c)->isp_maxcmds && \ 330 ISP_H2SEQ(hdl) == ISP_H2SEQ((c)->isp_tgtlist[hdl & ISP_HANDLE_CMD_MASK].handle)) 331#define ISP_VALID_HANDLE(c, hdl) \ 332 (ISP_VALID_INI_HANDLE((c), hdl) || ISP_VALID_TGT_HANDLE((c), hdl)) 333#else 334#define ISP_VALID_HANDLE ISP_VALID_INI_HANDLE 335#endif 336#define ISP_BAD_HANDLE_INDEX 0xffffffff 337 338 339/* 340 * FC Port Database entry. 341 * 342 * It has a handle that the f/w uses to address commands to a device. 343 * This handle's value may be assigned by the firmware (e.g., for local loop 344 * devices) or by the driver (e.g., for fabric devices). 345 * 346 * It has a state. If the state if VALID, that means that we've logged into 347 * the device. We also *may* have a initiator map index entry. This is a value 348 * from 0..MAX_FC_TARG that is used to index into the isp_dev_map array. If 349 * the value therein is non-zero, then that value minus one is used to index 350 * into the Port Database to find the handle for forming commands. There is 351 * back-index minus one value within to Port Database entry that tells us 352 * which entry in isp_dev_map points to us (to avoid searching). 353 * 354 * Local loop devices the firmware automatically performs PLOGI on for us 355 * (which is why that handle is imposed upon us). Fabric devices we assign 356 * a handle to and perform the PLOGI on. 357 * 358 * When a PORT DATABASE CHANGED asynchronous event occurs, we mark all VALID 359 * entries as PROBATIONAL. This allows us, if policy says to, just keep track 360 * of devices whose handles change but are otherwise the same device (and 361 * thus keep 'target' constant). 362 * 363 * In any case, we search all possible local loop handles. For each one that 364 * has a port database entity returned, we search for any PROBATIONAL entry 365 * that matches it and update as appropriate. Otherwise, as a new entry, we 366 * find room for it in the Port Database. We *try* and use the handle as the 367 * index to put it into the Database, but that's just an optimization. We mark 368 * the entry VALID and make sure that the target index is updated and correct. 369 * 370 * When we get done searching the local loop, we then search similarily for 371 * a list of devices we've gotten from the fabric name controller (if we're 372 * on a fabric). VALID marking is also done similarily. 373 * 374 * When all of this is done, we can march through the database and clean up 375 * any entry that is still PROBATIONAL (these represent devices which have 376 * departed). Then we're done and can resume normal operations. 377 * 378 * Negative invariants that we try and test for are: 379 * 380 * + There can never be two non-NIL entries with the same { Port, Node } WWN 381 * duples. 382 * 383 * + There can never be two non-NIL entries with the same handle. 384 * 385 * + There can never be two non-NIL entries which have the same dev_map_idx 386 * value. 387 */ 388typedef struct { 389 /* 390 * This is the handle that the firmware needs in order for us to 391 * send commands to the device. For pre-24XX cards, this would be 392 * the 'loopid'. 393 */ 394 uint16_t handle; 395 396 /* 397 * The dev_map_idx, if nonzero, is the system virtual target ID (+1) 398 * as a cross-reference with the isp_dev_map. 399 * 400 * A device is 'autologin' if the firmware automatically logs into 401 * it (re-logins as needed). Basically, local private loop devices. 402 * 403 * PRLI word 3 parameters contains role as well as other things. 404 * 405 * The state is the current state of this entry. 406 * 407 * Portid is obvious, as are node && port WWNs. The new_role and 408 * new_portid is for when we are pending a change. 409 * 410 * The 'target_mode' tag means that this entry arrived via a 411 * target mode command and is immune from normal flushing rules. 412 * You should also never see anything with an initiator role 413 * with this set. 414 */ 415 uint16_t prli_word3; /* PRLI parameters */ 416 uint16_t new_prli_word3; /* Incoming new PRLI parameters */ 417 uint16_t dev_map_idx : 12, 418 autologin : 1, /* F/W does PLOGI/PLOGO */ 419 state : 3; 420 uint32_t : 7, 421 target_mode : 1, 422 portid : 24; 423 uint32_t 424 : 6, 425 announced : 1, 426 dirty : 1, /* commands have been run */ 427 new_portid : 24; 428 uint64_t node_wwn; 429 uint64_t port_wwn; 430 uint32_t gone_timer; 431} fcportdb_t; 432 433#define FC_PORTDB_STATE_NIL 0 434#define FC_PORTDB_STATE_PROBATIONAL 1 435#define FC_PORTDB_STATE_DEAD 2 436#define FC_PORTDB_STATE_CHANGED 3 437#define FC_PORTDB_STATE_NEW 4 438#define FC_PORTDB_STATE_PENDING_VALID 5 439#define FC_PORTDB_STATE_ZOMBIE 6 440#define FC_PORTDB_STATE_VALID 7 441 442/* 443 * FC card specific information 444 * 445 * This structure is replicated across multiple channels for multi-id 446 * capapble chipsets, with some entities different on a per-channel basis. 447 */ 448 449typedef struct { 450 uint32_t 451 fctape_enabled : 1, 452 link_active : 1, 453 sendmarker : 1, 454 role : 2, 455 isp_gbspeed : 4, 456 isp_loopstate : 4, /* Current Loop State */ 457 isp_fwstate : 4, /* ISP F/W state */ 458 isp_topo : 3, /* Connection Type */ 459 loop_seen_once : 1; 460 461 uint32_t : 8, 462 isp_portid : 24; /* S_ID */ 463 464 465 uint16_t isp_fwoptions; 466 uint16_t isp_xfwoptions; 467 uint16_t isp_zfwoptions; 468 uint16_t isp_loopid; /* hard loop id */ 469 uint16_t isp_sns_hdl; /* N-port handle for SNS */ 470 uint16_t isp_lasthdl; /* only valid for channel 0 */ 471 uint16_t isp_maxalloc; 472 uint16_t isp_fabric_params; 473 uint8_t isp_retry_delay; 474 uint8_t isp_retry_count; 475 476 /* 477 * Current active WWNN/WWPN 478 */ 479 uint64_t isp_wwnn; 480 uint64_t isp_wwpn; 481 482 /* 483 * NVRAM WWNN/WWPN 484 */ 485 uint64_t isp_wwnn_nvram; 486 uint64_t isp_wwpn_nvram; 487 488 /* 489 * Our Port Data Base 490 */ 491 fcportdb_t portdb[MAX_FC_TARG]; 492 493 /* 494 * This maps system virtual 'target' id to a portdb entry. 495 * 496 * The mapping function is to take any non-zero entry and 497 * subtract one to get the portdb index. This means that 498 * entries which are zero are unmapped (i.e., don't exist). 499 */ 500 uint16_t isp_dev_map[MAX_FC_TARG]; 501 502#ifdef ISP_TARGET_MODE 503 /* 504 * This maps N-Port Handle to portdb entry so we 505 * don't have to search for every incoming command. 506 * 507 * The mapping function is to take any non-zero entry and 508 * subtract one to get the portdb index. This means that 509 * entries which are zero are unmapped (i.e., don't exist). 510 */ 511 uint16_t isp_tgt_map[MAX_NPORT_HANDLE]; 512#endif 513 514 /* 515 * Scratch DMA mapped in area to fetch Port Database stuff, etc. 516 */ 517 void * isp_scratch; 518 XS_DMA_ADDR_T isp_scdma; 519} fcparam; 520 521#define FW_CONFIG_WAIT 0 522#define FW_WAIT_AL_PA 1 523#define FW_WAIT_LOGIN 2 524#define FW_READY 3 525#define FW_LOSS_OF_SYNC 4 526#define FW_ERROR 5 527#define FW_REINIT 6 528#define FW_NON_PART 7 529 530#define LOOP_NIL 0 531#define LOOP_LIP_RCVD 1 532#define LOOP_PDB_RCVD 2 533#define LOOP_SCANNING_LOOP 3 534#define LOOP_LSCAN_DONE 4 535#define LOOP_SCANNING_FABRIC 5 536#define LOOP_FSCAN_DONE 6 537#define LOOP_SYNCING_PDB 7 538#define LOOP_READY 8 539 540#define TOPO_NL_PORT 0 541#define TOPO_FL_PORT 1 542#define TOPO_N_PORT 2 543#define TOPO_F_PORT 3 544#define TOPO_PTP_STUB 4 545 546/* 547 * Soft Structure per host adapter 548 */ 549struct ispsoftc { 550 /* 551 * Platform (OS) specific data 552 */ 553 struct isposinfo isp_osinfo; 554 555 /* 556 * Pointer to bus specific functions and data 557 */ 558 struct ispmdvec * isp_mdvec; 559 560 /* 561 * (Mostly) nonvolatile state. Board specific parameters 562 * may contain some volatile state (e.g., current loop state). 563 */ 564 565 void * isp_param; /* type specific */ 566 uint64_t isp_fwattr; /* firmware attributes */ 567 uint16_t isp_fwrev[3]; /* Loaded F/W revision */ 568 uint16_t isp_maxcmds; /* max possible I/O cmds */ 569 uint8_t isp_type; /* HBA Chip Type */ 570 uint8_t isp_revision; /* HBA Chip H/W Revision */ 571 uint16_t isp_nchan; /* number of channels */ 572 uint32_t isp_maxluns; /* maximum luns supported */ 573 574 uint32_t isp_clock : 8, /* input clock */ 575 : 4, 576 isp_port : 1, /* 23XX/24XX only */ 577 isp_open : 1, /* opened (ioctl) */ 578 isp_bustype : 1, /* SBus or PCI */ 579 isp_loaded_fw : 1, /* loaded firmware */ 580 isp_dblev : 16; /* debug log mask */ 581 582 583 uint32_t isp_confopts; /* config options */ 584 585 uint32_t isp_rqstinrp; /* register for REQINP */ 586 uint32_t isp_rqstoutrp; /* register for REQOUTP */ 587 uint32_t isp_respinrp; /* register for RESINP */ 588 uint32_t isp_respoutrp; /* register for RESOUTP */ 589 590 /* 591 * Instrumentation 592 */ 593 uint64_t isp_intcnt; /* total int count */ 594 uint64_t isp_intbogus; /* spurious int count */ 595 uint64_t isp_intmboxc; /* mbox completions */ 596 uint64_t isp_intoasync; /* other async */ 597 uint64_t isp_rsltccmplt; /* CMDs on result q */ 598 uint64_t isp_fphccmplt; /* CMDs via fastpost */ 599 uint16_t isp_rscchiwater; 600 uint16_t isp_fpcchiwater; 601 NANOTIME_T isp_init_time; /* time were last initialized */ 602 603 /* 604 * Volatile state 605 */ 606 607 volatile uint32_t : 8, 608 : 2, 609 isp_dead : 1, 610 : 1, 611 isp_mboxbsy : 1, /* mailbox command active */ 612 isp_state : 3, 613 isp_nactive : 16; /* how many commands active */ 614 volatile mbreg_t isp_curmbx; /* currently active mailbox command */ 615 volatile uint32_t isp_reqodx; /* index of last ISP pickup */ 616 volatile uint32_t isp_reqidx; /* index of next request */ 617 volatile uint32_t isp_residx; /* index of next result */ 618 volatile uint32_t isp_resodx; /* index of next result */ 619 volatile uint32_t isp_obits; /* mailbox command output */ 620 volatile uint32_t isp_serno; /* rolling serial number */ 621 volatile uint16_t isp_mboxtmp[MAX_MAILBOX]; 622 volatile uint16_t isp_lastmbxcmd; /* last mbox command sent */ 623 volatile uint16_t isp_mbxwrk0; 624 volatile uint16_t isp_mbxwrk1; 625 volatile uint16_t isp_mbxwrk2; 626 volatile uint16_t isp_mbxwrk8; 627 volatile uint16_t isp_seqno; /* running sequence number */ 628 void * isp_mbxworkp; 629 630 /* 631 * Active commands are stored here, indexed by handle functions. 632 */ 633 isp_hdl_t *isp_xflist; 634 isp_hdl_t *isp_xffree; 635 636#ifdef ISP_TARGET_MODE 637 /* 638 * Active target commands are stored here, indexed by handle functions. 639 */ 640 isp_hdl_t *isp_tgtlist; 641 isp_hdl_t *isp_tgtfree; 642#endif 643 644 /* 645 * request/result queue pointers and DMA handles for them. 646 */ 647 void * isp_rquest; 648 void * isp_result; 649 XS_DMA_ADDR_T isp_rquest_dma; 650 XS_DMA_ADDR_T isp_result_dma; 651#ifdef ISP_TARGET_MODE 652 /* for 24XX only */ 653 void * isp_atioq; 654 XS_DMA_ADDR_T isp_atioq_dma; 655#endif 656}; 657 658#define SDPARAM(isp, chan) (&((sdparam *)(isp)->isp_param)[(chan)]) 659#define FCPARAM(isp, chan) (&((fcparam *)(isp)->isp_param)[(chan)]) 660 661#define ISP_SET_SENDMARKER(isp, chan, val) \ 662 if (IS_FC(isp)) { \ 663 FCPARAM(isp, chan)->sendmarker = val; \ 664 } else { \ 665 SDPARAM(isp, chan)->sendmarker = val; \ 666 } 667 668#define ISP_TST_SENDMARKER(isp, chan) \ 669 (IS_FC(isp)? \ 670 FCPARAM(isp, chan)->sendmarker != 0 : \ 671 SDPARAM(isp, chan)->sendmarker != 0) 672 673/* 674 * ISP Driver Run States 675 */ 676#define ISP_NILSTATE 0 677#define ISP_CRASHED 1 678#define ISP_RESETSTATE 2 679#define ISP_INITSTATE 3 680#define ISP_RUNSTATE 4 681 682/* 683 * ISP Runtime Configuration Options 684 */ 685#define ISP_CFG_FULL_DUPLEX 0x01 /* Full Duplex (Fibre Channel only) */ 686#define ISP_CFG_PORT_PREF 0x0c /* Mask for Port Prefs (all FC except 2100) */ 687#define ISP_CFG_LPORT 0x00 /* prefer {N/F}L-Port connection */ 688#define ISP_CFG_NPORT 0x04 /* prefer {N/F}-Port connection */ 689#define ISP_CFG_NPORT_ONLY 0x08 /* insist on {N/F}-Port connection */ 690#define ISP_CFG_LPORT_ONLY 0x0c /* insist on {N/F}L-Port connection */ 691#define ISP_CFG_ONEGB 0x10 /* force 1GB connection (23XX only) */ 692#define ISP_CFG_TWOGB 0x20 /* force 2GB connection (23XX only) */ 693#define ISP_CFG_NORELOAD 0x80 /* don't download f/w */ 694#define ISP_CFG_NONVRAM 0x40 /* ignore NVRAM */ 695#define ISP_CFG_NOFCTAPE 0x100 /* disable FC-Tape */ 696#define ISP_CFG_FCTAPE 0x200 /* enable FC-Tape */ 697#define ISP_CFG_OWNFSZ 0x400 /* override NVRAM frame size */ 698#define ISP_CFG_OWNLOOPID 0x800 /* override NVRAM loopid */ 699#define ISP_CFG_OWNEXCTHROTTLE 0x1000 /* override NVRAM execution throttle */ 700#define ISP_CFG_FOURGB 0x2000 /* force 4GB connection (24XX only) */ 701#define ISP_CFG_EIGHTGB 0x4000 /* force 8GB connection (25XX only) */ 702#define ISP_CFG_SIXTEENGB 0x8000 /* force 16GB connection (82XX only) */ 703 704/* 705 * For each channel, the outer layers should know what role that channel 706 * will take: ISP_ROLE_NONE, ISP_ROLE_INITIATOR, ISP_ROLE_TARGET, 707 * ISP_ROLE_BOTH. 708 * 709 * If you set ISP_ROLE_NONE, the cards will be reset, new firmware loaded, 710 * NVRAM read, and defaults set, but any further initialization (e.g. 711 * INITIALIZE CONTROL BLOCK commands for 2X00 cards) won't be done. 712 * 713 * If INITIATOR MODE isn't set, attempts to run commands will be stopped 714 * at isp_start and completed with the equivalent of SELECTION TIMEOUT. 715 * 716 * If TARGET MODE is set, it doesn't mean that the rest of target mode support 717 * needs to be enabled, or will even work. What happens with the 2X00 cards 718 * here is that if you have enabled it with TARGET MODE as part of the ICB 719 * options, but you haven't given the f/w any ram resources for ATIOs or 720 * Immediate Notifies, the f/w just handles what it can and you never see 721 * anything. Basically, it sends a single byte of data (the first byte, 722 * which you can set as part of the INITIALIZE CONTROL BLOCK command) for 723 * INQUIRY, and sends back QUEUE FULL status for any other command. 724 * 725 */ 726#define ISP_ROLE_NONE 0x0 727#define ISP_ROLE_TARGET 0x1 728#define ISP_ROLE_INITIATOR 0x2 729#define ISP_ROLE_BOTH (ISP_ROLE_TARGET|ISP_ROLE_INITIATOR) 730#define ISP_ROLE_EITHER ISP_ROLE_BOTH 731#ifndef ISP_DEFAULT_ROLES 732/* 733 * Counterintuitively, we prefer to default to role 'none' 734 * if we are enable target mode support. This gives us the 735 * maximum flexibility as to which port will do what. 736 */ 737#ifdef ISP_TARGET_MODE 738#define ISP_DEFAULT_ROLES ISP_ROLE_NONE 739#else 740#define ISP_DEFAULT_ROLES ISP_ROLE_INITIATOR 741#endif 742#endif 743 744 745/* 746 * Firmware related defines 747 */ 748#define ISP_CODE_ORG 0x1000 /* default f/w code start */ 749#define ISP_CODE_ORG_2300 0x0800 /* ..except for 2300s */ 750#define ISP_CODE_ORG_2400 0x100000 /* ..and 2400s */ 751#define ISP_FW_REV(maj, min, mic) ((maj << 24) | (min << 16) | mic) 752#define ISP_FW_MAJOR(code) ((code >> 24) & 0xff) 753#define ISP_FW_MINOR(code) ((code >> 16) & 0xff) 754#define ISP_FW_MICRO(code) ((code >> 8) & 0xff) 755#define ISP_FW_REVX(xp) ((xp[0]<<24) | (xp[1] << 16) | xp[2]) 756#define ISP_FW_MAJORX(xp) (xp[0]) 757#define ISP_FW_MINORX(xp) (xp[1]) 758#define ISP_FW_MICROX(xp) (xp[2]) 759#define ISP_FW_NEWER_THAN(i, major, minor, micro) \ 760 (ISP_FW_REVX((i)->isp_fwrev) > ISP_FW_REV(major, minor, micro)) 761#define ISP_FW_OLDER_THAN(i, major, minor, micro) \ 762 (ISP_FW_REVX((i)->isp_fwrev) < ISP_FW_REV(major, minor, micro)) 763 764/* 765 * Bus (implementation) types 766 */ 767#define ISP_BT_PCI 0 /* PCI Implementations */ 768#define ISP_BT_SBUS 1 /* SBus Implementations */ 769 770/* 771 * If we have not otherwise defined SBus support away make sure 772 * it is defined here such that the code is included as default 773 */ 774#ifndef ISP_SBUS_SUPPORTED 775#define ISP_SBUS_SUPPORTED 1 776#endif 777 778/* 779 * Chip Types 780 */ 781#define ISP_HA_SCSI 0xf 782#define ISP_HA_SCSI_UNKNOWN 0x1 783#define ISP_HA_SCSI_1020 0x2 784#define ISP_HA_SCSI_1020A 0x3 785#define ISP_HA_SCSI_1040 0x4 786#define ISP_HA_SCSI_1040A 0x5 787#define ISP_HA_SCSI_1040B 0x6 788#define ISP_HA_SCSI_1040C 0x7 789#define ISP_HA_SCSI_1240 0x8 790#define ISP_HA_SCSI_1080 0x9 791#define ISP_HA_SCSI_1280 0xa 792#define ISP_HA_SCSI_10160 0xb 793#define ISP_HA_SCSI_12160 0xc 794#define ISP_HA_FC 0xf0 795#define ISP_HA_FC_2100 0x10 796#define ISP_HA_FC_2200 0x20 797#define ISP_HA_FC_2300 0x30 798#define ISP_HA_FC_2312 0x40 799#define ISP_HA_FC_2322 0x50 800#define ISP_HA_FC_2400 0x60 801#define ISP_HA_FC_2500 0x70 802 803#define IS_SCSI(isp) (isp->isp_type & ISP_HA_SCSI) 804#define IS_1020(isp) (isp->isp_type < ISP_HA_SCSI_1240) 805#define IS_1240(isp) (isp->isp_type == ISP_HA_SCSI_1240) 806#define IS_1080(isp) (isp->isp_type == ISP_HA_SCSI_1080) 807#define IS_1280(isp) (isp->isp_type == ISP_HA_SCSI_1280) 808#define IS_10160(isp) (isp->isp_type == ISP_HA_SCSI_10160) 809#define IS_12160(isp) (isp->isp_type == ISP_HA_SCSI_12160) 810 811#define IS_12X0(isp) (IS_1240(isp) || IS_1280(isp)) 812#define IS_1X160(isp) (IS_10160(isp) || IS_12160(isp)) 813#define IS_DUALBUS(isp) (IS_12X0(isp) || IS_12160(isp)) 814#define IS_ULTRA2(isp) (IS_1080(isp) || IS_1280(isp) || IS_1X160(isp)) 815#define IS_ULTRA3(isp) (IS_1X160(isp)) 816 817#define IS_FC(isp) ((isp)->isp_type & ISP_HA_FC) 818#define IS_2100(isp) ((isp)->isp_type == ISP_HA_FC_2100) 819#define IS_2200(isp) ((isp)->isp_type == ISP_HA_FC_2200) 820#define IS_23XX(isp) ((isp)->isp_type >= ISP_HA_FC_2300 && \ 821 (isp)->isp_type < ISP_HA_FC_2400) 822#define IS_2300(isp) ((isp)->isp_type == ISP_HA_FC_2300) 823#define IS_2312(isp) ((isp)->isp_type == ISP_HA_FC_2312) 824#define IS_2322(isp) ((isp)->isp_type == ISP_HA_FC_2322) 825#define IS_24XX(isp) ((isp)->isp_type >= ISP_HA_FC_2400) 826#define IS_25XX(isp) ((isp)->isp_type >= ISP_HA_FC_2500) 827 828/* 829 * DMA related macros 830 */ 831#define DMA_WD3(x) (((uint16_t)(((uint64_t)x) >> 48)) & 0xffff) 832#define DMA_WD2(x) (((uint16_t)(((uint64_t)x) >> 32)) & 0xffff) 833#define DMA_WD1(x) ((uint16_t)((x) >> 16) & 0xffff) 834#define DMA_WD0(x) ((uint16_t)((x) & 0xffff)) 835 836#define DMA_LO32(x) ((uint32_t) (x)) 837#define DMA_HI32(x) ((uint32_t)(((uint64_t)x) >> 32)) 838 839/* 840 * Core System Function Prototypes 841 */ 842 843/* 844 * Reset Hardware. Totally. Assumes that you'll follow this with a call to isp_init. 845 */ 846void isp_reset(ispsoftc_t *, int); 847 848/* 849 * Initialize Hardware to known state 850 */ 851void isp_init(ispsoftc_t *); 852 853/* 854 * Reset the ISP and call completion for any orphaned commands. 855 */ 856void isp_reinit(ispsoftc_t *, int); 857 858/* 859 * Internal Interrupt Service Routine 860 * 861 * The outer layers do the spade work to get the appropriate status register, 862 * semaphore register and first mailbox register (if appropriate). This also 863 * means that most spurious/bogus interrupts not for us can be filtered first. 864 */ 865void isp_intr(ispsoftc_t *, uint32_t, uint16_t, uint16_t); 866 867 868/* 869 * Command Entry Point- Platform Dependent layers call into this 870 */ 871int isp_start(XS_T *); 872 873/* these values are what isp_start returns */ 874#define CMD_COMPLETE 101 /* command completed */ 875#define CMD_EAGAIN 102 /* busy- maybe retry later */ 876#define CMD_QUEUED 103 /* command has been queued for execution */ 877#define CMD_RQLATER 104 /* requeue this command later */ 878 879/* 880 * Command Completion Point- Core layers call out from this with completed cmds 881 */ 882void isp_done(XS_T *); 883 884/* 885 * Platform Dependent to External to Internal Control Function 886 * 887 * Assumes locks are held on entry. You should note that with many of 888 * these commands locks may be released while this function is called. 889 * 890 * ... ISPCTL_RESET_BUS, int channel); 891 * Reset BUS on this channel 892 * ... ISPCTL_RESET_DEV, int channel, int target); 893 * Reset Device on this channel at this target. 894 * ... ISPCTL_ABORT_CMD, XS_T *xs); 895 * Abort active transaction described by xs. 896 * ... IPCTL_UPDATE_PARAMS); 897 * Update any operating parameters (speed, etc.) 898 * ... ISPCTL_FCLINK_TEST, int channel); 899 * Test FC link status on this channel 900 * ... ISPCTL_SCAN_FABRIC, int channel); 901 * Scan fabric on this channel 902 * ... ISPCTL_SCAN_LOOP, int channel); 903 * Scan local loop on this channel 904 * ... ISPCTL_PDB_SYNC, int channel); 905 * Synchronize port database on this channel 906 * ... ISPCTL_SEND_LIP, int channel); 907 * Send a LIP on this channel 908 * ... ISPCTL_GET_NAMES, int channel, int np, uint64_t *wwnn, uint64_t *wwpn) 909 * Get a WWNN/WWPN for this N-port handle on this channel 910 * ... ISPCTL_RUN_MBOXCMD, mbreg_t *mbp) 911 * Run this mailbox command 912 * ... ISPCTL_GET_PDB, int channel, int nphandle, isp_pdb_t *pdb) 913 * Get PDB on this channel for this N-port handle 914 * ... ISPCTL_PLOGX, isp_plcmd_t *) 915 * Performa a port login/logout 916 * 917 * ISPCTL_PDB_SYNC is somewhat misnamed. It actually is the final step, in 918 * order, of ISPCTL_FCLINK_TEST, ISPCTL_SCAN_FABRIC, and ISPCTL_SCAN_LOOP. 919 * The main purpose of ISPCTL_PDB_SYNC is to complete management of logging 920 * and logging out of fabric devices (if one is on a fabric) and then marking 921 * the 'loop state' as being ready to now be used for sending commands to 922 * devices. Originally fabric name server and local loop scanning were 923 * part of this function. It's now been separated to allow for finer control. 924 */ 925typedef enum { 926 ISPCTL_RESET_BUS, 927 ISPCTL_RESET_DEV, 928 ISPCTL_ABORT_CMD, 929 ISPCTL_UPDATE_PARAMS, 930 ISPCTL_FCLINK_TEST, 931 ISPCTL_SCAN_FABRIC, 932 ISPCTL_SCAN_LOOP, 933 ISPCTL_PDB_SYNC, 934 ISPCTL_SEND_LIP, 935 ISPCTL_GET_NAMES, 936 ISPCTL_RUN_MBOXCMD, 937 ISPCTL_GET_PDB, 938 ISPCTL_PLOGX 939} ispctl_t; 940int isp_control(ispsoftc_t *, ispctl_t, ...); 941 942/* 943 * Platform Dependent to Internal to External Control Function 944 */ 945 946typedef enum { 947 ISPASYNC_NEW_TGT_PARAMS, /* SPI New Target Parameters */ 948 ISPASYNC_BUS_RESET, /* All Bus Was Reset */ 949 ISPASYNC_LOOP_DOWN, /* FC Loop Down */ 950 ISPASYNC_LOOP_UP, /* FC Loop Up */ 951 ISPASYNC_LIP, /* FC LIP Received */ 952 ISPASYNC_LOOP_RESET, /* FC Loop Reset Received */ 953 ISPASYNC_CHANGE_NOTIFY, /* FC Change Notification */ 954 ISPASYNC_DEV_ARRIVED, /* FC Device Arrived */ 955 ISPASYNC_DEV_CHANGED, /* FC Device Changed */ 956 ISPASYNC_DEV_STAYED, /* FC Device Stayed */ 957 ISPASYNC_DEV_GONE, /* FC Device Departure */ 958 ISPASYNC_TARGET_NOTIFY, /* All target async notification */ 959 ISPASYNC_TARGET_NOTIFY_ACK, /* All target notify ack required */ 960 ISPASYNC_TARGET_ACTION, /* All target action requested */ 961 ISPASYNC_FW_CRASH, /* All Firmware has crashed */ 962 ISPASYNC_FW_RESTARTED /* All Firmware has been restarted */ 963} ispasync_t; 964void isp_async(ispsoftc_t *, ispasync_t, ...); 965 966#define ISPASYNC_CHANGE_PDB 0 967#define ISPASYNC_CHANGE_SNS 1 968#define ISPASYNC_CHANGE_OTHER 2 969 970/* 971 * Platform Independent Error Prinout 972 */ 973void isp_prt_endcmd(ispsoftc_t *, XS_T *); 974 975/* 976 * Platform Dependent Error and Debug Printout 977 * 978 * Two required functions for each platform must be provided: 979 * 980 * void isp_prt(ispsoftc_t *, int level, const char *, ...) 981 * void isp_xs_prt(ispsoftc_t *, XS_T *, int level, const char *, ...) 982 * 983 * but due to compiler differences on different platforms this won't be 984 * formally defined here. Instead, they go in each platform definition file. 985 */ 986 987#define ISP_LOGALL 0x0 /* log always */ 988#define ISP_LOGCONFIG 0x1 /* log configuration messages */ 989#define ISP_LOGINFO 0x2 /* log informational messages */ 990#define ISP_LOGWARN 0x4 /* log warning messages */ 991#define ISP_LOGERR 0x8 /* log error messages */ 992#define ISP_LOGDEBUG0 0x10 /* log simple debug messages */ 993#define ISP_LOGDEBUG1 0x20 /* log intermediate debug messages */ 994#define ISP_LOGDEBUG2 0x40 /* log most debug messages */ 995#define ISP_LOGDEBUG3 0x80 /* log high frequency debug messages */ 996#define ISP_LOG_SANCFG 0x100 /* log SAN configuration */ 997#define ISP_LOG_CWARN 0x200 /* log SCSI command "warnings" (e.g., check conditions) */ 998#define ISP_LOG_WARN1 0x400 /* log WARNS we might be interested at some time */ 999#define ISP_LOGTINFO 0x1000 /* log informational messages (target mode) */ 1000#define ISP_LOGTDEBUG0 0x2000 /* log simple debug messages (target mode) */ 1001#define ISP_LOGTDEBUG1 0x4000 /* log intermediate debug messages (target) */ 1002#define ISP_LOGTDEBUG2 0x8000 /* log all debug messages (target) */ 1003 1004/* 1005 * Each Platform provides it's own isposinfo substructure of the ispsoftc 1006 * defined above. 1007 * 1008 * Each platform must also provide the following macros/defines: 1009 * 1010 * 1011 * ISP_FC_SCRLEN FC scratch area DMA length 1012 * 1013 * ISP_MEMZERO(dst, src) platform zeroing function 1014 * ISP_MEMCPY(dst, src, count) platform copying function 1015 * ISP_SNPRINTF(buf, bufsize, fmt, ...) snprintf 1016 * ISP_DELAY(usecs) microsecond spindelay function 1017 * ISP_SLEEP(isp, usecs) microsecond sleep function 1018 * 1019 * ISP_INLINE ___inline or not- depending on how 1020 * good your debugger is 1021 * ISP_MIN shorthand for ((a) < (b))? (a) : (b) 1022 * 1023 * NANOTIME_T nanosecond time type 1024 * 1025 * GET_NANOTIME(NANOTIME_T *) get current nanotime. 1026 * 1027 * GET_NANOSEC(NANOTIME_T *) get uint64_t from NANOTIME_T 1028 * 1029 * NANOTIME_SUB(NANOTIME_T *, NANOTIME_T *) 1030 * subtract two NANOTIME_T values 1031 * 1032 * MAXISPREQUEST(ispsoftc_t *) maximum request queue size 1033 * for this particular board type 1034 * 1035 * MEMORYBARRIER(ispsoftc_t *, barrier_type, offset, size, chan) 1036 * 1037 * Function/Macro the provides memory synchronization on 1038 * various objects so that the ISP's and the system's view 1039 * of the same object is consistent. 1040 * 1041 * MBOX_ACQUIRE(ispsoftc_t *) acquire lock on mailbox regs 1042 * MBOX_WAIT_COMPLETE(ispsoftc_t *, mbreg_t *) wait for cmd to be done 1043 * MBOX_NOTIFY_COMPLETE(ispsoftc_t *) notification of mbox cmd donee 1044 * MBOX_RELEASE(ispsoftc_t *) release lock on mailbox regs 1045 * 1046 * FC_SCRATCH_ACQUIRE(ispsoftc_t *, chan) acquire lock on FC scratch area 1047 * return -1 if you cannot 1048 * FC_SCRATCH_RELEASE(ispsoftc_t *, chan) acquire lock on FC scratch area 1049 * 1050 * FCP_NEXT_CRN(ispsoftc_t *, XS_T *, rslt, channel, target, lun) generate the next command reference number. XS_T * may be null. 1051 * 1052 * SCSI_GOOD SCSI 'Good' Status 1053 * SCSI_CHECK SCSI 'Check Condition' Status 1054 * SCSI_BUSY SCSI 'Busy' Status 1055 * SCSI_QFULL SCSI 'Queue Full' Status 1056 * 1057 * XS_T Platform SCSI transaction type (i.e., command for HBA) 1058 * XS_DMA_ADDR_T Platform PCI DMA Address Type 1059 * XS_GET_DMA_SEG(..) Get 32 bit dma segment list value 1060 * XS_GET_DMA64_SEG(..) Get 64 bit dma segment list value 1061 * XS_ISP(xs) gets an instance out of an XS_T 1062 * XS_CHANNEL(xs) gets the channel (bus # for DUALBUS cards) "" 1063 * XS_TGT(xs) gets the target "" 1064 * XS_LUN(xs) gets the lun "" 1065 * XS_CDBP(xs) gets a pointer to the scsi CDB "" 1066 * XS_CDBLEN(xs) gets the CDB's length "" 1067 * XS_XFRLEN(xs) gets the associated data transfer length "" 1068 * XS_TIME(xs) gets the time (in milliseconds) for this command 1069 * XS_GET_RESID(xs) gets the current residual count 1070 * XS_GET_RESID(xs, resid) sets the current residual count 1071 * XS_STSP(xs) gets a pointer to the SCSI status byte "" 1072 * XS_SNSP(xs) gets a pointer to the associate sense data 1073 * XS_TOT_SNSLEN(xs) gets the total length of sense data storage 1074 * XS_CUR_SNSLEN(xs) gets the currently used lenght of sense data storage 1075 * XS_SNSKEY(xs) dereferences XS_SNSP to get the current stored Sense Key 1076 * XS_SNSASC(xs) dereferences XS_SNSP to get the current stored Additional Sense Code 1077 * XS_SNSASCQ(xs) dereferences XS_SNSP to get the current stored Additional Sense Code Qualifier 1078 * XS_TAG_P(xs) predicate of whether this command should be tagged 1079 * XS_TAG_TYPE(xs) which type of tag to use 1080 * XS_SETERR(xs) set error state 1081 * 1082 * HBA_NOERROR command has no erros 1083 * HBA_BOTCH hba botched something 1084 * HBA_CMDTIMEOUT command timed out 1085 * HBA_SELTIMEOUT selection timed out (also port logouts for FC) 1086 * HBA_TGTBSY target returned a BUSY status 1087 * HBA_BUSRESET bus reset destroyed command 1088 * HBA_ABORTED command was aborted (by request) 1089 * HBA_DATAOVR a data overrun was detected 1090 * HBA_ARQFAIL Automatic Request Sense failed 1091 * 1092 * XS_ERR(xs) return current error state 1093 * XS_NOERR(xs) there is no error currently set 1094 * XS_INITERR(xs) initialize error state 1095 * 1096 * XS_SAVE_SENSE(xs, sp, total_len, this_len) save sense data (total and current amount) 1097 * 1098 * XS_APPEND_SENSE(xs, sp, len) append more sense data 1099 * 1100 * XS_SENSE_VALID(xs) indicates whether sense is valid 1101 * 1102 * DEFAULT_FRAMESIZE(ispsoftc_t *) Default Frame Size 1103 * DEFAULT_EXEC_THROTTLE(ispsoftc_t *) Default Execution Throttle 1104 * 1105 * GET_DEFAULT_ROLE(ispsoftc_t *, int) Get Default Role for a channel 1106 * SET_DEFAULT_ROLE(ispsoftc_t *, int, int) Set Default Role for a channel 1107 * DEFAULT_IID(ispsoftc_t *, int) Default SCSI initiator ID 1108 * DEFAULT_LOOPID(ispsoftc_t *, int) Default FC Loop ID 1109 * 1110 * These establish reasonable defaults for each platform. 1111 * These must be available independent of card NVRAM and are 1112 * to be used should NVRAM not be readable. 1113 * 1114 * DEFAULT_NODEWWN(ispsoftc_t *, chan) Default FC Node WWN to use 1115 * DEFAULT_PORTWWN(ispsoftc_t *, chan) Default FC Port WWN to use 1116 * 1117 * These defines are hooks to allow the setting of node and 1118 * port WWNs when NVRAM cannot be read or is to be overriden. 1119 * 1120 * ACTIVE_NODEWWN(ispsoftc_t *, chan) FC Node WWN to use 1121 * ACTIVE_PORTWWN(ispsoftc_t *, chan) FC Port WWN to use 1122 * 1123 * After NVRAM is read, these will be invoked to get the 1124 * node and port WWNs that will actually be used for this 1125 * channel. 1126 * 1127 * 1128 * ISP_IOXPUT_8(ispsoftc_t *, uint8_t srcval, uint8_t *dstptr) 1129 * ISP_IOXPUT_16(ispsoftc_t *, uint16_t srcval, uint16_t *dstptr) 1130 * ISP_IOXPUT_32(ispsoftc_t *, uint32_t srcval, uint32_t *dstptr) 1131 * 1132 * ISP_IOXGET_8(ispsoftc_t *, uint8_t *srcptr, uint8_t dstrval) 1133 * ISP_IOXGET_16(ispsoftc_t *, uint16_t *srcptr, uint16_t dstrval) 1134 * ISP_IOXGET_32(ispsoftc_t *, uint32_t *srcptr, uint32_t dstrval) 1135 * 1136 * ISP_SWIZZLE_NVRAM_WORD(ispsoftc_t *, uint16_t *) 1137 * ISP_SWIZZLE_NVRAM_LONG(ispsoftc_t *, uint32_t *) 1138 * ISP_SWAP16(ispsoftc_t *, uint16_t srcval) 1139 * ISP_SWAP32(ispsoftc_t *, uint32_t srcval) 1140 */ 1141 1142#ifdef ISP_TARGET_MODE 1143/* 1144 * The functions below are for the publicly available 1145 * target mode functions that are internal to the Qlogic driver. 1146 */ 1147 1148/* 1149 * This function handles new response queue entry appropriate for target mode. 1150 */ 1151int isp_target_notify(ispsoftc_t *, void *, uint32_t *); 1152 1153/* 1154 * This function externalizes the ability to acknowledge an Immediate Notify request. 1155 */ 1156int isp_notify_ack(ispsoftc_t *, void *); 1157 1158/* 1159 * This function externalized acknowledging (success/fail) an ABTS frame 1160 */ 1161int isp_acknak_abts(ispsoftc_t *, void *, int); 1162 1163/* 1164 * Enable/Disable/Modify a logical unit. 1165 * (softc, cmd, bus, tgt, lun, cmd_cnt, inotify_cnt) 1166 */ 1167#define DFLT_CMND_CNT 0xff /* unmonitored */ 1168#define DFLT_INOT_CNT 0xff /* unmonitored */ 1169int isp_lun_cmd(ispsoftc_t *, int, int, int, int, int); 1170 1171/* 1172 * General request queue 'put' routine for target mode entries. 1173 */ 1174int isp_target_put_entry(ispsoftc_t *isp, void *); 1175 1176/* 1177 * General routine to put back an ATIO entry- 1178 * used for replenishing f/w resource counts. 1179 * The argument is a pointer to a source ATIO 1180 * or ATIO2. 1181 */ 1182int isp_target_put_atio(ispsoftc_t *, void *); 1183 1184/* 1185 * General routine to send a final CTIO for a command- used mostly for 1186 * local responses. 1187 */ 1188int isp_endcmd(ispsoftc_t *, ...); 1189#define ECMD_SVALID 0x100 1190#define ECMD_TERMINATE 0x200 1191 1192/* 1193 * Handle an asynchronous event 1194 * 1195 * Return nonzero if the interrupt that generated this event has been dismissed. 1196 */ 1197int isp_target_async(ispsoftc_t *, int, int); 1198#endif 1199#endif /* _ISPVAR_H */ 1200