at91sam9g20ek_common.dtsi revision 262569
1/* 2 * at91sam9g20ek_common.dtsi - Device Tree file for Atmel at91sam9g20ek board 3 * 4 * Copyright (C) 2012 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> 5 * 6 * Licensed under GPLv2. 7 */ 8#include "at91sam9g20.dtsi" 9 10/ { 11 12 chosen { 13 bootargs = "mem=64M console=ttyS0,115200 root=/dev/mtdblock5 rw rootfstype=ubifs"; 14 }; 15 16 memory { 17 reg = <0x20000000 0x4000000>; 18 }; 19 20 clocks { 21 #address-cells = <1>; 22 #size-cells = <1>; 23 ranges; 24 25 main_clock: clock@0 { 26 compatible = "atmel,osc", "fixed-clock"; 27 clock-frequency = <18432000>; 28 }; 29 }; 30 31 ahb { 32 apb { 33 pinctrl@fffff400 { 34 board { 35 pinctrl_pck0_as_mck: pck0_as_mck { 36 atmel,pins = 37 <AT91_PIOC 1 AT91_PERIPH_B AT91_PINCTRL_NONE>; /* PC1 periph B */ 38 }; 39 40 }; 41 42 mmc0_slot1 { 43 pinctrl_board_mmc0_slot1: mmc0_slot1-board { 44 atmel,pins = 45 <AT91_PIOC 9 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>; /* PC9 gpio CD pin pull up and deglitch */ 46 }; 47 }; 48 }; 49 50 dbgu: serial@fffff200 { 51 status = "okay"; 52 }; 53 54 usart0: serial@fffb0000 { 55 pinctrl-0 = 56 <&pinctrl_usart0 57 &pinctrl_usart0_rts 58 &pinctrl_usart0_cts 59 &pinctrl_usart0_dtr_dsr 60 &pinctrl_usart0_dcd 61 &pinctrl_usart0_ri>; 62 status = "okay"; 63 }; 64 65 usart1: serial@fffb4000 { 66 status = "okay"; 67 }; 68 69 macb0: ethernet@fffc4000 { 70 phy-mode = "rmii"; 71 status = "okay"; 72 }; 73 74 usb1: gadget@fffa4000 { 75 atmel,vbus-gpio = <&pioC 5 GPIO_ACTIVE_HIGH>; 76 status = "okay"; 77 }; 78 79 mmc0: mmc@fffa8000 { 80 pinctrl-0 = < 81 &pinctrl_board_mmc0_slot1 82 &pinctrl_mmc0_clk 83 &pinctrl_mmc0_slot1_cmd_dat0 84 &pinctrl_mmc0_slot1_dat1_3>; 85 status = "okay"; 86 slot@1 { 87 reg = <1>; 88 bus-width = <4>; 89 cd-gpios = <&pioC 9 GPIO_ACTIVE_HIGH>; 90 }; 91 }; 92 93 ssc0: ssc@fffbc000 { 94 status = "okay"; 95 pinctrl-0 = <&pinctrl_ssc0_tx>; 96 }; 97 98 spi0: spi@fffc8000 { 99 cs-gpios = <0>, <&pioC 11 0>, <0>, <0>; 100 mtd_dataflash@0 { 101 compatible = "atmel,at45", "atmel,dataflash"; 102 spi-max-frequency = <50000000>; 103 reg = <1>; 104 }; 105 }; 106 107 watchdog@fffffd40 { 108 status = "okay"; 109 }; 110 }; 111 112 nand0: nand@40000000 { 113 nand-bus-width = <8>; 114 nand-ecc-mode = "soft"; 115 nand-on-flash-bbt; 116 status = "okay"; 117 118 at91bootstrap@0 { 119 label = "at91bootstrap"; 120 reg = <0x0 0x20000>; 121 }; 122 123 barebox@20000 { 124 label = "barebox"; 125 reg = <0x20000 0x40000>; 126 }; 127 128 bareboxenv@60000 { 129 label = "bareboxenv"; 130 reg = <0x60000 0x20000>; 131 }; 132 133 bareboxenv2@80000 { 134 label = "bareboxenv2"; 135 reg = <0x80000 0x20000>; 136 }; 137 138 oftree@80000 { 139 label = "oftree"; 140 reg = <0xa0000 0x20000>; 141 }; 142 143 kernel@a0000 { 144 label = "kernel"; 145 reg = <0xc0000 0x400000>; 146 }; 147 148 rootfs@4a0000 { 149 label = "rootfs"; 150 reg = <0x4c0000 0x7800000>; 151 }; 152 153 data@7ca0000 { 154 label = "data"; 155 reg = <0x7cc0000 0x8340000>; 156 }; 157 }; 158 159 usb0: ohci@00500000 { 160 num-ports = <2>; 161 status = "okay"; 162 }; 163 }; 164 165 i2c@0 { 166 status = "okay"; 167 168 24c512@50 { 169 compatible = "24c512"; 170 reg = <0x50>; 171 }; 172 173 wm8731: wm8731@1b { 174 compatible = "wm8731"; 175 reg = <0x1b>; 176 }; 177 }; 178 179 gpio_keys { 180 compatible = "gpio-keys"; 181 182 btn3 { 183 label = "Button 3"; 184 gpios = <&pioA 30 GPIO_ACTIVE_LOW>; 185 linux,code = <0x103>; 186 gpio-key,wakeup; 187 }; 188 189 btn4 { 190 label = "Button 4"; 191 gpios = <&pioA 31 GPIO_ACTIVE_LOW>; 192 linux,code = <0x104>; 193 gpio-key,wakeup; 194 }; 195 }; 196 197 sound { 198 compatible = "atmel,at91sam9g20ek-wm8731-audio"; 199 pinctrl-names = "default"; 200 pinctrl-0 = <&pinctrl_pck0_as_mck>; 201 202 atmel,model = "wm8731 @ AT91SAMG20EK"; 203 204 atmel,audio-routing = 205 "Ext Spk", "LHPOUT", 206 "Int Mic", "MICIN"; 207 208 atmel,ssc-controller = <&ssc0>; 209 atmel,audio-codec = <&wm8731>; 210 }; 211}; 212