icsphyreg.h revision 170525
1/* $NetBSD: icsphyreg.h,v 1.2 2003/07/01 22:46:08 msaitoh Exp $ */ 2 3/*- 4 * Copyright (c) 1998 The NetBSD Foundation, Inc. 5 * All rights reserved. 6 * 7 * This code is derived from software contributed to The NetBSD Foundation 8 * by Jason R. Thorpe of the Numerical Aerospace Simulation Facility, 9 * NASA Ames Research Center. 10 * 11 * Redistribution and use in source and binary forms, with or without 12 * modification, are permitted provided that the following conditions 13 * are met: 14 * 1. Redistributions of source code must retain the above copyright 15 * notice, this list of conditions and the following disclaimer. 16 * 2. Redistributions in binary form must reproduce the above copyright 17 * notice, this list of conditions and the following disclaimer in the 18 * documentation and/or other materials provided with the distribution. 19 * 3. All advertising materials mentioning features or use of this software 20 * must display the following acknowledgement: 21 * This product includes software developed by the NetBSD 22 * Foundation, Inc. and its contributors. 23 * 4. Neither the name of The NetBSD Foundation nor the names of its 24 * contributors may be used to endorse or promote products derived 25 * from this software without specific prior written permission. 26 * 27 * THIS SOFTWARE IS PROVIDED BY THE NETBSD FOUNDATION, INC. AND CONTRIBUTORS 28 * ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED 29 * TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR 30 * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE FOUNDATION OR CONTRIBUTORS 31 * BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR 32 * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF 33 * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS 34 * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN 35 * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) 36 * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE 37 * POSSIBILITY OF SUCH DAMAGE. 38 * 39 * $FreeBSD: head/sys/dev/mii/icsphyreg.h 170525 2007-06-11 02:04:50Z yongari $ 40 */ 41 42#ifndef _DEV_MII_ICSPHYREG_H_ 43#define _DEV_MII_ICSPHYREG_H_ 44 45/* 46 * ICS1890 registers. 47 * http://www.icst.com/pdf/18??.pdf 48 */ 49 50/* HEX 1889 1890 1892 1893 51 *-------------------------------------------------------------- 52 * 0 Control * * * * 53 * 1 Status * * * * 54 * 2 PHY Identifier * * * * 55 * 3 PHY Identifier * * * * 56 * 4 Auto-Neg. Advertisement * * * 57 * 5 Auto-Neg. Link Parent Adv * * * 58 * 6 Auto-Neg. Expansion * * * 59 * 7 Auto-Neg. Next Page Tx * * 60 * 8 ANg Nxt Page Lnk Parnt Abl * * 61 * 10 Extended Control * * * * 62 * 11 Quick Poll Status * * * * 63 * 12 10Base-T Operation * * * 64 * 13 Extended Control2 * * * 65 */ 66 67#define MII_ICSPHY_ECR 0x10 /* Extended Control Register */ 68#define ECR_OVR 0x8000 /* disable command reg overwrites */ 69#define ECR_PHYADDR_MASK 0x07c0 /* PHY address mask */ 70#define ECR_CTEST 0x0020 /* Stream Cipher Test Mode */ 71#define ECR_IECT 0x0004 /* Invalid Error Code Test */ 72#define ECR_SSD 0x0001 /* Stream Cipher Disable */ 73 74#define MII_ICSPHY_QPR 0x11 /* Quick Poll Register */ 75#define QPR_SPEED 0x8000 /* 100Mbps */ 76#define QPR_FDX 0x4000 /* Full dupled */ 77#define QPR_ANB2 0x2000 /* Autoneg monitor bit 2 */ 78#define QPR_ANB1 0x1000 /* Autoneg monitor bit 1 */ 79#define QPR_ANB0 0x0800 /* Autoneg monitor bit 0 */ 80#define QPR_RXERR 0x0400 /* Receive signal lost */ 81#define QPR_PLLERR 0x0200 /* PLL error */ 82#define QPR_FCARR 0x0100 /* False carrier detected */ 83#define QPR_INVALSYM 0x0080 /* Invalid Symbol Detected */ 84#define QPR_HALT 0x0040 /* Halt Symbol Detected */ 85#define QPR_PREEM 0x0020 /* Two Idle Symbols together */ 86#define QPR_ACOMP 0x0010 /* Autonegotiation complete */ 87#define QPR_SDETECT 0x0008 /* signal detect */ 88#define QPR_JABBER 0x0004 /* Jabber detected */ 89#define QPR_RFAULT 0x0002 /* Remote Fault */ 90#define QPR_LINK 0x0001 /* Link */ 91 92#define MII_ICSPHY_TTR 0x12 /* 10baseT Operations Register */ 93#define TTR_RJABBER 0x8000 /* Remote Jabber */ 94#define TTR_POLARITY 0x4000 /* Polarity Reversed */ 95#define TTR_NOJABBER 0x0020 /* Disable Jabber Check */ 96#define TTR_LOOP 0x0010 /* Loopback mode */ 97#define TTR_NOAPOLARITY 0x0008 /* Disable auto polarity correction */ 98#define TTR_NOSQE 0x0004 /* Disable SQE check */ 99#define TTR_NOLINK 0x0002 /* Disable Link check */ 100#define TTR_NOSQUELCH 0x0001 /* Disable squelch */ 101 102 103/* 104 * Extended Control Register 2 105 * 106 * HEX 1889 1890 1892 1893 107 *------------------------------------------------------------------- 108 * 8000 Node/Repeater Mode * * * 109 * 4000 Hardware/Software Mode * * * 110 * 2000 Link Partner Support Remote Flt * 111 * 2000 Remote Fault * * 112 * 1000 113 * 0800 114 * 0400 Xmitted Remote Fault status * 115 * 0200 116 * 0100 117 * 0080 Tri-state Enable * 118 * 0040 119 * 0020 120 * 0010 A-N Powerup Remote Flt * 121 * 0008 122 * 0004 123 * 0002 Automatic 10Base-T Power Down * 124 * 0001 Automatic 100Base-TX Power Down * * * 125 */ 126 127#define MII_ICSPHY_ECR2 0x13 /* Extended Control Register 2 */ 128#define ECR2_REPEATER 0x8000 /* Repeater Mode */ 129#define ECR2_HWSW 0x4000 /* hw/sw config priority */ 130#define ECR2_LPRF 0x2000 /* link partner supports rem fault */ 131#define ECR2_FORCERF 0x0400 /* Force transmit of rem fault */ 132#define ECR2_RFPUP 0x0010 /* A-N Powerup Remote fault */ 133#define ECR2_10AUTOPWRDN 0x0002 /* Automatic 10baseT power down */ 134#define ECR2_100AUTOPWRDN 0x0001 /* Automatic 100baseTX power down */ 135 136#endif /* _DEV_MII_ICSPHYREG_H_ */ 137