mb86960.h revision 59874
1/* 2 * All Rights Reserved, Copyright (C) Fujitsu Limited 1995 3 * 4 * This software may be used, modified, copied, distributed, and sold, in 5 * both source and binary form provided that the above copyright, these 6 * terms and the following disclaimer are retained. The name of the author 7 * and/or the contributor may not be used to endorse or promote products 8 * derived from this software without specific prior written permission. 9 * 10 * THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND THE CONTRIBUTOR ``AS IS'' AND 11 * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE 12 * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE 13 * ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR THE CONTRIBUTOR BE LIABLE 14 * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL 15 * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS 16 * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) 17 * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT 18 * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY 19 * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF 20 * SUCH DAMAGE. 21 * 22 * $FreeBSD: head/sys/dev/fe/mb86960.h 59874 2000-05-01 20:32:07Z peter $ 23 */ 24 25/* 26 * Registers of Fujitsu MB86960A/MB86965A series Ethernet controllers. 27 * Written and contributed by M.S. <seki@sysrap.cs.fujitsu.co.jp> 28 */ 29 30/* 31 * Notes on register naming: 32 * 33 * Fujitsu documents for MB86960A/MB86965A uses no mnemorable names 34 * for their registers. They defined only three names for 32 35 * registers and appended numbers to distinguish registers of 36 * same name. Surprisingly, the numbers represent I/O address 37 * offsets of the registers from the base addresses, and their 38 * names correspond to the "bank" the registers are allocated. 39 * All this means that, for example, to say "read DLCR8" has no more 40 * than to say "read a register at offset 8 on bank DLCR." 41 * 42 * The following definitions may look silly, but that's what Fujitsu 43 * did, and it is necessary to know these names to read Fujitsu 44 * documents.. 45 */ 46 47/* Data Link Control Registrs, on invaliant port addresses. */ 48#define FE_DLCR0 0 49#define FE_DLCR1 1 50#define FE_DLCR2 2 51#define FE_DLCR3 3 52#define FE_DLCR4 4 53#define FE_DLCR5 5 54#define FE_DLCR6 6 55#define FE_DLCR7 7 56 57/* More DLCRs, on register bank #0. */ 58#define FE_DLCR8 8 59#define FE_DLCR9 9 60#define FE_DLCR10 10 61#define FE_DLCR11 11 62#define FE_DLCR12 12 63#define FE_DLCR13 13 64#define FE_DLCR14 14 65#define FE_DLCR15 15 66 67/* Malticast Address Registers. On register bank #1. */ 68#define FE_MAR8 8 69#define FE_MAR9 9 70#define FE_MAR10 10 71#define FE_MAR11 11 72#define FE_MAR12 12 73#define FE_MAR13 13 74#define FE_MAR14 14 75#define FE_MAR15 15 76 77/* Buffer Memory Port Registers. On register back #2. */ 78#define FE_BMPR8 8 79#define FE_BMPR9 9 80#define FE_BMPR10 10 81#define FE_BMPR11 11 82#define FE_BMPR12 12 83#define FE_BMPR13 13 84#define FE_BMPR14 14 85#define FE_BMPR15 15 86 87/* More BMPRs, only on 86965, accessible only when JLI mode. */ 88#define FE_BMPR16 16 89#define FE_BMPR17 17 90#define FE_BMPR18 18 91#define FE_BMPR19 19 92 93/* 94 * Definitions of registers. 95 * I don't have Fujitsu documents of MB86960A/MB86965A, so I don't 96 * know the official names for each flags and fields. The following 97 * names are assigned by me (the author of this file,) since I cannot 98 * mnemorize hexadecimal constants for all of these functions. 99 * Comments? 100 * 101 * I've got documents from Fujitsu web site, recently. However, it's 102 * too late. Names for some fields (bits) are kept different from 103 * those used in the Fujitsu documents... 104 */ 105 106/* DLCR0 -- transmitter status */ 107#define FE_D0_BUSERR 0x01 /* Bus write error? */ 108#define FE_D0_COLL16 0x02 /* Collision limit (16) encountered */ 109#define FE_D0_COLLID 0x04 /* Collision on last transmission */ 110#define FE_D0_JABBER 0x08 /* Jabber */ 111#define FE_D0_CRLOST 0x10 /* Carrier lost on last transmission */ 112#define FE_D0_PKTRCD 0x20 /* Last packet looped back correctly */ 113#define FE_D0_NETBSY 0x40 /* Network Busy (Carrier Detected) */ 114#define FE_D0_TXDONE 0x80 /* Transmission complete */ 115 116/* DLCR1 -- receiver status */ 117#define FE_D1_OVRFLO 0x01 /* Receiver buffer overflow */ 118#define FE_D1_CRCERR 0x02 /* CRC error on last packet */ 119#define FE_D1_ALGERR 0x04 /* Alignment error on last packet */ 120#define FE_D1_SRTPKT 0x08 /* Short (RUNT) packet is received */ 121#define FE_D1_RMTRST 0x10 /* Remote reset packet (type = 0x0900) */ 122#define FE_D1_DMAEOP 0x20 /* Host asserted End of DMA OPeration */ 123#define FE_D1_BUSERR 0x40 /* Bus read error */ 124#define FE_D1_PKTRDY 0x80 /* Packet(s) ready on receive buffer */ 125 126/* DLCR2 -- transmitter interrupt control; same layout as DLCR0 */ 127#define FE_D2_BUSERR FE_D0_BUSERR 128#define FE_D2_COLL16 FE_D0_COLL16 129#define FE_D2_COLLID FE_D0_COLLID 130#define FE_D2_JABBER FE_D0_JABBER 131#define FE_D2_TXDONE FE_D0_TXDONE 132 133#define FE_D2_RESERVED 0x70 134 135/* DLCR3 -- receiver interrupt control; same layout as DLCR1 */ 136#define FE_D3_OVRFLO FE_D1_OVRFLO 137#define FE_D3_CRCERR FE_D1_CRCERR 138#define FE_D3_ALGERR FE_D1_ALGERR 139#define FE_D3_SRTPKT FE_D1_SRTPKT 140#define FE_D3_RMTRST FE_D1_RMTRST 141#define FE_D3_DMAEOP FE_D1_DMAEOP 142#define FE_D3_BUSERR FE_D1_BUSERR 143#define FE_D3_PKTRDY FE_D1_PKTRDY 144 145/* DLCR4 -- transmitter operation mode */ 146#define FE_D4_DSC 0x01 /* Disable carrier sense on trans. */ 147#define FE_D4_LBC 0x02 /* Loop back test control */ 148#define FE_D4_CNTRL 0x04 /* - tied to CNTRL pin of the chip */ 149#define FE_D4_TEST1 0x08 /* Test output #1 */ 150#define FE_D4_COL 0xF0 /* Collision counter */ 151 152#define FE_D4_LBC_ENABLE 0x00 /* Perform loop back test */ 153#define FE_D4_LBC_DISABLE 0x02 /* Normal operation */ 154 155#define FE_D4_COL_SHIFT 4 156 157/* DLCR5 -- receiver operation mode */ 158#define FE_D5_AFM0 0x01 /* Receive packets for other stations */ 159#define FE_D5_AFM1 0x02 /* Receive packets for this station */ 160#define FE_D5_RMTRST 0x04 /* Enable remote reset operation */ 161#define FE_D5_SRTPKT 0x08 /* Accept short (RUNT) packets */ 162#define FE_D5_SRTADR 0x10 /* Short (16 bits?) MAC address */ 163#define FE_D5_BADPKT 0x20 /* Accept packets with error */ 164#define FE_D5_BUFEMP 0x40 /* Receive buffer is empty */ 165#define FE_D5_TEST2 0x80 /* Test output #2 */ 166 167/* DLCR6 -- hardware configuration #0 */ 168#define FE_D6_BUFSIZ 0x03 /* Size of NIC buffer SRAM */ 169#define FE_D6_TXBSIZ 0x0C /* Size (and config)of trans. buffer */ 170#define FE_D6_BBW 0x10 /* Buffer SRAM bus width */ 171#define FE_D6_SBW 0x20 /* System bus width */ 172#define FE_D6_SRAM 0x40 /* Buffer SRAM access time */ 173#define FE_D6_DLC 0x80 /* Disable DLC (recever/transmitter) */ 174 175#define FE_D6_BUFSIZ_8KB 0x00 /* The board has 8KB SRAM */ 176#define FE_D6_BUFSIZ_16KB 0x01 /* The board has 16KB SRAM */ 177#define FE_D6_BUFSIZ_32KB 0x02 /* The board has 32KB SRAM */ 178#define FE_D6_BUFSIZ_64KB 0x03 /* The board has 64KB SRAM */ 179 180#define FE_D6_TXBSIZ_1x2KB 0x00 /* Single 2KB buffer for trans. */ 181#define FE_D6_TXBSIZ_2x2KB 0x04 /* Double 2KB buffers */ 182#define FE_D6_TXBSIZ_2x4KB 0x08 /* Double 4KB buffers */ 183#define FE_D6_TXBSIZ_2x8KB 0x0C /* Double 8KB buffers */ 184 185#define FE_D6_BBW_WORD 0x00 /* SRAM has 16 bit data line */ 186#define FE_D6_BBW_BYTE 0x10 /* SRAM has 8 bit data line */ 187 188#define FE_D6_SBW_WORD 0x00 /* Access with 16 bit (AT) bus */ 189#define FE_D6_SBW_BYTE 0x20 /* Access with 8 bit (XT) bus */ 190 191#define FE_D6_SRAM_150ns 0x00 /* The board has slow SRAM */ 192#define FE_D6_SRAM_100ns 0x40 /* The board has fast SRAM */ 193 194#define FE_D6_DLC_ENABLE 0x00 /* Normal operation */ 195#define FE_D6_DLC_DISABLE 0x80 /* Stop sending/receiving */ 196 197/* DLC7 -- hardware configuration #1 */ 198#define FE_D7_BYTSWP 0x01 /* Host byte order control */ 199#define FE_D7_EOPPOL 0x02 /* Polarity of DMA EOP signal */ 200#define FE_D7_RBS 0x0C /* Register bank select */ 201#define FE_D7_RDYPNS 0x10 /* Senses RDYPNSEL input signal */ 202#define FE_D7_POWER 0x20 /* Stand-by (power down) mode control */ 203#define FE_D7_IDENT 0xC0 /* Chip identification */ 204 205#define FE_D7_BYTSWP_LH 0x00 /* DEC/Intel byte order */ 206#define FE_D7_BYTSWP_HL 0x01 /* IBM/Motorolla byte order */ 207 208#define FE_D7_RBS_DLCR 0x00 /* Select DLCR8-15 */ 209#define FE_D7_RBS_MAR 0x04 /* Select MAR8-15 */ 210#define FE_D7_RBS_BMPR 0x08 /* Select BMPR8-15 */ 211 212#define FE_D7_POWER_DOWN 0x00 /* Power down (stand-by) mode */ 213#define FE_D7_POWER_UP 0x20 /* Normal operation */ 214 215#define FE_D7_IDENT_TDK 0x00 /* TDK chips? */ 216#define FE_D7_IDENT_NICE 0x80 /* Fujitsu NICE (86960) */ 217#define FE_D7_IDENT_EC 0xC0 /* Fujitsu EtherCoupler (86965) */ 218 219/* DLCR8 thru DLCR13 are for Ethernet station address. */ 220 221/* DLCR14 and DLCR15 are for TDR. (TDR is used for cable diagnostic.) */ 222 223/* MAR8 thru MAR15 are for Multicast address filter. */ 224 225/* BMPR8 and BMPR9 are for packet data. */ 226 227/* BMPR10 -- transmitter start trigger */ 228#define FE_B10_START 0x80 /* Start transmitter */ 229#define FE_B10_COUNT 0x7F /* Packet count */ 230 231/* BMPR11 -- 16 collisions control */ 232#define FE_B11_CTRL 0x01 /* Skip or resend errored packets */ 233#define FE_B11_MODE1 0x02 /* Restart transmitter after COLL16 */ 234#define FE_B11_MODE2 0x04 /* Automatic restart enable */ 235 236#define FE_B11_CTRL_RESEND 0x00 /* Re-send the collided packet */ 237#define FE_B11_CTRL_SKIP 0x01 /* Skip the collided packet */ 238 239/* BMPR12 -- DMA enable */ 240#define FE_B12_TXDMA 0x01 /* Enable transmitter DMA */ 241#define FE_B12_RXDMA 0x02 /* Enable receiver DMA */ 242 243/* BMPR13 -- DMA control */ 244#define FE_B13_BSTCTL 0x03 /* DMA burst mode control */ 245#define FE_B13_TPTYPE 0x04 /* Twisted pair cable impedance */ 246#define FE_B13_PORT 0x18 /* Port (TP/AUI) selection */ 247#define FE_B13_LNKTST 0x20 /* Link test enable */ 248#define FE_B13_SQTHLD 0x40 /* Lower squelch threshold */ 249#define FE_B13_IOUNLK 0x80 /* Change I/O base address, on JLI mode */ 250 251#define FE_B13_BSTCTL_1 0x00 252#define FE_B13_BSTCTL_4 0x01 253#define FE_B13_BSTCTL_8 0x02 254#define FE_B13_BSTCLT_12 0x03 255 256#define FE_B13_TPTYPE_UTP 0x00 /* Unshielded (standard) cable */ 257#define FE_B13_TPTYPE_STP 0x04 /* Shielded (IBM) cable */ 258 259#define FE_B13_PORT_AUTO 0x00 /* Auto detected */ 260#define FE_B13_PORT_TP 0x08 /* Force TP */ 261#define FE_B13_PORT_AUI 0x18 /* Force AUI */ 262 263/* BMPR14 -- More receiver control and more transmission interrupts */ 264#define FE_B14_FILTER 0x01 /* Filter out self-originated packets */ 265#define FE_B14_SQE 0x02 /* SQE interrupt enable */ 266#define FE_B14_SKIP 0x04 /* Skip a received packet */ 267#define FE_B14_RJAB 0x20 /* RJAB interrupt enable */ 268#define FE_B14_LLD 0x40 /* Local-link-down interrupt enable */ 269#define FE_B14_RLD 0x80 /* Remote-link-down interrupt enable */ 270 271/* BMPR15 -- More transmitter status; basically same layout as BMPR14 */ 272#define FE_B15_SQE FE_B14_SQE 273#define FE_B15_RCVPOL 0x08 /* Reversed receive line polarity */ 274#define FE_B15_RMTPRT 0x10 /* ??? */ 275#define FE_B15_RAJB FE_B14_RJAB 276#define FE_B15_LLD FE_B14_LLD 277#define FE_B15_RLD FE_B14_RLD 278 279/* BMPR16 -- EEPROM control */ 280#define FE_B16_DOUT 0x04 /* EEPROM Data in (CPU to EEPROM) */ 281#define FE_B16_SELECT 0x20 /* EEPROM chip select */ 282#define FE_B16_CLOCK 0x40 /* EEPROM shift clock */ 283#define FE_B16_DIN 0x80 /* EEPROM data out (EEPROM to CPU) */ 284 285/* BMPR17 -- EEPROM data */ 286#define FE_B17_DATA 0x80 /* EEPROM data bit */ 287 288/* BMPR18 -- cycle I/O address setting in JLI mode */ 289 290/* BMPR19 -- ISA interface configuration in JLI mode */ 291#define FE_B19_IRQ 0xC0 292#define FE_B19_IRQ_SHIFT 6 293 294#define FE_B19_ROM 0x38 295#define FE_B19_ROM_SHIFT 3 296 297#define FE_B19_ADDR 0x07 298#define FE_B19_ADDR_SHIFT 0 299 300/* 301 * An extra I/O port address to reset 86965. This location is called 302 * "ID ROM area" by Fujitsu document. 303 */ 304 305/* 306 * Flags in Receive Packet Header... Basically same layout as DLCR1. 307 */ 308#define FE_RPH_OVRFLO FE_D1_OVRFLO 309#define FE_RPH_CRCERR FE_D1_CRCERR 310#define FE_RPH_ALGERR FE_D1_ALGERR 311#define FE_RPH_SRTPKT FE_D1_SRTPKT 312#define FE_RPH_RMTRST FE_D1_RMTRST 313#define FE_RPH_GOOD 0x20 /* Good packet follows */ 314 315/* 316 * EEPROM specification (of JLI mode). 317 */ 318 319/* Number of bytes in an EEPROM accessible through 86965. */ 320#define FE_EEPROM_SIZE 32 321 322/* Offset for JLI config; automatically copied into BMPR19 at startup. */ 323#define FE_EEPROM_CONF 0 324 325/* 326 * Some 8696x specific constants. 327 */ 328 329/* Length (in bytes) of a Multicast Address Filter. */ 330#define FE_FILTER_LEN 8 331 332/* How many packets we can put in the transmission buffer on NIC memory. */ 333#define FE_QUEUEING_MAX 127 334 335/* Length (in bytes) of a "packet length" word in transmission buffer. */ 336#define FE_DATA_LEN_LEN 2 337 338/* Special Multicast Address Filter value. */ 339#define FE_FILTER_NOTHING { 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00 } 340#define FE_FILTER_ALL { 0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF } 341