if_ti.c revision 147805
1/*- 2 * Copyright (c) 1997, 1998, 1999 3 * Bill Paul <wpaul@ctr.columbia.edu>. All rights reserved. 4 * 5 * Redistribution and use in source and binary forms, with or without 6 * modification, are permitted provided that the following conditions 7 * are met: 8 * 1. Redistributions of source code must retain the above copyright 9 * notice, this list of conditions and the following disclaimer. 10 * 2. Redistributions in binary form must reproduce the above copyright 11 * notice, this list of conditions and the following disclaimer in the 12 * documentation and/or other materials provided with the distribution. 13 * 3. All advertising materials mentioning features or use of this software 14 * must display the following acknowledgement: 15 * This product includes software developed by Bill Paul. 16 * 4. Neither the name of the author nor the names of any co-contributors 17 * may be used to endorse or promote products derived from this software 18 * without specific prior written permission. 19 * 20 * THIS SOFTWARE IS PROVIDED BY Bill Paul AND CONTRIBUTORS ``AS IS'' AND 21 * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE 22 * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE 23 * ARE DISCLAIMED. IN NO EVENT SHALL Bill Paul OR THE VOICES IN HIS HEAD 24 * BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR 25 * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF 26 * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS 27 * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN 28 * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) 29 * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF 30 * THE POSSIBILITY OF SUCH DAMAGE. 31 */ 32 33/* 34 * Alteon Networks Tigon PCI gigabit ethernet driver for FreeBSD. 35 * Manuals, sample driver and firmware source kits are available 36 * from http://www.alteon.com/support/openkits. 37 * 38 * Written by Bill Paul <wpaul@ctr.columbia.edu> 39 * Electrical Engineering Department 40 * Columbia University, New York City 41 */ 42 43/* 44 * The Alteon Networks Tigon chip contains an embedded R4000 CPU, 45 * gigabit MAC, dual DMA channels and a PCI interface unit. NICs 46 * using the Tigon may have anywhere from 512K to 2MB of SRAM. The 47 * Tigon supports hardware IP, TCP and UCP checksumming, multicast 48 * filtering and jumbo (9014 byte) frames. The hardware is largely 49 * controlled by firmware, which must be loaded into the NIC during 50 * initialization. 51 * 52 * The Tigon 2 contains 2 R4000 CPUs and requires a newer firmware 53 * revision, which supports new features such as extended commands, 54 * extended jumbo receive ring desciptors and a mini receive ring. 55 * 56 * Alteon Networks is to be commended for releasing such a vast amount 57 * of development material for the Tigon NIC without requiring an NDA 58 * (although they really should have done it a long time ago). With 59 * any luck, the other vendors will finally wise up and follow Alteon's 60 * stellar example. 61 * 62 * The firmware for the Tigon 1 and 2 NICs is compiled directly into 63 * this driver by #including it as a C header file. This bloats the 64 * driver somewhat, but it's the easiest method considering that the 65 * driver code and firmware code need to be kept in sync. The source 66 * for the firmware is not provided with the FreeBSD distribution since 67 * compiling it requires a GNU toolchain targeted for mips-sgi-irix5.3. 68 * 69 * The following people deserve special thanks: 70 * - Terry Murphy of 3Com, for providing a 3c985 Tigon 1 board 71 * for testing 72 * - Raymond Lee of Netgear, for providing a pair of Netgear 73 * GA620 Tigon 2 boards for testing 74 * - Ulf Zimmermann, for bringing the GA260 to my attention and 75 * convincing me to write this driver. 76 * - Andrew Gallatin for providing FreeBSD/Alpha support. 77 */ 78 79#include <sys/cdefs.h> 80__FBSDID("$FreeBSD: head/sys/dev/ti/if_ti.c 147805 2005-07-07 01:05:45Z scottl $"); 81 82#include "opt_ti.h" 83 84#include <sys/param.h> 85#include <sys/systm.h> 86#include <sys/sockio.h> 87#include <sys/mbuf.h> 88#include <sys/malloc.h> 89#include <sys/kernel.h> 90#include <sys/module.h> 91#include <sys/socket.h> 92#include <sys/queue.h> 93#include <sys/conf.h> 94 95#include <net/if.h> 96#include <net/if_arp.h> 97#include <net/ethernet.h> 98#include <net/if_dl.h> 99#include <net/if_media.h> 100#include <net/if_types.h> 101#include <net/if_vlan_var.h> 102 103#include <net/bpf.h> 104 105#include <netinet/in_systm.h> 106#include <netinet/in.h> 107#include <netinet/ip.h> 108 109#include <vm/vm.h> /* for vtophys */ 110#include <vm/pmap.h> /* for vtophys */ 111#include <machine/bus.h> 112#include <machine/resource.h> 113#include <sys/bus.h> 114#include <sys/rman.h> 115 116/* #define TI_PRIVATE_JUMBOS */ 117 118#if !defined(TI_PRIVATE_JUMBOS) 119#include <sys/sockio.h> 120#include <sys/uio.h> 121#include <sys/lock.h> 122#include <sys/sf_buf.h> 123#include <vm/vm_extern.h> 124#include <vm/pmap.h> 125#include <vm/vm_map.h> 126#include <vm/vm_map.h> 127#include <vm/vm_param.h> 128#include <vm/vm_pageout.h> 129#include <sys/vmmeter.h> 130#include <vm/vm_page.h> 131#include <vm/vm_object.h> 132#include <vm/vm_kern.h> 133#include <sys/proc.h> 134#endif /* !TI_PRIVATE_JUMBOS */ 135 136#include <dev/pci/pcireg.h> 137#include <dev/pci/pcivar.h> 138 139#include <sys/tiio.h> 140#include <pci/if_tireg.h> 141#include <pci/ti_fw.h> 142#include <pci/ti_fw2.h> 143 144#define TI_CSUM_FEATURES (CSUM_IP | CSUM_TCP | CSUM_UDP | CSUM_IP_FRAGS) 145/* 146 * We can only turn on header splitting if we're using extended receive 147 * BDs. 148 */ 149#if defined(TI_JUMBO_HDRSPLIT) && defined(TI_PRIVATE_JUMBOS) 150#error "options TI_JUMBO_HDRSPLIT and TI_PRIVATE_JUMBOS are mutually exclusive" 151#endif /* TI_JUMBO_HDRSPLIT && TI_JUMBO_HDRSPLIT */ 152 153struct ti_softc *tis[8]; 154 155typedef enum { 156 TI_SWAP_HTON, 157 TI_SWAP_NTOH 158} ti_swap_type; 159 160 161/* 162 * Various supported device vendors/types and their names. 163 */ 164 165static struct ti_type ti_devs[] = { 166 { ALT_VENDORID, ALT_DEVICEID_ACENIC, 167 "Alteon AceNIC 1000baseSX Gigabit Ethernet" }, 168 { ALT_VENDORID, ALT_DEVICEID_ACENIC_COPPER, 169 "Alteon AceNIC 1000baseT Gigabit Ethernet" }, 170 { TC_VENDORID, TC_DEVICEID_3C985, 171 "3Com 3c985-SX Gigabit Ethernet" }, 172 { NG_VENDORID, NG_DEVICEID_GA620, 173 "Netgear GA620 1000baseSX Gigabit Ethernet" }, 174 { NG_VENDORID, NG_DEVICEID_GA620T, 175 "Netgear GA620 1000baseT Gigabit Ethernet" }, 176 { SGI_VENDORID, SGI_DEVICEID_TIGON, 177 "Silicon Graphics Gigabit Ethernet" }, 178 { DEC_VENDORID, DEC_DEVICEID_FARALLON_PN9000SX, 179 "Farallon PN9000SX Gigabit Ethernet" }, 180 { 0, 0, NULL } 181}; 182 183 184static d_open_t ti_open; 185static d_close_t ti_close; 186static d_ioctl_t ti_ioctl2; 187 188static struct cdevsw ti_cdevsw = { 189 .d_version = D_VERSION, 190 .d_flags = D_NEEDGIANT, 191 .d_open = ti_open, 192 .d_close = ti_close, 193 .d_ioctl = ti_ioctl2, 194 .d_name = "ti", 195}; 196 197static int ti_probe(device_t); 198static int ti_attach(device_t); 199static int ti_detach(device_t); 200static void ti_txeof(struct ti_softc *); 201static void ti_rxeof(struct ti_softc *); 202 203static void ti_stats_update(struct ti_softc *); 204static int ti_encap(struct ti_softc *, struct mbuf *, u_int32_t *); 205 206static void ti_intr(void *); 207static void ti_start(struct ifnet *); 208static int ti_ioctl(struct ifnet *, u_long, caddr_t); 209static void ti_init(void *); 210static void ti_init2(struct ti_softc *); 211static void ti_stop(struct ti_softc *); 212static void ti_watchdog(struct ifnet *); 213static void ti_shutdown(device_t); 214static int ti_ifmedia_upd(struct ifnet *); 215static void ti_ifmedia_sts(struct ifnet *, struct ifmediareq *); 216 217static u_int32_t ti_eeprom_putbyte(struct ti_softc *, int); 218static u_int8_t ti_eeprom_getbyte(struct ti_softc *, int, u_int8_t *); 219static int ti_read_eeprom(struct ti_softc *, caddr_t, int, int); 220 221static void ti_add_mcast(struct ti_softc *, struct ether_addr *); 222static void ti_del_mcast(struct ti_softc *, struct ether_addr *); 223static void ti_setmulti(struct ti_softc *); 224 225static void ti_mem(struct ti_softc *, u_int32_t, u_int32_t, caddr_t); 226static int ti_copy_mem(struct ti_softc *, u_int32_t, u_int32_t, caddr_t, int, int); 227static int ti_copy_scratch(struct ti_softc *, u_int32_t, u_int32_t, caddr_t, 228 int, int, int); 229static int ti_bcopy_swap(const void *, void *, size_t, ti_swap_type); 230static void ti_loadfw(struct ti_softc *); 231static void ti_cmd(struct ti_softc *, struct ti_cmd_desc *); 232static void ti_cmd_ext(struct ti_softc *, struct ti_cmd_desc *, caddr_t, int); 233static void ti_handle_events(struct ti_softc *); 234#ifdef TI_PRIVATE_JUMBOS 235static int ti_alloc_jumbo_mem(struct ti_softc *); 236static void *ti_jalloc(struct ti_softc *); 237static void ti_jfree(void *, void *); 238#endif /* TI_PRIVATE_JUMBOS */ 239static int ti_newbuf_std(struct ti_softc *, int, struct mbuf *); 240static int ti_newbuf_mini(struct ti_softc *, int, struct mbuf *); 241static int ti_newbuf_jumbo(struct ti_softc *, int, struct mbuf *); 242static int ti_init_rx_ring_std(struct ti_softc *); 243static void ti_free_rx_ring_std(struct ti_softc *); 244static int ti_init_rx_ring_jumbo(struct ti_softc *); 245static void ti_free_rx_ring_jumbo(struct ti_softc *); 246static int ti_init_rx_ring_mini(struct ti_softc *); 247static void ti_free_rx_ring_mini(struct ti_softc *); 248static void ti_free_tx_ring(struct ti_softc *); 249static int ti_init_tx_ring(struct ti_softc *); 250 251static int ti_64bitslot_war(struct ti_softc *); 252static int ti_chipinit(struct ti_softc *); 253static int ti_gibinit(struct ti_softc *); 254 255#ifdef TI_JUMBO_HDRSPLIT 256static __inline void ti_hdr_split (struct mbuf *top, int hdr_len, 257 int pkt_len, int idx); 258#endif /* TI_JUMBO_HDRSPLIT */ 259 260static device_method_t ti_methods[] = { 261 /* Device interface */ 262 DEVMETHOD(device_probe, ti_probe), 263 DEVMETHOD(device_attach, ti_attach), 264 DEVMETHOD(device_detach, ti_detach), 265 DEVMETHOD(device_shutdown, ti_shutdown), 266 { 0, 0 } 267}; 268 269static driver_t ti_driver = { 270 "ti", 271 ti_methods, 272 sizeof(struct ti_softc) 273}; 274 275static devclass_t ti_devclass; 276 277DRIVER_MODULE(ti, pci, ti_driver, ti_devclass, 0, 0); 278MODULE_DEPEND(ti, pci, 1, 1, 1); 279MODULE_DEPEND(ti, ether, 1, 1, 1); 280 281/* 282 * Send an instruction or address to the EEPROM, check for ACK. 283 */ 284static u_int32_t ti_eeprom_putbyte(sc, byte) 285 struct ti_softc *sc; 286 int byte; 287{ 288 register int i, ack = 0; 289 290 /* 291 * Make sure we're in TX mode. 292 */ 293 TI_SETBIT(sc, TI_MISC_LOCAL_CTL, TI_MLC_EE_TXEN); 294 295 /* 296 * Feed in each bit and stobe the clock. 297 */ 298 for (i = 0x80; i; i >>= 1) { 299 if (byte & i) { 300 TI_SETBIT(sc, TI_MISC_LOCAL_CTL, TI_MLC_EE_DOUT); 301 } else { 302 TI_CLRBIT(sc, TI_MISC_LOCAL_CTL, TI_MLC_EE_DOUT); 303 } 304 DELAY(1); 305 TI_SETBIT(sc, TI_MISC_LOCAL_CTL, TI_MLC_EE_CLK); 306 DELAY(1); 307 TI_CLRBIT(sc, TI_MISC_LOCAL_CTL, TI_MLC_EE_CLK); 308 } 309 310 /* 311 * Turn off TX mode. 312 */ 313 TI_CLRBIT(sc, TI_MISC_LOCAL_CTL, TI_MLC_EE_TXEN); 314 315 /* 316 * Check for ack. 317 */ 318 TI_SETBIT(sc, TI_MISC_LOCAL_CTL, TI_MLC_EE_CLK); 319 ack = CSR_READ_4(sc, TI_MISC_LOCAL_CTL) & TI_MLC_EE_DIN; 320 TI_CLRBIT(sc, TI_MISC_LOCAL_CTL, TI_MLC_EE_CLK); 321 322 return (ack); 323} 324 325/* 326 * Read a byte of data stored in the EEPROM at address 'addr.' 327 * We have to send two address bytes since the EEPROM can hold 328 * more than 256 bytes of data. 329 */ 330static u_int8_t ti_eeprom_getbyte(sc, addr, dest) 331 struct ti_softc *sc; 332 int addr; 333 u_int8_t *dest; 334{ 335 register int i; 336 u_int8_t byte = 0; 337 338 EEPROM_START; 339 340 /* 341 * Send write control code to EEPROM. 342 */ 343 if (ti_eeprom_putbyte(sc, EEPROM_CTL_WRITE)) { 344 printf("ti%d: failed to send write command, status: %x\n", 345 sc->ti_unit, CSR_READ_4(sc, TI_MISC_LOCAL_CTL)); 346 return (1); 347 } 348 349 /* 350 * Send first byte of address of byte we want to read. 351 */ 352 if (ti_eeprom_putbyte(sc, (addr >> 8) & 0xFF)) { 353 printf("ti%d: failed to send address, status: %x\n", 354 sc->ti_unit, CSR_READ_4(sc, TI_MISC_LOCAL_CTL)); 355 return (1); 356 } 357 /* 358 * Send second byte address of byte we want to read. 359 */ 360 if (ti_eeprom_putbyte(sc, addr & 0xFF)) { 361 printf("ti%d: failed to send address, status: %x\n", 362 sc->ti_unit, CSR_READ_4(sc, TI_MISC_LOCAL_CTL)); 363 return (1); 364 } 365 366 EEPROM_STOP; 367 EEPROM_START; 368 /* 369 * Send read control code to EEPROM. 370 */ 371 if (ti_eeprom_putbyte(sc, EEPROM_CTL_READ)) { 372 printf("ti%d: failed to send read command, status: %x\n", 373 sc->ti_unit, CSR_READ_4(sc, TI_MISC_LOCAL_CTL)); 374 return (1); 375 } 376 377 /* 378 * Start reading bits from EEPROM. 379 */ 380 TI_CLRBIT(sc, TI_MISC_LOCAL_CTL, TI_MLC_EE_TXEN); 381 for (i = 0x80; i; i >>= 1) { 382 TI_SETBIT(sc, TI_MISC_LOCAL_CTL, TI_MLC_EE_CLK); 383 DELAY(1); 384 if (CSR_READ_4(sc, TI_MISC_LOCAL_CTL) & TI_MLC_EE_DIN) 385 byte |= i; 386 TI_CLRBIT(sc, TI_MISC_LOCAL_CTL, TI_MLC_EE_CLK); 387 DELAY(1); 388 } 389 390 EEPROM_STOP; 391 392 /* 393 * No ACK generated for read, so just return byte. 394 */ 395 396 *dest = byte; 397 398 return (0); 399} 400 401/* 402 * Read a sequence of bytes from the EEPROM. 403 */ 404static int 405ti_read_eeprom(sc, dest, off, cnt) 406 struct ti_softc *sc; 407 caddr_t dest; 408 int off; 409 int cnt; 410{ 411 int err = 0, i; 412 u_int8_t byte = 0; 413 414 for (i = 0; i < cnt; i++) { 415 err = ti_eeprom_getbyte(sc, off + i, &byte); 416 if (err) 417 break; 418 *(dest + i) = byte; 419 } 420 421 return (err ? 1 : 0); 422} 423 424/* 425 * NIC memory access function. Can be used to either clear a section 426 * of NIC local memory or (if buf is non-NULL) copy data into it. 427 */ 428static void 429ti_mem(sc, addr, len, buf) 430 struct ti_softc *sc; 431 u_int32_t addr, len; 432 caddr_t buf; 433{ 434 int segptr, segsize, cnt; 435 caddr_t ti_winbase, ptr; 436 437 segptr = addr; 438 cnt = len; 439 ti_winbase = (caddr_t)(sc->ti_vhandle + TI_WINDOW); 440 ptr = buf; 441 442 while (cnt) { 443 if (cnt < TI_WINLEN) 444 segsize = cnt; 445 else 446 segsize = TI_WINLEN - (segptr % TI_WINLEN); 447 CSR_WRITE_4(sc, TI_WINBASE, (segptr & ~(TI_WINLEN - 1))); 448 if (buf == NULL) 449 bzero((char *)ti_winbase + (segptr & 450 (TI_WINLEN - 1)), segsize); 451 else { 452 bcopy((char *)ptr, (char *)ti_winbase + 453 (segptr & (TI_WINLEN - 1)), segsize); 454 ptr += segsize; 455 } 456 segptr += segsize; 457 cnt -= segsize; 458 } 459} 460 461static int 462ti_copy_mem(sc, tigon_addr, len, buf, useraddr, readdata) 463 struct ti_softc *sc; 464 u_int32_t tigon_addr, len; 465 caddr_t buf; 466 int useraddr, readdata; 467{ 468 int segptr, segsize, cnt; 469 caddr_t ptr; 470 u_int32_t origwin; 471 u_int8_t tmparray[TI_WINLEN], tmparray2[TI_WINLEN]; 472 int resid, segresid; 473 int first_pass; 474 475 /* 476 * At the moment, we don't handle non-aligned cases, we just bail. 477 * If this proves to be a problem, it will be fixed. 478 */ 479 if ((readdata == 0) 480 && (tigon_addr & 0x3)) { 481 printf("ti%d: ti_copy_mem: tigon address %#x isn't " 482 "word-aligned\n", sc->ti_unit, tigon_addr); 483 printf("ti%d: ti_copy_mem: unaligned writes aren't yet " 484 "supported\n", sc->ti_unit); 485 return (EINVAL); 486 } 487 488 segptr = tigon_addr & ~0x3; 489 segresid = tigon_addr - segptr; 490 491 /* 492 * This is the non-aligned amount left over that we'll need to 493 * copy. 494 */ 495 resid = len & 0x3; 496 497 /* Add in the left over amount at the front of the buffer */ 498 resid += segresid; 499 500 cnt = len & ~0x3; 501 /* 502 * If resid + segresid is >= 4, add multiples of 4 to the count and 503 * decrease the residual by that much. 504 */ 505 cnt += resid & ~0x3; 506 resid -= resid & ~0x3; 507 508 ptr = buf; 509 510 first_pass = 1; 511 512 /* 513 * Make sure we aren't interrupted while we're changing the window 514 * pointer. 515 */ 516 TI_LOCK(sc); 517 518 /* 519 * Save the old window base value. 520 */ 521 origwin = CSR_READ_4(sc, TI_WINBASE); 522 523 while (cnt) { 524 bus_size_t ti_offset; 525 526 if (cnt < TI_WINLEN) 527 segsize = cnt; 528 else 529 segsize = TI_WINLEN - (segptr % TI_WINLEN); 530 CSR_WRITE_4(sc, TI_WINBASE, (segptr & ~(TI_WINLEN - 1))); 531 532 ti_offset = TI_WINDOW + (segptr & (TI_WINLEN -1)); 533 534 if (readdata) { 535 536 bus_space_read_region_4(sc->ti_btag, 537 sc->ti_bhandle, ti_offset, 538 (u_int32_t *)tmparray, 539 segsize >> 2); 540 if (useraddr) { 541 /* 542 * Yeah, this is a little on the kludgy 543 * side, but at least this code is only 544 * used for debugging. 545 */ 546 ti_bcopy_swap(tmparray, tmparray2, segsize, 547 TI_SWAP_NTOH); 548 549 if (first_pass) { 550 copyout(&tmparray2[segresid], ptr, 551 segsize - segresid); 552 first_pass = 0; 553 } else 554 copyout(tmparray2, ptr, segsize); 555 } else { 556 if (first_pass) { 557 558 ti_bcopy_swap(tmparray, tmparray2, 559 segsize, TI_SWAP_NTOH); 560 bcopy(&tmparray2[segresid], ptr, 561 segsize - segresid); 562 first_pass = 0; 563 } else 564 ti_bcopy_swap(tmparray, ptr, segsize, 565 TI_SWAP_NTOH); 566 } 567 568 } else { 569 if (useraddr) { 570 copyin(ptr, tmparray2, segsize); 571 ti_bcopy_swap(tmparray2, tmparray, segsize, 572 TI_SWAP_HTON); 573 } else 574 ti_bcopy_swap(ptr, tmparray, segsize, 575 TI_SWAP_HTON); 576 577 bus_space_write_region_4(sc->ti_btag, 578 sc->ti_bhandle, ti_offset, 579 (u_int32_t *)tmparray, 580 segsize >> 2); 581 } 582 segptr += segsize; 583 ptr += segsize; 584 cnt -= segsize; 585 } 586 587 /* 588 * Handle leftover, non-word-aligned bytes. 589 */ 590 if (resid != 0) { 591 u_int32_t tmpval, tmpval2; 592 bus_size_t ti_offset; 593 594 /* 595 * Set the segment pointer. 596 */ 597 CSR_WRITE_4(sc, TI_WINBASE, (segptr & ~(TI_WINLEN - 1))); 598 599 ti_offset = TI_WINDOW + (segptr & (TI_WINLEN - 1)); 600 601 /* 602 * First, grab whatever is in our source/destination. 603 * We'll obviously need this for reads, but also for 604 * writes, since we'll be doing read/modify/write. 605 */ 606 bus_space_read_region_4(sc->ti_btag, sc->ti_bhandle, 607 ti_offset, &tmpval, 1); 608 609 /* 610 * Next, translate this from little-endian to big-endian 611 * (at least on i386 boxes). 612 */ 613 tmpval2 = ntohl(tmpval); 614 615 if (readdata) { 616 /* 617 * If we're reading, just copy the leftover number 618 * of bytes from the host byte order buffer to 619 * the user's buffer. 620 */ 621 if (useraddr) 622 copyout(&tmpval2, ptr, resid); 623 else 624 bcopy(&tmpval2, ptr, resid); 625 } else { 626 /* 627 * If we're writing, first copy the bytes to be 628 * written into the network byte order buffer, 629 * leaving the rest of the buffer with whatever was 630 * originally in there. Then, swap the bytes 631 * around into host order and write them out. 632 * 633 * XXX KDM the read side of this has been verified 634 * to work, but the write side of it has not been 635 * verified. So user beware. 636 */ 637 if (useraddr) 638 copyin(ptr, &tmpval2, resid); 639 else 640 bcopy(ptr, &tmpval2, resid); 641 642 tmpval = htonl(tmpval2); 643 644 bus_space_write_region_4(sc->ti_btag, sc->ti_bhandle, 645 ti_offset, &tmpval, 1); 646 } 647 } 648 649 CSR_WRITE_4(sc, TI_WINBASE, origwin); 650 651 TI_UNLOCK(sc); 652 653 return (0); 654} 655 656static int 657ti_copy_scratch(sc, tigon_addr, len, buf, useraddr, readdata, cpu) 658 struct ti_softc *sc; 659 u_int32_t tigon_addr, len; 660 caddr_t buf; 661 int useraddr, readdata; 662 int cpu; 663{ 664 u_int32_t segptr; 665 int cnt; 666 u_int32_t tmpval, tmpval2; 667 caddr_t ptr; 668 669 /* 670 * At the moment, we don't handle non-aligned cases, we just bail. 671 * If this proves to be a problem, it will be fixed. 672 */ 673 if (tigon_addr & 0x3) { 674 printf("ti%d: ti_copy_scratch: tigon address %#x isn't " 675 "word-aligned\n", sc->ti_unit, tigon_addr); 676 return (EINVAL); 677 } 678 679 if (len & 0x3) { 680 printf("ti%d: ti_copy_scratch: transfer length %d isn't " 681 "word-aligned\n", sc->ti_unit, len); 682 return (EINVAL); 683 } 684 685 segptr = tigon_addr; 686 cnt = len; 687 ptr = buf; 688 689 TI_LOCK(sc); 690 691 while (cnt) { 692 CSR_WRITE_4(sc, CPU_REG(TI_SRAM_ADDR, cpu), segptr); 693 694 if (readdata) { 695 tmpval2 = CSR_READ_4(sc, CPU_REG(TI_SRAM_DATA, cpu)); 696 697 tmpval = ntohl(tmpval2); 698 699 /* 700 * Note: I've used this debugging interface 701 * extensively with Alteon's 12.3.15 firmware, 702 * compiled with GCC 2.7.2.1 and binutils 2.9.1. 703 * 704 * When you compile the firmware without 705 * optimization, which is necessary sometimes in 706 * order to properly step through it, you sometimes 707 * read out a bogus value of 0xc0017c instead of 708 * whatever was supposed to be in that scratchpad 709 * location. That value is on the stack somewhere, 710 * but I've never been able to figure out what was 711 * causing the problem. 712 * 713 * The address seems to pop up in random places, 714 * often not in the same place on two subsequent 715 * reads. 716 * 717 * In any case, the underlying data doesn't seem 718 * to be affected, just the value read out. 719 * 720 * KDM, 3/7/2000 721 */ 722 723 if (tmpval2 == 0xc0017c) 724 printf("ti%d: found 0xc0017c at %#x " 725 "(tmpval2)\n", sc->ti_unit, segptr); 726 727 if (tmpval == 0xc0017c) 728 printf("ti%d: found 0xc0017c at %#x " 729 "(tmpval)\n", sc->ti_unit, segptr); 730 731 if (useraddr) 732 copyout(&tmpval, ptr, 4); 733 else 734 bcopy(&tmpval, ptr, 4); 735 } else { 736 if (useraddr) 737 copyin(ptr, &tmpval2, 4); 738 else 739 bcopy(ptr, &tmpval2, 4); 740 741 tmpval = htonl(tmpval2); 742 743 CSR_WRITE_4(sc, CPU_REG(TI_SRAM_DATA, cpu), tmpval); 744 } 745 746 cnt -= 4; 747 segptr += 4; 748 ptr += 4; 749 } 750 751 TI_UNLOCK(sc); 752 753 return (0); 754} 755 756static int 757ti_bcopy_swap(src, dst, len, swap_type) 758 const void *src; 759 void *dst; 760 size_t len; 761 ti_swap_type swap_type; 762{ 763 const u_int8_t *tmpsrc; 764 u_int8_t *tmpdst; 765 size_t tmplen; 766 767 if (len & 0x3) { 768 printf("ti_bcopy_swap: length %zd isn't 32-bit aligned\n", 769 len); 770 return (-1); 771 } 772 773 tmpsrc = src; 774 tmpdst = dst; 775 tmplen = len; 776 777 while (tmplen) { 778 if (swap_type == TI_SWAP_NTOH) 779 *(u_int32_t *)tmpdst = 780 ntohl(*(const u_int32_t *)tmpsrc); 781 else 782 *(u_int32_t *)tmpdst = 783 htonl(*(const u_int32_t *)tmpsrc); 784 785 tmpsrc += 4; 786 tmpdst += 4; 787 tmplen -= 4; 788 } 789 790 return (0); 791} 792 793/* 794 * Load firmware image into the NIC. Check that the firmware revision 795 * is acceptable and see if we want the firmware for the Tigon 1 or 796 * Tigon 2. 797 */ 798static void 799ti_loadfw(sc) 800 struct ti_softc *sc; 801{ 802 switch (sc->ti_hwrev) { 803 case TI_HWREV_TIGON: 804 if (tigonFwReleaseMajor != TI_FIRMWARE_MAJOR || 805 tigonFwReleaseMinor != TI_FIRMWARE_MINOR || 806 tigonFwReleaseFix != TI_FIRMWARE_FIX) { 807 printf("ti%d: firmware revision mismatch; want " 808 "%d.%d.%d, got %d.%d.%d\n", sc->ti_unit, 809 TI_FIRMWARE_MAJOR, TI_FIRMWARE_MINOR, 810 TI_FIRMWARE_FIX, tigonFwReleaseMajor, 811 tigonFwReleaseMinor, tigonFwReleaseFix); 812 return; 813 } 814 ti_mem(sc, tigonFwTextAddr, tigonFwTextLen, 815 (caddr_t)tigonFwText); 816 ti_mem(sc, tigonFwDataAddr, tigonFwDataLen, 817 (caddr_t)tigonFwData); 818 ti_mem(sc, tigonFwRodataAddr, tigonFwRodataLen, 819 (caddr_t)tigonFwRodata); 820 ti_mem(sc, tigonFwBssAddr, tigonFwBssLen, NULL); 821 ti_mem(sc, tigonFwSbssAddr, tigonFwSbssLen, NULL); 822 CSR_WRITE_4(sc, TI_CPU_PROGRAM_COUNTER, tigonFwStartAddr); 823 break; 824 case TI_HWREV_TIGON_II: 825 if (tigon2FwReleaseMajor != TI_FIRMWARE_MAJOR || 826 tigon2FwReleaseMinor != TI_FIRMWARE_MINOR || 827 tigon2FwReleaseFix != TI_FIRMWARE_FIX) { 828 printf("ti%d: firmware revision mismatch; want " 829 "%d.%d.%d, got %d.%d.%d\n", sc->ti_unit, 830 TI_FIRMWARE_MAJOR, TI_FIRMWARE_MINOR, 831 TI_FIRMWARE_FIX, tigon2FwReleaseMajor, 832 tigon2FwReleaseMinor, tigon2FwReleaseFix); 833 return; 834 } 835 ti_mem(sc, tigon2FwTextAddr, tigon2FwTextLen, 836 (caddr_t)tigon2FwText); 837 ti_mem(sc, tigon2FwDataAddr, tigon2FwDataLen, 838 (caddr_t)tigon2FwData); 839 ti_mem(sc, tigon2FwRodataAddr, tigon2FwRodataLen, 840 (caddr_t)tigon2FwRodata); 841 ti_mem(sc, tigon2FwBssAddr, tigon2FwBssLen, NULL); 842 ti_mem(sc, tigon2FwSbssAddr, tigon2FwSbssLen, NULL); 843 CSR_WRITE_4(sc, TI_CPU_PROGRAM_COUNTER, tigon2FwStartAddr); 844 break; 845 default: 846 printf("ti%d: can't load firmware: unknown hardware rev\n", 847 sc->ti_unit); 848 break; 849 } 850} 851 852/* 853 * Send the NIC a command via the command ring. 854 */ 855static void 856ti_cmd(sc, cmd) 857 struct ti_softc *sc; 858 struct ti_cmd_desc *cmd; 859{ 860 u_int32_t index; 861 862 if (sc->ti_rdata->ti_cmd_ring == NULL) 863 return; 864 865 index = sc->ti_cmd_saved_prodidx; 866 CSR_WRITE_4(sc, TI_GCR_CMDRING + (index * 4), *(u_int32_t *)(cmd)); 867 TI_INC(index, TI_CMD_RING_CNT); 868 CSR_WRITE_4(sc, TI_MB_CMDPROD_IDX, index); 869 sc->ti_cmd_saved_prodidx = index; 870} 871 872/* 873 * Send the NIC an extended command. The 'len' parameter specifies the 874 * number of command slots to include after the initial command. 875 */ 876static void 877ti_cmd_ext(sc, cmd, arg, len) 878 struct ti_softc *sc; 879 struct ti_cmd_desc *cmd; 880 caddr_t arg; 881 int len; 882{ 883 u_int32_t index; 884 register int i; 885 886 if (sc->ti_rdata->ti_cmd_ring == NULL) 887 return; 888 889 index = sc->ti_cmd_saved_prodidx; 890 CSR_WRITE_4(sc, TI_GCR_CMDRING + (index * 4), *(u_int32_t *)(cmd)); 891 TI_INC(index, TI_CMD_RING_CNT); 892 for (i = 0; i < len; i++) { 893 CSR_WRITE_4(sc, TI_GCR_CMDRING + (index * 4), 894 *(u_int32_t *)(&arg[i * 4])); 895 TI_INC(index, TI_CMD_RING_CNT); 896 } 897 CSR_WRITE_4(sc, TI_MB_CMDPROD_IDX, index); 898 sc->ti_cmd_saved_prodidx = index; 899} 900 901/* 902 * Handle events that have triggered interrupts. 903 */ 904static void 905ti_handle_events(sc) 906 struct ti_softc *sc; 907{ 908 struct ti_event_desc *e; 909 910 if (sc->ti_rdata->ti_event_ring == NULL) 911 return; 912 913 while (sc->ti_ev_saved_considx != sc->ti_ev_prodidx.ti_idx) { 914 e = &sc->ti_rdata->ti_event_ring[sc->ti_ev_saved_considx]; 915 switch (e->ti_event) { 916 case TI_EV_LINKSTAT_CHANGED: 917 sc->ti_linkstat = e->ti_code; 918 if (e->ti_code == TI_EV_CODE_LINK_UP) 919 printf("ti%d: 10/100 link up\n", sc->ti_unit); 920 else if (e->ti_code == TI_EV_CODE_GIG_LINK_UP) 921 printf("ti%d: gigabit link up\n", sc->ti_unit); 922 else if (e->ti_code == TI_EV_CODE_LINK_DOWN) 923 printf("ti%d: link down\n", sc->ti_unit); 924 break; 925 case TI_EV_ERROR: 926 if (e->ti_code == TI_EV_CODE_ERR_INVAL_CMD) 927 printf("ti%d: invalid command\n", sc->ti_unit); 928 else if (e->ti_code == TI_EV_CODE_ERR_UNIMP_CMD) 929 printf("ti%d: unknown command\n", sc->ti_unit); 930 else if (e->ti_code == TI_EV_CODE_ERR_BADCFG) 931 printf("ti%d: bad config data\n", sc->ti_unit); 932 break; 933 case TI_EV_FIRMWARE_UP: 934 ti_init2(sc); 935 break; 936 case TI_EV_STATS_UPDATED: 937 ti_stats_update(sc); 938 break; 939 case TI_EV_RESET_JUMBO_RING: 940 case TI_EV_MCAST_UPDATED: 941 /* Who cares. */ 942 break; 943 default: 944 printf("ti%d: unknown event: %d\n", 945 sc->ti_unit, e->ti_event); 946 break; 947 } 948 /* Advance the consumer index. */ 949 TI_INC(sc->ti_ev_saved_considx, TI_EVENT_RING_CNT); 950 CSR_WRITE_4(sc, TI_GCR_EVENTCONS_IDX, sc->ti_ev_saved_considx); 951 } 952} 953 954#ifdef TI_PRIVATE_JUMBOS 955 956/* 957 * Memory management for the jumbo receive ring is a pain in the 958 * butt. We need to allocate at least 9018 bytes of space per frame, 959 * _and_ it has to be contiguous (unless you use the extended 960 * jumbo descriptor format). Using malloc() all the time won't 961 * work: malloc() allocates memory in powers of two, which means we 962 * would end up wasting a considerable amount of space by allocating 963 * 9K chunks. We don't have a jumbo mbuf cluster pool. Thus, we have 964 * to do our own memory management. 965 * 966 * The driver needs to allocate a contiguous chunk of memory at boot 967 * time. We then chop this up ourselves into 9K pieces and use them 968 * as external mbuf storage. 969 * 970 * One issue here is how much memory to allocate. The jumbo ring has 971 * 256 slots in it, but at 9K per slot than can consume over 2MB of 972 * RAM. This is a bit much, especially considering we also need 973 * RAM for the standard ring and mini ring (on the Tigon 2). To 974 * save space, we only actually allocate enough memory for 64 slots 975 * by default, which works out to between 500 and 600K. This can 976 * be tuned by changing a #define in if_tireg.h. 977 */ 978 979static int 980ti_alloc_jumbo_mem(sc) 981 struct ti_softc *sc; 982{ 983 caddr_t ptr; 984 register int i; 985 struct ti_jpool_entry *entry; 986 987 /* Grab a big chunk o' storage. */ 988 sc->ti_cdata.ti_jumbo_buf = contigmalloc(TI_JMEM, M_DEVBUF, 989 M_NOWAIT, 0, 0xffffffff, PAGE_SIZE, 0); 990 991 if (sc->ti_cdata.ti_jumbo_buf == NULL) { 992 printf("ti%d: no memory for jumbo buffers!\n", sc->ti_unit); 993 return (ENOBUFS); 994 } 995 996 SLIST_INIT(&sc->ti_jfree_listhead); 997 SLIST_INIT(&sc->ti_jinuse_listhead); 998 999 /* 1000 * Now divide it up into 9K pieces and save the addresses 1001 * in an array. 1002 */ 1003 ptr = sc->ti_cdata.ti_jumbo_buf; 1004 for (i = 0; i < TI_JSLOTS; i++) { 1005 sc->ti_cdata.ti_jslots[i] = ptr; 1006 ptr += TI_JLEN; 1007 entry = malloc(sizeof(struct ti_jpool_entry), 1008 M_DEVBUF, M_NOWAIT); 1009 if (entry == NULL) { 1010 contigfree(sc->ti_cdata.ti_jumbo_buf, TI_JMEM, 1011 M_DEVBUF); 1012 sc->ti_cdata.ti_jumbo_buf = NULL; 1013 printf("ti%d: no memory for jumbo " 1014 "buffer queue!\n", sc->ti_unit); 1015 return (ENOBUFS); 1016 } 1017 entry->slot = i; 1018 SLIST_INSERT_HEAD(&sc->ti_jfree_listhead, entry, jpool_entries); 1019 } 1020 1021 return (0); 1022} 1023 1024/* 1025 * Allocate a jumbo buffer. 1026 */ 1027static void *ti_jalloc(sc) 1028 struct ti_softc *sc; 1029{ 1030 struct ti_jpool_entry *entry; 1031 1032 entry = SLIST_FIRST(&sc->ti_jfree_listhead); 1033 1034 if (entry == NULL) { 1035 printf("ti%d: no free jumbo buffers\n", sc->ti_unit); 1036 return (NULL); 1037 } 1038 1039 SLIST_REMOVE_HEAD(&sc->ti_jfree_listhead, jpool_entries); 1040 SLIST_INSERT_HEAD(&sc->ti_jinuse_listhead, entry, jpool_entries); 1041 return (sc->ti_cdata.ti_jslots[entry->slot]); 1042} 1043 1044/* 1045 * Release a jumbo buffer. 1046 */ 1047static void 1048ti_jfree(buf, args) 1049 void *buf; 1050 void *args; 1051{ 1052 struct ti_softc *sc; 1053 int i; 1054 struct ti_jpool_entry *entry; 1055 1056 /* Extract the softc struct pointer. */ 1057 sc = (struct ti_softc *)args; 1058 1059 if (sc == NULL) 1060 panic("ti_jfree: didn't get softc pointer!"); 1061 1062 /* calculate the slot this buffer belongs to */ 1063 i = ((vm_offset_t)buf 1064 - (vm_offset_t)sc->ti_cdata.ti_jumbo_buf) / TI_JLEN; 1065 1066 if ((i < 0) || (i >= TI_JSLOTS)) 1067 panic("ti_jfree: asked to free buffer that we don't manage!"); 1068 1069 entry = SLIST_FIRST(&sc->ti_jinuse_listhead); 1070 if (entry == NULL) 1071 panic("ti_jfree: buffer not in use!"); 1072 entry->slot = i; 1073 SLIST_REMOVE_HEAD(&sc->ti_jinuse_listhead, jpool_entries); 1074 SLIST_INSERT_HEAD(&sc->ti_jfree_listhead, entry, jpool_entries); 1075} 1076 1077#endif /* TI_PRIVATE_JUMBOS */ 1078 1079/* 1080 * Intialize a standard receive ring descriptor. 1081 */ 1082static int 1083ti_newbuf_std(sc, i, m) 1084 struct ti_softc *sc; 1085 int i; 1086 struct mbuf *m; 1087{ 1088 struct mbuf *m_new = NULL; 1089 struct ti_rx_desc *r; 1090 1091 if (m == NULL) { 1092 MGETHDR(m_new, M_DONTWAIT, MT_DATA); 1093 if (m_new == NULL) 1094 return (ENOBUFS); 1095 1096 MCLGET(m_new, M_DONTWAIT); 1097 if (!(m_new->m_flags & M_EXT)) { 1098 m_freem(m_new); 1099 return (ENOBUFS); 1100 } 1101 m_new->m_len = m_new->m_pkthdr.len = MCLBYTES; 1102 } else { 1103 m_new = m; 1104 m_new->m_len = m_new->m_pkthdr.len = MCLBYTES; 1105 m_new->m_data = m_new->m_ext.ext_buf; 1106 } 1107 1108 m_adj(m_new, ETHER_ALIGN); 1109 sc->ti_cdata.ti_rx_std_chain[i] = m_new; 1110 r = &sc->ti_rdata->ti_rx_std_ring[i]; 1111 TI_HOSTADDR(r->ti_addr) = vtophys(mtod(m_new, caddr_t)); 1112 r->ti_type = TI_BDTYPE_RECV_BD; 1113 r->ti_flags = 0; 1114 if (sc->ti_ifp->if_hwassist) 1115 r->ti_flags |= TI_BDFLAG_TCP_UDP_CKSUM | TI_BDFLAG_IP_CKSUM; 1116 r->ti_len = m_new->m_len; 1117 r->ti_idx = i; 1118 1119 return (0); 1120} 1121 1122/* 1123 * Intialize a mini receive ring descriptor. This only applies to 1124 * the Tigon 2. 1125 */ 1126static int 1127ti_newbuf_mini(sc, i, m) 1128 struct ti_softc *sc; 1129 int i; 1130 struct mbuf *m; 1131{ 1132 struct mbuf *m_new = NULL; 1133 struct ti_rx_desc *r; 1134 1135 if (m == NULL) { 1136 MGETHDR(m_new, M_DONTWAIT, MT_DATA); 1137 if (m_new == NULL) { 1138 return (ENOBUFS); 1139 } 1140 m_new->m_len = m_new->m_pkthdr.len = MHLEN; 1141 } else { 1142 m_new = m; 1143 m_new->m_data = m_new->m_pktdat; 1144 m_new->m_len = m_new->m_pkthdr.len = MHLEN; 1145 } 1146 1147 m_adj(m_new, ETHER_ALIGN); 1148 r = &sc->ti_rdata->ti_rx_mini_ring[i]; 1149 sc->ti_cdata.ti_rx_mini_chain[i] = m_new; 1150 TI_HOSTADDR(r->ti_addr) = vtophys(mtod(m_new, caddr_t)); 1151 r->ti_type = TI_BDTYPE_RECV_BD; 1152 r->ti_flags = TI_BDFLAG_MINI_RING; 1153 if (sc->ti_ifp->if_hwassist) 1154 r->ti_flags |= TI_BDFLAG_TCP_UDP_CKSUM | TI_BDFLAG_IP_CKSUM; 1155 r->ti_len = m_new->m_len; 1156 r->ti_idx = i; 1157 1158 return (0); 1159} 1160 1161#ifdef TI_PRIVATE_JUMBOS 1162 1163/* 1164 * Initialize a jumbo receive ring descriptor. This allocates 1165 * a jumbo buffer from the pool managed internally by the driver. 1166 */ 1167static int 1168ti_newbuf_jumbo(sc, i, m) 1169 struct ti_softc *sc; 1170 int i; 1171 struct mbuf *m; 1172{ 1173 struct mbuf *m_new = NULL; 1174 struct ti_rx_desc *r; 1175 1176 if (m == NULL) { 1177 caddr_t *buf = NULL; 1178 1179 /* Allocate the mbuf. */ 1180 MGETHDR(m_new, M_DONTWAIT, MT_DATA); 1181 if (m_new == NULL) { 1182 return (ENOBUFS); 1183 } 1184 1185 /* Allocate the jumbo buffer */ 1186 buf = ti_jalloc(sc); 1187 if (buf == NULL) { 1188 m_freem(m_new); 1189 printf("ti%d: jumbo allocation failed " 1190 "-- packet dropped!\n", sc->ti_unit); 1191 return (ENOBUFS); 1192 } 1193 1194 /* Attach the buffer to the mbuf. */ 1195 m_new->m_data = (void *) buf; 1196 m_new->m_len = m_new->m_pkthdr.len = TI_JUMBO_FRAMELEN; 1197 MEXTADD(m_new, buf, TI_JUMBO_FRAMELEN, ti_jfree, 1198 (struct ti_softc *)sc, 0, EXT_NET_DRV); 1199 } else { 1200 m_new = m; 1201 m_new->m_data = m_new->m_ext.ext_buf; 1202 m_new->m_ext.ext_size = TI_JUMBO_FRAMELEN; 1203 } 1204 1205 m_adj(m_new, ETHER_ALIGN); 1206 /* Set up the descriptor. */ 1207 r = &sc->ti_rdata->ti_rx_jumbo_ring[i]; 1208 sc->ti_cdata.ti_rx_jumbo_chain[i] = m_new; 1209 TI_HOSTADDR(r->ti_addr) = vtophys(mtod(m_new, caddr_t)); 1210 r->ti_type = TI_BDTYPE_RECV_JUMBO_BD; 1211 r->ti_flags = TI_BDFLAG_JUMBO_RING; 1212 if (sc->ti_ifp->if_hwassist) 1213 r->ti_flags |= TI_BDFLAG_TCP_UDP_CKSUM | TI_BDFLAG_IP_CKSUM; 1214 r->ti_len = m_new->m_len; 1215 r->ti_idx = i; 1216 1217 return (0); 1218} 1219 1220#else 1221#include <vm/vm_page.h> 1222 1223#if (PAGE_SIZE == 4096) 1224#define NPAYLOAD 2 1225#else 1226#define NPAYLOAD 1 1227#endif 1228 1229#define TCP_HDR_LEN (52 + sizeof(struct ether_header)) 1230#define UDP_HDR_LEN (28 + sizeof(struct ether_header)) 1231#define NFS_HDR_LEN (UDP_HDR_LEN) 1232static int HDR_LEN = TCP_HDR_LEN; 1233 1234 1235/* 1236 * Initialize a jumbo receive ring descriptor. This allocates 1237 * a jumbo buffer from the pool managed internally by the driver. 1238 */ 1239static int 1240ti_newbuf_jumbo(sc, idx, m_old) 1241 struct ti_softc *sc; 1242 int idx; 1243 struct mbuf *m_old; 1244{ 1245 struct mbuf *cur, *m_new = NULL; 1246 struct mbuf *m[3] = {NULL, NULL, NULL}; 1247 struct ti_rx_desc_ext *r; 1248 vm_page_t frame; 1249 static int color; 1250 /* 1 extra buf to make nobufs easy*/ 1251 struct sf_buf *sf[3] = {NULL, NULL, NULL}; 1252 int i; 1253 1254 if (m_old != NULL) { 1255 m_new = m_old; 1256 cur = m_old->m_next; 1257 for (i = 0; i <= NPAYLOAD; i++){ 1258 m[i] = cur; 1259 cur = cur->m_next; 1260 } 1261 } else { 1262 /* Allocate the mbufs. */ 1263 MGETHDR(m_new, M_DONTWAIT, MT_DATA); 1264 if (m_new == NULL) { 1265 printf("ti%d: mbuf allocation failed " 1266 "-- packet dropped!\n", sc->ti_unit); 1267 goto nobufs; 1268 } 1269 MGET(m[NPAYLOAD], M_DONTWAIT, MT_DATA); 1270 if (m[NPAYLOAD] == NULL) { 1271 printf("ti%d: cluster mbuf allocation failed " 1272 "-- packet dropped!\n", sc->ti_unit); 1273 goto nobufs; 1274 } 1275 MCLGET(m[NPAYLOAD], M_DONTWAIT); 1276 if ((m[NPAYLOAD]->m_flags & M_EXT) == 0) { 1277 printf("ti%d: mbuf allocation failed " 1278 "-- packet dropped!\n", sc->ti_unit); 1279 goto nobufs; 1280 } 1281 m[NPAYLOAD]->m_len = MCLBYTES; 1282 1283 for (i = 0; i < NPAYLOAD; i++){ 1284 MGET(m[i], M_DONTWAIT, MT_DATA); 1285 if (m[i] == NULL) { 1286 printf("ti%d: mbuf allocation failed " 1287 "-- packet dropped!\n", sc->ti_unit); 1288 goto nobufs; 1289 } 1290 frame = vm_page_alloc(NULL, color++, 1291 VM_ALLOC_INTERRUPT | VM_ALLOC_NOOBJ | 1292 VM_ALLOC_WIRED); 1293 if (frame == NULL) { 1294 printf("ti%d: buffer allocation failed " 1295 "-- packet dropped!\n", sc->ti_unit); 1296 printf(" index %d page %d\n", idx, i); 1297 goto nobufs; 1298 } 1299 sf[i] = sf_buf_alloc(frame, SFB_NOWAIT); 1300 if (sf[i] == NULL) { 1301 vm_page_lock_queues(); 1302 vm_page_unwire(frame, 0); 1303 vm_page_free(frame); 1304 vm_page_unlock_queues(); 1305 printf("ti%d: buffer allocation failed " 1306 "-- packet dropped!\n", sc->ti_unit); 1307 printf(" index %d page %d\n", idx, i); 1308 goto nobufs; 1309 } 1310 } 1311 for (i = 0; i < NPAYLOAD; i++){ 1312 /* Attach the buffer to the mbuf. */ 1313 m[i]->m_data = (void *)sf_buf_kva(sf[i]); 1314 m[i]->m_len = PAGE_SIZE; 1315 MEXTADD(m[i], sf_buf_kva(sf[i]), PAGE_SIZE, 1316 sf_buf_mext, sf[i], 0, EXT_DISPOSABLE); 1317 m[i]->m_next = m[i+1]; 1318 } 1319 /* link the buffers to the header */ 1320 m_new->m_next = m[0]; 1321 m_new->m_data += ETHER_ALIGN; 1322 if (sc->ti_hdrsplit) 1323 m_new->m_len = MHLEN - ETHER_ALIGN; 1324 else 1325 m_new->m_len = HDR_LEN; 1326 m_new->m_pkthdr.len = NPAYLOAD * PAGE_SIZE + m_new->m_len; 1327 } 1328 1329 /* Set up the descriptor. */ 1330 r = &sc->ti_rdata->ti_rx_jumbo_ring[idx]; 1331 sc->ti_cdata.ti_rx_jumbo_chain[idx] = m_new; 1332 TI_HOSTADDR(r->ti_addr0) = vtophys(mtod(m_new, caddr_t)); 1333 r->ti_len0 = m_new->m_len; 1334 1335 TI_HOSTADDR(r->ti_addr1) = vtophys(mtod(m[0], caddr_t)); 1336 r->ti_len1 = PAGE_SIZE; 1337 1338 TI_HOSTADDR(r->ti_addr2) = vtophys(mtod(m[1], caddr_t)); 1339 r->ti_len2 = m[1]->m_ext.ext_size; /* could be PAGE_SIZE or MCLBYTES */ 1340 1341 if (PAGE_SIZE == 4096) { 1342 TI_HOSTADDR(r->ti_addr3) = vtophys(mtod(m[2], caddr_t)); 1343 r->ti_len3 = MCLBYTES; 1344 } else { 1345 r->ti_len3 = 0; 1346 } 1347 r->ti_type = TI_BDTYPE_RECV_JUMBO_BD; 1348 1349 r->ti_flags = TI_BDFLAG_JUMBO_RING|TI_RCB_FLAG_USE_EXT_RX_BD; 1350 1351 if (sc->ti_ifp->if_hwassist) 1352 r->ti_flags |= TI_BDFLAG_TCP_UDP_CKSUM|TI_BDFLAG_IP_CKSUM; 1353 1354 r->ti_idx = idx; 1355 1356 return (0); 1357 1358nobufs: 1359 1360 /* 1361 * Warning! : 1362 * This can only be called before the mbufs are strung together. 1363 * If the mbufs are strung together, m_freem() will free the chain, 1364 * so that the later mbufs will be freed multiple times. 1365 */ 1366 if (m_new) 1367 m_freem(m_new); 1368 1369 for (i = 0; i < 3; i++) { 1370 if (m[i]) 1371 m_freem(m[i]); 1372 if (sf[i]) 1373 sf_buf_mext((void *)sf_buf_kva(sf[i]), sf[i]); 1374 } 1375 return (ENOBUFS); 1376} 1377#endif 1378 1379 1380 1381/* 1382 * The standard receive ring has 512 entries in it. At 2K per mbuf cluster, 1383 * that's 1MB or memory, which is a lot. For now, we fill only the first 1384 * 256 ring entries and hope that our CPU is fast enough to keep up with 1385 * the NIC. 1386 */ 1387static int 1388ti_init_rx_ring_std(sc) 1389 struct ti_softc *sc; 1390{ 1391 register int i; 1392 struct ti_cmd_desc cmd; 1393 1394 for (i = 0; i < TI_SSLOTS; i++) { 1395 if (ti_newbuf_std(sc, i, NULL) == ENOBUFS) 1396 return (ENOBUFS); 1397 }; 1398 1399 TI_UPDATE_STDPROD(sc, i - 1); 1400 sc->ti_std = i - 1; 1401 1402 return (0); 1403} 1404 1405static void 1406ti_free_rx_ring_std(sc) 1407 struct ti_softc *sc; 1408{ 1409 register int i; 1410 1411 for (i = 0; i < TI_STD_RX_RING_CNT; i++) { 1412 if (sc->ti_cdata.ti_rx_std_chain[i] != NULL) { 1413 m_freem(sc->ti_cdata.ti_rx_std_chain[i]); 1414 sc->ti_cdata.ti_rx_std_chain[i] = NULL; 1415 } 1416 bzero((char *)&sc->ti_rdata->ti_rx_std_ring[i], 1417 sizeof(struct ti_rx_desc)); 1418 } 1419} 1420 1421static int 1422ti_init_rx_ring_jumbo(sc) 1423 struct ti_softc *sc; 1424{ 1425 register int i; 1426 struct ti_cmd_desc cmd; 1427 1428 for (i = 0; i < TI_JUMBO_RX_RING_CNT; i++) { 1429 if (ti_newbuf_jumbo(sc, i, NULL) == ENOBUFS) 1430 return (ENOBUFS); 1431 }; 1432 1433 TI_UPDATE_JUMBOPROD(sc, i - 1); 1434 sc->ti_jumbo = i - 1; 1435 1436 return (0); 1437} 1438 1439static void 1440ti_free_rx_ring_jumbo(sc) 1441 struct ti_softc *sc; 1442{ 1443 register int i; 1444 1445 for (i = 0; i < TI_JUMBO_RX_RING_CNT; i++) { 1446 if (sc->ti_cdata.ti_rx_jumbo_chain[i] != NULL) { 1447 m_freem(sc->ti_cdata.ti_rx_jumbo_chain[i]); 1448 sc->ti_cdata.ti_rx_jumbo_chain[i] = NULL; 1449 } 1450 bzero((char *)&sc->ti_rdata->ti_rx_jumbo_ring[i], 1451 sizeof(struct ti_rx_desc)); 1452 } 1453} 1454 1455static int 1456ti_init_rx_ring_mini(sc) 1457 struct ti_softc *sc; 1458{ 1459 register int i; 1460 1461 for (i = 0; i < TI_MSLOTS; i++) { 1462 if (ti_newbuf_mini(sc, i, NULL) == ENOBUFS) 1463 return (ENOBUFS); 1464 }; 1465 1466 TI_UPDATE_MINIPROD(sc, i - 1); 1467 sc->ti_mini = i - 1; 1468 1469 return (0); 1470} 1471 1472static void 1473ti_free_rx_ring_mini(sc) 1474 struct ti_softc *sc; 1475{ 1476 register int i; 1477 1478 for (i = 0; i < TI_MINI_RX_RING_CNT; i++) { 1479 if (sc->ti_cdata.ti_rx_mini_chain[i] != NULL) { 1480 m_freem(sc->ti_cdata.ti_rx_mini_chain[i]); 1481 sc->ti_cdata.ti_rx_mini_chain[i] = NULL; 1482 } 1483 bzero((char *)&sc->ti_rdata->ti_rx_mini_ring[i], 1484 sizeof(struct ti_rx_desc)); 1485 } 1486} 1487 1488static void 1489ti_free_tx_ring(sc) 1490 struct ti_softc *sc; 1491{ 1492 register int i; 1493 1494 if (sc->ti_rdata->ti_tx_ring == NULL) 1495 return; 1496 1497 for (i = 0; i < TI_TX_RING_CNT; i++) { 1498 if (sc->ti_cdata.ti_tx_chain[i] != NULL) { 1499 m_freem(sc->ti_cdata.ti_tx_chain[i]); 1500 sc->ti_cdata.ti_tx_chain[i] = NULL; 1501 } 1502 bzero((char *)&sc->ti_rdata->ti_tx_ring[i], 1503 sizeof(struct ti_tx_desc)); 1504 } 1505} 1506 1507static int 1508ti_init_tx_ring(sc) 1509 struct ti_softc *sc; 1510{ 1511 sc->ti_txcnt = 0; 1512 sc->ti_tx_saved_considx = 0; 1513 CSR_WRITE_4(sc, TI_MB_SENDPROD_IDX, 0); 1514 return (0); 1515} 1516 1517/* 1518 * The Tigon 2 firmware has a new way to add/delete multicast addresses, 1519 * but we have to support the old way too so that Tigon 1 cards will 1520 * work. 1521 */ 1522static void 1523ti_add_mcast(sc, addr) 1524 struct ti_softc *sc; 1525 struct ether_addr *addr; 1526{ 1527 struct ti_cmd_desc cmd; 1528 u_int16_t *m; 1529 u_int32_t ext[2] = {0, 0}; 1530 1531 m = (u_int16_t *)&addr->octet[0]; 1532 1533 switch (sc->ti_hwrev) { 1534 case TI_HWREV_TIGON: 1535 CSR_WRITE_4(sc, TI_GCR_MAR0, htons(m[0])); 1536 CSR_WRITE_4(sc, TI_GCR_MAR1, (htons(m[1]) << 16) | htons(m[2])); 1537 TI_DO_CMD(TI_CMD_ADD_MCAST_ADDR, 0, 0); 1538 break; 1539 case TI_HWREV_TIGON_II: 1540 ext[0] = htons(m[0]); 1541 ext[1] = (htons(m[1]) << 16) | htons(m[2]); 1542 TI_DO_CMD_EXT(TI_CMD_EXT_ADD_MCAST, 0, 0, (caddr_t)&ext, 2); 1543 break; 1544 default: 1545 printf("ti%d: unknown hwrev\n", sc->ti_unit); 1546 break; 1547 } 1548} 1549 1550static void 1551ti_del_mcast(sc, addr) 1552 struct ti_softc *sc; 1553 struct ether_addr *addr; 1554{ 1555 struct ti_cmd_desc cmd; 1556 u_int16_t *m; 1557 u_int32_t ext[2] = {0, 0}; 1558 1559 m = (u_int16_t *)&addr->octet[0]; 1560 1561 switch (sc->ti_hwrev) { 1562 case TI_HWREV_TIGON: 1563 CSR_WRITE_4(sc, TI_GCR_MAR0, htons(m[0])); 1564 CSR_WRITE_4(sc, TI_GCR_MAR1, (htons(m[1]) << 16) | htons(m[2])); 1565 TI_DO_CMD(TI_CMD_DEL_MCAST_ADDR, 0, 0); 1566 break; 1567 case TI_HWREV_TIGON_II: 1568 ext[0] = htons(m[0]); 1569 ext[1] = (htons(m[1]) << 16) | htons(m[2]); 1570 TI_DO_CMD_EXT(TI_CMD_EXT_DEL_MCAST, 0, 0, (caddr_t)&ext, 2); 1571 break; 1572 default: 1573 printf("ti%d: unknown hwrev\n", sc->ti_unit); 1574 break; 1575 } 1576} 1577 1578/* 1579 * Configure the Tigon's multicast address filter. 1580 * 1581 * The actual multicast table management is a bit of a pain, thanks to 1582 * slight brain damage on the part of both Alteon and us. With our 1583 * multicast code, we are only alerted when the multicast address table 1584 * changes and at that point we only have the current list of addresses: 1585 * we only know the current state, not the previous state, so we don't 1586 * actually know what addresses were removed or added. The firmware has 1587 * state, but we can't get our grubby mits on it, and there is no 'delete 1588 * all multicast addresses' command. Hence, we have to maintain our own 1589 * state so we know what addresses have been programmed into the NIC at 1590 * any given time. 1591 */ 1592static void 1593ti_setmulti(sc) 1594 struct ti_softc *sc; 1595{ 1596 struct ifnet *ifp; 1597 struct ifmultiaddr *ifma; 1598 struct ti_cmd_desc cmd; 1599 struct ti_mc_entry *mc; 1600 u_int32_t intrs; 1601 1602 ifp = sc->ti_ifp; 1603 1604 if (ifp->if_flags & IFF_ALLMULTI) { 1605 TI_DO_CMD(TI_CMD_SET_ALLMULTI, TI_CMD_CODE_ALLMULTI_ENB, 0); 1606 return; 1607 } else { 1608 TI_DO_CMD(TI_CMD_SET_ALLMULTI, TI_CMD_CODE_ALLMULTI_DIS, 0); 1609 } 1610 1611 /* Disable interrupts. */ 1612 intrs = CSR_READ_4(sc, TI_MB_HOSTINTR); 1613 CSR_WRITE_4(sc, TI_MB_HOSTINTR, 1); 1614 1615 /* First, zot all the existing filters. */ 1616 while (SLIST_FIRST(&sc->ti_mc_listhead) != NULL) { 1617 mc = SLIST_FIRST(&sc->ti_mc_listhead); 1618 ti_del_mcast(sc, &mc->mc_addr); 1619 SLIST_REMOVE_HEAD(&sc->ti_mc_listhead, mc_entries); 1620 free(mc, M_DEVBUF); 1621 } 1622 1623 /* Now program new ones. */ 1624 TAILQ_FOREACH(ifma, &ifp->if_multiaddrs, ifma_link) { 1625 if (ifma->ifma_addr->sa_family != AF_LINK) 1626 continue; 1627 mc = malloc(sizeof(struct ti_mc_entry), M_DEVBUF, M_NOWAIT); 1628 if (mc == NULL) { 1629 if_printf(ifp, "no memory for mcast filter entry\n"); 1630 continue; 1631 } 1632 bcopy(LLADDR((struct sockaddr_dl *)ifma->ifma_addr), 1633 (char *)&mc->mc_addr, ETHER_ADDR_LEN); 1634 SLIST_INSERT_HEAD(&sc->ti_mc_listhead, mc, mc_entries); 1635 ti_add_mcast(sc, &mc->mc_addr); 1636 } 1637 1638 /* Re-enable interrupts. */ 1639 CSR_WRITE_4(sc, TI_MB_HOSTINTR, intrs); 1640} 1641 1642/* 1643 * Check to see if the BIOS has configured us for a 64 bit slot when 1644 * we aren't actually in one. If we detect this condition, we can work 1645 * around it on the Tigon 2 by setting a bit in the PCI state register, 1646 * but for the Tigon 1 we must give up and abort the interface attach. 1647 */ 1648static int ti_64bitslot_war(sc) 1649 struct ti_softc *sc; 1650{ 1651 if (!(CSR_READ_4(sc, TI_PCI_STATE) & TI_PCISTATE_32BIT_BUS)) { 1652 CSR_WRITE_4(sc, 0x600, 0); 1653 CSR_WRITE_4(sc, 0x604, 0); 1654 CSR_WRITE_4(sc, 0x600, 0x5555AAAA); 1655 if (CSR_READ_4(sc, 0x604) == 0x5555AAAA) { 1656 if (sc->ti_hwrev == TI_HWREV_TIGON) 1657 return (EINVAL); 1658 else { 1659 TI_SETBIT(sc, TI_PCI_STATE, 1660 TI_PCISTATE_32BIT_BUS); 1661 return (0); 1662 } 1663 } 1664 } 1665 1666 return (0); 1667} 1668 1669/* 1670 * Do endian, PCI and DMA initialization. Also check the on-board ROM 1671 * self-test results. 1672 */ 1673static int 1674ti_chipinit(sc) 1675 struct ti_softc *sc; 1676{ 1677 u_int32_t cacheline; 1678 u_int32_t pci_writemax = 0; 1679 u_int32_t hdrsplit; 1680 1681 /* Initialize link to down state. */ 1682 sc->ti_linkstat = TI_EV_CODE_LINK_DOWN; 1683 1684 if (sc->ti_ifp->if_capenable & IFCAP_HWCSUM) 1685 sc->ti_ifp->if_hwassist = TI_CSUM_FEATURES; 1686 else 1687 sc->ti_ifp->if_hwassist = 0; 1688 1689 /* Set endianness before we access any non-PCI registers. */ 1690#if BYTE_ORDER == BIG_ENDIAN 1691 CSR_WRITE_4(sc, TI_MISC_HOST_CTL, 1692 TI_MHC_BIGENDIAN_INIT | (TI_MHC_BIGENDIAN_INIT << 24)); 1693#else 1694 CSR_WRITE_4(sc, TI_MISC_HOST_CTL, 1695 TI_MHC_LITTLEENDIAN_INIT | (TI_MHC_LITTLEENDIAN_INIT << 24)); 1696#endif 1697 1698 /* Check the ROM failed bit to see if self-tests passed. */ 1699 if (CSR_READ_4(sc, TI_CPU_STATE) & TI_CPUSTATE_ROMFAIL) { 1700 printf("ti%d: board self-diagnostics failed!\n", sc->ti_unit); 1701 return (ENODEV); 1702 } 1703 1704 /* Halt the CPU. */ 1705 TI_SETBIT(sc, TI_CPU_STATE, TI_CPUSTATE_HALT); 1706 1707 /* Figure out the hardware revision. */ 1708 switch (CSR_READ_4(sc, TI_MISC_HOST_CTL) & TI_MHC_CHIP_REV_MASK) { 1709 case TI_REV_TIGON_I: 1710 sc->ti_hwrev = TI_HWREV_TIGON; 1711 break; 1712 case TI_REV_TIGON_II: 1713 sc->ti_hwrev = TI_HWREV_TIGON_II; 1714 break; 1715 default: 1716 printf("ti%d: unsupported chip revision\n", sc->ti_unit); 1717 return (ENODEV); 1718 } 1719 1720 /* Do special setup for Tigon 2. */ 1721 if (sc->ti_hwrev == TI_HWREV_TIGON_II) { 1722 TI_SETBIT(sc, TI_CPU_CTL_B, TI_CPUSTATE_HALT); 1723 TI_SETBIT(sc, TI_MISC_LOCAL_CTL, TI_MLC_SRAM_BANK_512K); 1724 TI_SETBIT(sc, TI_MISC_CONF, TI_MCR_SRAM_SYNCHRONOUS); 1725 } 1726 1727 /* 1728 * We don't have firmware source for the Tigon 1, so Tigon 1 boards 1729 * can't do header splitting. 1730 */ 1731#ifdef TI_JUMBO_HDRSPLIT 1732 if (sc->ti_hwrev != TI_HWREV_TIGON) 1733 sc->ti_hdrsplit = 1; 1734 else 1735 printf("ti%d: can't do header splitting on a Tigon I board\n", 1736 sc->ti_unit); 1737#endif /* TI_JUMBO_HDRSPLIT */ 1738 1739 /* Set up the PCI state register. */ 1740 CSR_WRITE_4(sc, TI_PCI_STATE, TI_PCI_READ_CMD|TI_PCI_WRITE_CMD); 1741 if (sc->ti_hwrev == TI_HWREV_TIGON_II) { 1742 TI_SETBIT(sc, TI_PCI_STATE, TI_PCISTATE_USE_MEM_RD_MULT); 1743 } 1744 1745 /* Clear the read/write max DMA parameters. */ 1746 TI_CLRBIT(sc, TI_PCI_STATE, (TI_PCISTATE_WRITE_MAXDMA| 1747 TI_PCISTATE_READ_MAXDMA)); 1748 1749 /* Get cache line size. */ 1750 cacheline = CSR_READ_4(sc, TI_PCI_BIST) & 0xFF; 1751 1752 /* 1753 * If the system has set enabled the PCI memory write 1754 * and invalidate command in the command register, set 1755 * the write max parameter accordingly. This is necessary 1756 * to use MWI with the Tigon 2. 1757 */ 1758 if (CSR_READ_4(sc, TI_PCI_CMDSTAT) & PCIM_CMD_MWIEN) { 1759 switch (cacheline) { 1760 case 1: 1761 case 4: 1762 case 8: 1763 case 16: 1764 case 32: 1765 case 64: 1766 break; 1767 default: 1768 /* Disable PCI memory write and invalidate. */ 1769 if (bootverbose) 1770 printf("ti%d: cache line size %d not " 1771 "supported; disabling PCI MWI\n", 1772 sc->ti_unit, cacheline); 1773 CSR_WRITE_4(sc, TI_PCI_CMDSTAT, CSR_READ_4(sc, 1774 TI_PCI_CMDSTAT) & ~PCIM_CMD_MWIEN); 1775 break; 1776 } 1777 } 1778 1779#ifdef __brokenalpha__ 1780 /* 1781 * From the Alteon sample driver: 1782 * Must insure that we do not cross an 8K (bytes) boundary 1783 * for DMA reads. Our highest limit is 1K bytes. This is a 1784 * restriction on some ALPHA platforms with early revision 1785 * 21174 PCI chipsets, such as the AlphaPC 164lx 1786 */ 1787 TI_SETBIT(sc, TI_PCI_STATE, pci_writemax|TI_PCI_READMAX_1024); 1788#else 1789 TI_SETBIT(sc, TI_PCI_STATE, pci_writemax); 1790#endif 1791 1792 /* This sets the min dma param all the way up (0xff). */ 1793 TI_SETBIT(sc, TI_PCI_STATE, TI_PCISTATE_MINDMA); 1794 1795 if (sc->ti_hdrsplit) 1796 hdrsplit = TI_OPMODE_JUMBO_HDRSPLIT; 1797 else 1798 hdrsplit = 0; 1799 1800 /* Configure DMA variables. */ 1801#if BYTE_ORDER == BIG_ENDIAN 1802 CSR_WRITE_4(sc, TI_GCR_OPMODE, TI_OPMODE_BYTESWAP_BD | 1803 TI_OPMODE_BYTESWAP_DATA | TI_OPMODE_WORDSWAP_BD | 1804 TI_OPMODE_WARN_ENB | TI_OPMODE_FATAL_ENB | 1805 TI_OPMODE_DONT_FRAG_JUMBO | hdrsplit); 1806#else /* BYTE_ORDER */ 1807 CSR_WRITE_4(sc, TI_GCR_OPMODE, TI_OPMODE_BYTESWAP_DATA| 1808 TI_OPMODE_WORDSWAP_BD|TI_OPMODE_DONT_FRAG_JUMBO| 1809 TI_OPMODE_WARN_ENB|TI_OPMODE_FATAL_ENB | hdrsplit); 1810#endif /* BYTE_ORDER */ 1811 1812 /* 1813 * Only allow 1 DMA channel to be active at a time. 1814 * I don't think this is a good idea, but without it 1815 * the firmware racks up lots of nicDmaReadRingFull 1816 * errors. This is not compatible with hardware checksums. 1817 */ 1818 if (sc->ti_ifp->if_hwassist == 0) 1819 TI_SETBIT(sc, TI_GCR_OPMODE, TI_OPMODE_1_DMA_ACTIVE); 1820 1821 /* Recommended settings from Tigon manual. */ 1822 CSR_WRITE_4(sc, TI_GCR_DMA_WRITECFG, TI_DMA_STATE_THRESH_8W); 1823 CSR_WRITE_4(sc, TI_GCR_DMA_READCFG, TI_DMA_STATE_THRESH_8W); 1824 1825 if (ti_64bitslot_war(sc)) { 1826 printf("ti%d: bios thinks we're in a 64 bit slot, " 1827 "but we aren't", sc->ti_unit); 1828 return (EINVAL); 1829 } 1830 1831 return (0); 1832} 1833 1834#define TI_RD_OFF(x) offsetof(struct ti_ring_data, x) 1835 1836/* 1837 * Initialize the general information block and firmware, and 1838 * start the CPU(s) running. 1839 */ 1840static int 1841ti_gibinit(sc) 1842 struct ti_softc *sc; 1843{ 1844 struct ti_rcb *rcb; 1845 int i; 1846 struct ifnet *ifp; 1847 uint32_t rdphys; 1848 1849 ifp = sc->ti_ifp; 1850 rdphys = sc->ti_rdata_phys; 1851 1852 /* Disable interrupts for now. */ 1853 CSR_WRITE_4(sc, TI_MB_HOSTINTR, 1); 1854 1855 /* 1856 * Tell the chip where to find the general information block. 1857 * While this struct could go into >4GB memory, we allocate it in a 1858 * single slab with the other descriptors, and those don't seem to 1859 * support being located in a 64-bit region. 1860 */ 1861 CSR_WRITE_4(sc, TI_GCR_GENINFO_HI, 0); 1862 CSR_WRITE_4(sc, TI_GCR_GENINFO_LO, rdphys + TI_RD_OFF(ti_info)); 1863 1864 /* Load the firmware into SRAM. */ 1865 ti_loadfw(sc); 1866 1867 /* Set up the contents of the general info and ring control blocks. */ 1868 1869 /* Set up the event ring and producer pointer. */ 1870 rcb = &sc->ti_rdata->ti_info.ti_ev_rcb; 1871 1872 TI_HOSTADDR(rcb->ti_hostaddr) = rdphys + TI_RD_OFF(ti_event_ring); 1873 rcb->ti_flags = 0; 1874 TI_HOSTADDR(sc->ti_rdata->ti_info.ti_ev_prodidx_ptr) = 1875 rdphys + TI_RD_OFF(ti_ev_prodidx_r); 1876 sc->ti_ev_prodidx.ti_idx = 0; 1877 CSR_WRITE_4(sc, TI_GCR_EVENTCONS_IDX, 0); 1878 sc->ti_ev_saved_considx = 0; 1879 1880 /* Set up the command ring and producer mailbox. */ 1881 rcb = &sc->ti_rdata->ti_info.ti_cmd_rcb; 1882 1883 sc->ti_rdata->ti_cmd_ring = 1884 (struct ti_cmd_desc *)(sc->ti_vhandle + TI_GCR_CMDRING); 1885 TI_HOSTADDR(rcb->ti_hostaddr) = TI_GCR_NIC_ADDR(TI_GCR_CMDRING); 1886 rcb->ti_flags = 0; 1887 rcb->ti_max_len = 0; 1888 for (i = 0; i < TI_CMD_RING_CNT; i++) { 1889 CSR_WRITE_4(sc, TI_GCR_CMDRING + (i * 4), 0); 1890 } 1891 CSR_WRITE_4(sc, TI_GCR_CMDCONS_IDX, 0); 1892 CSR_WRITE_4(sc, TI_MB_CMDPROD_IDX, 0); 1893 sc->ti_cmd_saved_prodidx = 0; 1894 1895 /* 1896 * Assign the address of the stats refresh buffer. 1897 * We re-use the current stats buffer for this to 1898 * conserve memory. 1899 */ 1900 TI_HOSTADDR(sc->ti_rdata->ti_info.ti_refresh_stats_ptr) = 1901 rdphys + TI_RD_OFF(ti_info.ti_stats); 1902 1903 /* Set up the standard receive ring. */ 1904 rcb = &sc->ti_rdata->ti_info.ti_std_rx_rcb; 1905 TI_HOSTADDR(rcb->ti_hostaddr) = rdphys + TI_RD_OFF(ti_rx_std_ring); 1906 rcb->ti_max_len = TI_FRAMELEN; 1907 rcb->ti_flags = 0; 1908 if (sc->ti_ifp->if_hwassist) 1909 rcb->ti_flags |= TI_RCB_FLAG_TCP_UDP_CKSUM | 1910 TI_RCB_FLAG_IP_CKSUM | TI_RCB_FLAG_NO_PHDR_CKSUM; 1911 rcb->ti_flags |= TI_RCB_FLAG_VLAN_ASSIST; 1912 1913 /* Set up the jumbo receive ring. */ 1914 rcb = &sc->ti_rdata->ti_info.ti_jumbo_rx_rcb; 1915 TI_HOSTADDR(rcb->ti_hostaddr) = rdphys + TI_RD_OFF(ti_rx_jumbo_ring); 1916 1917#ifdef TI_PRIVATE_JUMBOS 1918 rcb->ti_max_len = TI_JUMBO_FRAMELEN; 1919 rcb->ti_flags = 0; 1920#else 1921 rcb->ti_max_len = PAGE_SIZE; 1922 rcb->ti_flags = TI_RCB_FLAG_USE_EXT_RX_BD; 1923#endif 1924 if (sc->ti_ifp->if_hwassist) 1925 rcb->ti_flags |= TI_RCB_FLAG_TCP_UDP_CKSUM | 1926 TI_RCB_FLAG_IP_CKSUM | TI_RCB_FLAG_NO_PHDR_CKSUM; 1927 rcb->ti_flags |= TI_RCB_FLAG_VLAN_ASSIST; 1928 1929 /* 1930 * Set up the mini ring. Only activated on the 1931 * Tigon 2 but the slot in the config block is 1932 * still there on the Tigon 1. 1933 */ 1934 rcb = &sc->ti_rdata->ti_info.ti_mini_rx_rcb; 1935 TI_HOSTADDR(rcb->ti_hostaddr) = rdphys + TI_RD_OFF(ti_rx_mini_ring); 1936 rcb->ti_max_len = MHLEN - ETHER_ALIGN; 1937 if (sc->ti_hwrev == TI_HWREV_TIGON) 1938 rcb->ti_flags = TI_RCB_FLAG_RING_DISABLED; 1939 else 1940 rcb->ti_flags = 0; 1941 if (sc->ti_ifp->if_hwassist) 1942 rcb->ti_flags |= TI_RCB_FLAG_TCP_UDP_CKSUM | 1943 TI_RCB_FLAG_IP_CKSUM | TI_RCB_FLAG_NO_PHDR_CKSUM; 1944 rcb->ti_flags |= TI_RCB_FLAG_VLAN_ASSIST; 1945 1946 /* 1947 * Set up the receive return ring. 1948 */ 1949 rcb = &sc->ti_rdata->ti_info.ti_return_rcb; 1950 TI_HOSTADDR(rcb->ti_hostaddr) = rdphys + TI_RD_OFF(ti_rx_return_ring); 1951 rcb->ti_flags = 0; 1952 rcb->ti_max_len = TI_RETURN_RING_CNT; 1953 TI_HOSTADDR(sc->ti_rdata->ti_info.ti_return_prodidx_ptr) = 1954 rdphys + TI_RD_OFF(ti_return_prodidx_r); 1955 1956 /* 1957 * Set up the tx ring. Note: for the Tigon 2, we have the option 1958 * of putting the transmit ring in the host's address space and 1959 * letting the chip DMA it instead of leaving the ring in the NIC's 1960 * memory and accessing it through the shared memory region. We 1961 * do this for the Tigon 2, but it doesn't work on the Tigon 1, 1962 * so we have to revert to the shared memory scheme if we detect 1963 * a Tigon 1 chip. 1964 */ 1965 CSR_WRITE_4(sc, TI_WINBASE, TI_TX_RING_BASE); 1966 if (sc->ti_hwrev == TI_HWREV_TIGON) { 1967 sc->ti_rdata->ti_tx_ring_nic = 1968 (struct ti_tx_desc *)(sc->ti_vhandle + TI_WINDOW); 1969 } 1970 bzero((char *)sc->ti_rdata->ti_tx_ring, 1971 TI_TX_RING_CNT * sizeof(struct ti_tx_desc)); 1972 rcb = &sc->ti_rdata->ti_info.ti_tx_rcb; 1973 if (sc->ti_hwrev == TI_HWREV_TIGON) 1974 rcb->ti_flags = 0; 1975 else 1976 rcb->ti_flags = TI_RCB_FLAG_HOST_RING; 1977 rcb->ti_flags |= TI_RCB_FLAG_VLAN_ASSIST; 1978 if (sc->ti_ifp->if_hwassist) 1979 rcb->ti_flags |= TI_RCB_FLAG_TCP_UDP_CKSUM | 1980 TI_RCB_FLAG_IP_CKSUM | TI_RCB_FLAG_NO_PHDR_CKSUM; 1981 rcb->ti_max_len = TI_TX_RING_CNT; 1982 if (sc->ti_hwrev == TI_HWREV_TIGON) 1983 TI_HOSTADDR(rcb->ti_hostaddr) = TI_TX_RING_BASE; 1984 else 1985 TI_HOSTADDR(rcb->ti_hostaddr) = rdphys + TI_RD_OFF(ti_tx_ring); 1986 TI_HOSTADDR(sc->ti_rdata->ti_info.ti_tx_considx_ptr) = 1987 rdphys + TI_RD_OFF(ti_tx_considx_r); 1988 1989 /* Set up tuneables */ 1990#if 0 1991 if (ifp->if_mtu > (ETHERMTU + ETHER_HDR_LEN + ETHER_CRC_LEN)) 1992 CSR_WRITE_4(sc, TI_GCR_RX_COAL_TICKS, 1993 (sc->ti_rx_coal_ticks / 10)); 1994 else 1995#endif 1996 CSR_WRITE_4(sc, TI_GCR_RX_COAL_TICKS, sc->ti_rx_coal_ticks); 1997 CSR_WRITE_4(sc, TI_GCR_TX_COAL_TICKS, sc->ti_tx_coal_ticks); 1998 CSR_WRITE_4(sc, TI_GCR_STAT_TICKS, sc->ti_stat_ticks); 1999 CSR_WRITE_4(sc, TI_GCR_RX_MAX_COAL_BD, sc->ti_rx_max_coal_bds); 2000 CSR_WRITE_4(sc, TI_GCR_TX_MAX_COAL_BD, sc->ti_tx_max_coal_bds); 2001 CSR_WRITE_4(sc, TI_GCR_TX_BUFFER_RATIO, sc->ti_tx_buf_ratio); 2002 2003 /* Turn interrupts on. */ 2004 CSR_WRITE_4(sc, TI_GCR_MASK_INTRS, 0); 2005 CSR_WRITE_4(sc, TI_MB_HOSTINTR, 0); 2006 2007 /* Start CPU. */ 2008 TI_CLRBIT(sc, TI_CPU_STATE, (TI_CPUSTATE_HALT|TI_CPUSTATE_STEP)); 2009 2010 return (0); 2011} 2012 2013static void 2014ti_rdata_cb(void *arg, bus_dma_segment_t *segs, int nseg, int error) 2015{ 2016 struct ti_softc *sc; 2017 2018 sc = arg; 2019 if (error || nseg != 1) 2020 return; 2021 2022 /* 2023 * All of the Tigon data structures need to live at <4GB. This 2024 * cast is fine since busdma was told about this constraint. 2025 */ 2026 sc->ti_rdata_phys = (uint32_t)segs[0].ds_addr; 2027 return; 2028} 2029 2030/* 2031 * Probe for a Tigon chip. Check the PCI vendor and device IDs 2032 * against our list and return its name if we find a match. 2033 */ 2034static int 2035ti_probe(dev) 2036 device_t dev; 2037{ 2038 struct ti_type *t; 2039 2040 t = ti_devs; 2041 2042 while (t->ti_name != NULL) { 2043 if ((pci_get_vendor(dev) == t->ti_vid) && 2044 (pci_get_device(dev) == t->ti_did)) { 2045 device_set_desc(dev, t->ti_name); 2046 return (BUS_PROBE_DEFAULT); 2047 } 2048 t++; 2049 } 2050 2051 return (ENXIO); 2052} 2053 2054static int 2055ti_attach(dev) 2056 device_t dev; 2057{ 2058 struct ifnet *ifp; 2059 struct ti_softc *sc; 2060 int unit, error = 0, rid; 2061 u_char eaddr[6]; 2062 2063 sc = device_get_softc(dev); 2064 unit = device_get_unit(dev); 2065 sc->ti_unit = unit; 2066 2067 mtx_init(&sc->ti_mtx, device_get_nameunit(dev), MTX_NETWORK_LOCK, 2068 MTX_DEF | MTX_RECURSE); 2069 ifmedia_init(&sc->ifmedia, IFM_IMASK, ti_ifmedia_upd, ti_ifmedia_sts); 2070 ifp = sc->ti_ifp = if_alloc(IFT_ETHER); 2071 if (ifp == NULL) { 2072 printf("ti%d: can not if_alloc()\n", sc->ti_unit); 2073 error = ENOSPC; 2074 goto fail; 2075 } 2076 sc->ti_ifp->if_capabilities = IFCAP_HWCSUM | 2077 IFCAP_VLAN_HWTAGGING | IFCAP_VLAN_MTU; 2078 sc->ti_ifp->if_capenable = sc->ti_ifp->if_capabilities; 2079 2080 /* 2081 * Map control/status registers. 2082 */ 2083 pci_enable_busmaster(dev); 2084 2085 rid = TI_PCI_LOMEM; 2086 sc->ti_res = bus_alloc_resource_any(dev, SYS_RES_MEMORY, &rid, 2087 RF_ACTIVE|PCI_RF_DENSE); 2088 2089 if (sc->ti_res == NULL) { 2090 printf ("ti%d: couldn't map memory\n", unit); 2091 error = ENXIO; 2092 goto fail; 2093 } 2094 2095 sc->ti_btag = rman_get_bustag(sc->ti_res); 2096 sc->ti_bhandle = rman_get_bushandle(sc->ti_res); 2097 sc->ti_vhandle = (vm_offset_t)rman_get_virtual(sc->ti_res); 2098 2099 /* Allocate interrupt */ 2100 rid = 0; 2101 2102 sc->ti_irq = bus_alloc_resource_any(dev, SYS_RES_IRQ, &rid, 2103 RF_SHAREABLE | RF_ACTIVE); 2104 2105 if (sc->ti_irq == NULL) { 2106 printf("ti%d: couldn't map interrupt\n", unit); 2107 error = ENXIO; 2108 goto fail; 2109 } 2110 2111 if (ti_chipinit(sc)) { 2112 printf("ti%d: chip initialization failed\n", sc->ti_unit); 2113 error = ENXIO; 2114 goto fail; 2115 } 2116 2117 /* Zero out the NIC's on-board SRAM. */ 2118 ti_mem(sc, 0x2000, 0x100000 - 0x2000, NULL); 2119 2120 /* Init again -- zeroing memory may have clobbered some registers. */ 2121 if (ti_chipinit(sc)) { 2122 printf("ti%d: chip initialization failed\n", sc->ti_unit); 2123 error = ENXIO; 2124 goto fail; 2125 } 2126 2127 /* 2128 * Get station address from the EEPROM. Note: the manual states 2129 * that the MAC address is at offset 0x8c, however the data is 2130 * stored as two longwords (since that's how it's loaded into 2131 * the NIC). This means the MAC address is actually preceded 2132 * by two zero bytes. We need to skip over those. 2133 */ 2134 if (ti_read_eeprom(sc, eaddr, 2135 TI_EE_MAC_OFFSET + 2, ETHER_ADDR_LEN)) { 2136 printf("ti%d: failed to read station address\n", unit); 2137 error = ENXIO; 2138 goto fail; 2139 } 2140 2141 /* Allocate the general information block and ring buffers. */ 2142 if (bus_dma_tag_create(NULL, /* parent */ 2143 1, 0, /* algnmnt, boundary */ 2144 BUS_SPACE_MAXADDR, /* lowaddr */ 2145 BUS_SPACE_MAXADDR, /* highaddr */ 2146 NULL, NULL, /* filter, filterarg */ 2147 BUS_SPACE_MAXSIZE_32BIT,/* maxsize */ 2148 0, /* nsegments */ 2149 BUS_SPACE_MAXSIZE_32BIT,/* maxsegsize */ 2150 0, /* flags */ 2151 NULL, NULL, /* lockfunc, lockarg */ 2152 &sc->ti_parent_dmat) != 0) { 2153 printf("ti%d: Failed to allocate parent dmat\n", sc->ti_unit); 2154 error = ENOMEM; 2155 goto fail; 2156 } 2157 2158 if (bus_dma_tag_create(sc->ti_parent_dmat, /* parent */ 2159 PAGE_SIZE, 0, /* algnmnt, boundary */ 2160 BUS_SPACE_MAXADDR_32BIT,/* lowaddr */ 2161 BUS_SPACE_MAXADDR, /* highaddr */ 2162 NULL, NULL, /* filter, filterarg */ 2163 sizeof(struct ti_ring_data), /* maxsize */ 2164 1, /* nsegments */ 2165 sizeof(struct ti_ring_data), /* maxsegsize */ 2166 0, /* flags */ 2167 NULL, NULL, /* lockfunc, lockarg */ 2168 &sc->ti_rdata_dmat) != 0) { 2169 printf("ti%d: Failed to allocate rdata dmat\n", sc->ti_unit); 2170 error = ENOMEM; 2171 goto fail; 2172 } 2173 2174 if (bus_dmamem_alloc(sc->ti_rdata_dmat, (void**)&sc->ti_rdata, 2175 BUS_DMA_NOWAIT, &sc->ti_rdata_dmamap) != 0) { 2176 printf("ti%d: Failed to allocate rdata memory\n", sc->ti_unit); 2177 error = ENOMEM; 2178 goto fail; 2179 } 2180 2181 if (bus_dmamap_load(sc->ti_rdata_dmat, sc->ti_rdata_dmamap, 2182 sc->ti_rdata, sizeof(struct ti_ring_data), 2183 ti_rdata_cb, sc, BUS_DMA_NOWAIT) != 0) { 2184 printf("ti%d: Failed to load rdata segments\n", sc->ti_unit); 2185 error = ENOMEM; 2186 goto fail; 2187 } 2188 2189 bzero(sc->ti_rdata, sizeof(struct ti_ring_data)); 2190 2191 /* Try to allocate memory for jumbo buffers. */ 2192#ifdef TI_PRIVATE_JUMBOS 2193 if (ti_alloc_jumbo_mem(sc)) { 2194 printf("ti%d: jumbo buffer allocation failed\n", sc->ti_unit); 2195 error = ENXIO; 2196 goto fail; 2197 } 2198#endif 2199 2200 /* 2201 * We really need a better way to tell a 1000baseTX card 2202 * from a 1000baseSX one, since in theory there could be 2203 * OEMed 1000baseTX cards from lame vendors who aren't 2204 * clever enough to change the PCI ID. For the moment 2205 * though, the AceNIC is the only copper card available. 2206 */ 2207 if (pci_get_vendor(dev) == ALT_VENDORID && 2208 pci_get_device(dev) == ALT_DEVICEID_ACENIC_COPPER) 2209 sc->ti_copper = 1; 2210 /* Ok, it's not the only copper card available. */ 2211 if (pci_get_vendor(dev) == NG_VENDORID && 2212 pci_get_device(dev) == NG_DEVICEID_GA620T) 2213 sc->ti_copper = 1; 2214 2215 /* Set default tuneable values. */ 2216 sc->ti_stat_ticks = 2 * TI_TICKS_PER_SEC; 2217#if 0 2218 sc->ti_rx_coal_ticks = TI_TICKS_PER_SEC / 5000; 2219#endif 2220 sc->ti_rx_coal_ticks = 170; 2221 sc->ti_tx_coal_ticks = TI_TICKS_PER_SEC / 500; 2222 sc->ti_rx_max_coal_bds = 64; 2223#if 0 2224 sc->ti_tx_max_coal_bds = 128; 2225#endif 2226 sc->ti_tx_max_coal_bds = 32; 2227 sc->ti_tx_buf_ratio = 21; 2228 2229 /* Set up ifnet structure */ 2230 ifp->if_softc = sc; 2231 if_initname(ifp, device_get_name(dev), device_get_unit(dev)); 2232 ifp->if_flags = IFF_BROADCAST | IFF_SIMPLEX | IFF_MULTICAST | 2233 IFF_NEEDSGIANT; 2234 tis[unit] = sc; 2235 ifp->if_ioctl = ti_ioctl; 2236 ifp->if_start = ti_start; 2237 ifp->if_watchdog = ti_watchdog; 2238 ifp->if_init = ti_init; 2239 ifp->if_mtu = ETHERMTU; 2240 ifp->if_snd.ifq_maxlen = TI_TX_RING_CNT - 1; 2241 2242 /* Set up ifmedia support. */ 2243 if (sc->ti_copper) { 2244 /* 2245 * Copper cards allow manual 10/100 mode selection, 2246 * but not manual 1000baseTX mode selection. Why? 2247 * Becuase currently there's no way to specify the 2248 * master/slave setting through the firmware interface, 2249 * so Alteon decided to just bag it and handle it 2250 * via autonegotiation. 2251 */ 2252 ifmedia_add(&sc->ifmedia, IFM_ETHER|IFM_10_T, 0, NULL); 2253 ifmedia_add(&sc->ifmedia, 2254 IFM_ETHER|IFM_10_T|IFM_FDX, 0, NULL); 2255 ifmedia_add(&sc->ifmedia, IFM_ETHER|IFM_100_TX, 0, NULL); 2256 ifmedia_add(&sc->ifmedia, 2257 IFM_ETHER|IFM_100_TX|IFM_FDX, 0, NULL); 2258 ifmedia_add(&sc->ifmedia, IFM_ETHER|IFM_1000_T, 0, NULL); 2259 ifmedia_add(&sc->ifmedia, 2260 IFM_ETHER|IFM_1000_T|IFM_FDX, 0, NULL); 2261 } else { 2262 /* Fiber cards don't support 10/100 modes. */ 2263 ifmedia_add(&sc->ifmedia, IFM_ETHER|IFM_1000_SX, 0, NULL); 2264 ifmedia_add(&sc->ifmedia, 2265 IFM_ETHER|IFM_1000_SX|IFM_FDX, 0, NULL); 2266 } 2267 ifmedia_add(&sc->ifmedia, IFM_ETHER|IFM_AUTO, 0, NULL); 2268 ifmedia_set(&sc->ifmedia, IFM_ETHER|IFM_AUTO); 2269 2270 /* 2271 * We're assuming here that card initialization is a sequential 2272 * thing. If it isn't, multiple cards probing at the same time 2273 * could stomp on the list of softcs here. 2274 */ 2275 2276 /* Register the device */ 2277 sc->dev = make_dev(&ti_cdevsw, sc->ti_unit, UID_ROOT, GID_OPERATOR, 2278 0600, "ti%d", sc->ti_unit); 2279 sc->dev->si_drv1 = sc; 2280 2281 /* 2282 * Call MI attach routine. 2283 */ 2284 ether_ifattach(ifp, eaddr); 2285 2286 /* Hook interrupt last to avoid having to lock softc */ 2287 error = bus_setup_intr(dev, sc->ti_irq, INTR_TYPE_NET, 2288 ti_intr, sc, &sc->ti_intrhand); 2289 2290 if (error) { 2291 printf("ti%d: couldn't set up irq\n", unit); 2292 ether_ifdetach(ifp); 2293 if_free(ifp); 2294 goto fail; 2295 } 2296 2297fail: 2298 if (sc && error) 2299 ti_detach(dev); 2300 2301 return (error); 2302} 2303 2304/* 2305 * Shutdown hardware and free up resources. This can be called any 2306 * time after the mutex has been initialized. It is called in both 2307 * the error case in attach and the normal detach case so it needs 2308 * to be careful about only freeing resources that have actually been 2309 * allocated. 2310 */ 2311static int 2312ti_detach(dev) 2313 device_t dev; 2314{ 2315 struct ti_softc *sc; 2316 struct ifnet *ifp; 2317 2318 sc = device_get_softc(dev); 2319 if (sc->dev) 2320 destroy_dev(sc->dev); 2321 KASSERT(mtx_initialized(&sc->ti_mtx), ("ti mutex not initialized")); 2322 TI_LOCK(sc); 2323 ifp = sc->ti_ifp; 2324 2325 /* These should only be active if attach succeeded */ 2326 if (device_is_attached(dev)) { 2327 ti_stop(sc); 2328 ether_ifdetach(ifp); 2329 if_free(ifp); 2330 bus_generic_detach(dev); 2331 } 2332 ifmedia_removeall(&sc->ifmedia); 2333 2334 if (sc->ti_rdata) 2335 bus_dmamem_free(sc->ti_rdata_dmat, sc->ti_rdata, 2336 sc->ti_rdata_dmamap); 2337 if (sc->ti_rdata_dmat) 2338 bus_dma_tag_destroy(sc->ti_rdata_dmat); 2339 if (sc->ti_parent_dmat) 2340 bus_dma_tag_destroy(sc->ti_parent_dmat); 2341 if (sc->ti_intrhand) 2342 bus_teardown_intr(dev, sc->ti_irq, sc->ti_intrhand); 2343 if (sc->ti_irq) 2344 bus_release_resource(dev, SYS_RES_IRQ, 0, sc->ti_irq); 2345 if (sc->ti_res) { 2346 bus_release_resource(dev, SYS_RES_MEMORY, TI_PCI_LOMEM, 2347 sc->ti_res); 2348 } 2349 2350#ifdef TI_PRIVATE_JUMBOS 2351 if (sc->ti_cdata.ti_jumbo_buf) 2352 contigfree(sc->ti_cdata.ti_jumbo_buf, TI_JMEM, M_DEVBUF); 2353#endif 2354 if (sc->ti_rdata) 2355 contigfree(sc->ti_rdata, sizeof(struct ti_ring_data), M_DEVBUF); 2356 2357 TI_UNLOCK(sc); 2358 mtx_destroy(&sc->ti_mtx); 2359 2360 return (0); 2361} 2362 2363#ifdef TI_JUMBO_HDRSPLIT 2364/* 2365 * If hdr_len is 0, that means that header splitting wasn't done on 2366 * this packet for some reason. The two most likely reasons are that 2367 * the protocol isn't a supported protocol for splitting, or this 2368 * packet had a fragment offset that wasn't 0. 2369 * 2370 * The header length, if it is non-zero, will always be the length of 2371 * the headers on the packet, but that length could be longer than the 2372 * first mbuf. So we take the minimum of the two as the actual 2373 * length. 2374 */ 2375static __inline void 2376ti_hdr_split(struct mbuf *top, int hdr_len, int pkt_len, int idx) 2377{ 2378 int i = 0; 2379 int lengths[4] = {0, 0, 0, 0}; 2380 struct mbuf *m, *mp; 2381 2382 if (hdr_len != 0) 2383 top->m_len = min(hdr_len, top->m_len); 2384 pkt_len -= top->m_len; 2385 lengths[i++] = top->m_len; 2386 2387 mp = top; 2388 for (m = top->m_next; m && pkt_len; m = m->m_next) { 2389 m->m_len = m->m_ext.ext_size = min(m->m_len, pkt_len); 2390 pkt_len -= m->m_len; 2391 lengths[i++] = m->m_len; 2392 mp = m; 2393 } 2394 2395#if 0 2396 if (hdr_len != 0) 2397 printf("got split packet: "); 2398 else 2399 printf("got non-split packet: "); 2400 2401 printf("%d,%d,%d,%d = %d\n", lengths[0], 2402 lengths[1], lengths[2], lengths[3], 2403 lengths[0] + lengths[1] + lengths[2] + 2404 lengths[3]); 2405#endif 2406 2407 if (pkt_len) 2408 panic("header splitting didn't"); 2409 2410 if (m) { 2411 m_freem(m); 2412 mp->m_next = NULL; 2413 2414 } 2415 if (mp->m_next != NULL) 2416 panic("ti_hdr_split: last mbuf in chain should be null"); 2417} 2418#endif /* TI_JUMBO_HDRSPLIT */ 2419 2420/* 2421 * Frame reception handling. This is called if there's a frame 2422 * on the receive return list. 2423 * 2424 * Note: we have to be able to handle three possibilities here: 2425 * 1) the frame is from the mini receive ring (can only happen) 2426 * on Tigon 2 boards) 2427 * 2) the frame is from the jumbo recieve ring 2428 * 3) the frame is from the standard receive ring 2429 */ 2430 2431static void 2432ti_rxeof(sc) 2433 struct ti_softc *sc; 2434{ 2435 struct ifnet *ifp; 2436 struct ti_cmd_desc cmd; 2437 2438 TI_LOCK_ASSERT(sc); 2439 2440 ifp = sc->ti_ifp; 2441 2442 while (sc->ti_rx_saved_considx != sc->ti_return_prodidx.ti_idx) { 2443 struct ti_rx_desc *cur_rx; 2444 u_int32_t rxidx; 2445 struct mbuf *m = NULL; 2446 u_int16_t vlan_tag = 0; 2447 int have_tag = 0; 2448 2449 cur_rx = 2450 &sc->ti_rdata->ti_rx_return_ring[sc->ti_rx_saved_considx]; 2451 rxidx = cur_rx->ti_idx; 2452 TI_INC(sc->ti_rx_saved_considx, TI_RETURN_RING_CNT); 2453 2454 if (cur_rx->ti_flags & TI_BDFLAG_VLAN_TAG) { 2455 have_tag = 1; 2456 vlan_tag = cur_rx->ti_vlan_tag & 0xfff; 2457 } 2458 2459 if (cur_rx->ti_flags & TI_BDFLAG_JUMBO_RING) { 2460 2461 TI_INC(sc->ti_jumbo, TI_JUMBO_RX_RING_CNT); 2462 m = sc->ti_cdata.ti_rx_jumbo_chain[rxidx]; 2463 sc->ti_cdata.ti_rx_jumbo_chain[rxidx] = NULL; 2464 if (cur_rx->ti_flags & TI_BDFLAG_ERROR) { 2465 ifp->if_ierrors++; 2466 ti_newbuf_jumbo(sc, sc->ti_jumbo, m); 2467 continue; 2468 } 2469 if (ti_newbuf_jumbo(sc, sc->ti_jumbo, NULL) == ENOBUFS) { 2470 ifp->if_ierrors++; 2471 ti_newbuf_jumbo(sc, sc->ti_jumbo, m); 2472 continue; 2473 } 2474#ifdef TI_PRIVATE_JUMBOS 2475 m->m_len = cur_rx->ti_len; 2476#else /* TI_PRIVATE_JUMBOS */ 2477#ifdef TI_JUMBO_HDRSPLIT 2478 if (sc->ti_hdrsplit) 2479 ti_hdr_split(m, TI_HOSTADDR(cur_rx->ti_addr), 2480 cur_rx->ti_len, rxidx); 2481 else 2482#endif /* TI_JUMBO_HDRSPLIT */ 2483 m_adj(m, cur_rx->ti_len - m->m_pkthdr.len); 2484#endif /* TI_PRIVATE_JUMBOS */ 2485 } else if (cur_rx->ti_flags & TI_BDFLAG_MINI_RING) { 2486 TI_INC(sc->ti_mini, TI_MINI_RX_RING_CNT); 2487 m = sc->ti_cdata.ti_rx_mini_chain[rxidx]; 2488 sc->ti_cdata.ti_rx_mini_chain[rxidx] = NULL; 2489 if (cur_rx->ti_flags & TI_BDFLAG_ERROR) { 2490 ifp->if_ierrors++; 2491 ti_newbuf_mini(sc, sc->ti_mini, m); 2492 continue; 2493 } 2494 if (ti_newbuf_mini(sc, sc->ti_mini, NULL) == ENOBUFS) { 2495 ifp->if_ierrors++; 2496 ti_newbuf_mini(sc, sc->ti_mini, m); 2497 continue; 2498 } 2499 m->m_len = cur_rx->ti_len; 2500 } else { 2501 TI_INC(sc->ti_std, TI_STD_RX_RING_CNT); 2502 m = sc->ti_cdata.ti_rx_std_chain[rxidx]; 2503 sc->ti_cdata.ti_rx_std_chain[rxidx] = NULL; 2504 if (cur_rx->ti_flags & TI_BDFLAG_ERROR) { 2505 ifp->if_ierrors++; 2506 ti_newbuf_std(sc, sc->ti_std, m); 2507 continue; 2508 } 2509 if (ti_newbuf_std(sc, sc->ti_std, NULL) == ENOBUFS) { 2510 ifp->if_ierrors++; 2511 ti_newbuf_std(sc, sc->ti_std, m); 2512 continue; 2513 } 2514 m->m_len = cur_rx->ti_len; 2515 } 2516 2517 m->m_pkthdr.len = cur_rx->ti_len; 2518 ifp->if_ipackets++; 2519 m->m_pkthdr.rcvif = ifp; 2520 2521 if (ifp->if_hwassist) { 2522 m->m_pkthdr.csum_flags |= CSUM_IP_CHECKED | 2523 CSUM_DATA_VALID; 2524 if ((cur_rx->ti_ip_cksum ^ 0xffff) == 0) 2525 m->m_pkthdr.csum_flags |= CSUM_IP_VALID; 2526 m->m_pkthdr.csum_data = cur_rx->ti_tcp_udp_cksum; 2527 } 2528 2529 /* 2530 * If we received a packet with a vlan tag, 2531 * tag it before passing the packet upward. 2532 */ 2533 if (have_tag) 2534 VLAN_INPUT_TAG(ifp, m, vlan_tag, continue); 2535 TI_UNLOCK(sc); 2536 (*ifp->if_input)(ifp, m); 2537 TI_LOCK(sc); 2538 } 2539 2540 /* Only necessary on the Tigon 1. */ 2541 if (sc->ti_hwrev == TI_HWREV_TIGON) 2542 CSR_WRITE_4(sc, TI_GCR_RXRETURNCONS_IDX, 2543 sc->ti_rx_saved_considx); 2544 2545 TI_UPDATE_STDPROD(sc, sc->ti_std); 2546 TI_UPDATE_MINIPROD(sc, sc->ti_mini); 2547 TI_UPDATE_JUMBOPROD(sc, sc->ti_jumbo); 2548} 2549 2550static void 2551ti_txeof(sc) 2552 struct ti_softc *sc; 2553{ 2554 struct ti_tx_desc *cur_tx = NULL; 2555 struct ifnet *ifp; 2556 2557 ifp = sc->ti_ifp; 2558 2559 /* 2560 * Go through our tx ring and free mbufs for those 2561 * frames that have been sent. 2562 */ 2563 while (sc->ti_tx_saved_considx != sc->ti_tx_considx.ti_idx) { 2564 u_int32_t idx = 0; 2565 2566 idx = sc->ti_tx_saved_considx; 2567 if (sc->ti_hwrev == TI_HWREV_TIGON) { 2568 if (idx > 383) 2569 CSR_WRITE_4(sc, TI_WINBASE, 2570 TI_TX_RING_BASE + 6144); 2571 else if (idx > 255) 2572 CSR_WRITE_4(sc, TI_WINBASE, 2573 TI_TX_RING_BASE + 4096); 2574 else if (idx > 127) 2575 CSR_WRITE_4(sc, TI_WINBASE, 2576 TI_TX_RING_BASE + 2048); 2577 else 2578 CSR_WRITE_4(sc, TI_WINBASE, 2579 TI_TX_RING_BASE); 2580 cur_tx = &sc->ti_rdata->ti_tx_ring_nic[idx % 128]; 2581 } else 2582 cur_tx = &sc->ti_rdata->ti_tx_ring[idx]; 2583 if (cur_tx->ti_flags & TI_BDFLAG_END) 2584 ifp->if_opackets++; 2585 if (sc->ti_cdata.ti_tx_chain[idx] != NULL) { 2586 m_freem(sc->ti_cdata.ti_tx_chain[idx]); 2587 sc->ti_cdata.ti_tx_chain[idx] = NULL; 2588 } 2589 sc->ti_txcnt--; 2590 TI_INC(sc->ti_tx_saved_considx, TI_TX_RING_CNT); 2591 ifp->if_timer = 0; 2592 } 2593 2594 if (cur_tx != NULL) 2595 ifp->if_flags &= ~IFF_OACTIVE; 2596} 2597 2598static void 2599ti_intr(xsc) 2600 void *xsc; 2601{ 2602 struct ti_softc *sc; 2603 struct ifnet *ifp; 2604 2605 sc = xsc; 2606 TI_LOCK(sc); 2607 ifp = sc->ti_ifp; 2608 2609/*#ifdef notdef*/ 2610 /* Avoid this for now -- checking this register is expensive. */ 2611 /* Make sure this is really our interrupt. */ 2612 if (!(CSR_READ_4(sc, TI_MISC_HOST_CTL) & TI_MHC_INTSTATE)) { 2613 TI_UNLOCK(sc); 2614 return; 2615 } 2616/*#endif*/ 2617 2618 /* Ack interrupt and stop others from occuring. */ 2619 CSR_WRITE_4(sc, TI_MB_HOSTINTR, 1); 2620 2621 if (ifp->if_flags & IFF_RUNNING) { 2622 /* Check RX return ring producer/consumer */ 2623 ti_rxeof(sc); 2624 2625 /* Check TX ring producer/consumer */ 2626 ti_txeof(sc); 2627 } 2628 2629 ti_handle_events(sc); 2630 2631 /* Re-enable interrupts. */ 2632 CSR_WRITE_4(sc, TI_MB_HOSTINTR, 0); 2633 2634 if (ifp->if_flags & IFF_RUNNING && ifp->if_snd.ifq_head != NULL) 2635 ti_start(ifp); 2636 2637 TI_UNLOCK(sc); 2638} 2639 2640static void 2641ti_stats_update(sc) 2642 struct ti_softc *sc; 2643{ 2644 struct ifnet *ifp; 2645 2646 ifp = sc->ti_ifp; 2647 2648 ifp->if_collisions += 2649 (sc->ti_rdata->ti_info.ti_stats.dot3StatsSingleCollisionFrames + 2650 sc->ti_rdata->ti_info.ti_stats.dot3StatsMultipleCollisionFrames + 2651 sc->ti_rdata->ti_info.ti_stats.dot3StatsExcessiveCollisions + 2652 sc->ti_rdata->ti_info.ti_stats.dot3StatsLateCollisions) - 2653 ifp->if_collisions; 2654} 2655 2656/* 2657 * Encapsulate an mbuf chain in the tx ring by coupling the mbuf data 2658 * pointers to descriptors. 2659 */ 2660static int 2661ti_encap(sc, m_head, txidx) 2662 struct ti_softc *sc; 2663 struct mbuf *m_head; 2664 u_int32_t *txidx; 2665{ 2666 struct ti_tx_desc *f = NULL; 2667 struct mbuf *m; 2668 u_int32_t frag, cur, cnt = 0; 2669 u_int16_t csum_flags = 0; 2670 struct m_tag *mtag; 2671 2672 m = m_head; 2673 cur = frag = *txidx; 2674 2675 if (m_head->m_pkthdr.csum_flags) { 2676 if (m_head->m_pkthdr.csum_flags & CSUM_IP) 2677 csum_flags |= TI_BDFLAG_IP_CKSUM; 2678 if (m_head->m_pkthdr.csum_flags & (CSUM_TCP | CSUM_UDP)) 2679 csum_flags |= TI_BDFLAG_TCP_UDP_CKSUM; 2680 if (m_head->m_flags & M_LASTFRAG) 2681 csum_flags |= TI_BDFLAG_IP_FRAG_END; 2682 else if (m_head->m_flags & M_FRAG) 2683 csum_flags |= TI_BDFLAG_IP_FRAG; 2684 } 2685 2686 mtag = VLAN_OUTPUT_TAG(sc->ti_ifp, m); 2687 2688 /* 2689 * Start packing the mbufs in this chain into 2690 * the fragment pointers. Stop when we run out 2691 * of fragments or hit the end of the mbuf chain. 2692 */ 2693 for (m = m_head; m != NULL; m = m->m_next) { 2694 if (m->m_len != 0) { 2695 if (sc->ti_hwrev == TI_HWREV_TIGON) { 2696 if (frag > 383) 2697 CSR_WRITE_4(sc, TI_WINBASE, 2698 TI_TX_RING_BASE + 6144); 2699 else if (frag > 255) 2700 CSR_WRITE_4(sc, TI_WINBASE, 2701 TI_TX_RING_BASE + 4096); 2702 else if (frag > 127) 2703 CSR_WRITE_4(sc, TI_WINBASE, 2704 TI_TX_RING_BASE + 2048); 2705 else 2706 CSR_WRITE_4(sc, TI_WINBASE, 2707 TI_TX_RING_BASE); 2708 f = &sc->ti_rdata->ti_tx_ring_nic[frag % 128]; 2709 } else 2710 f = &sc->ti_rdata->ti_tx_ring[frag]; 2711 if (sc->ti_cdata.ti_tx_chain[frag] != NULL) 2712 break; 2713 TI_HOSTADDR(f->ti_addr) = vtophys(mtod(m, vm_offset_t)); 2714 f->ti_len = m->m_len; 2715 f->ti_flags = csum_flags; 2716 2717 if (mtag != NULL) { 2718 f->ti_flags |= TI_BDFLAG_VLAN_TAG; 2719 f->ti_vlan_tag = VLAN_TAG_VALUE(mtag) & 0xfff; 2720 } else { 2721 f->ti_vlan_tag = 0; 2722 } 2723 2724 /* 2725 * Sanity check: avoid coming within 16 descriptors 2726 * of the end of the ring. 2727 */ 2728 if ((TI_TX_RING_CNT - (sc->ti_txcnt + cnt)) < 16) 2729 return (ENOBUFS); 2730 cur = frag; 2731 TI_INC(frag, TI_TX_RING_CNT); 2732 cnt++; 2733 } 2734 } 2735 2736 if (m != NULL) 2737 return (ENOBUFS); 2738 2739 if (frag == sc->ti_tx_saved_considx) 2740 return (ENOBUFS); 2741 2742 if (sc->ti_hwrev == TI_HWREV_TIGON) 2743 sc->ti_rdata->ti_tx_ring_nic[cur % 128].ti_flags |= 2744 TI_BDFLAG_END; 2745 else 2746 sc->ti_rdata->ti_tx_ring[cur].ti_flags |= TI_BDFLAG_END; 2747 sc->ti_cdata.ti_tx_chain[cur] = m_head; 2748 sc->ti_txcnt += cnt; 2749 2750 *txidx = frag; 2751 2752 return (0); 2753} 2754 2755/* 2756 * Main transmit routine. To avoid having to do mbuf copies, we put pointers 2757 * to the mbuf data regions directly in the transmit descriptors. 2758 */ 2759static void 2760ti_start(ifp) 2761 struct ifnet *ifp; 2762{ 2763 struct ti_softc *sc; 2764 struct mbuf *m_head = NULL; 2765 u_int32_t prodidx = 0; 2766 2767 sc = ifp->if_softc; 2768 TI_LOCK(sc); 2769 2770 prodidx = CSR_READ_4(sc, TI_MB_SENDPROD_IDX); 2771 2772 while (sc->ti_cdata.ti_tx_chain[prodidx] == NULL) { 2773 IF_DEQUEUE(&ifp->if_snd, m_head); 2774 if (m_head == NULL) 2775 break; 2776 2777 /* 2778 * XXX 2779 * safety overkill. If this is a fragmented packet chain 2780 * with delayed TCP/UDP checksums, then only encapsulate 2781 * it if we have enough descriptors to handle the entire 2782 * chain at once. 2783 * (paranoia -- may not actually be needed) 2784 */ 2785 if (m_head->m_flags & M_FIRSTFRAG && 2786 m_head->m_pkthdr.csum_flags & (CSUM_DELAY_DATA)) { 2787 if ((TI_TX_RING_CNT - sc->ti_txcnt) < 2788 m_head->m_pkthdr.csum_data + 16) { 2789 IF_PREPEND(&ifp->if_snd, m_head); 2790 ifp->if_flags |= IFF_OACTIVE; 2791 break; 2792 } 2793 } 2794 2795 /* 2796 * Pack the data into the transmit ring. If we 2797 * don't have room, set the OACTIVE flag and wait 2798 * for the NIC to drain the ring. 2799 */ 2800 if (ti_encap(sc, m_head, &prodidx)) { 2801 IF_PREPEND(&ifp->if_snd, m_head); 2802 ifp->if_flags |= IFF_OACTIVE; 2803 break; 2804 } 2805 2806 /* 2807 * If there's a BPF listener, bounce a copy of this frame 2808 * to him. 2809 */ 2810 BPF_MTAP(ifp, m_head); 2811 } 2812 2813 /* Transmit */ 2814 CSR_WRITE_4(sc, TI_MB_SENDPROD_IDX, prodidx); 2815 2816 /* 2817 * Set a timeout in case the chip goes out to lunch. 2818 */ 2819 ifp->if_timer = 5; 2820 TI_UNLOCK(sc); 2821} 2822 2823static void 2824ti_init(xsc) 2825 void *xsc; 2826{ 2827 struct ti_softc *sc = xsc; 2828 2829 /* Cancel pending I/O and flush buffers. */ 2830 ti_stop(sc); 2831 2832 TI_LOCK(sc); 2833 /* Init the gen info block, ring control blocks and firmware. */ 2834 if (ti_gibinit(sc)) { 2835 printf("ti%d: initialization failure\n", sc->ti_unit); 2836 TI_UNLOCK(sc); 2837 return; 2838 } 2839 2840 TI_UNLOCK(sc); 2841} 2842 2843static void ti_init2(sc) 2844 struct ti_softc *sc; 2845{ 2846 struct ti_cmd_desc cmd; 2847 struct ifnet *ifp; 2848 u_int16_t *m; 2849 struct ifmedia *ifm; 2850 int tmp; 2851 2852 ifp = sc->ti_ifp; 2853 2854 /* Specify MTU and interface index. */ 2855 CSR_WRITE_4(sc, TI_GCR_IFINDEX, sc->ti_unit); 2856 CSR_WRITE_4(sc, TI_GCR_IFMTU, ifp->if_mtu + 2857 ETHER_HDR_LEN + ETHER_CRC_LEN + ETHER_VLAN_ENCAP_LEN); 2858 TI_DO_CMD(TI_CMD_UPDATE_GENCOM, 0, 0); 2859 2860 /* Load our MAC address. */ 2861 m = (u_int16_t *)&IFP2ENADDR(sc->ti_ifp)[0]; 2862 CSR_WRITE_4(sc, TI_GCR_PAR0, htons(m[0])); 2863 CSR_WRITE_4(sc, TI_GCR_PAR1, (htons(m[1]) << 16) | htons(m[2])); 2864 TI_DO_CMD(TI_CMD_SET_MAC_ADDR, 0, 0); 2865 2866 /* Enable or disable promiscuous mode as needed. */ 2867 if (ifp->if_flags & IFF_PROMISC) { 2868 TI_DO_CMD(TI_CMD_SET_PROMISC_MODE, TI_CMD_CODE_PROMISC_ENB, 0); 2869 } else { 2870 TI_DO_CMD(TI_CMD_SET_PROMISC_MODE, TI_CMD_CODE_PROMISC_DIS, 0); 2871 } 2872 2873 /* Program multicast filter. */ 2874 ti_setmulti(sc); 2875 2876 /* 2877 * If this is a Tigon 1, we should tell the 2878 * firmware to use software packet filtering. 2879 */ 2880 if (sc->ti_hwrev == TI_HWREV_TIGON) { 2881 TI_DO_CMD(TI_CMD_FDR_FILTERING, TI_CMD_CODE_FILT_ENB, 0); 2882 } 2883 2884 /* Init RX ring. */ 2885 ti_init_rx_ring_std(sc); 2886 2887 /* Init jumbo RX ring. */ 2888 if (ifp->if_mtu > (ETHERMTU + ETHER_HDR_LEN + ETHER_CRC_LEN)) 2889 ti_init_rx_ring_jumbo(sc); 2890 2891 /* 2892 * If this is a Tigon 2, we can also configure the 2893 * mini ring. 2894 */ 2895 if (sc->ti_hwrev == TI_HWREV_TIGON_II) 2896 ti_init_rx_ring_mini(sc); 2897 2898 CSR_WRITE_4(sc, TI_GCR_RXRETURNCONS_IDX, 0); 2899 sc->ti_rx_saved_considx = 0; 2900 2901 /* Init TX ring. */ 2902 ti_init_tx_ring(sc); 2903 2904 /* Tell firmware we're alive. */ 2905 TI_DO_CMD(TI_CMD_HOST_STATE, TI_CMD_CODE_STACK_UP, 0); 2906 2907 /* Enable host interrupts. */ 2908 CSR_WRITE_4(sc, TI_MB_HOSTINTR, 0); 2909 2910 ifp->if_flags |= IFF_RUNNING; 2911 ifp->if_flags &= ~IFF_OACTIVE; 2912 2913 /* 2914 * Make sure to set media properly. We have to do this 2915 * here since we have to issue commands in order to set 2916 * the link negotiation and we can't issue commands until 2917 * the firmware is running. 2918 */ 2919 ifm = &sc->ifmedia; 2920 tmp = ifm->ifm_media; 2921 ifm->ifm_media = ifm->ifm_cur->ifm_media; 2922 ti_ifmedia_upd(ifp); 2923 ifm->ifm_media = tmp; 2924} 2925 2926/* 2927 * Set media options. 2928 */ 2929static int 2930ti_ifmedia_upd(ifp) 2931 struct ifnet *ifp; 2932{ 2933 struct ti_softc *sc; 2934 struct ifmedia *ifm; 2935 struct ti_cmd_desc cmd; 2936 u_int32_t flowctl; 2937 2938 sc = ifp->if_softc; 2939 ifm = &sc->ifmedia; 2940 2941 if (IFM_TYPE(ifm->ifm_media) != IFM_ETHER) 2942 return (EINVAL); 2943 2944 flowctl = 0; 2945 2946 switch (IFM_SUBTYPE(ifm->ifm_media)) { 2947 case IFM_AUTO: 2948 /* 2949 * Transmit flow control doesn't work on the Tigon 1. 2950 */ 2951 flowctl = TI_GLNK_RX_FLOWCTL_Y; 2952 2953 /* 2954 * Transmit flow control can also cause problems on the 2955 * Tigon 2, apparantly with both the copper and fiber 2956 * boards. The symptom is that the interface will just 2957 * hang. This was reproduced with Alteon 180 switches. 2958 */ 2959#if 0 2960 if (sc->ti_hwrev != TI_HWREV_TIGON) 2961 flowctl |= TI_GLNK_TX_FLOWCTL_Y; 2962#endif 2963 2964 CSR_WRITE_4(sc, TI_GCR_GLINK, TI_GLNK_PREF|TI_GLNK_1000MB| 2965 TI_GLNK_FULL_DUPLEX| flowctl | 2966 TI_GLNK_AUTONEGENB|TI_GLNK_ENB); 2967 2968 flowctl = TI_LNK_RX_FLOWCTL_Y; 2969#if 0 2970 if (sc->ti_hwrev != TI_HWREV_TIGON) 2971 flowctl |= TI_LNK_TX_FLOWCTL_Y; 2972#endif 2973 2974 CSR_WRITE_4(sc, TI_GCR_LINK, TI_LNK_100MB|TI_LNK_10MB| 2975 TI_LNK_FULL_DUPLEX|TI_LNK_HALF_DUPLEX| flowctl | 2976 TI_LNK_AUTONEGENB|TI_LNK_ENB); 2977 TI_DO_CMD(TI_CMD_LINK_NEGOTIATION, 2978 TI_CMD_CODE_NEGOTIATE_BOTH, 0); 2979 break; 2980 case IFM_1000_SX: 2981 case IFM_1000_T: 2982 flowctl = TI_GLNK_RX_FLOWCTL_Y; 2983#if 0 2984 if (sc->ti_hwrev != TI_HWREV_TIGON) 2985 flowctl |= TI_GLNK_TX_FLOWCTL_Y; 2986#endif 2987 2988 CSR_WRITE_4(sc, TI_GCR_GLINK, TI_GLNK_PREF|TI_GLNK_1000MB| 2989 flowctl |TI_GLNK_ENB); 2990 CSR_WRITE_4(sc, TI_GCR_LINK, 0); 2991 if ((ifm->ifm_media & IFM_GMASK) == IFM_FDX) { 2992 TI_SETBIT(sc, TI_GCR_GLINK, TI_GLNK_FULL_DUPLEX); 2993 } 2994 TI_DO_CMD(TI_CMD_LINK_NEGOTIATION, 2995 TI_CMD_CODE_NEGOTIATE_GIGABIT, 0); 2996 break; 2997 case IFM_100_FX: 2998 case IFM_10_FL: 2999 case IFM_100_TX: 3000 case IFM_10_T: 3001 flowctl = TI_LNK_RX_FLOWCTL_Y; 3002#if 0 3003 if (sc->ti_hwrev != TI_HWREV_TIGON) 3004 flowctl |= TI_LNK_TX_FLOWCTL_Y; 3005#endif 3006 3007 CSR_WRITE_4(sc, TI_GCR_GLINK, 0); 3008 CSR_WRITE_4(sc, TI_GCR_LINK, TI_LNK_ENB|TI_LNK_PREF|flowctl); 3009 if (IFM_SUBTYPE(ifm->ifm_media) == IFM_100_FX || 3010 IFM_SUBTYPE(ifm->ifm_media) == IFM_100_TX) { 3011 TI_SETBIT(sc, TI_GCR_LINK, TI_LNK_100MB); 3012 } else { 3013 TI_SETBIT(sc, TI_GCR_LINK, TI_LNK_10MB); 3014 } 3015 if ((ifm->ifm_media & IFM_GMASK) == IFM_FDX) { 3016 TI_SETBIT(sc, TI_GCR_LINK, TI_LNK_FULL_DUPLEX); 3017 } else { 3018 TI_SETBIT(sc, TI_GCR_LINK, TI_LNK_HALF_DUPLEX); 3019 } 3020 TI_DO_CMD(TI_CMD_LINK_NEGOTIATION, 3021 TI_CMD_CODE_NEGOTIATE_10_100, 0); 3022 break; 3023 } 3024 3025 return (0); 3026} 3027 3028/* 3029 * Report current media status. 3030 */ 3031static void 3032ti_ifmedia_sts(ifp, ifmr) 3033 struct ifnet *ifp; 3034 struct ifmediareq *ifmr; 3035{ 3036 struct ti_softc *sc; 3037 u_int32_t media = 0; 3038 3039 sc = ifp->if_softc; 3040 3041 ifmr->ifm_status = IFM_AVALID; 3042 ifmr->ifm_active = IFM_ETHER; 3043 3044 if (sc->ti_linkstat == TI_EV_CODE_LINK_DOWN) 3045 return; 3046 3047 ifmr->ifm_status |= IFM_ACTIVE; 3048 3049 if (sc->ti_linkstat == TI_EV_CODE_GIG_LINK_UP) { 3050 media = CSR_READ_4(sc, TI_GCR_GLINK_STAT); 3051 if (sc->ti_copper) 3052 ifmr->ifm_active |= IFM_1000_T; 3053 else 3054 ifmr->ifm_active |= IFM_1000_SX; 3055 if (media & TI_GLNK_FULL_DUPLEX) 3056 ifmr->ifm_active |= IFM_FDX; 3057 else 3058 ifmr->ifm_active |= IFM_HDX; 3059 } else if (sc->ti_linkstat == TI_EV_CODE_LINK_UP) { 3060 media = CSR_READ_4(sc, TI_GCR_LINK_STAT); 3061 if (sc->ti_copper) { 3062 if (media & TI_LNK_100MB) 3063 ifmr->ifm_active |= IFM_100_TX; 3064 if (media & TI_LNK_10MB) 3065 ifmr->ifm_active |= IFM_10_T; 3066 } else { 3067 if (media & TI_LNK_100MB) 3068 ifmr->ifm_active |= IFM_100_FX; 3069 if (media & TI_LNK_10MB) 3070 ifmr->ifm_active |= IFM_10_FL; 3071 } 3072 if (media & TI_LNK_FULL_DUPLEX) 3073 ifmr->ifm_active |= IFM_FDX; 3074 if (media & TI_LNK_HALF_DUPLEX) 3075 ifmr->ifm_active |= IFM_HDX; 3076 } 3077} 3078 3079static int 3080ti_ioctl(ifp, command, data) 3081 struct ifnet *ifp; 3082 u_long command; 3083 caddr_t data; 3084{ 3085 struct ti_softc *sc = ifp->if_softc; 3086 struct ifreq *ifr = (struct ifreq *) data; 3087 int mask, error = 0; 3088 struct ti_cmd_desc cmd; 3089 3090 TI_LOCK(sc); 3091 3092 switch (command) { 3093 case SIOCSIFMTU: 3094 if (ifr->ifr_mtu > TI_JUMBO_MTU) 3095 error = EINVAL; 3096 else { 3097 ifp->if_mtu = ifr->ifr_mtu; 3098 ti_init(sc); 3099 } 3100 break; 3101 case SIOCSIFFLAGS: 3102 if (ifp->if_flags & IFF_UP) { 3103 /* 3104 * If only the state of the PROMISC flag changed, 3105 * then just use the 'set promisc mode' command 3106 * instead of reinitializing the entire NIC. Doing 3107 * a full re-init means reloading the firmware and 3108 * waiting for it to start up, which may take a 3109 * second or two. 3110 */ 3111 if (ifp->if_flags & IFF_RUNNING && 3112 ifp->if_flags & IFF_PROMISC && 3113 !(sc->ti_if_flags & IFF_PROMISC)) { 3114 TI_DO_CMD(TI_CMD_SET_PROMISC_MODE, 3115 TI_CMD_CODE_PROMISC_ENB, 0); 3116 } else if (ifp->if_flags & IFF_RUNNING && 3117 !(ifp->if_flags & IFF_PROMISC) && 3118 sc->ti_if_flags & IFF_PROMISC) { 3119 TI_DO_CMD(TI_CMD_SET_PROMISC_MODE, 3120 TI_CMD_CODE_PROMISC_DIS, 0); 3121 } else 3122 ti_init(sc); 3123 } else { 3124 if (ifp->if_flags & IFF_RUNNING) { 3125 ti_stop(sc); 3126 } 3127 } 3128 sc->ti_if_flags = ifp->if_flags; 3129 error = 0; 3130 break; 3131 case SIOCADDMULTI: 3132 case SIOCDELMULTI: 3133 if (ifp->if_flags & IFF_RUNNING) { 3134 ti_setmulti(sc); 3135 error = 0; 3136 } 3137 break; 3138 case SIOCSIFMEDIA: 3139 case SIOCGIFMEDIA: 3140 error = ifmedia_ioctl(ifp, ifr, &sc->ifmedia, command); 3141 break; 3142 case SIOCSIFCAP: 3143 mask = ifr->ifr_reqcap ^ ifp->if_capenable; 3144 if (mask & IFCAP_HWCSUM) { 3145 if (IFCAP_HWCSUM & ifp->if_capenable) 3146 ifp->if_capenable &= ~IFCAP_HWCSUM; 3147 else 3148 ifp->if_capenable |= IFCAP_HWCSUM; 3149 if (ifp->if_flags & IFF_RUNNING) 3150 ti_init(sc); 3151 } 3152 error = 0; 3153 break; 3154 default: 3155 error = ether_ioctl(ifp, command, data); 3156 break; 3157 } 3158 3159 TI_UNLOCK(sc); 3160 3161 return (error); 3162} 3163 3164static int 3165ti_open(struct cdev *dev, int flags, int fmt, struct thread *td) 3166{ 3167 struct ti_softc *sc; 3168 3169 sc = dev->si_drv1; 3170 if (sc == NULL) 3171 return (ENODEV); 3172 3173 TI_LOCK(sc); 3174 sc->ti_flags |= TI_FLAG_DEBUGING; 3175 TI_UNLOCK(sc); 3176 3177 return (0); 3178} 3179 3180static int 3181ti_close(struct cdev *dev, int flag, int fmt, struct thread *td) 3182{ 3183 struct ti_softc *sc; 3184 3185 sc = dev->si_drv1; 3186 if (sc == NULL) 3187 return (ENODEV); 3188 3189 TI_LOCK(sc); 3190 sc->ti_flags &= ~TI_FLAG_DEBUGING; 3191 TI_UNLOCK(sc); 3192 3193 return (0); 3194} 3195 3196/* 3197 * This ioctl routine goes along with the Tigon character device. 3198 */ 3199static int 3200ti_ioctl2(struct cdev *dev, u_long cmd, caddr_t addr, int flag, struct thread *td) 3201{ 3202 int error; 3203 struct ti_softc *sc; 3204 3205 sc = dev->si_drv1; 3206 if (sc == NULL) 3207 return (ENODEV); 3208 3209 error = 0; 3210 3211 switch (cmd) { 3212 case TIIOCGETSTATS: 3213 { 3214 struct ti_stats *outstats; 3215 3216 outstats = (struct ti_stats *)addr; 3217 3218 bcopy(&sc->ti_rdata->ti_info.ti_stats, outstats, 3219 sizeof(struct ti_stats)); 3220 break; 3221 } 3222 case TIIOCGETPARAMS: 3223 { 3224 struct ti_params *params; 3225 3226 params = (struct ti_params *)addr; 3227 3228 params->ti_stat_ticks = sc->ti_stat_ticks; 3229 params->ti_rx_coal_ticks = sc->ti_rx_coal_ticks; 3230 params->ti_tx_coal_ticks = sc->ti_tx_coal_ticks; 3231 params->ti_rx_max_coal_bds = sc->ti_rx_max_coal_bds; 3232 params->ti_tx_max_coal_bds = sc->ti_tx_max_coal_bds; 3233 params->ti_tx_buf_ratio = sc->ti_tx_buf_ratio; 3234 params->param_mask = TI_PARAM_ALL; 3235 3236 error = 0; 3237 3238 break; 3239 } 3240 case TIIOCSETPARAMS: 3241 { 3242 struct ti_params *params; 3243 3244 params = (struct ti_params *)addr; 3245 3246 if (params->param_mask & TI_PARAM_STAT_TICKS) { 3247 sc->ti_stat_ticks = params->ti_stat_ticks; 3248 CSR_WRITE_4(sc, TI_GCR_STAT_TICKS, sc->ti_stat_ticks); 3249 } 3250 3251 if (params->param_mask & TI_PARAM_RX_COAL_TICKS) { 3252 sc->ti_rx_coal_ticks = params->ti_rx_coal_ticks; 3253 CSR_WRITE_4(sc, TI_GCR_RX_COAL_TICKS, 3254 sc->ti_rx_coal_ticks); 3255 } 3256 3257 if (params->param_mask & TI_PARAM_TX_COAL_TICKS) { 3258 sc->ti_tx_coal_ticks = params->ti_tx_coal_ticks; 3259 CSR_WRITE_4(sc, TI_GCR_TX_COAL_TICKS, 3260 sc->ti_tx_coal_ticks); 3261 } 3262 3263 if (params->param_mask & TI_PARAM_RX_COAL_BDS) { 3264 sc->ti_rx_max_coal_bds = params->ti_rx_max_coal_bds; 3265 CSR_WRITE_4(sc, TI_GCR_RX_MAX_COAL_BD, 3266 sc->ti_rx_max_coal_bds); 3267 } 3268 3269 if (params->param_mask & TI_PARAM_TX_COAL_BDS) { 3270 sc->ti_tx_max_coal_bds = params->ti_tx_max_coal_bds; 3271 CSR_WRITE_4(sc, TI_GCR_TX_MAX_COAL_BD, 3272 sc->ti_tx_max_coal_bds); 3273 } 3274 3275 if (params->param_mask & TI_PARAM_TX_BUF_RATIO) { 3276 sc->ti_tx_buf_ratio = params->ti_tx_buf_ratio; 3277 CSR_WRITE_4(sc, TI_GCR_TX_BUFFER_RATIO, 3278 sc->ti_tx_buf_ratio); 3279 } 3280 3281 error = 0; 3282 3283 break; 3284 } 3285 case TIIOCSETTRACE: { 3286 ti_trace_type trace_type; 3287 3288 trace_type = *(ti_trace_type *)addr; 3289 3290 /* 3291 * Set tracing to whatever the user asked for. Setting 3292 * this register to 0 should have the effect of disabling 3293 * tracing. 3294 */ 3295 CSR_WRITE_4(sc, TI_GCR_NIC_TRACING, trace_type); 3296 3297 error = 0; 3298 3299 break; 3300 } 3301 case TIIOCGETTRACE: { 3302 struct ti_trace_buf *trace_buf; 3303 u_int32_t trace_start, cur_trace_ptr, trace_len; 3304 3305 trace_buf = (struct ti_trace_buf *)addr; 3306 3307 trace_start = CSR_READ_4(sc, TI_GCR_NICTRACE_START); 3308 cur_trace_ptr = CSR_READ_4(sc, TI_GCR_NICTRACE_PTR); 3309 trace_len = CSR_READ_4(sc, TI_GCR_NICTRACE_LEN); 3310 3311#if 0 3312 printf("ti%d: trace_start = %#x, cur_trace_ptr = %#x, " 3313 "trace_len = %d\n", sc->ti_unit, trace_start, 3314 cur_trace_ptr, trace_len); 3315 printf("ti%d: trace_buf->buf_len = %d\n", sc->ti_unit, 3316 trace_buf->buf_len); 3317#endif 3318 3319 error = ti_copy_mem(sc, trace_start, min(trace_len, 3320 trace_buf->buf_len), 3321 (caddr_t)trace_buf->buf, 1, 1); 3322 3323 if (error == 0) { 3324 trace_buf->fill_len = min(trace_len, 3325 trace_buf->buf_len); 3326 if (cur_trace_ptr < trace_start) 3327 trace_buf->cur_trace_ptr = 3328 trace_start - cur_trace_ptr; 3329 else 3330 trace_buf->cur_trace_ptr = 3331 cur_trace_ptr - trace_start; 3332 } else 3333 trace_buf->fill_len = 0; 3334 3335 break; 3336 } 3337 3338 /* 3339 * For debugging, five ioctls are needed: 3340 * ALT_ATTACH 3341 * ALT_READ_TG_REG 3342 * ALT_WRITE_TG_REG 3343 * ALT_READ_TG_MEM 3344 * ALT_WRITE_TG_MEM 3345 */ 3346 case ALT_ATTACH: 3347 /* 3348 * From what I can tell, Alteon's Solaris Tigon driver 3349 * only has one character device, so you have to attach 3350 * to the Tigon board you're interested in. This seems 3351 * like a not-so-good way to do things, since unless you 3352 * subsequently specify the unit number of the device 3353 * you're interested in in every ioctl, you'll only be 3354 * able to debug one board at a time. 3355 */ 3356 error = 0; 3357 break; 3358 case ALT_READ_TG_MEM: 3359 case ALT_WRITE_TG_MEM: 3360 { 3361 struct tg_mem *mem_param; 3362 u_int32_t sram_end, scratch_end; 3363 3364 mem_param = (struct tg_mem *)addr; 3365 3366 if (sc->ti_hwrev == TI_HWREV_TIGON) { 3367 sram_end = TI_END_SRAM_I; 3368 scratch_end = TI_END_SCRATCH_I; 3369 } else { 3370 sram_end = TI_END_SRAM_II; 3371 scratch_end = TI_END_SCRATCH_II; 3372 } 3373 3374 /* 3375 * For now, we'll only handle accessing regular SRAM, 3376 * nothing else. 3377 */ 3378 if ((mem_param->tgAddr >= TI_BEG_SRAM) 3379 && ((mem_param->tgAddr + mem_param->len) <= sram_end)) { 3380 /* 3381 * In this instance, we always copy to/from user 3382 * space, so the user space argument is set to 1. 3383 */ 3384 error = ti_copy_mem(sc, mem_param->tgAddr, 3385 mem_param->len, 3386 mem_param->userAddr, 1, 3387 (cmd == ALT_READ_TG_MEM) ? 1 : 0); 3388 } else if ((mem_param->tgAddr >= TI_BEG_SCRATCH) 3389 && (mem_param->tgAddr <= scratch_end)) { 3390 error = ti_copy_scratch(sc, mem_param->tgAddr, 3391 mem_param->len, 3392 mem_param->userAddr, 1, 3393 (cmd == ALT_READ_TG_MEM) ? 3394 1 : 0, TI_PROCESSOR_A); 3395 } else if ((mem_param->tgAddr >= TI_BEG_SCRATCH_B_DEBUG) 3396 && (mem_param->tgAddr <= TI_BEG_SCRATCH_B_DEBUG)) { 3397 if (sc->ti_hwrev == TI_HWREV_TIGON) { 3398 printf("ti%d: invalid memory range for " 3399 "Tigon I\n", sc->ti_unit); 3400 error = EINVAL; 3401 break; 3402 } 3403 error = ti_copy_scratch(sc, mem_param->tgAddr - 3404 TI_SCRATCH_DEBUG_OFF, 3405 mem_param->len, 3406 mem_param->userAddr, 1, 3407 (cmd == ALT_READ_TG_MEM) ? 3408 1 : 0, TI_PROCESSOR_B); 3409 } else { 3410 printf("ti%d: memory address %#x len %d is out of " 3411 "supported range\n", sc->ti_unit, 3412 mem_param->tgAddr, mem_param->len); 3413 error = EINVAL; 3414 } 3415 3416 break; 3417 } 3418 case ALT_READ_TG_REG: 3419 case ALT_WRITE_TG_REG: 3420 { 3421 struct tg_reg *regs; 3422 u_int32_t tmpval; 3423 3424 regs = (struct tg_reg *)addr; 3425 3426 /* 3427 * Make sure the address in question isn't out of range. 3428 */ 3429 if (regs->addr > TI_REG_MAX) { 3430 error = EINVAL; 3431 break; 3432 } 3433 if (cmd == ALT_READ_TG_REG) { 3434 bus_space_read_region_4(sc->ti_btag, sc->ti_bhandle, 3435 regs->addr, &tmpval, 1); 3436 regs->data = ntohl(tmpval); 3437#if 0 3438 if ((regs->addr == TI_CPU_STATE) 3439 || (regs->addr == TI_CPU_CTL_B)) { 3440 printf("ti%d: register %#x = %#x\n", 3441 sc->ti_unit, regs->addr, tmpval); 3442 } 3443#endif 3444 } else { 3445 tmpval = htonl(regs->data); 3446 bus_space_write_region_4(sc->ti_btag, sc->ti_bhandle, 3447 regs->addr, &tmpval, 1); 3448 } 3449 3450 break; 3451 } 3452 default: 3453 error = ENOTTY; 3454 break; 3455 } 3456 return (error); 3457} 3458 3459static void 3460ti_watchdog(ifp) 3461 struct ifnet *ifp; 3462{ 3463 struct ti_softc *sc; 3464 3465 sc = ifp->if_softc; 3466 TI_LOCK(sc); 3467 3468 /* 3469 * When we're debugging, the chip is often stopped for long periods 3470 * of time, and that would normally cause the watchdog timer to fire. 3471 * Since that impedes debugging, we don't want to do that. 3472 */ 3473 if (sc->ti_flags & TI_FLAG_DEBUGING) { 3474 TI_UNLOCK(sc); 3475 return; 3476 } 3477 3478 printf("ti%d: watchdog timeout -- resetting\n", sc->ti_unit); 3479 ti_stop(sc); 3480 ti_init(sc); 3481 3482 ifp->if_oerrors++; 3483 TI_UNLOCK(sc); 3484} 3485 3486/* 3487 * Stop the adapter and free any mbufs allocated to the 3488 * RX and TX lists. 3489 */ 3490static void 3491ti_stop(sc) 3492 struct ti_softc *sc; 3493{ 3494 struct ifnet *ifp; 3495 struct ti_cmd_desc cmd; 3496 3497 TI_LOCK(sc); 3498 3499 ifp = sc->ti_ifp; 3500 3501 /* Disable host interrupts. */ 3502 CSR_WRITE_4(sc, TI_MB_HOSTINTR, 1); 3503 /* 3504 * Tell firmware we're shutting down. 3505 */ 3506 TI_DO_CMD(TI_CMD_HOST_STATE, TI_CMD_CODE_STACK_DOWN, 0); 3507 3508 /* Halt and reinitialize. */ 3509 ti_chipinit(sc); 3510 ti_mem(sc, 0x2000, 0x100000 - 0x2000, NULL); 3511 ti_chipinit(sc); 3512 3513 /* Free the RX lists. */ 3514 ti_free_rx_ring_std(sc); 3515 3516 /* Free jumbo RX list. */ 3517 ti_free_rx_ring_jumbo(sc); 3518 3519 /* Free mini RX list. */ 3520 ti_free_rx_ring_mini(sc); 3521 3522 /* Free TX buffers. */ 3523 ti_free_tx_ring(sc); 3524 3525 sc->ti_ev_prodidx.ti_idx = 0; 3526 sc->ti_return_prodidx.ti_idx = 0; 3527 sc->ti_tx_considx.ti_idx = 0; 3528 sc->ti_tx_saved_considx = TI_TXCONS_UNSET; 3529 3530 ifp->if_flags &= ~(IFF_RUNNING | IFF_OACTIVE); 3531 TI_UNLOCK(sc); 3532} 3533 3534/* 3535 * Stop all chip I/O so that the kernel's probe routines don't 3536 * get confused by errant DMAs when rebooting. 3537 */ 3538static void 3539ti_shutdown(dev) 3540 device_t dev; 3541{ 3542 struct ti_softc *sc; 3543 3544 sc = device_get_softc(dev); 3545 TI_LOCK(sc); 3546 ti_chipinit(sc); 3547 TI_UNLOCK(sc); 3548} 3549