rgephyreg.h revision 285830
1/*- 2 * Copyright (c) 2003 3 * Bill Paul <wpaul@windriver.com>. All rights reserved. 4 * 5 * Redistribution and use in source and binary forms, with or without 6 * modification, are permitted provided that the following conditions 7 * are met: 8 * 1. Redistributions of source code must retain the above copyright 9 * notice, this list of conditions and the following disclaimer. 10 * 2. Redistributions in binary form must reproduce the above copyright 11 * notice, this list of conditions and the following disclaimer in the 12 * documentation and/or other materials provided with the distribution. 13 * 3. All advertising materials mentioning features or use of this software 14 * must display the following acknowledgement: 15 * This product includes software developed by Bill Paul. 16 * 4. Neither the name of the author nor the names of any co-contributors 17 * may be used to endorse or promote products derived from this software 18 * without specific prior written permission. 19 * 20 * THIS SOFTWARE IS PROVIDED BY Bill Paul AND CONTRIBUTORS ``AS IS'' AND 21 * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE 22 * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE 23 * ARE DISCLAIMED. IN NO EVENT SHALL Bill Paul OR THE VOICES IN HIS HEAD 24 * BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR 25 * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF 26 * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS 27 * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN 28 * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) 29 * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF 30 * THE POSSIBILITY OF SUCH DAMAGE. 31 * 32 * $FreeBSD: releng/10.2/sys/dev/mii/rgephyreg.h 280667 2015-03-26 05:44:21Z yongari $ 33 */ 34 35#ifndef _DEV_MII_RGEPHYREG_H_ 36#define _DEV_MII_RGEPHYREG_H_ 37 38#define RGEPHY_8211B 2 39#define RGEPHY_8211C 3 40#define RGEPHY_8211F 6 41 42/* 43 * RealTek 8169S/8110S gigE PHY registers 44 */ 45 46#define RGEPHY_MII_BMCR 0x00 47#define RGEPHY_BMCR_RESET 0x8000 48#define RGEPHY_BMCR_LOOP 0x4000 49#define RGEPHY_BMCR_SPD0 0x2000 /* speed select, lower bit */ 50#define RGEPHY_BMCR_AUTOEN 0x1000 /* Autoneg enabled */ 51#define RGEPHY_BMCR_PDOWN 0x0800 /* Power down */ 52#define RGEPHY_BMCR_ISO 0x0400 /* Isolate */ 53#define RGEPHY_BMCR_STARTNEG 0x0200 /* Restart autoneg */ 54#define RGEPHY_BMCR_FDX 0x0100 /* Duplex mode */ 55#define RGEPHY_BMCR_CTEST 0x0080 /* Collision test enable */ 56#define RGEPHY_BMCR_SPD1 0x0040 /* Speed select, upper bit */ 57 58#define RGEPHY_S1000 RGEPHY_BMCR_SPD1 /* 1000mbps */ 59#define RGEPHY_S100 RGEPHY_BMCR_SPD0 /* 100mpbs */ 60#define RGEPHY_S10 0 /* 10mbps */ 61 62#define RGEPHY_MII_BMSR 0x01 63#define RGEPHY_BMSR_100T4 0x8000 /* 100 base T4 capable */ 64#define RGEPHY_BMSR_100TXFDX 0x4000 /* 100 base Tx full duplex capable */ 65#define RGEPHY_BMSR_100TXHDX 0x2000 /* 100 base Tx half duplex capable */ 66#define RGEPHY_BMSR_10TFDX 0x1000 /* 10 base T full duplex capable */ 67#define RGEPHY_BMSR_10THDX 0x0800 /* 10 base T half duplex capable */ 68#define RGEPHY_BMSR_100T2FDX 0x0400 /* 100 base T2 full duplex capable */ 69#define RGEPHY_BMSR_100T2HDX 0x0200 /* 100 base T2 half duplex capable */ 70#define RGEPHY_BMSR_EXTSTS 0x0100 /* Extended status present */ 71#define RGEPHY_BMSR_PRESUB 0x0040 /* Preamble surpression */ 72#define RGEPHY_BMSR_ACOMP 0x0020 /* Autoneg complete */ 73#define RGEPHY_BMSR_RFAULT 0x0010 /* Remote fault condition occurred */ 74#define RGEPHY_BMSR_ANEG 0x0008 /* Autoneg capable */ 75#define RGEPHY_BMSR_LINK 0x0004 /* Link status */ 76#define RGEPHY_BMSR_JABBER 0x0002 /* Jabber detected */ 77#define RGEPHY_BMSR_EXT 0x0001 /* Extended capability */ 78 79#define RGEPHY_MII_ANAR 0x04 80#define RGEPHY_ANAR_NP 0x8000 /* Next page */ 81#define RGEPHY_ANAR_RF 0x2000 /* Remote fault */ 82#define RGEPHY_ANAR_ASP 0x0800 /* Asymmetric Pause */ 83#define RGEPHY_ANAR_PC 0x0400 /* Pause capable */ 84#define RGEPHY_ANAR_T4 0x0200 /* local device supports 100bT4 */ 85#define RGEPHY_ANAR_TX_FD 0x0100 /* local device supports 100bTx FD */ 86#define RGEPHY_ANAR_TX 0x0080 /* local device supports 100bTx */ 87#define RGEPHY_ANAR_10_FD 0x0040 /* local device supports 10bT FD */ 88#define RGEPHY_ANAR_10 0x0020 /* local device supports 10bT */ 89#define RGEPHY_ANAR_SEL 0x001F /* selector field, 00001=Ethernet */ 90 91#define RGEPHY_MII_ANLPAR 0x05 92#define RGEPHY_ANLPAR_NP 0x8000 /* Next page */ 93#define RGEPHY_ANLPAR_RF 0x2000 /* Remote fault */ 94#define RGEPHY_ANLPAR_ASP 0x0800 /* Asymmetric Pause */ 95#define RGEPHY_ANLPAR_PC 0x0400 /* Pause capable */ 96#define RGEPHY_ANLPAR_T4 0x0200 /* link partner supports 100bT4 */ 97#define RGEPHY_ANLPAR_TX_FD 0x0100 /* link partner supports 100bTx FD */ 98#define RGEPHY_ANLPAR_TX 0x0080 /* link partner supports 100bTx */ 99#define RGEPHY_ANLPAR_10_FD 0x0040 /* link partner supports 10bT FD */ 100#define RGEPHY_ANLPAR_10 0x0020 /* link partner supports 10bT */ 101#define RGEPHY_ANLPAR_SEL 0x001F /* selector field, 00001=Ethernet */ 102 103#define RGEPHY_SEL_TYPE 0x0001 /* ethernet */ 104 105#define RGEPHY_MII_ANER 0x06 106#define RGEPHY_ANER_PDF 0x0010 /* Parallel detection fault */ 107#define RGEPHY_ANER_LPNP 0x0008 /* Link partner can next page */ 108#define RGEPHY_ANER_NP 0x0004 /* Local PHY can next page */ 109#define RGEPHY_ANER_RX 0x0002 /* Next page received */ 110#define RGEPHY_ANER_LPAN 0x0001 /* Link partner autoneg capable */ 111 112#define RGEPHY_MII_NEXTP 0x07 /* Next page */ 113 114#define RGEPHY_MII_NEXTP_LP 0x08 /* Next page of link partner */ 115 116#define RGEPHY_MII_1000CTL 0x09 /* 1000baseT control */ 117#define RGEPHY_1000CTL_TST 0xE000 /* test modes */ 118#define RGEPHY_1000CTL_MSE 0x1000 /* Master/Slave manual enable */ 119#define RGEPHY_1000CTL_MSC 0x0800 /* Master/Slave select */ 120#define RGEPHY_1000CTL_RD 0x0400 /* Repeater/DTE */ 121#define RGEPHY_1000CTL_AFD 0x0200 /* Advertise full duplex */ 122#define RGEPHY_1000CTL_AHD 0x0100 /* Advertise half duplex */ 123 124#define RGEPHY_TEST_TX_JITTER 0x2000 125#define RGEPHY_TEST_TX_JITTER_MASTER_MODE 0x4000 126#define RGEPHY_TEST_TX_JITTER_SLAVE_MODE 0x6000 127#define RGEPHY_TEST_TX_DISTORTION 0x8000 128 129#define RGEPHY_MII_1000STS 0x0A /* 1000baseT status */ 130#define RGEPHY_1000STS_MSF 0x8000 /* Master/slave fault */ 131#define RGEPHY_1000STS_MSR 0x4000 /* Master/slave result */ 132#define RGEPHY_1000STS_LRS 0x2000 /* Local receiver status */ 133#define RGEPHY_1000STS_RRS 0x1000 /* Remote receiver status */ 134#define RGEPHY_1000STS_LPFD 0x0800 /* Link partner can FD */ 135#define RGEPHY_1000STS_LPHD 0x0400 /* Link partner can HD */ 136#define RGEPHY_1000STS_IEC 0x00FF /* Idle error count */ 137 138#define RGEPHY_MII_EXTSTS 0x0F /* Extended status */ 139#define RGEPHY_EXTSTS_X_FD_CAP 0x8000 /* 1000base-X FD capable */ 140#define RGEPHY_EXTSTS_X_HD_CAP 0x4000 /* 1000base-X HD capable */ 141#define RGEPHY_EXTSTS_T_FD_CAP 0x2000 /* 1000base-T FD capable */ 142#define RGEPHY_EXTSTS_T_HD_CAP 0x1000 /* 1000base-T HD capable */ 143 144/* RTL8211B(L)/RTL8211C(L) */ 145#define RGEPHY_MII_PCR 0x10 /* PHY Specific control register */ 146#define RGEPHY_PCR_ASSERT_CRS 0x0800 147#define RGEPHY_PCR_FORCE_LINK 0x0400 148#define RGEPHY_PCR_MDI_MASK 0x0060 149#define RGEPHY_PCR_MDIX_AUTO 0x0040 150#define RGEPHY_PCR_MDIX_MANUAL 0x0020 151#define RGEPHY_PCR_MDI_MANUAL 0x0000 152#define RGEPHY_PCR_CLK125_DIS 0x0010 153#define RGEPHY_PCR_JABBER_DIS 0x0001 154 155/* RTL8211B(L)/RTL8211C(L) */ 156#define RGEPHY_MII_SSR 0x11 /* PHY Specific status register */ 157#define RGEPHY_SSR_S1000 0x8000 /* 1000Mbps */ 158#define RGEPHY_SSR_S100 0x4000 /* 100Mbps */ 159#define RGEPHY_SSR_S10 0x0000 /* 10Mbps */ 160#define RGEPHY_SSR_SPD_MASK 0xc000 161#define RGEPHY_SSR_FDX 0x2000 /* full duplex */ 162#define RGEPHY_SSR_PAGE_RECEIVED 0x1000 /* new page received */ 163#define RGEPHY_SSR_SPD_DPLX_RESOLVED 0x0800 /* speed/duplex resolved */ 164#define RGEPHY_SSR_LINK 0x0400 /* link up */ 165#define RGEPHY_SSR_MDI_XOVER 0x0040 /* MDI crossover */ 166#define RGEPHY_SSR_ALDPS 0x0008 /* RTL8211C(L) only */ 167#define RGEPHY_SSR_JABBER 0x0001 /* Jabber */ 168 169/* RTL8211F */ 170#define RGEPHY_F_MII_PCR1 0x18 /* PHY Specific control register 1 */ 171#define RGEPHY_F_PCR1_MDI_MM 0x0200 /* MDI / MDIX Manual Mode */ 172#define RGEPHY_F_PCR1_MDI_MODE 0x0100 /* MDI Mode (0=MDIX,1=MDI) */ 173#define RGEPHY_F_PCR1_ALDPS_EN 0x0004 /* Link Down Power Saving Enable */ 174 175/* RTL8211F */ 176#define RGEPHY_F_MII_SSR 0x1A /* PHY Specific status register */ 177#define RGEPHY_F_SSR_S1000 0x0020 /* 1000Mbps */ 178#define RGEPHY_F_SSR_S100 0x0010 /* 100Mbps */ 179#define RGEPHY_F_SSR_S10 0x0000 /* 10Mbps */ 180#define RGEPHY_F_SSR_SPD_MASK 0x0030 181#define RGEPHY_F_SSR_FDX 0x0008 /* full duplex */ 182#define RGEPHY_F_SSR_LINK 0x0004 /* link up */ 183#define RGEPHY_F_SSR_MDI 0x0002 /* MDI/MDIX */ 184#define RGEPHY_F_SSR_JABBER 0x0001 /* Jabber */ 185 186#endif /* _DEV_RGEPHY_MIIREG_H_ */ 187